Search Documents

By L. Haavanlammi

Iron is a significant component of all copper concentrates leached in the HydroCopperTM process. The metals in the concentrate are leached in a chloride solution by oxidation with cupric ions. Copper enters into the solution as a cuprous chloro¬complex. Iron dissolves at the same time in the ferrous form, but it is immediately oxidized to the ferric state. Oxidation is effected by sparging air or oxygen into the leaching reactors. Because the pH is 1 - 2.5, ferric ion precipitates as akaganeite (T<90°C) or hematite (T> 90°C). Arsenic, antimony and the main part of the bismuth co-precipitate with iron and report to the leach residue. Cupric leaching is faster than iron oxidation; thus, leaching of low-iron concentrates (secondary copper minerals) is quicker than leaching high iron concentrates (chalcopyrite). Pyrite does not dissolve during copper leaching, but is oxidized slowly at higher redox-potentials after the copper has been leached.

Jan 1, 2006

By D. J. Hains

IN this paper we shall examine the Why, Where and How concerning the agglomeration of iron ores and concentrates. Fig. l answers the questions @f why there is so much interest at the present time in the art of agglomeration. The use of sinter or pellets in the blast furnace has materially increased their rated •capacity. ':'President Hains Company Ltd. Engineering J. S. McMahon ( 1) reports an increase from 653 tons of .pig iron per day to 1140 tons of pig iron per day with the use of a 100 per cent sinter burden on one of his blast furnaces. In the United States the use of 100 per cent pellets has increased pig iron production from approximately 1800 tons per day to over 3000 tons pig iron per day (2). In our economic system the general objective is to produce more and better commodities cheaper. Fig. 2 shows the decrease in coke consumption with increased tonnages from the furnaces when using -

Jan 1, 1961

By R. H. McCorkell

Radon emanation rates. J. and compositions of materials from the Canadian Certified Reference Materials Project (CCRMP) indicate that the fraction of the Rn produced that escapes, E, is usually 1% to 8% and the 238U decay chain is nearly in secular equilibrium. For some Chinese ore standards, E values are higher than f or the CCRMP materials. Standard ore tailings have 2/oPb concentrations higher than expected from their 226Ra concentrations and Rn escape rates (12 - 34%) . Biological materials have E ˜100%, their ash E ˜0%. Pelletizing ore powders at 20 000 lb/in2 reduces J by only 20 - 40% but only 2% of Rn escapes from pressed Li2B4O7 pellets and 0.01 - 0.04% from fused Na2B4O7 or Li2B4O7 discs. Large, difficult-to-explain random variations in J are observed in some situations but several highly reproducible ways of measuring emanation rates have been found.

Jan 1, 1986

By Joseph H. Harris

Shebandowan Mine presents a unique opportunity for the mining industry to demonstrate its willingness and ability to use electrical energy effectively. The mine is a typical 250D-ton/day operation supplied by a i5-MVA power transformer. it is a recent, up-to-date design and operates on a four-day/week, two-shift/day basis. The paper outlines an energy profile based on historical data. It accurately describes the individual and total energy input For: (1) production and non-productive junctions; (2) production and down-time periods; (3) peak and average activity levels; and (4) principal energy utilization equipment. A comparison is then made of production data to electrical data, and production and electrical data to design data. The paper concludes that energy management has an important benefit for the mining industry by assisting in maintaining a competitive operation through reduced costs and fewer production slow-downs in the event of energy shortages.

Jan 1, 1979

By H. C. W. Bosman

"Over the past five years, contributions from geologists and mining engineers were instrumental in the successful development of MEPS. It is a system of FORTRAN programs specifically designed to be used by mining personnel to solve geological and mining problems. MEPS is a flexible keyword-driven system. Extensive error editing procedures significantly reduce the time required to proceed from problem recognition to solution. Possibly the most attractive feature of MEPS is that computer solutions may be guided or selectively modified to obtain desired solutions. Some highlights of MEPS are:1. Vocabulary that is familiar to mining people.2. Geological data storage and retrieval.3. Statistical analysis and variograms.4. Contour maps of assays and geological horizons.5. Trend surface analysis with residual evaluation.6. Ore reserve calculations.7. Open-pit mine design.8. Marginal profitability calculations on pit walls.9. Production scheduling.10. Vertical cross-section plots indicating pit outlines, ore grade contours and selected geological horizons."

Jan 1, 1973

By Michelia Alba, Ronaldo S. Sampaio, Davi S. Braga, Mathieu Dubé

Climate change is pressuring industries and governments for decarbonization commitments, research, testing, and use of best practices to achieve the target of global warming below 1.5/2 °C. As it accounts for as much as 7% of all global CO2 emissions and 7% of energy consumption, the steel sector needs to address this issue with extended efforts. This paper provides information on the key potential of renewable biochar as an alternative fuel for pellet production. It also summarizes the successful application of biochar in a pioneering case study as the main fuel for a Grate-kiln pellet plant in Brazil, as well as the study of its use to replace coke and anthracite as an additive for iron ore pellets and other possible applications in the steel industry in COREM's precompetitive research & innovation program. The final discussion reveals the large quantity of biochar required by the Brazilian and Quebec scenarios for reducing CO2 emissions of iron ore pelletizing plants.

Jan 1, 2023

By M. E. Hurst

Introduction Between 1903 and 1905, W. Mclnnis, of the Geological Survey of Canada, made a micrometer traverse of the Kawinogans (Crow) river from Kapkichegimaga lake to its junction with the Otoskwin river. He reported that a belt of Keewatin rocks, 1 to 4 miles wide, was exposed along the course of the river for 17 miles east of Kapkichegimaga lake. Prospectors and exploration companies paid little attention to the mineral possibilities of this belt until the summer of 1928 when, with the adoption of airplane transportation, the area became readily accessible. Within a short time widespread interest was aroused by the announcement of attractive finds, and a mild rush followed. During the winter months, hundreds of claims were staked on either side of Crow river for 12 miles east of Pickle lake. In the summer of 1929, much of this ground was systematically explored and a considerable amount of development work was done on the known deposits.

Jan 1, 1930

The Carboniferous sedimentary rocks of southwestern Newfoundland merit investigation because of petroleum, salt and gypsum possibilities and indications of base metallization along the equivalent of the Horton-Windsor con-tact. In this paper, Lower Mississippian (Anguille) strata are divided into three formations: (1) the Cape John below, (2) the Snakes Bight and (3) the Seacliffs. A correlation between these formations and the Craignish, Strathlorne and Ainslie formations of the Horton group? in western Cape Breton Island is suggested. The criteria for the Anguille subdivision are essentially lithological, but preliminary study of included spore assemblages suggests more precise interformational correlations between Anguille and Horton sequences. The re-measured lower portion of the type section of the Codroy group is presented to define more clearly the stratigraphic position of numerous gypsum and limestone beds. Because of rapid facies changes within the Codroy group a simplified two-fold division into upper and lower units is proposed on the grounds of

Jan 1, 1964

By Y. Thibault, G. Deschênes

An open-pit mine, located in Mexico, processes an ore a rate of 4000 tpd, using conventional cyanidation and AYR. A laboratory study was conducted to increase silver extraction and to reduce the concentration of cyanide in leaching. The sample contained 0.41 g/t Au, 125 g/t Ag, 99% gangue minerals, 0.7% pyrite, 0.07% sphalerite, 0.03% chalcocite. Silver was present as acanthite, stromeyerite, silver mercury/halogen, silver with copper in solid solution and jalpaite. The plant conditions (2400 ppm NaCN) produced 90.2% gold extraction (residue at 0.04 g/t Au) and 92.7% silver extraction (leach residue at 9.1 g/t Ag). The CELP (CANMET Enhanced Leaching Process) produced 97.0% silver extraction (residue at 3.8 g/t) and 90.2% gold extraction using 500 ppm NaCN. The incremental gross revenue was estimated at $US7.6 million and the reduction of cyanide costs was $2.9 million per year (79%).

Jan 1, 2011

By Nathaniel S. Scott

Caland Ore Company Limited, a subsidiary of Inland Steel Company of Chicago, Illinois, leased an iron ore deposit from Steep Rock Iron Mines Limited on January 1, 1953.. This deposit lay underneath a lake and was covered with 161,000,000 cubic yards of Jake bottom material, mainly silt. Removal of this material was done on a contract dredging basis. This contract was divided into a plant phase and an operating phase. The plant phase consisted of supplying two cutter-type suction dredges, each with two booster pumps in the discharge lines. All six pumps were centrifugal, had 36" discharges and were powered by 10,000 horsepower electric motors. Peak demand was 59,157 kilowatts. One hundred and forty miles of steel tower line were built to bring power to the site. The balance of the plant consisted of tugs, 12 miles of discharge line, varying from 36" diameter to 42" diameter and attendant land-based equipment. A number of interesting dams were constructed

Jan 1, 1961

By G E. Craig, W. M. Williams

A simple, easily constructed apparatus suitable for the zone refining of iron and other reactive materials is described. After eight passes at one inch per hour, the iron produced showed a marked drop in hardness to 49 Brinell. In addition, an arbitrarily -defined recrystallization temperature was lowered by about 35°C and the rate of grain growth greatly increased. CERTAIN materials, of which iron is one, are so reactive that they cannot be zone refined in any known container without becoming contaminated. For such substances, the floating zone method ( 1) may be used. In this method, the specimen is supported vertically in an inert atmosphere and the molten zone supports itself by its own sur-face tension. The method was first applied to silicon (2) and has since been used for other reactive metals such as zirconium and titanium. Smith and Rutherford (3) have previously reported on the floating zone refining of iron; the efficiency of the method for reducing the car-bon content was demonstrated on

Jan 1, 1962

By Z. D. Hora

Sedimentary phosphate-bearing rocks are found over a considerable area of so utheastern British Columbia that extends from Fernie east to the Alberta-British Columbia boundary and from the International Boundary northward to the headwatei: s of the Elk River. Phosphatic beds occur at the following four stratigraphic levels: 1. lower part of the Banff-Exshaw sequence of Mississippian age; 2. lshbel Formation of Permian age; 3. base of the Fernie Group of Jurassic age; 4. belemnite bed within the Rock Creek Member of the lower part of the Fernie Group. To date, considerable tonnages of phosphate rock have been proven in the area. However, no commercial production has been initiated because of a relatively low P2O5 grade. Data on assays and thicknesses of the phosphatic beds are in part recalculated from the paper by Telfer (I 933) and in part from assessment reports filed at the British Columbia Ministry of Energy, Mines and Petroleum Resources.

Jan 1, 1984

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973

By Ben Sheneider

AT THE Flin Flon plant of the Hudson Bay Mining and Smelting Co., Limited there are two types of multiple hearth furnaces used in the roasting of sulphides. This pa-per will deal primarily with the wedge-type furnace in the roasting of zinc concentrates. The other furnace, the Nichols-Herroshoff type, is used in the copper smelter and is described in the papers given by (1) J. H. Ambrose in 1935 and (2) R. E. Mast and G. H. Kent in 1954. The design and operation of these roasting furnaces at the present time is essentially the same as given in the write-up in 1954. No at-tempt will be made here to describe these furnaces, except to mention that there are five Nichols-Herreshoff multiple-hearth furnaces, four of which are used to roast a dried mixture of copper concentrate, zinc plant residue, and flux, before this material is fed to the reverberatory furnace.

Jan 1, 1961

By P. G. Thornhill

EARLY in 1951, Falconbridge undertook a research program aimed at the development of a sulphate roasting process for the recovery of the non-ferrous rnetals from the nickeliferous pyrrhotite fraction of Falconbridge ore, in order to reduce the tonnage of iron entering the srnelter. Such a method, it was hoped, would permit a high recovery of the nickel from pyrrhotite otherwise entering the smelter feed, thus not only raising the grade of the latter and reducing its iron content, but also providing an iron oxide residue useful as a source of by-product iron ore. At an early stage in the exploratory laboratory test work it was found that the degree to which the nickel could be solubilized by the sulphating roasting treatment was limited by particle size and the ex-tent to which the pyrrhotite concentrates were freed of the nickel occurring as physically separable pentlandite, a mineral relatively difficult to roast. ( 1) Thus the program

Jan 1, 1961

By J. C. White

"This paper was prepared for and presented at a lecture series on ""Materials Randling"" at McGill University. The development of trackless mining at Gaspe Copper Mines, Limited is described, showing the changes in mining method and the part played by the mobile equipment in the evolution of this highly mechanized underground operation. Comparisons of loading and hauling machines are given and an attempt is made to predict some possible future developments.INTRODUCTIONTHE PROPERTY OF GASPE COPPER MINES LIMITED is located in the Gaspe Peninsula of the Province of Quebec, 60 miles west of the village of Gaspe and 25 miles south of the St. Lawrence River. The original discovery of low-grade ore was made at Copper Mountain in 1921. Subsequent exploration revealed the richer Needle Mountain orebodies, and eventually in 1951 the decision was made by Noranda Mines to build the mining, concentrating and smelting complex (Figure 1). Construction and development of the mine was commenced in 1952 and production started in 1955."

Jan 1, 1968

By T. Gerritsen, C. Martinez, F. Stober, T Ma, J. R. Frias, M. Sedighy, J. Janzen

Electrode control systems regulate power by physically positioning electrodes. Due to the weight and inertia of the electrodes and hoist equipment, this is a relatively slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +/- 20% or more around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicana&apos;s laterite nickel furnace, yielding excellent results with a 3 to 1 reduction in power fluctuations.

Jan 1, 2005

By D. M. Baird

"THE Island of Newfoundland lies on the extreme eastern edge of the continent of North America and at the extreme northeastern end of the Appalachian geological province. Its belonging to the Appalachian province is shown in the geological history of the region and in the rock types and structures.Geosynclinal sedimentation in early and middle Palaeozoic times was interrupted by Taconic and, more profoundly, by Acadian, mountain building activity. Mid-Palaeo-zoic intrusions range from masses of serpentinized ultrabasic rocks to granite batholiths. A Carboniferous overlay of continental and shallow, drying sea types covers the earlier developed complex. Local basins in these times were filled with products of the erosion of tl1e earlier rocks, and, locally, grew the right kind of vegetation to make thin, discontinuons seams and pockets of coal. Post-early Pennsylvanian history is one of erosion and pene-planation with renewal of movement along many of the older fault systems."

Jan 1, 1960

By W. E. Hale

An area of about 7,000 square miles within the eastern part of the Grenville Sub-province is underlain chiefly by granitic gneisses. There are, however, some exposures of mafic rocks which warrant further investigation, and some attractive structures, particularly basins, which deserve additional economic consideration. T HIS paper describes in a very general fashion the economic and geological features of an area of about 7,000 square miles on the north shore of the Gulf of St. Lawrence in the eastern part of the Grenville Sub-province (Figure 1). The scarcity of published geological data on this part of the Cana-dian Shield (DePuyjalon, 1899 and Longley, 1944) justifies the presentation of these tentative results. It should be appreciated, however, that the information which follows was acquired in a rapid reconnaissance designed specifically to out-line what might be interpreted as favourable geological environments for the occurrence of economic minerals, rather than to produce an authoritative analysis of the geological history of the region.

Jan 1, 1962

By J R. O Walli

Large production shafts can be successfully sunk through the ubiquitous Blairmore formation of southern Saskatchewan by employing the freezing process and by the installation of a cast iron tubbing lining. Although the freezing technique for shaft sinking and the use of cast iron tubbing to preserve the shaft are new to the North American continent, these procedures have been employed in Europe for the past eighty years. More than 200 shafts, covering a wide variety of ground conditions, have been sunk by the freezing process, and most of these have been lined with cast iron tubbing. The No. 1 shaft of International Minerals and Chemical Corporation, near Esterhazy, Saskatchewan, comprises the first major example in Canada of the employment of European methods to overcome extremely difficult ground conditions. The Blairmore formation was solidified by the deep freezing process, employing a lithium chloride solution as the refrigerant, with input temperatures ranging to -55°F

Jan 1, 1964