Search Documents

By A. T. Jakubick, A. MacG. Robertson

This paper reviews key issues related to the placement of dry (soil) covers on extremely weak, compressible fine tailings. The design and construction of soil covers on such tailings often presents a formidable challenge to the geotechnical as well as the environmental engineer due to the low shear strength, poor traffic ability, and high settlement of under consolidated tailings at the time of reclamation. The geotechnical issues to be considered include: (1) consolidation of near-surface tailings to achieve strength gains, improve traffic ability, and allow safe placement of initial cover layer; (2) stability of tailings slopes during dewatering of tailings ponds and/or cover placement; and (3) long-term settlement of tailings and its impact on cover integrity and final surface shaping. The environmental issues to be considered include: (1) management of contaminated (free) pond water; (2) management of contaminated pore water expelled during tailings consolidation; and (3) management of (uncontaminated) surface water on top of the cover. This paper summarizes recent experiences gained in a large uranium tailings reclamation project. It is concluded that a careful consideration of both geotechnical and environmental issues during the planning stages greatly reduces the costs and environmental risks associated with fine tailings reclamation.

Jan 1, 2000

By Jin Liu, Torstein A. Utigard

At its Copper Cliff Smelter, Vale Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces. Coke supplies a minor proportion of the process heat requirements, limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as SO2 in the flash furnace. Extensive experiments were conducted in a miniplant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. The introduction and description of the experimental set up were given in Part 1 of this paper and an early paper published in Yazawa symposium1 together with the results and some in depth discussion on metallurgy. This paper intends to discuss the kinetics of the miniplant flash furnace testwork.

Jan 1, 2015

By Dean S. Rogers

"In February 1980, Dome Mines Limited announced a $50 million expansion program which would result in a 50% increase in mill capacity from the present 1,815 tonnes per day to an eventual production rate of 2, 720 tonnes per day in the year 1984. As an integral and necessary part of this planned expansion, a new vertical production shaft, No. 8 Shaft, would be sunk from surface to a depth of 1,645 metres.Throughout the seventy-year history of mining at the Dome, gold has been found in a number of different rock types and in association with a number of different structural settings. However, the key to successfully locating ore deposits lies in the recognition of the favourable environments in which they generally occur. First and foremost, the exercise of locating the No. 8 shaft became an exercise in geological deduction based on the projection of these favourable lithologic environments.In November 1980, after detailed engineering work was completed, the total cost of the project was estimated at $75.5 million 1980 dollars or $91 million dollars allowing for inflation over a four-year construction period. These estimates include the shaft, significant replacement and alterations to the milling process, and an upgrading of the plant."

Jan 1, 1982

By J. Lui

At its Copper Cliff Smelter, bulk nickel and copper concentrate is processed in two Inca flash furnaces and Peirce Smith converters to produce Bessemer matte containing 0.6%Fe. After slow cooling and Matte Separation, Bessemer matte is converted into three main products using magnetic separation and flotation technology: (1) a nickel containing chalcocite concentrate (MK); (2) two types of copper containing nickel sulfide (ME and MR); (3) metallics (MYN). MK is further processed in the Inca top blowing bottom stirring MK Reactor to produce semi-blister copper containing ~4%Ni and ~3±1 %S. The semi-blister copper is then purified in the multi-purpose vessels (MPV) to produce blister copper by reducing Ni, Fe and S content through oxidation. High melting point NiO is formed inside the MPVs. The accumulation of solid NiO and other oxides requires periodic cleaning by adding reductant and furnace matte, a unique process called "washout" at Inca. For many years, the reductant used for the "washout" process has been 15%Si Ferro-silicon. With increasing cost and limited suppliers for 15%FeSi, alternative reductants were pursued. This paper summarizes the development and commercialization of new alternative reductants for MPV "washout".

Jan 1, 2007

By L. Tong

"The oxidation of Quebracho was evaluated by acid-butanol assay, which indicates depolymerization of Quebracho. Anthocyanidin, an oxidation product of Quebracho, is stable at 95?C for up to 2 h. The ionization, complexation, and oxidation properties of Quebracho were discussed. Complexation of metal-Quebracho occurs at ambient temperature. The formation of complex precipitates is influenced by the acidity of the solution. Temperature is another important parameter that influences the oxidation and the complexation of Quebracho. Quebracho-ferric complex precipitate forms at 90?C, 0.1 mol/L H2SO4. The formation of Quebracho-metal complex in the leach solution is a possible reason for the consumption of Quebracho. Quebracho molecules adsorption on the mineral surface is reduced by consumption of Quebracho, resulting in poor sulfur dispersing effect in the leaching process. INTRODUCTIONQuebracho is used as a sulfur dispersing agent (SDA) in the pressure leaching of zinc concentrate as stated in U.S. Patent No. 3,867,268 (1975). It prevents the zinc sulfide particles from being coated with molten sulfur, thus preventing the inhibition of the zinc leaching reaction. Recently, the sulfur dispersing effect of Quebracho was investigated in the oxygen pressure leaching of nickel concentrate. The oxygen pressure leaching of pentlandite can be represented by reactions 1-3."

Jan 1, 2012

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By W. W. Cummings

Canada's only current tungsten producer started up in 1962 with a small open-pit mine on the Flat River , 180 air miles north of Watson Lake, Yukon Territory. The orebody was in a contact-metamorphic skarn zone and contained about 1.5 million tons of ore grading an estimated 2.47% W03 and 0.5% copper. Near the end of the open pit , a new zone was discovered on the lower limb of the same structure, and the decision to go underground was made in 1972. The new "E Zone" contains over 4 million tons of ore grading an estimated 1.6% W03 and 0.28% Cu , and has been supplying the concentrator at about 175,0 00 tons/ year since late 1974. A continuing program of change and up-grading is necessary in the conversion from a seasonal open-pit mine with limited life to an underground operation with twenty years of reserves. Changes are necessary in plant and services as well as the mine. Also, environmental protection requirements have changed from rudimentary to rigorous over the life of the operation. This paper sums up the changes in the operation since 1971 and outlines the changes yet to come.

Jan 1, 1977

By L. M. Pidgeon

MAGNESIUM metal, with a specific gravity of 1.73, is two-thirds the weight of aluminium and one-quarter that of steel. It is the lightest metal which is stable in the atmosphere. Before the war it had begun, though somewhat slowly, to take a place among the established metals. In 1939, magnesium production on this continent amounted to some 3,000 tons per annum and was confined to one company. At that time, Germany produced perhaps 20,000 tons. The advent of war, however, increased the demand to fantastic heights and introduced production problems of unprecedented magnitude. By the end of 1943, North American production is expected to reach 300,000 tons per annum (1), an increase of one hundredfold. Such a rate of expansion has not been witnessed previously in the history of metallurgy. It has given the metallurgist an opportunity to try new production methods and to learn in a short time what might otherwise have taken many years. The metallurgy of magnesium is still in its formative years and at this time widely different production methods are in operation side by side. This paper will discuss these methods in so far as information is available for publication at this time. A general description of the new Canadian industry will be included.

Jan 1, 1944

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By A. Gourlie

"This paper describes the performance properties of a new 95 ksi minimum yield strength, oil well casing grade designed specifically to resist hydrogen sulphide stress corrosion cracking, SSCc. The new grade, Soo-95SS, demonstrates NACE Tensile threshold values greater than 90% specified minimum yield strength, SMYS, and NACE Bent Beam values in excess of 12.7 x 1()4 psi. The new Soo-9588 grade also exhibits superior collapse and notch toughness values. IntroductionIn recent years, a trend toward casing grade specialization has resulted in the introduction of numerous proprietary grades designed specifically for particular production environments, In response, Algoma Steel has developed, as part of a "" grade for service"" philosophy, two new 95 ksi minimum yield grades. The two grades are Soo-95, High Collapse (HC), and Sour Service (SS). This paper describes the development of Soo-95 Sour Service.Four main objectives were established:1. Definition of the steelmaking and continuous cast processing practices2. Determination of the acceptable maximum and minimum levels for all chemical elements3. Definition of special processing requirements4. Definition of the physical characteristics and ranges of the product properties.This paper provides a description of the experimental approach, followed by a presentation and discussion of the trial results . Finally, a number of conclusions are given."

Jan 1, 1988

By J. Duncan Keppie

"Auriferous quartz veins occupy zones of dilation. Foldgenerated dilation zones are systematically distributed and are dependent upon the folding mechanism. Comparison of natural and theoretical folds indicates that different mechanisms operated in the Halifax and Goldenville formations.In the slates of the Halifax Formation, the folds are of similar type and internal strain is most intense in the limbs. This internal strain is probably accommodated with little or no dilation.In the meta-sandstone and slates of the Goldenville Formation, a combined flexural and tangential longitudinal strain mechanism, modified by pure strain, produced the folds. Tension fissures produced by this mechanism are: (a) saddle 1'eef veins in slate horizons, (b) veins normal to bedding in meta-sandstone layers in the fold hinges,(c) veins along faults in the cores of tight fold hinges and (d) zones of en- échelon veins in slate honzons in the limbs of folds. Because veins in fold hinges (a, b and c above) account for most of the gold production in the Meguma Group, other factors controlling the distribution and size of these veins are summarized below.1. The size of saddle reef veins is controlled by the curvature of the fold hinge. Thus, a Curvature Index greater than 600 degrees indicates a promising prospect, where"

Jan 1, 1976

By R P. Douglas

During 1955, Cominco commenced an exploration pro-gram in northern New Brunswick; in the following year, what is now the Wedge mine was discovered. The mineralization is mainly pyrite, with associated chalcopyrite and minor amounts of sphalerite and galena. The property was brought into production at 750 tons per day in early 1962. The ore is trucked 10 miles to the Heath Steele concentrator, where a copper concentrate grading about 19.5 per cent is produced and shipped to the Japanese markets through the port of Dalhousie, New Brunswick. Introduction THE Wedge mine, owned by The Consolidated Mining and Smelting Company of Canada Limited (Cominco), is located in the Newcastle-Bathurst area of New Brunswick. It is 42 miles by road northwest of Newcastle and 37 miles southwest of Bathurst (Figure 1). The mine is located on the north side of the Nipisiquit river in one of the more mountainous areas of the Province, the local relief rising to 1,500 feet above sea level. There is an almost complete forest cover of mixed hardwoods and conifers -the val-leys and hillsides being covered by balsam, spruce and pine, the swamps by cedars and black spruce and the highlands by mixed hardwoods.

Jan 1, 1965

By Nick Vagenas

"Loading and transportation are important activities of the mining process. Automation of these activities in underground hard rock mining has been discussed for a long time. This paper deals with the performance evaluation of a prototype automatic Load-Haul-Dump (LHD) vehicle (a 7-ton GHH LF LHD model) operating in Zinkgruvan mine, Sweden. The purpose of the data analysis is to evaluate the operational and maintenance characteristics of the automatic LHD system in the mine. Graphical and numerical methods have been used for the statistical analysis of the data. IntroductionDuring the past years, the idea of integrated automation and tele-operation on Load-Haul-Dump (LHD) machines (Fig. 1) has attracted considerable interest in the Swedish mining industry. This is mainly due to the demand for improvement in the working environment and due to the rapid development of economic and reliable microprocessors for mining vehicles. Several advantages can be foreseen with the application of a Remote-controlled/Automatic LHD (RAL) system in underground mining. Some of them are (1)':• better utilization of working hours;• less interruption in production at shift changes;• better operational control of a fleet of vehicles;• improved safety; and• one operator may be able to operate more than one vehicle simultaneously."

Jan 1, 1993

"INTRODUCTIONThe Department of Energy, Mines and Resources has recently developed two automatic controls for use in the cyanidation circuits of Canadian gold mills. These controls are the alkalinity probe and the Continuous Cyanide Titrator both of which are discussed in the paper ""Instrumentation in the Cyanide Process"".(1)In May 1966 these process controls and associated recording equipment were installed in the Bralorne mill by two Scientific Officers from the Department. The object was to determine if the equipment was amenable and applicable to this particular circuit. The purpose of this paper is to discuss the performance of the equipment over a test period of 4 months.CONCLUSIONSThe results of test work to date indicates that both the Conductivity Probe and the Continuous Cyanide Titrator would be an as set to the operation of the Bralorne mill.The conclusions are generalized as follows:-(1) At a milling rate of 100, 000 tons per year the expected reductionin reagent consumption would give a direct saving of 37, 660 lbs of lime@$0.030 per lb and 15, 790 lbs of sodium cyanide@ $0.175 per lb. Such cost savings would pay for the equipment and installation costs within a 30 month period"

Jan 1, 1967

By J. W. Craig

THERE are, broadly speaking, three classes of refractories: acid, basic, and neutral. Fireclay, diaspore, silica, and the sillimanite group of minerals are included in the acid class, which for the most part are not very resistant to basic slags. The neutra! class includes chrome, graphite, and silicon carbide, while most important in the basic class are magnesite and dolomite. Although chrome is a neutral refractory, it has no sharp distinction from magnesitic refractoriness. The two are mineralogically (1) and chemically related, and there is available on the market a complete range of brick from straight chrome to straight magnesite. In many indus trial applications, one. type may be replaced by another. The present paper is confined entirely to such refractories. The following types of basic and neutra! brick, each sold under sorne special trade name, are available for use in Canada: (1) Burned chrome from crude ores (2) Burned chrome from treated ores (3) Chemically bonded (unburned) chrome-magnesite ( 4) Burned chrome-magnesite (5) Chemically bonded ( unburned) magnesite-chrome (6) Chemically bonded (unburned) high-iron magnesite (7) Burned high-iron magnesite (Regular) (8) Burned low-iron magnesite (9) Burned olivine-magnesite (10) Burned magnesitic dolomite-chrome (Magnecon) (11) Chemically bonded magnesitic dolomite-chrome (Magmecom) (12) Dolomitic brick

Jan 1, 1936

By I. Raheb, M. Y. Debili

"A set of Al-Co binary alloys (with respectively in weight percent 10%, 20%, 30%, 40%, 50% and 60% Co) have been studied by X-ray diffraction at the as compacted state. The structural evolution according to cobalt addition shows special features as the apparition of fcc cobalt and hcp cobalt beside aluminium in some cobalt compositions of the Al-Co mixtures using only cold compaction without sintering at high temperature. Figure 1 Cobalt is not a common alloying element in aluminium because its solubility is very low [1]. According to the pressure-temperature phase diagram, Co is known to exist in two allotropic forms: a low-temperature hcp phase and a high-temperature fcc phase [2-3]. At room temperature, Co is stable in the hcp form but it transforms to the fcc form when it is heated to above the transition temperature 695K. Powder aluminium and cobalt (99.999 %) were used in the proportions defined according to the required compositions. The total mass of the samples to be elaborated was between 8 g and 10 g. Cold compaction of mixed powder (Al-Co) under an uniaxial load of 10 MPa has been achieved to obtain a dense product (60%)."

Jan 1, 2015

By R. J. Traill

Introduction Following the discovery of high-grade deposits of pitchblende in the Great Bear Lake area of the Northwest Territories by Mr. Gilbert LaBine in May, 1930, samples were submitted to the Mines Branch for examination and investigation as to suitable methods of treatment (1). The purpose of this paper is to present, briefly, the results of the investigative work conducted on the ores and an outline of the methods developed for the extraction of the radium content and recovery of the by-products. The paper is presented in two parts. Part I gives a review of the history of radium production and of the principal processes used in other countries. Part II describes the work and gives the results of the Mines Branch investigation. Part 1-Radium Production In Other Countries Historical Outline Uranium was discovered in 1789, and more than a century later Madame Curie, while studying the physical properties of this element, observed that the ore of uranium exhibited greater activity than the pure uranium com-pounds she had prepared and traced the cause to the presence of a new element which she named radium. Eventually, research proved radium to be a disintegration product of uranium, and always present in uranium ores.

Jan 1, 1933

By E. Swartzman

"IntroductionGENERALLY, the necessity for mining coals of higher impurity content, the drive for lower costs by intensive mine mechanization, changing market requirements, and the increasing competition of oil and natural gas, have continued to result in an upward rise in coal preparation, and have necessitated a more intensive study of coal preparation problems.Increasing adoption of •continuous mining equipment, for example, is introducing new problems in coal preparation. Limited experimental work in the United States (1) shows that the effect of the continuous miner on size distribution varies with the characteristics of the seam. In some seams, the fines problem is lessened, in others it is greatly aggravated. Generally there is a decrease in the relative amount of the top sizes (plus 2 in.) and a substantial increase in the intermediate sizes (down to about 1/8 in.). Contrary to expected results•, where continuous miners with vertical-moving cutting heads are used, an increase in impurities in the slack sizes does not necessarily occur where draw-slate is taken. This is because the draw-slate tends to be kicked out in lump form. However, if a seam contains bands •and lenses of impurities they are bound to be in the mined product."

Jan 1, 1952

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

The scanning electron microscope (SEM) was primary developed for imaging applications. With the introduction of the Si(Li) energy dispersive spectrometer (EDS), simultaneous imaging and x-ray microanalysis became possible. However, long working distance and high current were needed because the position and small solid angle of the EDS detector. The high spatial resolution is generally obtained at short working distance with a SEM. Unfortunately x-ray microanalysis is never performed in the best imaging conditions. The annular silicon drift detector system is inserted below the objective lens which gives a higher solid angle (up to 1.3 sr). In consequence, a lower working distance and probe current can be used. An improved spatial resolution becomes possible during x-ray microanalysis. With this x-ray detector installed on a cold-field emission scanning electron microscope, quantitative x-ray microanalysis with high spatial resolution at low beam energy and low current becomes possible with the possibility of using the various different type of imaging at the same time. Also, since the count rate can be as high as 1,500 kcps, which lowers significantly the detection limit of elements as well as the minimum feature sizes of different phases that can be distinguished.

Jan 1, 2014