Search Documents

The Small Pebble Process for Reducing Ball and Power Consumption in Secondary Grinding Ball mills are used widely for secondary grinding. A mixture of ball sizes can be used to optimise grinding efficiency, but the use of balls smaller than about 30 mm in diameter is not normally viable, particularly when alloy steel is required. Preliminary testing of the grinding efficiency of various combinations of 40 mm steel balls and crushed stone in the size range 7 to 25 mm was carried out in a 300 mm diameter mill, which has accurate power measurement.The primary interest was to assess the potential benefit of adding small pebbles (from a primary circuit crusher or mill) to a secondary ball mill, to reduce ball consumption and to improve grinding efficiency. The optimum proportion of pebbles was found to be about 25 per cent by volume. This mixture produced about the same amount of fines as balls alone, but with lower power consumption, due to the lower density of the pebbles. The net result was a 12 per cent saving in power and a 25 per cent saving in ball consumption. The production of fines was partly due to pebble wear. The use of portions of 15 mm balls, (ceramic and steel), was also tested for comparison. A few batch pilot-scale tests were conducted in a 1.2 m diameter, 0.31 m long mill to test the viability of the pebbles at a larger scale. The pilot-scale tests confirmed the reduction in power and that the rate of production of fines was the same as that obtained with balls. The same residence time was used and this implies that pebbles can be added to an existing full-scale ball mill, with no loss in capacity. Samples of secondary mill feed and pebbles were obtained from a copper mine and the steady-state consumption of pebbles was determined by locked-cycle laboratory-scale tests. These tests demonstrated that mill power could be reduced by up 13 per cent and that the consumption of 40 mm balls could be reduced by up to 38 per cent, while maintaining the same throughput and product size. The rate of pebble addition was about 4 per cent of the primary circuit feed rate. Application has been made for patent protection.

Sep 13, 2010

By S J. Schafrik, C Keles, C Schlosser, E S. Gilliland, A K. Louk, N S. Ripepi, S Keim, J Amante, E Diminick

Three legacy coalbed methane production wells have been converted to injection wells for a one-year carbon dioxide (CO2) injection test to evaluate the potential for CO2 storage in the coal reservoir and the potential for enhanced gas production at offset wells. The injection reservoir is composed of 15–20 individual coal seams with an average thickness of 30 cm (1.0 ft), spanning a depth range of approximately 240 (800 ft) to 670 m (2200 ft).The monitoring program for this test includes gas and water sampling of the three injection wells, three dedicated monitoring wells and approximately 20 offset production wells. Key technologies used for monitoring the study area include time-lapse GPS and interferometric synthetic aperture radar (InSAR) acquisitions for surface deformation measurement, a 28-station buried passive microseismic monitoring array, real-time downhole pressure and temperature sensing and perfluorocarbon tracer fluids, which will be injected with the CO2 stream. The schedule for the monitoring program includes pre- (baseline), during- and post-injection data collection. This schedule will allow data to be analysed for time-lapse changes and trends, which are important for understanding the migration of gas and fluid phases in the reservoir – including CO2, methane, other hydrocarbons and water – and for observing the changing distributions of reservoir pressures and stresses.The results of the monitoring efforts for this study have implications for monitoring mining operations. The combined use of GPS and InSAR geospatial data to evaluate elevation changes across and beyond the study area may prove to be an accurate option for measuring surface deformation, including mining-induced subsidence, in unstable terrain. Long-term microseismic monitoring using high-sensitivity instruments has several applications in mining operations, including rock stability monitoring, production monitoring and miner location detection during emergencies. Tracer studies and short-term microseismic monitoring used to assess methane extraction can also be used to develop and optimise degasification systems for underground coalmines.CITATION:Gilliland, E S, Ripepi, N S, Schafrik, S J, Schlosser, C, Amante, J, Louk, A K, Diminick, E, Keim, S, Keles, C and Karmis, M, 2015. Monitoring design and data management for a multiwell CO2 storage/enhanced coalbed methane test in a stacked coal reservoir, Buchanan County, Virginia, USA, in Proceedings Third International Future Mining Conference, pp 47–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Butt C. R M

Resurgence in Au exploration during the past decade has been characterised by a considerable emphasis and dependence on geochemical procedures. This has been made possible, firstly, by marked improvements in analytical sensitivity over those previously available and secondly, of particular importance to exploration in Australia, by a better understanding of the distribution of Au in the regolith, which has led to the optimisation of sample media. These developments have given exploration companies the ability to seek and detect subtle and widespread geochemical signatures of concealed Au mineralisation and provided an enhanced capability to interpret the data. As a consequence, several new discoveries have been made, even in areas that have been intensively explored in the past. In the deeply weathered Yilgarn Craton (WA), and in equivalent areas elsewhere in Australia and overseas, Au has accumulated in the upper lateritic gravels and duricrusts of the regolith, probably during humid climatic periods in the Tertiary. The laterites may not only be Au ores in themselves, but research by CSIRO and CRC LEME has shown them to be very important sample media, (eg Anand and Smith, 1992). In many areas, however, the laterite has been eroded and hence is unavailable as a sample medium and chemical modification under more and conditions since the Tertiary has leached Au from the upper saprolite. This has greatly increased the difficulties of exploration, particularly where reliance was placed on sampling between 2 and 15 m of the surface. Further research, however, has demonstrated that, despite this leaching, recent remobilisation of An has caused it to concentrate in a specific soil component, pedogenic carbonate, usually in the top I - 2 m, thereby giving surface expression even to mineralisation that is concealed by over 20 in of leached overburden. Secondary carbonates, commonly referred to as calcrete, may precipitate as calcite and/or dolomite in regoliths where the average annual rainfall is less than about 600 mm. Pedogenic carbonates are those that form in unsaturated (vadose) soil horizons. They are widely distributed in the Gawler and Yilgarn Cratons. In the Yilgarn Craton south of about 30¦S ('the Menzies Line'), they are seemingly more abundant over more basic rocks and towards the south east (Figure 1). In contrast, groundwater calcretes form in saturated (phreatic) environments, typically in the axes of major drainages north of the Menzies Line. These are known to accumulate economically-significant grades of U but not, apparently, An.

Jan 1, 1997

By G R. Ballantyne, M S. Powell, M Tiang

This paper reviews the proportion of energy attributable to comminution within the Australian gold and copper mining sector. The need for this is motivated by inconsistencies in the quoted energy usage data and the lack of a common basis for reporting the fraction of energy in mining that is attributable to comminution. This study should form a reliable basis from which to assess both demand and opportunities to reduce energy consumption.The proportion of milling energy was calculated for the major producers in the Australian gold and copper sector. A sampling methodology created by Powell et al (2003 - 2010) was initially used to provide an accurate and meaningful measure of the energy used in the comminution process. However, no useful method for grouping similar mines was found. Fortunately, a surprisingly large amount of high quality data was found from a number of different sources, allowing the development of robust relationships to be used to estimate a high proportion of the unknown values. The fraction of energy attributable to comminution was found to be dependent on how the total energy consumption was defined. For instance, comminution accounted for 52 per cent of the electrical energy, but only 21 per cent of the total energy publicly reported by the mines because a substantial proportion of energy used on a mine is in the form of transportation fuel (mostly diesel). Critically, the measured electrical energy consumption does not account for transmission and generation losses, while diesel energy usage is typically quoted according to its calorific value. This review proposes that diesel should instead be converted via the mechanical efficiency factor for diesel engines. Using this conversion, comminution was found to account for 36 per cent of the available energy on average. This approach allows a useful basis of comparison for mines regardless of whether milling energy is obtained from electrical or diesel generation. A summary of the results are shown in Figure 7 with other values obtained from literature. The total comminution energy assessed in this study accounts for 1.3 per cent of AustraliaÆs electricity consumption, this figure will increase as the other mineral commodities are added to the study.CITATION:Ballantyne, G R, Powell, M S and Tiang, M, 2012. Proportion of energy attributable to comminution, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 25-30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Bacterial leaching of sulfide minerals are fairly well established in heap, dump and in situ leaching and the primary bacterial treatment of refractory gold concentrate using CSTR have gained industrial prominence in recent years. Three cultures, a mesophile T ferrooxidans (DSM583), a moderate thermophile Sulfobacillus acidophilus (strain YTF1) and a extreme thermophile (Sulfolobus strain BC65) were used for the biooxidation (pre-treatment) of the Porgera gold-bearing pyrite concentrate under optimum O2 and CO2 enriched air (30 per cent O2 and ten per cent CO2) based on volume ratios. The positive effect of using oxygen and carbon dioxide enriched air for the biooxidation of gold-bearing pyrite mineral was clearly demonstrated where an increase in Fe release rate by a factor of 2.8, 1.8 and 1.5 for DSM583, YTF1 and Sulfolobus respectively were observed compared with the shake flask tests. The lag phase observed with the other test conditions such as in shake flask or with air decreased by about 80 per cent for all three cultures. The average observed dissolved oxygen concentrations in the pulp for these tests were 8.7, 5.8 and 5.0 mg/L for DSM583, YTF1 and Sulfolobus respectively, indicating that O2 was not limiting in these tests. The pulp redox potential was observed to increase with time for all tests coincident with the leaching rate and reaching a maximum of 663 mV, however the maximum value differs for each strain, with DSM583 exhibiting the highest followed by YTF1 and Sulfolobus. Biooxidation of pyrite under optimum gas enrichment at different pulp densities showed near total Iron extraction occurred for pulp densities of three, ten and 20 per cent (w/v). At high pulp densities, more so at 40 per cent than 30 per cent (w/v), the leaching rate decreased rapidly for tests with YTF1 and Sulfolobus. Monitoring of dissolved O2 shows that O2 demand increased with increasing pulp density and the average dissolved O2 concentration observed for YTF1 and Sulfolobus at 40 per cent solids concentration was 1.0 mg/L and below, suggesting limiting oxygen and carbon dioxide conditions for these two cultures. The decrease in leaching rate observed at high pulp densities (30 and 40 per cent) under optimum gas enrichment was accompanied by low metal dissolution and low redox potential values which was attributed to shear stress due to attrition of cells by high solids concentration, toxicity of metal ions especially Ag and Fe and the formation of precipitates and jarosites as confirmed from XRD analysis of leach residues hence impeding the leaching process. Limiting conditions due to high pulp density and viscosity were only observed for YTF1 and Sulfolobus. The subsequent cyanide leaching for precious metals from the pre-treated pyrite concentrate in all cases shows the extent of gold and silver recovery increased with the degree of pyrite oxidation and Au and Ag recoveries in excess of 80 per cent were achieved compared with only 18.1 per cent and 35.9 per cent for gold and silver respectively when treated by direct cyanide leaching on the original, untreated concentrate.

Jan 1, 2004

By M H. Randell, J B. Haines

The Honeymoon Uranium Project comprises the Honeymoon Deposit,Goulds Dam Deposit and Yarramba Prospect in the Southern Lake Fromeregion, South Australia. Both the Yarramba Prospect and HoneymoonDeposit (which includes Honeymoon and East Kalkaroo orebodies) arelocated in the Yarramba Palaeovalley. The Goulds Dam Deposit is about75 km north west of Honeymoon, in the Billeroo Palaeovalley. Exploration for sediment-hosted uranium began in the area in the late1960s, culminating in the discovery of Honeymoon and Goulds Dam inthe early 1970s. In 1982, a 25 L/s demonstration plant was built atHoneymoon to confirm suitability for in situ leaching. The project was put on hold in 1983 due to changes in government policy. Southern Cross Resources Australia Pty Ltd acquired the project in mid 1997. Roll-front deposits form from a migrating geochemical cell, anadvancing reduction-oxidation interface between oxygenateduranium-bearing groundwater and its reduced aquifer host. The source of metal is uranium-anomalous granites, which were eroded fromsurrounding ranges. The weathered granites and resultant sediments are stripped of uranium by oxidised groundwaters, to form solutions carrying uranyl carbonate complexes. The solutions percolate down-slope through permeable sand zones until contacting a reduced environment where uranium precipitates. Uranium mineralisation occurs interstitially between and as thin coatings on sand grains, usually in the form of uraninite or coffinite. The palaeovalleys (previously termed palaeochannels) are incised intounderlying Cambrian/Precambrian basement rocks and filled withsemi-consolidated, largely un-cemented, Tertiary sediments of the Eyre Formation. The late Palaeocene to middle Eocene Eyre Formation is the basal unit of the Tertiary succession in the Callabonna Sub-basin of the Lake Eyre Basin. Further to the north, the Lake Eyre Basin overlies the Jurassic-Cretaceous Eromanga Basin, which comprises much of the Great Australian Basin. Eyre Formation sediments are in turn overlain by the late Tertiary Namba Formation and terrestrial Quaternary units. At Honeymoon, the Eyre Formation includes immature, pyritic,carbonaceous sands and gravels interbedded with lignite andkaolinite-illite-montmorillonite clays. It was deposited by braidedstreams during epeirogenic uplift of the Olary Ranges, accompanied bysubsidence of the Lake Eyre Basin. The Eyre Formation comprises aconsistent stratigraphy of interbedded sand and clay units that arecontinuous over the Honeymoon Deposit but with local variationindicating some hydrological connection between aquifers.In the Honeymoon orebody, uranium occurs within coarse-grained,pyritic sands where the basal sand pinches out between overlyingcarbonaceous clay and the southern palaeovalley slope. Its characteristics are typical of the well-developed, planar limb of a roll-front uranium deposit. Zonal changes related to the reduction-oxidation interfaces across the deposit are readily observable. The orebody extends for nearly 1000 m along the valley margin, is 400 m wide at its maximum and averages about 6 m in thickness. The East Kalkaroo orebody also lies near the southern margin of theYarramba Palaeovalley. It extends discontinuously for approximately 3.5 km and averages 200 m width, with significant uranium present in the Middle as well as the Basal Member. The Billeroo Palaeovalley extends northward for 40 km sub-parallel tothe western side of the Benagerie Ridge, is up to 5 km wide and hasgently dipping banks. Eyre Formation within the palaeovalley isconcealed beneath 90 m of Quaternary and Namba cover, isapproximately 40 m thick, and is sub-divided into three upward-finingunits, which are remarkably similar to the Yarramba Palaeovalleysequence.

Jan 1, 2001

Supplement to Proceedings Number 120, December, 1940. Drawings accompanying paper by T M Carey 'The Surface Plant at the Zinc Corporation Mine, Broken Hill'

Jan 1, 1940

The Kennedy Siltstone Open Cut provides graded rock for stope filling. Rotary drilling of 310 mm blastholes with a Gardner Denver GD120 is used, and the successful application of an equilateral triangular drilling pattern is described. Charging practices and the development of bulk slurry handling are outlined. Blast monitoring plays an important role in K.S.O.C. drilling and blasting operations. The proximity of nearby residential areas (1300 m) and the Mount Isa Airport (4500 m) necessitates special attention with regard to the minimisation of both air blast and ground vibration levels. The application and control of drilling and blasting parameters has had a direct bear- ing on success of the mining operations and also played an important role in reducing the disturbance to the community.

Jan 1, 1978

This paper discusses the recently com- pleted TBM-driven pressure tunnel at the Sand Bar Hydroelectric Power Project. The Sand Bar Project is a diversion scheme situated on the middle fork of the Stanislaus River in the Western Sierra Nevada, California, U.S.A. As part of the project, a 5.6 km long and 3.71 m diameter unlined pressure tunnel was bored by a Jarva TBM at the average rate of .37.5 m/ day. This report deals with construction aspects of the tunnel, including TBM performance, lining design, and remedial support measures. Correlations between TBM performance, geologic conditions, and rock properities are made, and the Contractor's mode of operations are discussed. Advance rate prediction, and the impact of these excellent advance rates attainable in hard rock using the new machines are discussed.

Jan 1, 1987

By O. J. RICHARDS

The Wongawilli system of mining has been in use for over 30 years and has enabled high production rates and acceptable extraction ratios to be achieved in seams less than 4 m in thickness. A modification of the Wongawilli system has been developed to permit the use of a continuous miner and mobile equipment to extract a coal seam 6 m thick. Following physical and mathematical model studies the new mining method is now undergoing field trials at Collinsville, Queensland. Progress of the field trials to date has achieved 99% extraction of the upper slice by remote control operation of the continuous miner and established the feasibility of installing resin grouted wooden dowels in the coal floor to reinforce the coal septum. The method is explained in the text.

Jan 1, 1980

By Clark G

The latest addition to the grinding circuit at Bougainville Copper Limited is another 5.5m by 7.3m primary mill (No.13). The mill can operate in a primary or secondary mode. Its distinguishing feature is its capability for speed variation, by means of a cycloconverter-fed synchronous ring motor. The engineering and metallurgical reasons for selecting such a drive system are described together with aspects of the installation and commissioning. Results of investigations into the relationship between mill speed and grinding efficiency are presented. It is concluded that mill speed variation within the range 70 to 80% of critical speed has very little effect on grinding performance. Beyond this range, grinding performance deteriorates. The same conclusions were reached when mill speed was varied at reduced ball charge levels.

Jan 1, 1986

By Terlich R. E, Finlayson J. M

A combination of high virgin rock temperatures, deep workings and extensive utilisation of heavy diesel equipment has presented North Mine (A Division of North Broken Hill Limited) with challenging ventilation problems. These problems have been addressed in a variety of ways which include in the order of 6000 kM of underground refrigeration. The future of North Mine depends on the successful development and extraction of ore in excess of 1100 m below the shaft collar using mechanised cut and fill mining. The success of this will depend on the installation of a complex chilled water reticulation circuit in this area. This will involve planning and constriction of a number of large dams, installation of pups and turbines, and the successful commissioning of several large water to air heat exchangers.

Jan 1, 1988

By Siemon J. R

It is possible to use compacted anodes formed at low pressure for the direct electrowinning of lead from sulphide concentrates. An anode containing 5.5 per cent graphite, formed into a compact at 34 MN m-2, enables lead to be won at a current efficiency of about 80 per cent; the power consumption .at 150 A m-2 current density being 0.4 kWh per kg lead. It would be necessary to use diaphragm cells to obtain a sufficiently pure product. A conceptual design for a full-scale plant is presented, together with a cost estimate for the production of lead by a process based on direct electrolysis of compacted concentrates. It is unlikely that the proposed process will be economically competitive with the conventional lead smelting.

Jan 1, 1976

By M Donghi, G Ramage, A Barnes

As the mining landscape continues to transform, the challenge of accessing deeper orebodies quickly and safely is becoming a frequent topic of conversation amongst those in the mining industry. The rapid development of underground mine entries to gain earlier access to deeper orebodies is an ever-present challenge to mine owners and contractors. Overcoming this and providing economical solutions to unlock the value in these deeper deposits is a challenge that should be confronted.In 2013, Redpath Australia Pty Ltd (Redpath) commenced construction of what would be the first of two drifts excavated through the use of a tunnel boring machine (TBM) in Queensland’s Bowen Basin.The excavation and development of the two drifts (declines) was completed as part of a contract for underground mining services between Redpath and Anglo American at the Grosvenor Coal Mine Project in Central Queensland, located approximately 5 km north of the town of Moranbah. Having recently completed the drift development, this paper will extend on the early writings of Donnelly, Ramage and Donghi (2014) and provide detail on the operational achievements, advance rates, threats, opportunities and learnings during the excavation of the two declines: the conveyor (CV) drift and the transport (M&M) drift.CITATION:Ramage, G, Donghi, M and Barnes, A, 2016. Experiences gained through tunnel boring machine decline development, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 695–712 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By G Akdogan, R V. R Handfield-Jones

The application of microwave energy as a substitute for conventional heating has drawn interest from many researchers in extractive metallurgy. Microwaves have a heating effect just as many other forms of radiant energy. Microwaves are able to penetrate the substance at which they are directed and in being absorbed heat the material from the inside. As a result of heat generated in the interior of a particle, microwaves can affect the rupture of a particle (in this case a host ore) and break down the matrix of the particle (host ore) and expose the recoverable mineral to the leaching reagent. Two series of leaching experiments were carried out at temperatures above 90????C using a conventional heater (hot plate) and a modified 850 W, 2.45 Ghz microwave oven. One series of tests was carried out at ambient temperature. A pyritic/arsenopyritic gold concentrate was leached with 3.3 kg/t to 6.8 kg/t NaCN for two hours. The extraction of gold at 6.8 kg/t NaCN was higher in microwave assisted leaching (59 per cent) than the extraction obtained in leaching at conventional heating (39 per cent) and ambient temperature (28 per cent). Extraction of gold was dependent on the size fraction used and was 48 per cent for û75 ¦m, 43 per cent for û90+75 ¦m and 37 per cent for û150 + 90 ¦m size ranges.

Jan 1, 2000

By M Dean, M Nehring, P Knights, M S. Kizil

Integrated continuous mining techniques such as fully mobile in-pit crusher and conveyor (FMIPCC) systems offer inherent labour, energy and environmental benefits to deep pit metalliferous mines. However, before such systems become commonplace, a number of barriers must be overcome.This paper outlines a number of commonly perceived barriers to FMIPCC application, together with a number of suggested solutions. The paper advances a design approach for specifying FMIPCC systems for deep pit metalliferous applications. A novel FMIPCC configuration is advanced using a hydraulic excavator in backhoe configuration. Because of the requirement to minimise belt extensions, a mine planning approach is presented based on a series of parallel and radial belt conveyor moves.The FMIPCC system does not fully replace truck-shovel systems. In the proposed mine plan, sinking is undertaken with truck-shovel systems using a series of box cuts, whereas pit ‘widening’ activities are accomplished via the FMIPCC system. Because of inherent differences in mine sequencing, the net present value derived from the FMIPCC mine will differ markedly from that derived from traditional, nested-pit, truck-shovel mining approaches. Therefore, any comparison of the FMIPCC and truck-shovel approaches must take into account radically different mine planning approaches.CITATION:Dean, M, Knights, P, Kizil, M S and Nehring, M, 2015. Selection and planning of fully mobile in-pit crusher and conveyor systems for deep open pit metalliferous applications, in Proceedings Third International Future Mining Conference, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Mikula PA

This paper presents the results of in-situ and laboratory investigations into a mining method which utilises conventional continuous mining techniques to carry out two passes in thick coal seams, resulting in the development of stable pillars with relatively small width dimensions and heights up to 6 m. Geotechnical investigations included structural mapping, brightness logging and standard laboratory testing. Virgin stress was measured using overcoring techniques. Two approaches to pillar design were used in the study. These were; pillar design based on empirical formulae and laboratory testing, and pillar disign using calibrated mathematical models. A trial panel was developed at 300 m depth to study pillar deformation and stress changes due to mining. The extent of rib deformation was studied using borescopes and extensometers. In-situ geotechnical measurements were used to calibrate displacement discontinuity and finite element mathematical models of the coal seam. These models were then used to predict the behaviour of a small panel of pillars which were to be developed to 6 m height. The mining method was shown to be feasible provided adequate rib support was installed. The benefit of rib support was found to be two-fold, in that it increased confinement of the pillar in zones of low horizontal stress, while reducing horizontal stress relaxation in zones of high horizontal virgin stress. The possiblity of roof control by designing the small pillars to yield on retreat is discussed.

Jan 1, 1986

By Kuzmitch O, Morozov A

The main direction in the mechanisation in the mines of the Donbas and the USSR is long-face technology with complexes on the base of hydraulic supports. On the base of the 30 year old experience of exploitation of the coal clearing systems the serious data about the behaviour of the contained rock, display of underground pressure 'on longwalls and preparatory workings have been accumulated. Exploitation works in mines of the USSR are carried out at different depths: from 1000m to 1200m. There are 26 mines in Donbas, which exceed the depth of 1000m. It is the mines of Donbas, where is a rich experience of the exploitation of coal seams in various conditions. Besides, there are wide variations on the factors of the extraction thickness, depth of seam, angle of dip, occurrence of gas dynamics and others. In many scientific establishments, and in Donetsk Polytechnical Institute also, there are scientific research/results, which can be of interest for the coal mining countries.The volume of coal mining from longwall system-mechanised walls in Donbas became stable at the end of the 70s at level of 70 percent. All the efforts to increase this level have not given any notable results, not saying about the technical-economical data, which gradually deteriorate. It shows that positive progress in using the technology for the long walls is over and it is necessary to find new ways of mechanisation of coal winning.

Jan 1, 1991

By S M. Aminossadati, C M. Stewart, M S. Kizil

Mine ventilation models are now an accepted component of most mine management systems. However, modern ventilation models also represent a highly structured spatial data source, defining underground pathways and connections across a mine. This creates opportunities to extend the use of network models beyond ventilation design, by using critical path algorithms to find pathways such as minimum distance or minimum time.This paper explores the use of ventilation network models to automatically analyse and calculate potential emergency escape routes. A variation of Dijkstra’s algorithm is used to predict complex pathways between any two points across a model, representing an escape route from an emergency area (such as a fire) to a safe location (such as the surface or a refuge station). Weighting can be assigned to paths to represent potential travel speed, obstructions or preferred routes. Finally, emergency considerations such as smoke or gas in some parts of the mine can then be incorporated into the pathways to force the algorithm to avoid dangerous routes and specify safer pathways. Ventsim is used to visually show example results.Emergency egress pathway prediction using ventilation network models can provide an efficient way to quickly predict the quickest or most efficient escape routes for emergencies or planning purposes.CITATION:Stewart, C M, Aminossadati, S M and Kizil, M S, 2017. Emergency egress pathway prediction using ventilation models, in Proceedings Australian Mine Vent Conference 2017, pp 57–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

One of the most frequently asked questions at the feasibility study stage of a project is, æhow big can one go?Æ This important question effects costing and efficiency of metallurgical equipment, the real estate required and the operating plant strategy.The presentation covers both engineering and process considerations and explains the limits that exist today and explores future trends.The paper is specific about large slurry application usually found in gold applications; however, it could apply to silver and uranium or other dense media leach duties.Agitator drive sizes are examined as well as process risks associated with large tank agitation. New technology has increased the maximum tank size and designers are now experienced in tank volumes in excess of 5000 m3. Tanks of 6000 m3 have been agitated and 10 000 m3 tanks are within present engineering know-how and scale-up.Fabrication techniques for shaft and impeller designs exceed the existing standards and new specifications will be needed to cover large mixer design. The paper covers certain aspects of mechanical design and proposes alternative standards that are more appropriate. Process considerations such as fluid natural frequency as well as typical superficial velocities for efficient operations are examined. Scale-up techniques based on existing and new technology are also examined to ensure a successful installation.The presentation therefore covers the majority of large mixer design questions that are frequently asked.

Jan 1, 2006