Search Documents

The Bradford Process, Australian Patent No. 11253, has had considerable application in the treatment plants of Broken Hill mining companies, and is at present being used by the North Broken Hill Limited for the treatment of weathered slime accumulations.The "Mining and Scientific Press," of 28th September, 1918, describes the Bradford Process at Broken Hill, specially featuring its application to slime material at the Proprietary mine-the home of the process.The points then stressed for galena flotation were acidulated slime pulp (0.025 to 0.030% H2S04) at temperature 85° to 90° F. and suitable time contact, with 1.5 to 2 lb. of sodium hyposulphite (per ton on slime) to permit the released S02 to "wet" or depressthe blende mineral. Also 1.0 to 1.3 lb. of crude sulphur (per ton on slime) was burnt, to supply S02 for keeping the lead concentrate clean during flotation. Pulp density varied from 23 to 26% solids. Since 1918 the process has been simplified in its application.Acidity of circuit, temperature, and sodium hyposulphite have been dispensed with, and now the S02 is practically all obtained by burning crude sulphur. I The plant units now employed for control and absorption of S02 gas constitute the main advance made in process, and these, with other details, are fully explained in this paper.APPLICATION AT BROKEN HILL NORTHThe existing North Broken Hill Limited gravity mill commenced operations on 9th September, 1909.

Jan 1, 1929

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990

By C J. Noack, P B. Ganza

The concept of large trucks underground has been around for some time. While the road train concept is gaining momentum, there are underground mining applications where these trucks have not been suitable. Unfortunately few of the ægreenfieldsÆ projects that are most suited to the road train concept have come æon lineÆ since the underground road train was first introduced to Australia in 2001 so that the trucks have generally been adapted to existing operations. As at December 2004, there were 17 road trains operating underground in Australia, one being rebuilt and one under construction. This paper addresses the necessity for the mining industry to have an integrated ore transport system that starts at the underground load haul dump unit (LHD) in the stope production area and finishes at the crusher feed at the processing plant. Chute and orepass designs are investigated, as well as feeders to determine the best load and haul system for large-scale trucking. The paper also discusses potential developments in the large truck scene. The paper highlights the cost and productivity gains by introducing large trucks and associated integrated ore transport systems underground. While 400 vertical metres was seen as the limit of vertical hauling in the 1970s, one kilometre is a common discussion point for trucking limits today. In real terms the cost of underground trucking (including ownership costs) has decreased from $1.50 - $2.00/t.km in the mid-1990s to $1.00 - $1.20/t.km at present.

Jan 1, 2005

By Johns AS

Comissioning of a new residue disposal tcluding upgraded classification for none backfill preparation, new variable speed pumps and a new residue dam took place in 1¦76. The system is described.

Jan 1, 1978

The rush for alternate iron-units in the last few years spurred a true outbreak of new alternate iron units projects many of them incorporating new process in what can be classified as the.most fruitful and innovative technology outburst, in the steel industry, in decades In a recent paper we focused on what would be, in our opinion, the ultimate targets of the use of alternate iron-units by mini-mills: 1. to improve quality, 2. to reduce cost, 3. to increase plant productivity, and 4. to improve `supplyability'. With these objectives in mind liquid hot-metal, among all possible scrap substitutes, has been proven to be by far the best. This conclusion stems from many different authors who have reviewed the `value in use' of hot-metal against other alternate iron units and measured its impact on steel-shop productivity and cost (Figure 1).

Jan 1, 1999

By M J. Begbie, K B. Sporle

The Golden Cross low sulfidation epithermal deposit produced approximately 750,000 ounces of Au from two ore zones: the underground Empire Vein System and the open pit stockwork. The Empire Vein System has at least eight stages of vein formation: (1) sulfide veins, (2) black veins, (3) massive veins, (4) banded veins, (5) thin white veins, (6) crumbly veins, (7) massive/platy calcite veins, and (8) flattened rhomb calcite veins. Gold mineralisation occurred relatively early in the lifetime of the system, dominantly during 2 through 4. The late calcite veins (7 and 8) and early sulfide veins (1) are barren. The vein system formed in a dominantly extensional environment, though some compressional faulting may have also existed during vein formation. There is no evidence for significant strike-slip faulting during vein formation, highlighting the fact that explorationists should pursue on-site structural patterns rather than fashionable models.

Jan 1, 1998

The N3500 orebody is the northern continuation of the 3500 orebody at Xstrata Copper's Enterprise Mine and occurs at a depth of 1.3 to 1.8 km. At the nearby S3500 orebody, extreme deformation was observed in access drives where there was a high number of bedding planes per metre combined with either graphite or talc infill. The observed failure mechanism was largely controlled by the geometry of the inclined bedding submitted to high horizontal stresses. Due to the anisotropic strength and deformation behaviour of the shale rock mass, traditional isotropic methods of geomechanical property estimation based upon GSI are not appropriate. A numerical modelling approach, based upon the distinct element codes UDEC (2D) and 3DEC (3D), has been developed to accurately simulate the failure mechanisms and deformation observed in the initial infrastructure surrounding the N3500 orebody.

Nov 25, 2010

By Gray J, Krouse HR, Changkakoti A, Kwak TAP

The Dachang tin field with more than one hundred million tonnes of ore at 1% tin and 3% Zn is one of the largest tin fields in the world. It comprises five carbonate replacement tin deposits, of which the Changpo deposit containing about 80 million tonnes of ore at about 1% tin is the largest deposit. The deposit, hosted by middle Devonian limestone, argillaceous limestone and black shale, is genetically related to the Longxianggei granite.The oxygen, hydrogen and carbon isotope data of minerals, rocks and fluids suggest a magmatic fluid which evolved during the crystallization of the Longxianggei granite. Mass balance calculations show that the depletions observed in 180 and 13C values of calcites from the ore bodies to the country rocks were due to continous isotopic exchange reactions between the magmatic fluid and the marine limestones at different W/R ratios and between 300 and 600¦C.

Jan 1, 1990

The Mt Todd Project is located 42 km northwest of Katherine in the Northern Territory. The identified mineral resource estimate for the Batman gold deposit is 66.7 million tonnes (Mt) grading 1.4 grams/tonne (g/t). Proved and Probable Ore Reserves total 42.3 Mt grading 1.5 g/t. Orebody definition and reserve estimation is based on extensive percussion and diamond drilling. Exhaustive bias analysis comparing grades produced from different drilling techniques has been undertaken. Similarly, detailed check assaying programs have been run to validate grade data produced by commercial laboratories used during the exploratory drilling phase. Significant biases were established from both studies and appropriate 'corrections' were made to drillhole databases prior to final resource and reserve estimation. 3D geostatistical modelling has been utilised for resource and reserve estimation, with specialist consultants contracted for this work. At all times, interpreted geological controls on mineralisation, provided by

Jan 1, 1994

By M Grinceri

The New MetroRail City Project was completed in 2007 in Perth, Western Australia. The project included construction of two underground stations, twin bored rail tunnels of 1.4 km combined length and cut-and- cover tunnels and dive structures of about 1 km total length. It is the first major underground construction project within the Perth central business district (CBD). This paper provides an introduction to the project and describes the geology and hydrogeology of the area. Ground conditions varied significantly along the alignment from soft estuarine muds in an area of reclamation to very dense cemented sands and very stiff to hard clays. Deep foundations for the project extend down into the bedrock below the CBD, a Tertiary siltstone/sandstone. Key geotechnical hazards encountered during the project are discussed. The building protection methodology on the project is described, including damage assessment, condition surveys, monitoring and protection of key structures.

Jan 1, 2008

Taxation is a major factor in evaluating mining project developments. The availability or otherwise of effective tax relief for project expenditures can have a crucial bearing on the decision to proceed with a project. The special position of the mining industry is recognised within the Income Tax Assessment Act (the "Tax Act") by special legislation, namely Divisions 10, 1OAAA and 10AA. The legislation both extends the scope of items which are eligible for deduction and affects the timing of deductions. Generally, the legislation separates expenditure into 3 categories: 1. Expenditure on exploration 2. Capital expenditure on the development and the running of the mine; and 3. Facilities used in the transport of minerals. Companies evaluating a project should carefully analyse their proposed expenditures, allocating them between these categories so as to identify potentially non-deductible expenditures and to determine the period over which tax relief will be Obtained.

Jan 1, 1983

By Boyes B. A, Haydon D. J

The Paddington project is a gold mining and processing operation located 35 km north of Kalgoorlie in the Eastern Goldfields region of Western Australia (Figure 1). The project, which is operated by Pancontinental Goldmining Areas Pty Ltd, treats 1.25 Mtpa of oxidised gold ore, derived mainly from open cuts adjacent to the plant, with minor tonnages from other pits in the region treated on a custom-milling basis. Gold is recovered using a conventional CIL process. The process raw water supply of 3 500 kUd is derived from the local groundwater system. Average salinity of the raw water is around 90 000 - 100 000 mg/L total dissolved solids. A small portion of the raw water is passed through a vacuum distillation desalination plant to produce the project's 200 kUd requirement for high quality water for potable use and gold recovery.

Jan 1, 1988

By A Murphy, I Samsonova, N Eastwood, D Whittle

Part XI of the United Nations Convention on the Law of the Sea (UNCLOS or the Convention) (United Nations (UN) Division for Ocean Affairs and the Law of the Sea, 1982) establishes a comprehensive regulatory framework for the conduct of deep seabed mining (DSM) activities of mineral resources in the Area (defined in Article 1(1) of UNCLOS as ‘the seabed and ocean floor and subsoil thereof, beyond the limits of national jurisdiction’). Under that framework, DSM activities can only take place in the Area pursuant to an approved Plan of Work in the form of a contract with the International Seabed Authority (ISA) (the Authority), a 168-member international body created under UNCLOS to administer the Area. Private contractors can undertake DSM activities if they are sponsored by Member States of UNCLOS, providing a dual system of international and domestic regulatory control and oversight for activities in the Area.

Sep 1, 2024

o Resource production is essential for society. o Demand for resources will increase as population grows.o Resource industries are the main consumer of trained geologists.o The lead time from(1) training to productivity(2) research to resource production is measured in years.o An adequate supply of well trained geologists and successful geological research is an important agent in ensuring cost effective, adequate supply of mineral resources for society. Therefore the main beneficiary of geological education is society itself.o Society is paradoxically apathetic or antagonistic to the resource industry because (1) it represents change(2) lobby groups working for other causes have successfully moulded a bogey man image for the resource industry in the public eye.Professional training and research for resource industries consequently lack popular support. Funding is at an absurdly low level in comparison with the economic importance of resource supply.

Jan 1, 1990

In 1961, West Australian Petroleum's Eneabba No. 1 bore encountered 22 seams of coal totalling 40 ft in thickness between the depths of 6373 ft and 6441 ft. On analysis, this coal had a similar calorific value (8000-HOOO B.T.U./lb, assuming 20 per cent water) to the coal from the Collie Coalfield, Western Australia's only known area of commercially exploitable coal. Being buried to depths in excess of 6000 ft, the coal at Eneabba had developed weakly-coking properties, and thus, although much younger than the Permian coals of Collie, gave promise of being a major potential source of power for Western Australia.West Australian Petroleum undertook a programme of stratigraphic drilling and shallow test drilling to determine whether this coalhorizon persisted into the outcrop of the Lower Jurassic sediments in the Hill River district, 140 miles NNW. of Perth, and, if it was present, if the quality and quantity of the coal would warrant development of the deposits by open cutting. The coal horizon was identified in the near surface, but the poor quality of the coal and the complexity of the structure made development (in the area examined) uneconomic at the time.A strong seismic reflection in the Eneabba area occurs at the same depth as the Jurassic coals. This event originates within the upper beds of the Lower Jurassic and it is probable that the velocity contrast between the higher velocity siltstones and the very low velocity coals enhances this very strong, distinctive seismic reflection.This event can be followed on continuous seismic data over a large area of the northern Perth Basin, from 13 miles SE. of Dongara to 20 miles SW. of Coorow. It can be followed from a depth of 4000 ftnear Dongara to over 17,000 ft to the SE., so development of thisvast potential source of power will depend on the economics ofprocesses being developed for the production of power from theburning of coal seams in situ.INTRODUCTIONThe discovery of 22 seams of economically useable coaltotalling 40 ft in thickness in the Lower J urassic sedimentsof the Eneabba No. 1 bore (Fig. 1) led to the search forthese seams at economically workable depths. The Ministerfor Mines in Western Australia granted to West Australian1. Supervising Geologist, West Australian Petroleum Pty. Ltd.Manuscript received at The Institute, 25th May, 1964. and presented to the 1964Annual Conference.

Jan 1, 1964

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

This investigation was planned to determine:1. The precipitation-hardening properties of the copper-nickel-phosphorus alloys; and2. The influence of arsenic and bismuth, singly and together, on the mechanical properties of these alloys.It was carried out in conjunction with an investigation, previously published in these Prooeedings on "The Influence of Various Elements on the Mechanical Properties of Copper containing a small percentage of Bismuth," and also formed part of a study of the influence of bismuth, nickel and phosphorus on the properties of commercial arsenical-copper.The first part of the present investigation arose out of a discovery some years ago of precipitation-hardening in phosphorus-deoxidized coppernickel boiler tubes, containing approximately 2% nickel and 0·03% phosphorus, supplied to an Australian Railways Department. At that time there was little information available on precipitation-hardening in copperrich copper-nickel-phosphorus alloys, but at the end of 1935 a short paper on the subject was published by E. C. Rollason and T. G. Bamford(2) and at the beginning of 1940 a comprehensive account was published by D. K. Crampton, H. L. Burghoff and J. T. Stacy.(3) Although the investigation carried, out independently by the present author was not as comprehensive as that of Crampton, Burghoff and Stacy, the results are in agreement with those of the American as well as of the British authors; hence, only a summary of this aspect of the work is needed here to establish a basis for a study of the influence of bismuth and arsenic.PREPARATION OF TEST PIECESAll alloys were melted under charcoal in plumbago crucibles in an oil-fired furnace and were poured out of contact with air into oil-dressed moulds to give billets either 7· 5 in. long X 0.83 in. diam. X 1·3 lb. weight or 12 in. long X 1·125 in. diam. X 3·3 lb. weight depending on requirements (the larger size was used, for example, in establishing the annealing characteristics of the precipitation-hardening alloys). The raw materials were electrolytic copper of the composition described in the previous paper(I) 6% copper-arsenic, 14% copper-phosphorus, 1:7% copper-bismuth, and Mond nickel in the form of "shot." The method of producing test pieces from these billets and the annealing treatments ana tests to which the pieces were subjected have been described in the previous paper.

Jan 1, 1944

By L Soebari, W Sunyoto

The Wabu Ridge Gold Skarn deposit is located at elevations of up to 3100 metres above sea level, in the Central Highlands of Irian Jaya, Indonesia, 35 km NNW of the Grasberg porphyry deposit. Wabu is a grass-roots discovery in an area with no previous gold mining history or record of gold mineralisation. A geological resource of 117.26 million tonnes at an average grade of 2.16 g/t Au (1.0 g/t Au cut-off) has been defined to-date. Mineralisation is hosted within a skarn occurring along the southern boundaries of the Late-Miocene age monzonite-diorite Pagane intrusive complex. The intrusive complex occurs in the footwall of a major EW structure, the Derewo fault, which displays sinistral strike-slip and reverse fault movement. The Derewo fault separates Derewo metamorphic units to the north from platform sediments of the Australian craton to the south. The skarn has a strike length of 6 km and is up to 1.5 km wide. It is developed within calcareous shelf sediments of the Tertiary New Guinea limestone group and is dominated by prograde garnet development. Gold mineralisation was deposited during retrograde alteration and is directly associated with arsenophyrite and bismuth minerals. Retrograde alteration is distinguished by a sequence of clinopyroxene , magnetite, epidote and hornblende, biotite and chlorite and lastly carbonate. Gold is associated with the biotite/ chlorite phase together with sulphides and precipitated as the result of fluid mixing. The Wabu Ridge Gold Skarn deposit was identified in April 1990 during a regional program of helicopter assisted stream sediment sampling of -80 mesh (180 microns) fraction and panned concentrate sampling. The initial discovery sample site was situated 15 km down stream from the deposit and returned 1.49 ppm Au for the stream sediment sample and 138 ppm Au for the panned concentrate sample. A regional airborne helicopter magnetics survey, conducted in early-1992, helped defined the main magnetite associated skarn zone and the extent of associated igneous rocks. Detailed follow-up commenced in May 1992 and consisted of detailed mapping, soil sampling and ground magnetics prior to drilling the first hole in October 1992. Drilling to-date has delineated a contained geologic resource of 8.1 million ounces of gold and potential exists for a larger resource.

Jan 1, 1999

Fire-clay blocks lining the combustion chambers of zinc concentrate flash-roasting, furnaces operating at 1,000-1,200° C. have suffered moderately rapid deterioration due to slagging. The attack is accentuated by high temperatures, and is probably caused by lead oxide volatilized from the roasted concentrate.Resistance of refractories to attack increased with increasing alumina content from 30 to 45 per. cent but at 90 per cent alumina spalling was troublesome. Magnesite bricks were'subject to some spalling, but some types may lie satisfactory. Chrome and chrome-magnesite bricks spalled seriously.Material thought to be suitable for use as a monolithic lining slagged badly and an alternative may be tested.INTRODUCTIONThe Electrolytic Zinc Company of Australasia Ltd. uses two multi-hearth furnaces and four flash or suspension roasting furnaces for the roasting .of zinc concentrates at its Risdon Works. The hearth roasting plant has been described previously by Forster (1949).A brief descriptioI1 of the first three flash roasters was given by Gordon and Forster (1955). A fourth flash roasting furnace began operation early in 1957. This furnace is somewhat larger than the earlier furnaces, and the designed capacity is also higher, auxiliary equipment being altered to suit. An important structural difference between the older furnaces and the fourth flash roaster is that the walls of the combustion chamber of the new furnace are lined with high alumina fire-bricks instead of fire-clay blocks. Thischange was made because the fire-clay blocks in the older flash roasters had shown s-evere wastage due to slagging by lead derived from the concentrate.

Jan 1, 1959

The Heavy Media Separation plant operated at Lidsdale siding, eight miles from Lithgow, by the N.S.W. Mining Co. is a product of the Western Machinery Company, of D.S.A.This mill, designed to use finely ground magnetite as the heavy medium, was prefabricated in America and shipped to Australia for erection.First operated early in December, 1951 it has worked on a two-shift basis since. Designed for an input rate of 330 tons per hour, this mill is capable of washing 4 in. x /u in. coal down to its inherent ash by removing all heavy material, including high-ash coal.The principle is quite simple. A stream of raw coal is fed into the separatory vessel which contains a liquid medium, the density of which is adjusted to produce the desired split between coal and refuse. In this bath the lightest coal floats, and all material heavier than the specific gravity of the medium sinks, and is removed separately. Such a system is,. ideally suited to Western coal, as there is no definite splitting point between coal and refuse. Inherent ash of the coal fed to the plant ranges from 8 to 25%, the corresponding density range being from 1.28 up to 1.8.Generally speaking, the higher the density the higher the ash content of the coal.The density in the separatory vessel (hereafter called the cone) can be quickly and easily adjusted throughout the above range to any desired value. Customer requirements, coupled with the economics of washing, dictate the proper specific gravity to be maintained. At present this is held at 1.52...

Jan 1, 1954