Search Documents

By C. Edwin Nighman

THE following is a description of the methods used in rescuing men and extinguishing the underground fire at the Pennsylvania mine, Butte, Mont. This fire, which cost the lives of 21 men, began about 9 p.m., Feb. 14, 1916, at or near a ventilating fan on the 1,200 air-shaft station. This shaft at that time was downcast, while the main hoisting shaft was upcast. Owing to the proximity of the fire to the air shaft, the air in the latter soon became heated, and as the fan on the level was not running¬the power having been cut off shortly after the outbreak' of the fire-the aim' shaft became upcast to the 300 level. At this point a blanket of cold air from the surface caused the smoke and gases to he drawn in on that level and carried down again through the workings to the 1,200. A short time after the discovery of the fire, water was turned down the air shaft through a series of pipes around the collar of the shaft, which caused the smoke to recede, below the 300, so that within 2 hr. it was possible to search that level for the missing men. From the above it will be apparent why the air shaft was upcast instead of downcast as under normal conditions, and why men were suffocated at considerable distances from the seat of the fire. The smoke and gases that came up the main hoisting shaft did not diffuse through the workings to any extent. There are doors on all levels in the connections to the main hoisting and air shafts, but-in the confusion and running around many of these doors were left open, and this undoubtedly caused the smoke and gases to spread more rapidly than they would otherwise have done. It was necessary for most of the men on the various levels to pass close to the air shaft in going to the hoisting shaft, and when they encountered the smoke and gases in that vicinity a number turned hack and climbed down with the direction of the air currents and were then suffocated, while all those who passed through the relatively short pall of smoke to the main shaft were saved.

Jan 2, 1917

By Jerome Alexander

It is an outstanding fact of Nature that many of the practical properties of substances are dependent, not on their ultimate chemical composition, but on the kind and degree of aggregation of their constituent particles. Thus, a granite boulder is unmoved by wind or water, but if reduced to a fine dust it will be blown about by the wind and washed away by the rain. Carbon in one crystalline state of aggregation (diamond) is the hardest known substance, whereas in another crystalline state (graphite) it is so soft that it is used as a lubricant. Laying too much stress on the mere chemical analysis of substances is apt to obscure the fact that the nature of the aggregation of their particles is always a factor of importance, and sometimes the most important factor. Colloid chemistry deals with matter in a very fine state of subdivision; its sphere begins with particles just a little smaller than a wave length of light and extends down until they blend into molecular dimensions. With particles of this size, such phenomena as surface tension and adsorption, which depend on the development of free surface, become enormously magnified. Thus a cube of 1 cm. edge has a surface of only 6 sq. cm.; but if it is reduced to colloidal dimensions by being cut up into cubes each having an edge of 0.01 µ (0.00003 mm.), it will yield one million, million, million (1,000,000,000,000,000,O~) such cubes, having a combined area of 600 sq. m., or 21,274 sq. ft. The tiny force with which a drop of rain clings to the window pane becomes a factor to be reckoned with, if the surface involved is increased millions of times. From the colloid-chemical viewpoint, metals and alloys may be regarded as jellies or sponge-like structures,. the viscosity or stiffness of which at ordinary temperatures is exceedingly great; and like all jellies their properties are dependent on the composition and degree of dispersion of their constituent phases. These, in turn, depend on chemical composition, mutual solubility, speed of chilling, subsequent mechanical and heat treatment, etc. In fact, in preparing metals and alloys for practical use, we remove undesirable constituents (as in the conversion of pig iron into steel), add desirable constituents (as in

Jan 1, 1919

By F. E. Bash

Previous to the war, this country depended on Europe for its supply of a number of alloys of great importance in the manufacture of electrical apparatus and equipment. When this source was cut off shortly after the beginning of hostilities and the small stocks in the United States were exhausted, either inferior substitutes had to be used or the manufacture of the apparatus suspended. Since electrical equipment was of primary importance in the prosecution of the war, the substitutes had to be used until the composition and processes of manufacture of the alloys could be determined. Included among these alloys was one generally known as manganin, which is composed chiefly of copper and manganese and which, beside having a low-temperature coefficient of resistance, has a low thermal electromotive force against copper. These qualities make it valuable for the manufacture of electrical instruments and machines in which it is used in the shape of wire, rod, and strip. As a result of these circumstances, an investigation was started to determine how manganin could be made on a commercial basis so that a product of uniform quality and the necessary electrical characteristics could be produced. The object was to procure an alloy with temperature coefficient of resistance not greater than 1 X 1X per " C. and a thermal e.m.f. against copper no greater than that of the imported material. It is characteristic of manganin that the temperature-resistance curve is not a straight line but has a peak, which varies in position with different samples; it is most desirable, however, to have it at a temperature of 25' C. if possible. The coefficients of manganin from all records available ranged from a large negative to a large positive value. The composition as reported by different authorities is given in Table I. Prof. Matthew A. Hunter, of Rensselaer Polytechnic Institute, made up a number of small melts of manganin in a graphite crucible and the one that he reported as having the best cocfficient gave the following analysis: Copper, 83.6 per cent.; nickel 2.5 per cent.; manganese, 13.6 per cent.; iron, 0.3 per cent. An analysis of a sample of German manganin gave the following: Copper, 82.6 per cent.; nickel, 3.8 pcr cent.; manganese, 12.8 per cent.; iron 0.7 per cent.

Jan 1, 1921

By J. P. Nichols

Modern vibrating screening dates from about 1910 at which time the forerunner of the present day two bearing and four bearing circular motion inclined vibrating screens were first introduced. These simple machines consisted of a screen box holding some kind of a screening surface to which was attached an off-center shaft or a shaft with an off-center weight which was rotated. The rotation of these shafts caused a shivering motion to the screen box and produced the first vibrating screen. In the 1920's and early 30's, the box designs were improved and the mechanisms designs were also improved and by 1940, vibrating screens were an important part of most process plants. In the early days when the screen sizes were dictated by how much could be shoveled onto the screen box and by the force that a particular mechanism could produce, not much thought was given to the proper sizing of the particular units. As mechanism and body design improved the ability to predict vibrating screen capacity at various openings became more important. In the late 1930's, a set of empirical capacities came to be used. with few modifications, these capacities are still in use today, both by those companies that use a formula involving only the amount of fine material in a feed, and by those companies using a formula in which the total feed to a particular screen is used. In either method of calculation, the empirical values are based on these ideal conditions: (1) The material being fed to the screen contains 25% oversize. (2) The feed to the screen contains 40% half size material. (3) The material has a bulk density of 1.6 T/Cu.M. (100 lbs/cu.ft.). (4) The screening surface has an open area of 50%. (5) The material is dry, free flowing and relatively cubical. (6) The maximum screening efficiency required is between 90 and 95%. It is obvious that these conditions do not occur in natural or crushed size distributions. Therefore, modifications must be made to these empirical values to allow for the calculation of a vibrating screen for a particular set of conditions. Before we consider these various modifications, let us look at what happens to material as it is acted on by a vibrating screen so that we can better understand why the modifications are nec-

Jan 1, 1982

By F. E. Bash

PREVIOUS to the war, this country depended on Europe for its supply of a number of alloys of great importance in the manufacture of electrical apparatus and equipment. When this source was cut off shortly after the beginning of hostilities and the small stocks in the United States were exhausted, either inferior substitutes had to be used or the manufacture of the apparatus suspended. Since electrical equipment was of primary importance in the prosecution of the war, the substitutes had to be used until the composition and processes of manufacture of the alloys could be determined. Included among these alloys was one generally known as manganin, which is composed chiefly of copper and manganese and which, beside having a low-temperature coefficient of resistance, has a low thermal electromotive force against copper. These qualities make it valuable for the manufacture of electrical instruments and machines in which it is used in the shape of wire, rod, and strip. As a result of these circumstances, an investigation was started to deter mine how manganin could be made on a commercial basis so that a product of uniform quality and the necessary electrical characteristics could be produced. The object was to procure an alloy with temperature coefficient of resistance not greater than T 1 X 10-5 per ° C. and a thermal e.m.f. against copper no greater than that of the imported material. It is characteristic of manganin that the temperature-resistance curve is not a straight line but has a peak, which varies in position with different samples; it is most desirable, however, to have it at a temperature of 25° C. if possible. The coefficients of manganin from all records available ranged from a large negative to a large positive value. The composition as reported by different authorities is given in Table 1. Prof. Matthew A. Hunter, of Rensselaer Polytechnic Institute, made up a number of small melts of manganin in a graphite crucible and the one that he reported as having the best coefficient gave the following analysis: Copper, 83.6 per cent.; nickel 2.5 per cent.; manganese,-13.6 per cent.; iron, 0.3 per cent. An analysis of a sample of German manganin gave the following: Copper, 82.6 per cent.; nickel, 3.8 per cent.; manganese, 12.8 per cent.; iron 0.7 per cent.

Jan 9, 1919

Discussion of the paper of DORSEY HAGER, to be presented at the Colorado meeting, September, 1918, and printed in Bulletin No. 138, June, 191S, pp. 1109 to 1118. WALLACE E. PRATT, Wichita Falls, Tex. (written discussion*).¬Mr. Hager has touched upon interesting problems related to the broad subject with which he has entitled his paper. As to the existence of the important structural feature in the buried Bend series, which Mr. Hager constructs from well-logs, and designates as the "Bend Arch," there seems to be general agreement among a number of observers. Indeed, M. G. Cheney1 and Robt. T. Hill2 have each published structural maps of the Bend Arch that do not differ essentially from the map shown in Mr. Hager's Fig. 1. The reflection, in the overlying, unconformable Cretaceous, of certain folds in the Pennsylvanian, with which the petroleum accumulations has to do, is an important observation on the part of Mr. Hager, since, as he says, much critical territory is covered by Cretaceous, and it is highly desirable that the underlying Pennsylvanian structure be mapped, if possible. If the folds in the Pennsylvanian are of post-Cretaceous age, then it should be possible, in spite of the intervening unconformity, to determine approximately the position of buried folds beneath the Cretaceous overlap. The idea of post-Cretaceous folding would not be out of accord with the suggestion by Carroll H. Wegemann that the folding of the Permian beds in southern Oklahoma was still in progress as late as the Tertiary.3 But most observers have related the folds in the Pennsylvanian and Permian beds at the surface, both in North Texas and southern Oklahoma, to the process of. emergence of the land area at the end of the Permian. It seems more probable that the reflection of Pennsylvanian folds in the unconformable Cretaceous which Mr. Hager observed is due to long continued persistence of stresses which were largely relieved at the close of the Permian, than that the principal period of folding was post-Cre-taceous; this being the case, it seems likely that only folds of greatest intensity in the Pennsylvanian will, be decipherable in the Cretaceous overburden, and that many promising structural features are so concealed by the Cretaceous as to escape detection except by drilling.

Jan 8, 1918

By S. Shapiro, G. Krauss

We will reply to Dr. Pitsch's discussion by 1) presenting in greater detail the single surface trace analysis which we performed on the reversed austenite plates in a single parent plate of martensite of known orientation, 2) relating the results of our analysis to the conclusions which Dr. Pitsch makes on the basis of our data, and 3) examining the validity of our selection of twenty-nine individual traces from the over 200 austenite plates which were observed in a surface of this single martensite plate. Fig. 7 shows a standard (001) projection of the martensite plate from which the austenite-martensite interface traces were taken. The traces are plotted on the projection as the small solid circles, and the great circles corresponding to the loci of plane normals which could contain each trace or could intersect the surface plane along the measured directions are also plotted. It can be seen that these great circles intersect at a point which corresponds to the normal of the surface plane on which the traces were observed. Also rate which occurred only at particularly low heating rates, see Figs. 1 and 3 in the paper.2 Since in this case the interpretation of Jana and Wayman is plausible and since we have no alternative to this interpretation, we would like to state only that the existence of a diffusion-controlled reversal at low temperatures seems to be not yet proved beyond any doubt. The author wishes to thank Professor G. Krauss for making available his manuscript prior to publication. It is also a pleasure to acknowledge the lively written discussions, which the author has had with Professors G. Krauss and C. M. Wayman prior to this communication. The financial support of the Deutsche For-schungsgemeinschaft for the work on which this communication is based is also gratefully acknowledged. plotted within small dotted circles which represent a i3 deg scatter in each of the twenty-four unit stereo-graphic triangles are our A and B poles7 and the pole P determined by Kessler and itsch.' The data presented in Fig. 7 permit a direct association of the measured traces and the various proposed habit plane poles for the reversed austenite plates in the martensite crystal. If the sample measurements do in fact

Jan 1, 1969

By Albert Sauveur

SOME writers believe that when austenite transforms completely into pearlite on slow cooling through the thermal critical range, such transformation does not imply the formation of any of the so-called transition constituents: martensite, troostite and sorbite. Might it not be claimed with as much justification that when water freezes it does so suddenly, solid ice being obtained without passing through the intermediate stages of ice and water? Obviously, regardless of the speed of solidification, this would be erroneous. Before reaching the completed solid condition, this must of necessity pass through an unbroken series of stages when the system consists of mixtures of water and of ice, the former decreasing and the latter increasing in amount. Are not these "transition" stages in the freezing of water similar to the transition stages occurring in the transformation of austenite into pearlite? To clarify, let us consider in Fig. 1 the mechanism of the transformation of eutectoid steel from its austenitic to its pearlitic condition as it cools slowly through its thermal critical range. It is generally admitted that this transformation is the result of two distinct phenomena: (1) the allotropic change of gamma iron into alpha iron and (2) the crystallizing out of solution of the carbide Fe3C. Whether this crystallizing of Fe3C implies also its formation is immaterial for our purpose. In other words, whether it is the carbon in atomic dispersion which is present in gamma iron or molecules of Fe3C has no bearing upon the matter to be discussed. The transformation of gamma iron into alpha iron cannot take place suddenly. It must of necessity be progressive, regardless of the speed with which it may take place. At A, for instance, there would be present AB gamma iron and BC alpha iron. The distance MN does not refer to falling temperature, but to the passage of time. It may be assumed that the transformation takes place at a constant temperature (the Ar321 point). In a similar way, the crystallization of Fe3C out of the austenite solid solution must be progressive as depicted between M and N. At A there would be present AB gamma iron, BC alpha iron, CD carbon dissolved in gamma and in alpha iron and DE Fe3C. This condition may be described according to individual preference as martensite or troostite. To sum up, can the metal pass from condition

Jan 1, 1931

By Dorsey Hager

NORTH -CENTRAL Texas has recently become a center of interest for the oil men of America. The bringing in of the McClosky well at Ranger, Eastland County, and the shallow pool at Brownwood, Brown County, in 1917, has stimulated interest in this area to fever pitch. Oil men from all over the United States are now investing there. The area of present interest is shown by the accompanying map (Fig. 1). The money spent in leases runs into millions of dollars. It is no exaggeration to say that a strip of country 200 miles (321 km.) long and 125 miles (201 km.) wide, comprising some 15,000,000 acres (6,070,310 ha.)., has been leased practically solid at a cost for rentals and bonuses of at least $1 per acre. The test holes contracted for will certainly number 400, at a cost of at, east $5,000,000. From what has been done in the past six months, $20,000,000 at least will be spent. To pay, returns on this amount of money, new production to the extent of at least 12,000,000 bbl. must be obtained. At present, the production from new fields will not average over 5000 bbl. per (lay; three wells at Ranger are producing 3000 bbl.; 250 wells at Brownwood produce 1000 bbl.; and the Gray well, Coleman County, is as yet an unknown factor. However, at Ranger there is every indication of developing a good pool covering from 1500 to 2000 acres (607 to 809 ha;), more or less, but the wells are deep, 3400 to 3800 ft. (1036 to 1158 m.), and cost $35,000 to $40,000 to drill. Large wells are necessary to pay for such expensive holes. As new wells are drilled, the gas pressure will be lowered rapidly, and large production need not be expected. For those oil men who expect a second Cushing or an Eldorado, Ranger holds little of promise. At Brownwood, Brown County, there are some 250 shallow wells (depths from. 200 to 350 ft.) averaging 4 to 7 bbl. per day. There is a chance of an extensive producing area, for these shallow sands to the southwest, and the opening of several thousand acres of shallow oil territory, and also some promise of deeper oil horizons in the Ranger horizon, but probably all under 2500 ft.

Jan 6, 1918

GENERAL COMMITTEE GERALD F. G. SHERMAN, Chairman. ARTHUR NOTMAN, Secretary. NORMAN CARMICHAEL, JOHN C. GREENWAY, W. L. CLARK, W. G. McBRIDE, B. BRITTON GOTTSBERGER, FOREST RUTHERFORD. General Committee on Transportation WALTER DOUGLAS, Chairman. CLEVELAND E. DODGE, Secretary. ARTHUR S. DWIGHT, JOHN C. GREENWAY, JULIUS KRUTTSCHNITT, JR. Committee at El Paso W. D. GORDON, ROBERT McCART, JR., W. W. ROSE. Committee at Santa Rita JOHN M. SULLY, Chairman.

Jan 12, 1916

By AIME AIME

THE week, of April 5 will long be remembered by those that attended the Birmingham meetings of the Open-Hearth and Blast Furnace committees of the A.I.M.E. Iron and Steel Division. Birmingham iron and steel own received the 450 delegates with open arms; described and discussed their southern metallurgical practices and problems and compared experiences with their northern brother metallurgists in two days of technical sessions on Wednes-

Jan 1, 1937

By Rclssell Gibson, F. S. Turneaure

The tin deposit of Monserrat; Bolivia, consists of one major vein 1600 m in length. The ore is unusual because of the notable quantity of teallite, even though cassiterite is the principal tin mineral. The deposit, formed at shallow depth under a wide range in temperature, may be classed as xenothermal. Polished sections reveal a complex history of replacement, with low-temperature minerals deposited before high-temperature minerals.

Jan 1, 1950

By C. A. Hartnagel, D. H. Newland

The market for Pennsylvania grade showed a drop both in demand and in prices, which reacted unfavorably on New York oil production, all of which comes under that classification. The output for the year in New York amounted to 5,045,200 bbl. The production in 1937 was 5,478,000 bbl., the largest in any year for the last half century or more. Falling prices, of course, affected new drilling. They declined from $2.20 a barrel, which was posted at the start, to $1.68 in the final months of 1938. With this came a reduction in the amount of oil that would be accepted by the refineries operating in the New York fields. Conditions therefore have combined to halt, at least temporarily, the growth of oil production in the state, which had experienced a steady gain for the last 15 years or more, the yield having risen from less than 1,000,000 bbl. to the round total of 5,500,000 bbl. in 1937. Practically all the oil now obtained is from old, developed fields. No new pools have been found in the last quarter of a century or more. The larger share comes from flooding the sands. Although there are many wells that still produce without the aid of the water drive, they are small and for the most part are pumped periodically. Of late, new drilling has been restricted mainly to that required to maintain existing flood projects. Because of the high initial cost and time required to put a flood into production, the depressed condition of the market has been a serious handicap financially, and, further, has been an unfavorable influence on the planning of operations to secure the maximum recovery of the oil. Unless market conditions improve, it is certain that the effects will be shown in the yield for some time to come. Gas Developments Drilling was active in the southwestern area, chiefly in Allegany and Steuben Counties, and some notable wells were brought in that tapped the Oriskany sandstone. Altogether 42 holes were put down in the two counties, of which 31 were listed as producers and 11 were dry. The new wells gave an initial daily flow of 239,000 M cu. ft. At the close of

Jan 1, 1939

By C. A. Hartnagel, D. H. Newland

The market for Pennsylvania grade showed a drop both in demand and in prices, which reacted unfavorably on New York oil production, all of which comes under that classification. The output for the year in New York amounted to 5,045,200 bbl. The production in 1937 was 5,478,000 bbl., the largest in any year for the last half century or more. Falling prices, of course, affected new drilling. They declined from $2.20 a barrel, which was posted at the start, to $1.68 in the final months of 1938. With this came a reduction in the amount of oil that would be accepted by the refineries operating in the New York fields. Conditions therefore have combined to halt, at least temporarily, the growth of oil production in the state, which had experienced a steady gain for the last 15 years or more, the yield having risen from less than 1,000,000 bbl. to the round total of 5,500,000 bbl. in 1937. Practically all the oil now obtained is from old, developed fields. No new pools have been found in the last quarter of a century or more. The larger share comes from flooding the sands. Although there are many wells that still produce without the aid of the water drive, they are small and for the most part are pumped periodically. Of late, new drilling has been restricted mainly to that required to maintain existing flood projects. Because of the high initial cost and time required to put a flood into production, the depressed condition of the market has been a serious handicap financially, and, further, has been an unfavorable influence on the planning of operations to secure the maximum recovery of the oil. Unless market conditions improve, it is certain that the effects will be shown in the yield for some time to come. Gas Developments Drilling was active in the southwestern area, chiefly in Allegany and Steuben Counties, and some notable wells were brought in that tapped the Oriskany sandstone. Altogether 42 holes were put down in the two counties, of which 31 were listed as producers and 11 were dry. The new wells gave an initial daily flow of 239,000 M cu. ft. At the close of

Jan 1, 1939

By Russell Gibson, F. S. Turneaure

The tin deposit of Monserrat, Bolivia, consists of one major vein 1600 m in length. The ore is unusual because of the notable quantity of teallite, even though cassiterite is the principal tin mineral. The deposit, formed at shallow depth under a wide range in temperature, may be classed as xenothermal. Polished sections reveal a complex history of replacement, with low-temperature minerals deposited before high-temperature minerals.

Jan 10, 1950

Executive A. R. LEDOUX, Chairman GEORGE D. BARRON SIDNEY J. JENNINGS J. V. N. DORR J. E. JOHNSON, JR.¬ Membership J. E. JOHNSON, JR., Chairman KARL EILERS F. F. SHARPLESS R. M. RAYMOND LEWIS W. FRANCIS Finance J. V. N. DORR, Chairman CHARLES F. RAND J. V. W. REYNDERS Library E. GYBBON SPILSBURY,' Chairman ALEXANDER C. HUMPHREYS GEORGE C. STONE' JOHN H. JANEWAY BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 1, 1923

STANDING COMMITTEES Executive A, R. LEDOUX, Chairman HERBERT HOOVER EDWIN LUDLOW ARTHUR S. DWIGHT CHARLES F. RAND Membership J. V. W. REYNDERS, Chairman J. V. N. DOER W. H. ALDRIDGE EDGAR RICKARD R. M. RAYMOND Finance MARK L. REQUA CHARLES F. RAND, Chairman J. V. W. REYNDERS Library E. GYBBON SPILSBURY, Chairman ALEXANDER C. HUMPHREYS GEORGE C. STONE JOHN H. JANEWAY BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 1, 1923

PRESIDENT AND DIRECTOR JOHN M. LOVEJOY NEW YORK, N. Y. PAST PRESIDENTS AND DIRECTORS HOWARD N. EAVENSON PITTSBURGH, PA. HENRY A. BUEHLER ROLLA, Mo. VICE-PRESIDENT, TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS LOUIS S. CATES NEW YORK, N. Y. PAUL D. MERICA NEW YORK, N. Y. WILFRED SYKES CHICAGO, ILL. R. C. ALLEN CLEVELAND; OHIO HENRY KRUMB NEW YORK, N. Y.

Jan 1, 1936

By A. L. Mular

Several capital cost estimation procedures are reviewed briefly, although the factored estimate method is discussed in preference. A table of cost versus equipment parameter data is provided, where the cost may be updated from the current value of the M&S cost index for mining and milling. Cost equations are useful to prepare computer programs which perform capital cost calculations. The use of the factored estimate method is illustrated.

Jan 1, 1978

Arizona FRANK A. WARDLAW, JR., Chairman GRANT R. RUBLY, Secretary-Treasurer Miami Copper Co., Box 505, Miami, Ariz. MICHAEL CURLEY C. R. KUZELL BURRELL R. HATCHER A. MENDELSOHN WILLIAM KOERNERA. C. REIFSNIDER Black Hills L. B. EAMES, Chairman ALEXANDER J. M. Ross, First Vice-Chairman FRANCIS CHURCH LINCOLN, Second Vice-Chairman NATHANIEL HERZ, Secretary-Treasurer Lead, S. D. JOSEPH P. CONNOLLY C. N. KRAVIG C. E. DAWSON EDWARD L. TULLIS

Jan 1, 1939