Search Documents

By Porter W. Shimer

It docs not seem to be generally known that some American pig-irons contain notable amounts of vanadium, and while the present investigation is far from covering the whole range of irons, it is hoped that, at least, it may serve to call attention to the importance of looking for this element. The majority of the pig-irons investigated were made in the Lehigh Valley and neighboring furnaces, using more or less New Jersey magnetite in their mixtures. Many of these ores, and probably all of them, contain a little vanadium as well as titanium; the ore from one of the largest of these mines contains 0.05 per cent, of vanadium and 0.60 per cent. of titanium. Dr. Thomas M. Drown was the first to detect the presence of vanadium in the incrustations1 occurring on certain pig-irons, and he also found this element in a number of magnetites, but the methods for its accurate determination had not, at that time, been well worked out. In a general way, it may be said that the Lehigh Valley pig-irons contain from 0.02 to 0.05 per cent. of vanadium and from 0.10 to 0.20 per cent. of titanium. These elements follow the silicon; that is, the furnace-conditions which produce a high-silicon, low-sulphur iron will cause the maximum reduction of vanadium and titanium, and

Jan 1, 1913

By David Reger

THE value of carbon ratios in determining the boundaries of possible oil deposits appears to have passed the hypothetical stage. The theory that the ratio of fixed carbon in pure coals is an, invariable index of incipient metamorphism in both, surface and underground rocks and that it may be applied in defining the limits of petroleum, advanced by David White,1 has been received with keen interest by many petroleum geologists. Detailed isocarb maps have been prepared of the Pennsylvanian area of North Texas and Eastern Oklahoma by M. L. Fuller.2 A similar map of the coal-bearing area of West Virginia is given here. An isocarb3 is a line showing an equal fixed-carbon percentage, pure coal basis; the term has been proposed by David White to supersede a less expressive nomenclature. The term carbon ratio is applied to the percentage of carbon in pure coal after water and ash have been eliminated. As a comparatively small number of analyses have been made on this basis, it is usually necessary to compute the ratio by dividing the fixed carbon of the proximate analysis by the sum of the fixed carbon and volatile matter of the same analysis. Many thousands of proximate analyses have been made by the West Virginia Geological Survey, covering nearly every county in which coal is found. Numerous others have been made by the. U.S. Geological Survey and the U. S. Bureau of Mines, but as uniformity of results is

Jan 2, 1921

By Lennart Bergstedt, Olov Fägremo

Boliden Metall Aktiebolag, the prime base metal mining company of Sweden, treats some 10-10.9 t/y (11-12 stpy) of sulphide ore in nine concentrators. During the years considerable effort has been devoted to the development of all phases of the technology of ore prospecting, mining, milling, smelting and refining. This has been necessary due to the complex and low grade ores. The autogenous grinding technique was first studied within the company as early as 1945. Basic test work commenced during the early fifties, whereby the merits of pebble grinding could be evaluated. In parallel with the converting of the rod mill/ball mill grinding systems to rod mill/pebble mill systems, the development work concerning the feasibility of autogenous grinding went on resulting in the installation of a 8 6.7 x 2.1 m (8 22 x 7 ft.) cascade mill at the Vassbo lead mine in 1959. Long term tests at the Vassbo plant together with a number of pilot plant test involving low grade silicious ores and pyritic comples base metal ores successive led to a better understanding of the process of autogenous grinding. Before a two stage autogenous grinding system could be chosen for the expansion of the Aitik copper mine, a carefully planned survey concerning grinding characteristics and variances in the ore and flowsheet was undertaken. The expanded plant went on stream in 1972 and in the beginning of 1973 and since then has performed excellently.

Jan 1, 1979

By M. J. Richards, A. Szirmae, G. R. Speich

The formation of austenite from ferrite, ferrite plus retastable carbide, spheroidite, and pearlite has been studied in a series of irons, Fe-C alloys, and plain-carbon steels using fast heating techniques. In the absence of carbide, austenite nucleates at ferrite/ferrite grain boundaries; nucleation is followed by the rapid growth characteristic of a massive transfornation. The trarnsformation occurs at 950°C at heating rates of 106º C per sec and cannot be suppressed. Metastable carbide dissolves before austenite forms and does not influence the transformation kinetics. For spheroidite structures, austenite nucleates preferentially at the jinction between carbides and ferrite grain boundaries. Growth from these centers proceeds until the carbide is completely enveloped; subsequent growth occurs by carbon diffusion through the austenite envelope. For pearlite structures, austenite nucleates preferentially at pearlite colony intersections. Carbide la)?zellae dissolve at the advancing austenite interface but complete solution of carbide does not occur; the residtial carbide is eventually dissolvled or spheroid-ized depending on the carbon cuntent. The magnitude and temperature dependence of the austenite growth rate into Fe-C pearlite when incomplete carbide dissolution is assumed are satisfactorily explained by an approximate colume diffusion model. The impurities present in plain-carbon steel reduce the growth rate of austenite in comparison to that jound in an Fe-C alloy. The formation of austenite has been studied in much less detail than the decomposition of austenite. This is primarily a result of the importance of harden-ability in determining the mechanical properties of steel. Recently, more interest in the kinetics of austenite formation has resulted from the discovery by Grange1 that rapid heating techniques strengthen steel by refining the austenite grain size. Although the strengthening effect is not large, it is accompanied by no loss in ductility. In addition, interest continues in rapid heat treatment of low-carbon steel sheet for tin plate applications.2,3 Among the few systematic studies of austenite formation are the early work of Roberts and Mehl4 on formation of austenite from pearlite and recent work of Molinder5 and of Judd and paxton6 on formation of austenite from spheroidite. Also, Boedtker and Duwez7 and Haworth and paar8 have recently studied the formation of austenite from ferrite in relatively pure iron, Kidin et al.9,10 have studied the formation of austenite in 8 pct Cr steels, and Paxton has recently discussed various aspects of austenite formation in steels." The present work was undertaken to determine the kinetics of austenite formation for a variety of starting structures including ferrite, ferrite plus metastable carbide, ferrite plus spheroidal cementite, and ferrite plus pearlitic cementite. Emphasis was placed on determining the active sites for austenite nucleation, determining the temperature and time range of austenite formation, and in the case of pearlite a careful study of the growth rate of austenite was made in the absence and presence of impurities. By using a variety of heating techniques including laser-pulse heating, it has been possible to study austenite formation in an isothermal fashion over a wide range of temperatures. EXPERIMENTAL PROCEDURE The alloys studied in the present work are a zone-refined iron with 4 pprn C, an Fe-C alloy with 130 pprn C, 2 Fe-C alloys with 0.77 and 0.96 wt pct C, and a plain carbon steel with 0.96 wt pct C. The zone-refined iron and Fe-C alloys contained 60 pprn and 200 pprn total substitutional impurities, respectively. The plain carbon steel contained 2400 pprn Si, 2000 pprn Mn, and 900 pprn Cr. Various heat treatments were given to these alloys to produce different starting structures of equiaxed ferrite, ferrite plus metastable carbide, fine pearlite, and spheroidite. These heat treatments are given in Table I. A wide range of heating rates were employed in this work because many of the reactions occur so quickly at temperatures in the austenite range that they are completed during the initial heating cycle unless very fast heating rates are used. Essentially the same heating techniques employed by Speich et a1.12 and Speich and Fisher13 were used in this work. For time intervals of 2 sec to 20 hr, simple hand immersion of 0.010-in. thick specimens in a Pb-Bi bath was employed. These specimens were quenched in a 10 pct NaC1, 2 pct NaOH aqueous bath. For time intervals of 100 m-sec to 2 sec, an automatic dunking and quenching device was employed with 0.002-in. thick specimens. Again, liquid Pb-Bi baths were used for a heating medium but now helium gas quenching was employed. For time intervals of 2 to 100 m-sec a laser heating device was employed with 0.002-in. thick specimens; a helium plus fine water-droplet spray was now used for quenching. Additional information on heating times shorter than 2 m-sec was obtained by study of the zones around the centrally heated laser spot. Here diffusion of heat from the centrally heated zone raises the temperature of the specimen locally to all temperatures between ambient and the peak temperature, but for times of the order of microseconds. All the heat-treated specimens were examined by

Jan 1, 1970

By James W. Dally, William L. Fourney, Anders Ladegaard Peterson

For the past 3 years, the authors have been conducting research sponsored by the National Science Foundation (RANN) to improve the process of excavation by drilling and blasting. The approach followed has been experimental where the development of stress waves and fractures initiated at the bore hole have been investigated in order to obtain a complete understanding of the dynamic fracture process. The second step in the approach has been to introduce modifications in the drill and blast procedure which will permit closer control of the fracture process. The laboratory investigations involve high speed photography where the dynamic fracture process is recorded with a Cranz-Schardin 1, 2 multiple-spark camera. The camera is equipped with 16 spark gaps which are pulsed at 25 K volts to produce an intense but very short (0.5 sec) flash of light. The camera is capable of recording 16 photographs of a dynamic event at framing rates which can be varied from 30,000 to 1,500,000 frames per second. The exposure time is sufficiently short to stop motion associated with detonating explosive charges and to make visible the details of the fracture process at a bore hose. The bore hole in a massive intact rock formation is modelled with a two dimensional plate containing a circular hole to represent the bore hole. The model material employed is a transparent polyester known commercially as Homalite 100.* This polymeric material is extremely brittle as evidenced by its extremely low fracture toughness of [ ]. The fracture toughness is a measure of the ability of a material to resist the propagation of flaws or small cracks. In comparison, Schmidt3 has recently measured the fracture toughness of Salem limestone and determined [ ]. Thus, the Homalite 100 should closely model the brittle nature of rock where fractures occur at small flaws and propagate without any apparent plastic deformation. Homalite 100 is also birefringent, which indicates that it becomes optically anisotropic when subjected to either static or dynamic loads. Circularly polarized light is transmitted through the loaded Homalite 100 model in a polariscope4 and the birefringence produces an optical interference pattern which is called a fringe pattern. For dynamic photoelasticity, the multiple-spark camera is equipped with polaroid filters to produce the circularly polarized light required to generate the photoelastic fringe patterns. An example of a singlespark frame showing a fringe pattern from a typical experiment is presented in [Fig. 1]. The photograph was taken 0.000072 sec (72 sec) after the detonation of the explosive charge. The circular fringes are due to the outgoing dilatational or P type stress wave and travel with a velocity of 85,000 in. per sec (2260 m/sec) in the Homalite 100. The P wave is followed by a second lower velocity stress wave known as the shear or S type wave which propagates at a velocity of 49,000 in. per sec (1245 m/sec). In the local neighborhood of the bore hole, several radial cracks are visible. These cracks propagate at essentially a constant velocity of 15,000 in. per sec (380 m/sec) prior to arrest. The fringes about the crack tips and in the local region of the bore hole are primarily due to the residual gases contained in the bore hole after the explosive charge was detonated. Sixteen frames similar to this one are recorded during the experiment to give full field visualization of the dynamic event at 16 discrete times over its duration. The fringe order number N is related to the difference in the principal stresses of and 02 according to a stress optic law4: [ ] where f0 = material fringe value, and h = model thickness. The wholefield dynamic-fringe patterns provide a basis for simultaneously observing the interaction between propagating cracks and the stresses which drive these cracks. Fracture Control Experiments Improvements in the efficiency of the drill and blast procedures must involve close control of the fracture process following the detonation of an explosive charge in a bore hole. By control it is implied that the number of cracks initiated and the location of each crack on the wall of the bore hole can be specified. Control also, involves orienting each crack and maintaining the crack path and velocity until the specified crack length is achieved. If the entire fracture process can be controlled, then rounds can be designed to optimize volume removed. fragment size and minimize costs. One area of blasting where fracture control is vitally important is in underground excavation where the strength and stability of the rock walls must be maintained and smoothness and precision of the walls must be achieved. The smooth blasting method is one of the most commonly employed procedures for achieving some degree of fracture control. In smooth blasting, the central region of material is first removed, and then the final row of closely spaced undercharged or cushioned holes are fired to remove the final volume and produce a smooth wall. In some instances, unloaded or dummy holes between the loaded holes are recommended to guide the fracture plane. This investigation pertained to an evaluation of 3 features of the smooth blasting process. These included (a) the effect of stress reinforcement on fracture by simultaneously firing 2 charges; (b) the influence of a dummy hole on control of the fracture planes between 2 simultaneously fired charge holes; and (c) the influence of dummy hole spacing on fracture plane control.

Jan 1, 1979

By R. A. Graham, R. W. Rohde

The effect of hydrostatic pressure upon the austenite start temperature of a commercial Fe-28.4 at. pct Ni-0.5 at. pct C alloy has been determined. For pressures to 20 kbar, the austenite start temperature decreased from its atmospheric pressure value of 380°C at the rate of about 4°C per kbar. These data are analyzed by two different thermodynamic approaches; first, considering the transformation as an isothermal process, and second, considering the transformation as an isentropic process. It was found that both these approaches fit the experimental data equally well. The effect of hydrostatic pressure upon the austenite start temperature is best described by considering the mechanical work done during the transformation as that work obtained by multiplying the applied pressure with the gross volume change of the transformation. It is widely recognized1 that strain has an important effect on the initiation of martensitic transformations.* For example, the martensite start tempera- *In this paper, use of the term martensitic transformation implies the reversal of martensite to austenite as wen as the formation of martensite from austenite. ture, M,, may be increased by plastic deformation. Similarly, plastic deformation is observed to lower the austenite start temperature, A,. The effect of uniaxial stress on the M, of iron-nickel alloys has been studied by Kulin, Cohen, and Averbach.2 They found that the martensite start temperature was significantly changed by stresses well within the elastic region. Moreover, the effect of tensile and compres-sive stresses differed. These effects were explained in terms of the interaction of the applied stress with both the dilational and shear components of the transformation strain. The magnitudes of the influence of uniaxial tension, compression and hydrostatic pressure on Ms were measured in 30 pct Ni 70 pct Fe by Pate1 and Cohen.3 Their thermodynamic calculations and similar calculations by Fisher and Turnbull4 predicted the experimental results when the transformation was assumed to occur isothermally at some fixed driving force. This driving force was assumed to be supplied by a combination of the chemical free energy difference between the austenitic and martensitic phases and the work performed during transformation by the applied stress. More recently, Russell and winchel15 reported the effect of rapidly applied shear stress on the reversal of martensite to austenite in iron-nickel-carbon alloys. They performed a thermodynamic analysis of this transformation based upon the assumption that the re- versal occurred adiabatically. They concluded that the applied shear stress did not significantly interact with the transformation strain and thus did not assist in inducing the reversal. Rather they concluded that the reversal was effected by localized strain heating which resulted from the gross local shear deformation of the experiment. In either the adiabatic or isothermal analysis it is necessary to compute the work performed by the interaction of the applied stress and the transformation strains. In the case of hydrostatic pressure this interaction has been treated by two different methods. In either case the applied pressure is assumed to remain constant during the transformation. In one treatment the applied pressure is assumed to interact directly with the dilatational strain associated with the formation of an individual martensite plate.3'4 This local strain has been measured at atmospheric pressure in iron-nickel alloys by Machlin and Cohen.6 In the above treatment this local strain is assumed invariant with temperature and pressure changes. In the other treatment the applied pressure is assumed to interact with the gross volume change of the transformation.7,8 The usefulness of this latter treatment has been demonstrated by Kaufman, Leyenaar, and Harvey7 who calculated the effects of pressure upon the martensite and austenite start temperatures of Fe-10 at. pct Ni and Fe-25 at. pct Ni alloys. Excellent agreement was obtained between their calculations and their experimental data on an Fe-9.5 at. pct Ni alloy. However, this treatment suffers from the fact that the data required to calculate the volume change of the transformation (i.e., the initial specific volumes, the thermal expansion and compressibility data for both the austenitic and martensitic phases) is, in general, not available for any material except pure iron. Thus the calculations of Kaufman et al.7 were necessarily performed by assuming that the volume change of the martensitic transformation in the iron-nickel alloys was that same volume change occurring during the a-? transformation in pure iron. While this approximation may suffice for very dilute alloys it is likely to be inaccurate in high nickel alloys. We have performed measurements of the effect of hydrostatic pressure to 20 kbar on the A, temperature of an Fe-28.4 at. pct Ni-0.5 at. pct C alloy. The composition is similar to the alloy used by Pate1 and Cohen3 to determine the effect of pressure upon the M, temperature. The present measurements permit calculation of the interaction between the applied pressure and the transformation strain. Additionally, measurements have been made which allow precise determination of the gross volume change of the transformation. The data allow direct comparison between the alternate hypotheses of the interaction between the applied pressure and a dilatational transformation strain characterized by either the formation

Jan 1, 1970

NORTH AMERICA ALASKA Anchorage.-Strandberg, H. College.-Barber, R. J. Burns, W. T. Henricksen, R. Henton, H. M. Joesting. H. R. Comet.-Albertson, F. E. Douglas.-Cahill, W. E. Carlson, L. Fairbanks.-Andregg. J. N. Coats. R. R.

Jan 1, 1938

By H. J. Morel-Seytoux

The influence of patten, geometry on assisted oil recovery for a particular dispIacement mechanism is the object of investigation in this paper. The displacement is assumed to be of unit mobility ratio and piston-like. Fluids are assumed incompressible and gravity and capillary effects are neglected. With these assumptions it is possible to calculate by analytical methods the quantities of interest to the reservoir engineer for a great variety of patterns. Specifically, this paper presents (1) very brieily, the methods and mathematical derivations required to obtain the results of engineering concern, and (2) typical results in the dorm of graphs or formulae that can be used readily without prior study of the methods. Results of this work provide checks for solutions obtained from programmed numerical techniques. They also reveal the effect of pattern geometry and, even though the assumptions of piston- like displacement and of unit mobility ratio are restrictive, they can nevertheless be used for rather crude but quick, cheap estimates. ,These estimates can be refined to account for non-unit mobility ratio and two-phase flow by correlating analytical results in the case M = 1 and the numerical results for non-piston, non-unit mobility ratio displacements. In an earlier paper1 it was also shown that from the knowledge of closed form solutions for unit mobility ratio, quantities called "scale factors" could be readily calculated, increasing considerably the flexibility of the numerical techniques. Many new closed farm solutions are given in this paper. INTRODUCTION BACKGROUND Pattern geometry is a major factor in making water-fIood recovery predictions. For this reason many numerical schemes have been devised to predict oil recovery in either regular patterns or arbitrary configurations. The numerical solutions, based on the method of finite difference approximation, are subject to errors often difficult to evaluate. An estimate of the error is possible by comparison with exact solutions. To provide a variety of checks on numerical solutions, a thorough study of the unit mobility ratio displacement process was undertaken. To calculate quantities of interest to the reservoir engineer (oil recovery, sweep efficiency, etc.), it is necessary to first know the pressure distribution in the pattern. Then analytical procedures are used to calculate, in order of increasing difficulty: injectivity, breakthrough areal sweep efficiency, normalized oil recovery and water-oil ratio as a function of normalized PV injected.

Jan 1, 1967

By H. W. Mead, C. E. Birchenall

SELF-DIFFUSION of iron in austenite is a process which may play a significant role in some of the practically important reactions which occur in solid irons and steels. It also provides a system in which the interaction of vacancies on substitutional sites and atoms in interstitial positions may be investigated. For both purposes, accurate values of the diffusivities are required. Two sets of previous measurements exist, each containing features which require checking. In the course of an investigation to determine the rate of diffusion of iron in certain steels, Garwick and Rosenqvist' measured the self-diffusion coefficient of iron in a 0.10 pct* C steel and obtained a dicated that while at lower temperatures D increased with increasing carbon content, at the higher temperatures it first increased and then decreased. At the same time the activation energy decreased linearly from a value of 69,000 cal per g-atom for pure iron to 33,000 cal per g-atom at 1.06 pct C. This rapid decrease in activation energy implies that iron at higher temperatures within the austenite range would diffuse more slowly in high carbon steels than in steels of lower carbon content. Experimental Procedure The radioactive iron used in this work was obtained from Oak Ridge National Laboratory. The unit consisted of about 1 microcurie each of Fe7 and Fe It was allowed to decay for two years. At the end of this time most of the Fe with a half-life of 46.3 days, had decayed, while most of the original Fe(half-life 2.91 years) still remained. The iron as chloride was extracted into an ether layer, using the method of Ashley and M~rray. After evaporation of the ether the iron chloride was dissolved in 250 ml of aqueous solution containing 2.4 gpl Fe. The compositions of the steels used are listed in Table I. Disks of ¾ in. diam and about ¼ in. thick were machined from these steels for use in diffusion couples. The disks were surface ground on both sides to ensure parallel opposite faces. One face of each disk was polished through 000 emery paper. Half of the prepared disks were plated with radioactive iron. For this, 1 ml of the radioactive iron

Jan 1, 1957

El Indio, eighty percent -owned by Compania Minera an Jose Inc., a subsidiary of St. Joe Minerals, and twenty percent-owned by private Chilean investors, will open their new flotation and Carbon -In -Pulp plant near La Serena, 480 km (300 miles) north of Santiago, Chile, in early 1981. The underground mine, at an altitude of 4,270 m (14,000 ft), will produce about 1,270 mt per day (1,400 st per day) of ore containing about 2. 2570 Cu, and gold and silver to the extent of 16 and 254 g per mt (0.47 and 7.4 oz per st) respectively. While construction of the plant was underway, development ore, containing some 1,400 kg (45,000 oz) of gold, was shipped to the United States for recovery in a copper smelter. At El Indio the underground ore is rail-hauled to the mill a short distance from the portal where it is crushed, ground, and floated to produce a copper concentrate containing both gold and silver. The crushing plant also crushes waste for use as mine backfill. Approximately 92% of the copper and 60% of the gold and silver are recovered in the flotation concentrate. Flotation tailings, at a grade of 19 g Au and 116 g Ag per mt (3.4 oz Au and 0.55 oz Ag per st), are cyanided for 72 hours in six Pachucas with auxiliary air lifts for pulp transfer. Lime, cyanide, lead nitrate, and a phosphate are also fed to the cyanidation Pachucas. After cyanidation, the pulp is treated in four air lift Carbon-In-Pulp tanks equipped with external vibrating screens for carbon advance. Loaded carbon is stripped in two pressure vessels in parallel. Pressure stripping must be used because of the high altitude. Stripped carbon is dewatered in a spiral classifier before being reactivated in a rotary kiln and returned to the C. I. P. circuit. Pregnant solution is then sent to four banks of four Zadra cells for gold and silver recovery on steel wool. Zadra cell cathodes.are washed with the slimes being captured in a plate and frame filter. The filter cake and the washed cathodes are then dried on an infrared dryer and smelted in two stages to bullion bars. Published reports indicate that the total investment for this unique operation was in the neighborhood of $80 million.

Jan 1, 1981

By Wallace Ralston

The East Texas district includes the northeast 38 counties of the State of Texas. It still remains one of the most important oil-and-gas-producing areas of the United States, since it includes within its boundaries the large East Texas field. Other fields of importance are: Van, Rodessa, Talco, Cayuga, Long Lake and Sulphur Bluff. Production is from the Nacatoch, Blossom, and Woodbine of the upper Cretaceous and the Paluxy and Glen Rose of the lower Cretaceous. Of these, the Woodbine is the most important, since it is the producing horizon iri the East Texas field. Fields East Texas Field.—There were 2471 oil wells, 1 gas well and 84 failures completed during the year of 1936 in the East Texas field; that is, 1565 fewer than in the year of 1935. The total number of producing wells is now 22,031, of which 50 are temporarily shut down; 18,435 wells flowing their production; 3150 pumping; 293 on gas-lift, and 82 operated by other methods. This shows an increase of 1642 wells on artificial lift over Jan. 1, 1935. The average daily salt-water production is estimated at 42,700 bbl. from 2327 wells—an increase of 1201 wells over the year of 1935. The field is now drilled to an average density of one well to 5.85 acres. Average bottom-hole pressure has dropped from 1193 Ib. to 1168 lb., approximately 1 lb. drop for each 6,600,000 bbl. of oil produced. During the month of December 1936, the estimated daily average production of illegal oil had dropped from 20,500 bbl. in December 1935 to 7500 bbl. The commercial gas production is of minor importance in the East Texas field, and figures for the amount of gas taken from the field are not available at the present time. Talco Field, Titus and Franklin Counties.—The discovery well was drilled by Housh, Thompson et al. on the C. M. Carr tract and completed in March 1936, as a pumping well making 552 bbl. per day of 24' gravity oil. This well was first completed at a total depth of 4208 ft., the top of the sand being 4190 ft. Later it was deepened to 4260 ft., which increased the production from 552 to 725 bbl. per day. This field is producing

Jan 1, 1937

By Paul R. La Pointe

GEOTECHNICAL OBJECTIVES OF UCG PROGRAM Underground coal gasification (UCG) is one of several in situ extraction technologies for utilizing deep, otherwise unmineable coal. This technology involves the injection of air or oxygen into the target coal seam, ignition of the coal and recovery of product gases. Geotechnical characteristics of the coal and enclosing rock strata strongly influence the success of this Process. The flame front follows the coal cleats (Hill, 1979), and cleating and bedding control the manner in which coal collapses into the cavity, thereby affecting recovery efficiency (Ramirez and others, 1982). Moreover, coal seams typically behave as fracture dominated aquifers in which cleat orientations govern subsequent contaminant dispersal. For these reasons, the Anaconda Minerals Co. undertook a detailed study of fracturing within the Wyodak-Anderson Coal in the eastern Powder River Basin (PRB) near its Rocky Hill UCG test site (Fig. 1). STRESS HISTORY AND FRACTURING IN THE POWDER RIVER BASIN Vertical jointing, or cleating, in coals may arise from shrinkage shortly after deposition under low confining pressures, or later in time, soon after burial but after the coalification process is well advanced (Ting, 1977). There is much evidence to support the formation of cleating after coalification (e.g. Hawkes and Mellor, 1970; McCulloch and others, 1974), which suggests that the stress state existing at that time strongly influences cleat formation. McCulloch and others (1974) argue that the typically better developed face cleat forms parallel to the plane containing [ol] and [o2]. Where the relation between cleats and stess has been studied (McCulloch and others, 1974; Stone and Snoeberger, 1977; Ward, 1977; Kulander and Dean, 1978), the highly systematic face cleat strongly parallels the [o1] direction. Stone and Snoeberger (1977) report face and butt cleat measurements of N70E and N29W for the Felix Coals 220 m stratigraphically above the Wyodak at the Hoe Creek UCG site (Fig. 1). Structural trends also indicate the past state of stress in the PRB. Glaze and Keller (1963) suggest that the NE-SW regional compression during the late Permian formed major N-S fold lines and basement magnetic anomalies. Mapel (1959) describes folds having N60W and N30W rends in the northern PRB, as well as a large normal fault trending northeast. Glass (1976) also describes normal faults trending northeast. Similarly, Olive (1957) mapped normal faults

Jan 1, 1984

[Abstmct of remarks by R. II. Sweetser arid suhscqueut discussion at the New York Meeting, February, 1926. The Transactions mill ultimately contain a report of work resulting from these discussions. Need for a standard of ualuration.—There should be an accepted method for evaluating the different kinds of bituminous coals based on their carbon just as that for iron ores is based on iron. Variation in the classes of coals and their desirability fol the different industrial uses is analagous to the case of iron ores. The iron people have developed a standard. In the past coals have not been intelligently distributed because the public has not been informed as to its uses. Many operators have known nothing about the final disposal of the coal shipped from their mines. Sales agents and retailers have had no means of evaluating coals except to make the price as high as the market will stand. Producers and distributors need to know how much more valuable the coals would be if prepared so as to contain less objectionable material. Mr. Swectser cnlletl on the Goal and Coke Committee of the Institnte to organize a study through producers and users to develop a method scientifically and comnereially sound E. A holbrook said that the information exists but the public is unwilling to investigate. He praised Ashley's1 nomenclature of the different kind of coal which has been accepted by the Coal Mining Institute of America and recommended to the American Enginecring Standards Commitee. G. S. Rice pointed out the wider variety and distribution of consumption of coal compared to Iron ore. C'. M. Young approved Mr. Sweetser's remarks and hoped lor a research institution, probably endowed, to study utilization of coal after it comes from the ground. Mr. Sweetser cited incidents to prove his former statements. He said that a reduction of 1 per cent. ash in the coal would cut down the cost of pig iron at a blast furnace 30 c. a ton, that the coal men should tell what the iron men would have to pay to get better coal. H. J. Prryn endorsed the need of blast-furnace operators to know the kind of coal from which their- coke is made and the latler's ash content, as this affects coke consumption. A. C. Fieldncr explained that the difficulty of evaluating coal on the basis of chermical analyses for calorimetric tests is: (1) representativr

Jan 1, 1927

By G. A. Croes, N. Schwarz

This paper reports the results of a series of model displacement experiments carried out for measuring the efficiency of the water-drive process. This series forms a continuation and extension of that described by Engel-herts and Klinkenberg. Detailed information has been obtained on the influence of the oil/water viscosity ratio. The results are represented in the form of a diagram from which both the oil recovery and the water/oil ratio can be easily read off as a function of the total production (oil plus water) for all values of the viscosity ratio M between I and 500. These resu1ts are viewed in the light of the two existing theories on water flooding, viz. that of Buckley and Leverett and that of Dietz. It is shown that if the Buckley-Leverett theory applies, the relation between the relative permeability ratio and saturation, which plays a major role in this theory, (.an be calculated with a high degree of accuracy from the results of the model experiments. Dietz's theory is found to be in agreement with the experimental results in a certain range of circumstances. A discussion of the physical background of the Buckley- Leverett and Dietz theories makes it clear why the latter fails to agree with some of the experimental results. INTRODUCTION For an economical exploitation of oil fields both a rational control of natural (primary) recovery processes and a proper application of artificial (secondary) recovery methods are essential. These require detailed information upon the dependence of the relevant flow processes on the variables by which they are governed. Three methods are available for obtaining this information: (1) (statistical) analysis of actual field data; (2) appropriately scaled model experiments; and (3) mathematical analysis of the physical problem. If sufficient data were available, the first method would, in principle, be the most reliable one, although it has the drawback that the basic relationships between the variables involved are to a large extent obscured by the natural inhomogeneities of most reservoirs. The most profitable procedure seems to be: (a) determining the fundamental relations for idealized reservoirs by methods (2) and (3); (b) checking the consistency of the results obtained by these two methods; and (c) establishing the range of applicability of these methods to actual reservoirs by comparison with the data accumulated under (1). In this paper items (a) and (b) are dealt with for the case of homogeneous loose sands initially saturated

Jan 1, 1956

By Charles Wurms, Robert Steinitz

DURING an investigation to determine the compatibility of several metals with tungsten, the degree of reaction between tungsten and lead was determined. A literature survey showed considerable disagreement between the results of various earlier investigators. Information presented by M. Hansen1 states that, according to S. Inouye,2 tungsten has very poor resistance against attack by molten lead, even at the low temperature near the melting point of lead. A phase diagram in the same reference indicates a solubility of 30 wt pct W in molten lead at 1300°C. Contrary evidence was shown by Parkman and shepard3 in their investigation of materials for use in heat transfer systems containing liquid lead alloys; they performed experiments at 980°C for times up to 50 hr without noticing any appreciable attack on the tungsten. Tungsten sheet was immersed in molten lead contained in Vycor tubes evacuated to at least 10-4 mm Hg. R. Bernard4 and R. I. Jaffee5 also indicate that no reaction occurs between molten lead and tungsten. However, no experimental data were included in these reports. In order to settle the question of the solubility of tungsten in molten lead, tungsten powder with an average Fisher subsieve particle size of 6µ was pressed in a double-acting die at 6 tsi to small compacts. They were then sintered in an atmosphere of hydrogen for 2 hr at 1700°C, resulting in a sintered density of 64 pct of theoretical with final dimensions of 0.260 in. in height and 0.245 in. in diameter. For all tests, the tungsten pellets were immersed in molten lead. Table I is a summary of the experimental procedures showing atmospheres, temperatures, and times. The first experiments were performed at 650°C; at this temperature, the liquid lead should wet the porous tungsten better than at its melting point, and penetrate into the pores. The lead was heated in a graphite crucible with a graphite cover. No protective atmosphere was used, as it was expected that the formation of CO would be sufficient to prevent oxidation. This, however, proved to be wrong, and all tungsten samples showed a slight oxide film after treatment. The tungsten samples were immersed in the molten lead for times of 5 min, 10 min, 1/2 hr, 1 hr, and 2 hr. After this time, the melt was poured into a form and the

Jan 1, 1962

By R. S. French, W. R. Hibbard

M. Balicki—As one who some years ago spent much time searching for an alloy with high thermoelectric power that would be suitable for heat energy-electric energy converter based on the principle of a thermoelectric pile, I would like to make a few comments touching upon that aspect of this excellent paper. The specifications which one of the authors has formulated so aptly do not appear to me as complete, and I would like to add to them the following two demands: (1) Melting point not less than 500°C and (2) elongation on 2 in. at least 5 pct. Condition 1 would insure good thermodynamic efficiency of the pile by permitting a reasonably high temperature of the hot junction and at the same time making it suitable for such application as salvage of vast amounts of energy which is lost in the form of sensible heat of waste gas leaving industrial and other furnaces. Condition 2 is also a very important one; particularly, because of the fact that all elements and alloys which exhibit attractive thermoelectric properties seem to be as a rule very brittle. The design, erection, and maintenance of a pile incorporating a brittle material in one of the most crucial parts of the converter would be a very difficult and costly affair indeed. To illustrate this point I may mention great difficulties I encountered when trying to make thermocouples of silicon. Casting of 1/4-in. rods in iron or graphite mould yielded only broken pieces which had to be welded into a bar. Such a bar had to be handled very carefully during the determinations. Raising the molten silicon by vacuum into a silica tube and solidifying it there solved the problem of stability as well as that of electrical insulation of a bar. On tests this bar (98.5 pct Si) showed dE/dT = — 275.5 microvolts per degree C vs. copper. Thermocouples made of this grade of silicon and pure nickel developed 0.39 v when temperature of the hot junction was approximately 1000°C. The possibility Dr. Gonser has mentioned of trying to impart to metals good thermoelectric properties by alloying them with silicon, has been considered. The preliminary survey which I have made was, however, disappointing. Perhaps, it will be advisable to record the results obtained (table VI), as this might save repetition of search in fields already covered.

Jan 1, 1951

By J. R. Martson

The arrangement of the larger furnace at the United Verde smelter, together with the boiler layout and connecting flues, is shown in Fig. 1. The important dimensions are given in the figure, and cross-sectional areas of combustion space, flues, etc., are recorded. The location and extent of the baffling in the boilers also are shown because of their importance in the interpretation of the data. Two boilers serve each reverberatory furnace. They are of the class M-26 Stirling type (rated at 713 boiler hp. each). Steam is generated at 178-lb. gage pressure at a total temperature of 528" F., from feed water at a temperature of 113" F. The feed water is condensate from turbogenerators plus make-up softened by the lime-soda process. The make-up is rather large in amount as it must match the amount of steam consumed in reciprocating blowing engines and the like, which are not served by surface condensers. As a result the boiler feed water has a hardness of 1.5 to 3.0 grains per gallon, but this results in the formation, during six months to one year of boiler operation, of scale only of "eggshell " thickness or less. The boilers are set at the same elevation as the tapping floor of the furnace, which results in the introduction of the waste-heat gases at the top of the front bank of tubes and necessitates the inversion of the usual baffling arrangements. The boilers are equipped with valve-in-the-head soot blowers, which keep most of the dust blown off the surface of the tubes, but it is necessary to supplement the soot blowers by high-pressure air lances, inserted by an attendant through side doors in the boiler setting. Deposits of coal ash and of dust from the furnace charge accumulate in the flues between the reverberatory furnaces and the boilers and this necessitates cleaning of these connecting flues by hand during the greater part of one of the three 8-hr. shifts during each 24 hr. This cleaning operation requires the opening of clean-out doors, which, of course, has some effect on the yield of steam. Revebberatory Furnace Practice The United Verde furnaces are fired with pulverized coal of sub-bituminous type of which the screen and chemical analyses are given in Table 1.

Jan 1, 1934

By R. A. Bergier

The Transactions of the Institute contain nothing, as yet, on the subject of pocket-compasses; and in the belief that American miners, explorers, geologists, and engineers will gladly welcome any infor mation about new forms of apparatus, simple in construction and adapted to rapid use, I offer a short description of an improved French combination pocket-compass, which, if once introduced into use, would seem likely to supersede similar instrumens of older pattern. The instrument in my possession I owe to the kindness of M. G. de.La Bouglise, of Paris. The frame of the compass is a double-bottomed box, 2 1/2 inches square and 9/16 of an inch high, made of white metal, and with its sur faces very carefully planed. The sides of the box make true right angles with each other. Two sides are parallel with, and two are normal to, the north and south line of the principal graduation. The bottom is accurately planed, so that the instrument will lie true on a plane surface. A glass, 2 3/8 inches in diameter, is set in the top plate. The graduation for the needle is engraved on the upper face of a ring, connected with the flat disk, in which the center-pin is in serted. Between this disk and the bottom of the box there is a hollow space a quarter of an inch deep. The needle is 1 7/8 inches in length, and can be balanced by means of a small sliding piece of metal. The graduation extends from 0° to 360°, reading from right to left. The stopping of the needle is effected by a screw, A, on the side of the box near the handle, H (Fig. 1). There is also a clinometer attachment, the graduation for which is engraved on the upper face of the silver-plated disk. The compass has two sights. The north sight, B, is a simple pin, a little more than an inch high, which, when not in use, is kept folded down, and is partially protected by the exterior sliding-plate, C. When raised for use, the sight is stopped in a vertical position by a projecting pin attached to the side of the box.. The south sight, D, is connected with the handle, H, and the sight and handle

Jan 1, 1890

By B. D. Cullity, J. T. Norton, M. Telkes

M. Balicki—As one who some years ago spent much time searching for an alloy with high thermoelectric power that would be suitable for heat energy-electric energy converter based on the principle of a thermoelectric pile, I would like to make a few comments touching upon that aspect of this excellent paper. The specifications which one of the authors has formulated so aptly do not appear to me as complete, and I would like to add to them the following two demands: (1) Melting point not less than 500°C and (2) elongation on 2 in. at least 5 pct. Condition 1 would insure good thermodynamic efficiency of the pile by permitting a reasonably high temperature of the hot junction and at the same time making it suitable for such application as salvage of vast amounts of energy which is lost in the form of sensible heat of waste gas leaving industrial and other furnaces. Condition 2 is also a very important one; particularly, because of the fact that all elements and alloys which exhibit attractive thermoelectric properties seem to be as a rule very brittle. The design, erection, and maintenance of a pile incorporating a brittle material in one of the most crucial parts of the converter would be a very difficult and costly affair indeed. To illustrate this point I may mention great difficulties I encountered when trying to make thermocouples of silicon. Casting of 1/4-in. rods in iron or graphite mould yielded only broken pieces which had to be welded into a bar. Such a bar had to be handled very carefully during the determinations. Raising the molten silicon by vacuum into a silica tube and solidifying it there solved the problem of stability as well as that of electrical insulation of a bar. On tests this bar (98.5 pct Si) showed dE/dT = — 275.5 microvolts per degree C vs. copper. Thermocouples made of this grade of silicon and pure nickel developed 0.39 v when temperature of the hot junction was approximately 1000°C. The possibility Dr. Gonser has mentioned of trying to impart to metals good thermoelectric properties by alloying them with silicon, has been considered. The preliminary survey which I have made was, however, disappointing. Perhaps, it will be advisable to record the results obtained (table VI), as this might save repetition of search in fields already covered.

Jan 1, 1951

Year of Election 1944 Walter Hull Aldridge, New York, N.Y 1955 Louis S Cates, New York, N.Y 1946 William Fraser (Lord Strathalmond), London, England 1917 Herbert Hoover, New York, N Y 1955 George M Humphrey, Cleveland, 0

Jan 1, 1959