Search Documents

By I. L. Follington

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.1 Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production, Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required. A mechanism has been postulated for the deformation behaviour of the roof and pillars in a mechanised pillar extraction operation from the continuously monitored data, observational data and results of previous studies. The 7 m wide fenders were observed to yield under abutment stresses before lifting commenced. The stability of these fenders throughout the lifting sequence was considered to be dependant upon the magnitude of their post peak load carrying capability. This is influenced by the post peak stiffness and the extent of roof lowering in the vicinity of the fender. Difficulties with fender extraction occurred where remnant coal left standing in the goaf caused uncaved goat to bridge to the mined fender. Difficulties were also experienced where sub-vertical jointing occurred in the roof of the split reducing it's ability to bridge effectively. Despite the relatively short monitoring period, the potential role and application of continuous monitoring in advancing understanding of the rock mass response to mechanised pillar extraction operations has been demonstrated. This understanding now requires enhancement and shows great potential for aiding the optimisation of mechanised pillar extraction operations.

Jan 1, 1992

By Yoshiaki Fujii

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic array. Location of microseismic events and intensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the intensity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increasing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are considered. Observed and predicted displacement of the shaft axis agreed well. Third, is the roadway deformation in Taiheiyo Coal Mine. Attainable maximum stress for a roadway was calculated considering three faults intersecting the roadway. It was realized that the roadway's convergence is related to the calculated stress by simple equations.

Jan 1, 1992

By Nicholas Chlumecky

One of the most dangerous jobs in mining is that of resupporting the roof after a fall has occurred. The resulting cavity may be more than 30 feet high, with relatively unstable sides and roof. It is often impossible to proceed with rehabilitation without exposing men and equipment to unsupported rock. Temporary supports provide margin- ally effective protection because of the lack of available footing. Furthermore, the usual supports in rehabilitated fall locations are not permanent, require frequent maintenance, and fail to eliminate some remaining serious safety hazards. This is typically the case for high cavities where loose rock drops from considerable heights from between roof bolts. Supports made of cribbing, beams and additional cribbing to the high points of the fall in many cases do not provide good protection due to the deterioration and shrinkage of timber. In mines, high cribbing frequently loses contact with the roof and thus provides no protection against rocks peeling off the sides. This is true in spite of the fact that at time of installation the cribbing was wedged tightly to the roof. Therefore, when considering the difficulties which occur with current practices, the objective is to find alternate methods of resupporting the high roof after a fall.

Jan 1, 1981

By John A. Rusnak

Point load testing is used to determine rock strength indexes in geotechnical practice. The point load test apparatus and procedure enables economical testing of core or lump rock samples in either a field or laboratory setting. In order to estimate uniaxial compressive strength, index-to-strength conversion factors are used. These factors have been proposed by various researchers and are dependent upon rock type. This study involved the extensive load France and point load testing of coal measure rocks in six states. More than 10.000 individual test results. From 908 distinct rock units, sere used in the study. Rock lithologies were classified into general categories and conversion factors were determined For each category. This allows for intact rock strength data to he made available through point load testing for numerical geotechnical analysis and empirical rock mass classification systems such as the Coal Mine Roof Rating (CMRR).

Jan 1, 2000

By Hui Chen

The paper describes the use of a physical model technique to investigate the failure modes of mine tunnels with reference to the in situ stress field. The characteristics of stratification commonly encountered within UK coal mining conditions have been taken into consideration. The investigation has indicated that the weak floor strata in coal mining tunnels, under the action of high rock stresses, will be subject to the floor lift problem in both predominantly horizontal and vertical stress fields. However, the failure mode and mechanism varies between the two stress field patterns. In the predominantly horizontal stress field, the tunnel floor tends to fail by gradual bending of the laminations, whilst in the predominantly vertical stress field, the floor tends to fail by a shearing action with the failed material lifting in the form of a block. The failure mechanism is discussed with reference to mechanics theory.

Jan 1, 1993

By Antoni Kidybinski

Coal mining both with longwall and room-and-pillar method often encounters severe operational difficulties due to had roof conditions. Rooffalls at entry cross-cuts or along the rib line in longwalls as welt as dynamic and excessive loads on supports due to overhanging of strong roof layers in a goab - are well known phenomena to the mine operators. Also, a number of practical examples may be quoted of dramatic improvement of working conditions after changing of coal winning technology or supports type. It is therefore a question to be answered how far we are able to recognize roof strata properties before mining starts and adjust both coal extraction technology and supports of entries to rock stability foreseen. Furthermore, engineering principles and criteria for decision making should be established. In recent years several in situ rock strength and discontinuities detection testing techniques have been developed both indirect (geophysical) and direct thus making possible closer roof-strata examination. In this paper critical roof span criterion is discussed as a basis for selection of proper mining system in terms of desirable stability of mine opening .

Jan 1, 1982

By Hamid Maleki

The U.S. Bureau of Mines implemented a monitoring program in a western U.S. coal mine for the evaluation of both conventional and alternative support systems. The conventional support consisted of 2.5-m-long vertical bolts installed in an 5.5-m-wide entry. The alternative system consisted of 2.5- and 3-m vertical and inclined bolts installed at a higher density during widening of a cut from 3.6 to 5.5 m. Roof deformation, roof stress, rib deformation, and bolt loads were monitored during the 2-month test period. In addition, roof failure patterns and lithology were characterized within the six-entry main test section. Results were analyzed using roof deformation and failure profiles, roof stress profiles. bolt loading and bending moment diagrams, and numerical models. The mechanics of roof deformation, failure, and support reaction in three zones in the mine roof were characterized. Significant improvements were shown in roof stability in the section using the alternative system. Results are encouraging and indicate the effectiveness of alternative support systems and excavation techniques for limiting inelastic deformation of roof in highly stressed underground mines.

Jan 1, 1994

By M Nombe

Based on the analysis of a case study at POWELTON No.2 MINE, it was determined that mine stability problems had occurred due to floor softening. A fireclay (underclay) layer in the immediate floor was softening after coal extraction and failing under pillars load. The thickness of soft floor was considered as the governing factor in the determination of the magnitude of floor displacement. The effect of floor thickness on floor displacement was evaluated by creating seven models that were input into the LAMODEL program. The properties of the soft floor were determined from a bearing capacity test performed in the Mains close to the area where mine stability problems had occurred. Moisture increase was considered in the reduction of floor bearing strength. Various strain-softening properties were allocated to the materials representing the soft floor. The LOW GAP POWELTON No.2 MINE was modeled and LAMODEL program was used to determine stress and convergence on both the coal seam and the fireclay seam. The results of critical stress and convergence obtained from modeling were compared with the actual floor failure area in the mine.

Jan 1, 2002

By Yi Luo

Accurate mechanical and geological information of the roof strata is vital for roof bolting design in underground mines. In order to obtain such information in a timely manner, a research has been under way to develop a technology for mapping the roof geology using the drilling parameters acquired during the roof bolting operations. In this paper, a systematic approach has been proposed for determining the rock strengths using the acquired real-time drilling parameters. A computer simulation program based on the mathematic model has been developed to verify the approach and to study its sensitivity. The method has been used to interpret the acquired drilling data.

Jan 1, 2002

By Joel Bradley, Kot Unrug, Kyle Perry, Mark Klimek

"A West Kentucky mine operation in No. 11 seam, encountered floor heave, due to the localized increase of the thickness in the fireclay mine floor. Floor heave has overridden seals installed in two mined out panels. The third seal’s location was planned for isolating that area from the Mains. A plan of support has been developed to prevent repetition of the floor heave and related problems outby the seals. The applied ground control measures were successful. An attempt of a 3D numerical modeling was made, that it would match the observed behavior of the mine floor and could be used as a design tool in similar conditions. In the paper described are sequence of events, a mitigation ground control system applied, and the first stage of numerical modeling.IntroductionWest Kentucky coal mine operation in the No. 11 seam has approached an area where the fireclay floor thickness increases to about 5 ft. Delayed floor heave has been observed. In the first sealed area (Panel KK), floor heave has overridden the seals and has begun to progress outby. This could not be allowed at the new seal location PP described in this paper because such override would affect the mains. Previously numbers of standing support systems were used, but their effectiveness was not satisfactory as is illustrated in Figure 1, Figure 2, and Figure 3. Therefore, with sealing of the next area approaching, mine management was looking for a better solution that would eliminate the problem. In that stage, our team looked closely at the geology and strength of roof and floor, as well as the characteristics of ground failure around the seal at the first site. The technical literature has been searched as well Haramy et al. 1986 Hsiung and Peng 1987, Peng 2008, Santos & Bieniawski 1987. This led to the identification of factors responsible for the ground failure. It has been determined that increased fireclay thickness from typically less than 2 ft to about 5 ft, when compared to the previously mined parts of reserve, and the strong limestone strata just above the immediate roof composed of 2 ft of black shale, created conditions of failure. It appeared that, when pillars were punching into the mine floor, the strong roof did not break but was bending, exerting high pressure on outby pillars, causing rib failures and closure. This is a similar mechanism to a strong roof affecting longwall shields. The remedial action planned was additional support."

Jan 1, 2015

By P. A. Gray

Artificial ground support has developed into a relined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bait is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By David Conover

Knowledge of the magnitude and direction of the horizontal secondary principal stresses is a critical factor in designing the layout and mining sequence of underground openings. Typically, horizontal stress measurement has been accomplished using overcoring or hydraulic fracturing. Hydraulic fracturing can be accomplished from surface boreholes prior to development, but the technique relies on numerous assumptions regarding the rock mass and the stress field, and interpretation of results is somewhat subjective. Traditional overcoring provides a more precise measurement, but requires underground access. To allow for precise measurement of the horizontal stress field from surface boreholes, the In-situ Stress Tool (1ST) was developed by SIGRA Pty of Brisbane, Australia. Used in conjunction with HQ wireline coring, the 1ST contains a battery-powered data logger that records tool orientation and monitors six diametral deformations as the tool is overcored. The IST has been used successfully for several years in Australia, but has only recently been introduced in the United States This paper discusses how the IST was used to measure the pre¬mining horizontal stresses at a western U.S. coal mine. Seven successful measurements were obtained in two holes at depths ranging from 250 to 800 ft. Results were consistent, showing moderately biaxial stresses greater than those expected from gravity loading, but relatively low compared to rock strength. In addition to describing the overcoring equipment and procedures, various problems encountered during testing and the accuracy of the results will be discussed.

Jan 1, 2004

By Guy Reed, Russell Frith, Kent Mctyer

"Coal pillar design has historically been based on assigning a design factor of safety (FoS) or stability factor (SF) to coal pillars according to their estimated strength and the assumed overburden load acting on them. Acceptable FoS VALUES (have been assigned based on past mining experience, and at least one methodology includes the determination of a statistical link between FoS and probability of failure (PoF).The role of the pillar width-to-height (w/h) ratio has long been established as having a material influence on both the strength of a coal pillar and its potential mode of failure. However, there has been significant professional disagreement on using both FoS and w/h ratio as part of a combined pillar system stability criterion, as compared to using FoS in isolation. The argument is that, as w/h ratio is intrinsic to pillar strength, which, in tum, is intrinsic to FoS, it makes no sense to include w/h ratio twice in the stability assessment. At face value, this logic is sound.However, this paper will argue that there is a valid technical reason to bring w/h ratio into system stability criteria (other than its influence on pillar strength), as it is related to the post-failure stiffness of the pillar, as measured in situ, and its interaction with overburden stiffness.When overburden stiffness is bought into pillar system stability considerations, two issues emerge. The first is the width-to-depth (W/H) ratio of the panel, in particular whether it is sub-critical or super-critical from a surface subsidence perspective. As a minimum, this directly relates to the accuracy of the pillar loading assumption of full tributary area loading. The second relates to a reevaluation of pillar FoS based on whether the pillar is in an elastic or non-elastic (i.e., post-yield) state in its as-designed condition, as relevant to maintaining overburden stiffness at the highest possible level.The significance of the model presented is the potential to maximise both reserve recovery and mining efficiencies without any discernible increase in geotechnical risk, particularly in thick seams and higher depth of cover mining situations. At a time when mining economics are, at best, marginal, removing potentially unnecessary design conservatism without negatively affecting safety is of interest to all mine operators and is an important topic for discussion amongst the geotechnical community."

Jan 1, 2016

By Anil Mahyera

Under contract to the Bureau of Mines, a roofbolting machine has been developed which will: control torque on the bolthead to within 4 percent of a set point, control thrust to a low level (150 lbf), and implement a tightening method to minimize variability due to bolt tension decay of a group of bolts caused by differing anchor creep rates. This bolter was used to determine bolthead and thread friction factors, and to determine the effect of adding a hardened washer to the bolt assembly on the uniformity of bolt tension in the laboratory and field. Recommendations for torquing speed, bolt lubrication, use of hardened washers, and thrust level on the bolthead are made. The relationship of this system to Improved roof control is discussed, along with additional work that remains to be performed. Patent Notice Patents are pending which protect the hardware and methods of controlling tension decay as discussed in this paper.

Jan 1, 1981

By Ruixiang Gu

The de-confinement mechanisms of unstable failures as they occur in deep coal mining conditions are investigated using a distinct element numerical modeling code. The Mohr-Coulomb and continuously yielding joint constitutive models were used to study the compressive failures in coal and slip behavior of coal-rock interfaces, respectively. The effect of strength variations within interfaces on the failure mechanism of mining faces is also studied. The stability of interface slip failures was found to have a significant role in the failure mode of coal sidewalls. When the interfaces experience stable slip failures, the sidewalls are more likely to fail in a stable manner. With occurrence of unstable slips at interfaces, unstable compressive failures of sidewalls are triggered. The numerical modeling results support the proposed de-confinement mechanisms and emphasize the importance of including the coal-rock interface behavior in the analyses of unstable compressive failures. The significance of the proposed mechanisms in underground mining conditions is that rock discontinuities with large cohesion drop can become potential factors, inducing unstable compressive failures at ribs and mining faces. Therefore, the de-confinement mechanisms should be taken into consideration in mine design.

Jan 1, 2014

By T. P. Mucho

Mine roof failure due to excessive horizontal stress has been recognized as a major cause of hazardous roof conditions in some mines. Stress measurements gathered by the U.S. Bureau of Mines (USBM) at 24 different eastern mines show horizontal stress to be typically 2 to 3 times as great as vertical stress. The focus of current Bureau work is to develop detailed design parameters to assess and control the effects of horizontal stress. To facilitate the recognition of horizontal stress effects and to easily determine principal stress direction without resorting to cumbersome, expensive, and time consuming field measurements, the Bureau has developed a stress mapping methodology. Stress recognition and direction determination are required to successfully employ a number of control strategies such as mine layout, mining sequences, and support optimization to control the effects of horizontal stress, thereby increasing the safety of U.S. coal mines. This approach has been used in other major coal producing countries, most notably Australia and the UK, and has greatly enhanced the safety of their mines (1). This paper discusses horizontal stress, directional based control techniques, and provides guidelines for the use of the stress mapping technique. A case study of a mine where the technique has been used is also presented.

Jan 1, 1994

By Craig Collins

The objective was to develop a Real Time Drilling Display System for Rotary Roof Bolting using Analyzing Software to display mapped holes as they are being drilled in real time. The Analyzing Software was developed to analyze and interpret drill sensor data produced during a rotary drilled roof bolt hole by using algorithms and drill sensor data trends to find and locate roof separations or voids. After this software was validated through lab and field testing, its application needed to be tested in a production environment. However, the current method used to record the drill sensor data proved to be cumbersome for the mine to use on a continuous production basis. With different more practical mediums being explored and considered, a Drilling Display System was developed that will both map holes in real time and record the data for later review. With the Analyzing Software's current level of accuracy and with the convenience offered by the real time Drilling Display, the Drill Display System was implemented along with a test mine's current roof control plan and tested as a roof separation "Early Warning System". After installing the Drilling Display System onto a machine, input and suggestions from the mine environment were considered and design changes were made. The real world application provided a design direction that made the information produced by the Analyzing Software both convenient and significant for the test mine. Also, using the Drilling Display System increased the number of drilled holes that were both mapped and recorded. The results from studying these recorded data files lead to refinements in the current algorithms used by the Analyzing Software which increased the overall accuracy and capability of the system A fairly accurate representation of void or separation locations in the mine roof can be determined fromsensor data recorded during production bolting cycle. The immediate feedback on the local roof condition that the Drilling Display System provides, amounts to a quicker and safer alternative to the scratch hole and the video bore-scope examinations that arc performed after the bolting is completed. This project has shown that making the alternative method of examining the roof condition practical for the mine to use is just as important as the accuracy of its results. Based on the results of this field test, this or other methods of reviewing the analyzed drill hole data will be explored.

Jan 1, 2004

By Revendra Awasthi

The application of a horizontal inclinometer and a tiltmeter to measure tilt, curvature, and deformations of shallow footings during mine subsidence is described. The measurements were taken during mining of a longwall panel in Southern Illinois and were supplemented with precision level survey data. Monitoring was conducted under a cooperative agreement between the Institute for Geotechnology at The University of Tennessee, Knoxville, the U.S. Bureau of Mines, the National Science Foundation, the Illinois Mine Subsidence Insurance Fund, and Old Ben Coal Company. Six different footings were constructed and instrumented at two sites; one above the panel centerline, and the second inside the edge of the panel in the anticipated zone of maximum tension. A brief description of the inclinometer casing and tiltplate installation is described, and the results obtained from the two instruments on a plain concrete footing compared. Observations of footing deformations and curvatures calculated from the inclinometer and tiltmeter data are also presented, and the results compared with observed structural damage.

Jan 1, 1990

By Andrew J. Hyett

The ISRM commission on testing methods has recently presented Suggested Methods for rock stress determination (Kim & Franklin, 1987). This proposes that even if the magnitude of in situ stress is not sufficient to cause significant ground problems, the optimum shape, orientation, and layout of underground structures can be significantly affected by it. In the design of underground excavations, the engineer often requires a knowledge of the average in situ stress tensor in the rock mass. However, attempts to measure a stress state applicable to design have proved frustrating, and a high degree of uncertainty is introduced by the variability in results. In the belief that deduced fluctuations are random in nature, many separate measurements are often made, so that a more reliable stress tensor average, and some indication of the associated variance (see Dyke et al., 1986) can be calculated. Unfortunately, this approach is limited by economic considerations and, as with any sampling procedure, it is imperative to understand the sources of measured variability, in order to design an optimum measurement programme. Cundall(1987) itemised the main causes of stress variability as a. Instrument and measurement errors, and b. Natural fluctuations of stress from point to point, induced by the action of a boundary stress on the internal rock structure. At least four categories exist: i. inhomogeneous rock, bedding, intrusions etc.; ii. differential contraction, creep, or changes in rock properties with time; iii. proximity to faults or discontinuities; iv. cycles of tectonic activity that cause movement on joints. The latter was successfully investigated using the distinct element programme UDEC. In this paper, the contribution of items (iii) and (iv) (i.e. the items related to discontinuities) to the total stress variability will be discussed, for the kind of rock mass shown in Figure 1. Although many authors have concluded that rock joints have an influence on the stress in their vicinity, a more analytical approach is required if the stress distribution associated with different jointed rock masses is to be (i) compared, and (ii) related to routinely measured joint parameters. If this can be achieved then, prior to any attempt to measure stress in a jointed rock mass, a consideration of joint geometry, joint deformability, and the geological kinematics of joints (e.g. the magnitude and direction of previous movements), can place valuable `common sense' constraints on the expected stress system for minimal extra cost.

Jan 1, 1989

By Ken Mills

This paper describes the first successful use of hydraulic fracturing to induce caving events "on demand" in Australia. Moonee Colliery operate a longwall immediately below a thick conglomerate strata. This strata temporarily bridges across the extracted longwall panel to create a large area of standing goal' When this standing goat' eventually collapses, the windblast generated presents a significant hazard to men working on and around the longwall face. Hydraulic Fracturing has been successfully introduced to take control of the timing of these caving events so as to eliminate the risk of windblast injury, The longwall face area is completely evacuated during the treatment. Water is pumped into an injection point located in the conglomerate strata above the standing goat. A horizontal fracture is generated and grows outward from the in point, separating the conglomerate strata below the fracture horizon_ At some point the strata can no longer span and a goat fall is initiated. After a treatment, mining can be recommenced with the windblast hazard eliminated.

Jan 1, 2000