Search Documents

By R. Pixler

Arch Mineral Corporation and Rocky Mountain Energy's Medicine Bow Mine in Wyoming presented an interesting challenge to the concept of mining a multiple-seam, dipping coal in the Hanna Basin. The 3362 and 2962 pits at MBCC were designed in a multiple seam coal consisting of 4 (and in some areas 5) bands of coal; these coal beds are all in the Ferris formation. The area was subject to some localized faulting and a major fault caused a physical restraint that we mined up against in our final cut. Using a 1570 dragline as the principal stripping machine, the concept of developing a bench for stripping the lower seams from the low-wall side of the pit was initiated. The results of this method of stripping were very satisfying for this pit through the completion of pit life and prompted us to use it in other areas at MBCC and at our other operations. Mining a dipping coal presents a small twist to conventional "flat" coal stripping. The spoil has a tendency to continually try to slide into the pit and the increased overburden on each cut as you mine down the dip creates spoil problems unless adequate design provisions are made prior to stripping.

Jan 1, 1986

By E. Baliktsis

PPC (Public Power Corporation) operates a new power plant at the South-West part of Crete. Recently the extension of the Power Plant started. ATHENA SA the main contractor of the project assigned to EXORIXI SA the implementation of a blast vibration monitoring program and prevention-evaluation of risks caused by construction blastings inside or very close to the operating part of the power station. The blasting parameters and characteristic elements that had been evaluated, the measures that had been taken and materialized, the overall risk management and the results of the whole program are presented in this paper.

Jan 1, 2006

By C. W. Schultz

The Alabama tar sands of the Hartselle Sandstone formation present a more difficult problem in primary extraction than do the Athabasca tar sands. In contrast to the Athabasca tar sands, the Alabama tar sands are "oil wetted" and the contained tar, or bitumen, is of much higher viscosity. A physical beneficiation scheme was developed in which clean sand from an external source was used as a scrubbing medium. High intensity scrubbing liberated the tars which are readily recovered by froth flotation. Locked cycle tests have shown that, after the use of an initial ration of clean sand, the system produced enough new clean sand to be self sustaining.

Jan 1, 1992

By C. S. Davis

In being asked to present this paper on the improvements in loading and hauling equipment and the effect on unit costs, Mr. Van De Water, your program chairman, stated that his reason for coming to a contractor was due to the wide experience of, and I quote: "a large contracting firm using a variety of equipment on varying types of earth moving jobs." We people in Utah Construction Company are flattered that Mr. Van De Water singled out our Company for this assignment. Utah Construction Company's participation in open pit mine stripping antedates the 1920's, when overburden was being removed from copper ore in Bingham Canyon, Utah. Our first stripping con¬tract for the Copper Company was finished in 1912. Since that early beginning, Utah has, as a contractor, been engaged to strip and mine iron ore properties, coal properties, copper properties, uranium properties, phosphate,-gypsum, limestone and dolomite properties. And, as you know, the Company has become a major producer of iron ore from Company-owned open pit mines. Utah Construction Company has been instrumental in the evolution of open pit mining tools. Some of the first tools were the old wood and coal fired stream shovels which had to be fired hours before a shift started to insure a full head of steam, providing power to excavate with the then large 1-1/2 cubic yard buckets. Today, Utah's strip mining is done, with 18 cubic yard and 10 cubic yard crawler shovels. Yesterday's horse and mule drawn, iron wheeled wagons, with 1 and 2 cubic yard capacity, which were hand dumped by removing the false bottom, one 2 x 4 at a time, have been replaced by today's- 50-ton capacity, hydraulic, rear dump trucks and giant 40-ton coal haulers. Utah Construction Company used the early fresnes and wheeled scrapers which were horse and mule drawn. Often, an operator holding too tightly to a handle was thrown into his horses when a hard spot turned the scraper, a contrast with today's 20 and 25 cubic yard, self-powered diesel and diesel electric Gargantuan rigs; with power controls that relieve the operator of practically all physical work. This Company has pioneered many of today's advances in equipment with shop made prototypes, features of which were adopted and elaborated upon by equipment manufacturers.

Jan 1, 1959

By M. P. Meehan

The purpose of this paper is to present the key elements in a system; study of the electrical system for a timing and/or tilling operation. The ability of an electrical system to function in a reliable fashion at its proper levels is essential for an operation to be successful. A system study consists of a load study for determining the capability of the electrical network to provide power to the various loads and a short circuit study for determining the capability of the electrical protective equipment to properly protect against fault conditions. The sequence of events in a system study is data acquisition, determining the electrical parameters and analyzing the ability of the system to meet these requirements. If the system is small, herd calculations will be the manner in which the study will be conducted; if it is large then commuters will be used. A load study has as its objectives the determination of the capability and reliability of the source of power, transformers and conductors to satisfactorily deliver power to the loads at an acceptable voltage level. The Information required is a single line diagram showing the source, transformers, conductors and loads.

Jan 1, 1980

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By Richard A. Thomas, Liming Yuan, Lihong Zhou, James H. Rowland

Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners.

Current scrubber capacities vary from 1.89 to 4.72 m3/s (4,000 to 10,000 cfm), and there is interest in using scrubbers with capacities up to 6.61 m3/s (14,000 cfm). This paper describes research to compare the effectiveness of blowing and exhausting face ventilation systems using high-capacity scrubbers with flows up to 6.61 m3/s. Tests were conducted in a surface ventilation gallery with exhaust and blowing systems operating under similar conditions. The mining machine was equipped with a machine-mounted scrubber. Methane gas was released at constant flow at the mining face and measured at several face locations. Effectiveness of exhausting and blowing systems was compared by determining average face methane concentrations. For each operating condition tested, blowing ventilation was more effective than exhausting for controlling face methane levels. Raising scrubber flow to 6.61 m3/s reduced methane levels for both blowing and exhausting systems.

Jan 1, 1996

By Constance F. Acton

This paper presents an overview of -- the carbon-in-pulp process for gold and silver recovery as seen in the early 1980's. Traced back to its origins in the mid-nineteenth century the process development through the present state-of-the art is described. The process technology and equipment design are described in detail for the carbon-in-pulp process. A typical process flowsheet is given with a description of appropriate design criteria. Technical advantages and disadvantages as compared to the traditional countercurrent decantation process are discussed including some illustrative comparisons of capital and operating costs. A summary of currently operating carbon-in- pulp plants throughout the world is given with an insight into future developments in this industry.

Jan 1, 1982

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By L. E. Murr

Solution flow in leach dumps and heaps or in columns of representative rock has been the subject of only limited studies. This is a regime involving unsaturated flow in semiconsolidated rock with a wide size distribution. Even the concepts of continuous flow systems are fairly recent, and have evolved from the search for better methods of operating industrial chemical reactors. (1-3) Waste rock consolidation and permeability play a key role in solution flow characteristics. Harris (4) suggested that bulk density variations in a leach dump could alter the particle-to-particle contact, and that large particle aggregates could act like single, large particles . In the limiting case where the bulk density approaches that of the undisturbed, consolidated rock, the entire waste unit would behave as a single particle. Roman (5) treated the phenomenon of bulk density and its effect on consolidation in terms of lixiviant flow paths or solution channeling in leach dumps. Like Harris, he assumed that no solution moved through particles or particle aggregates associated with zones of high bulk density. Solution flow paths are thus effectively separated by particle regimes, creating solution channels in the waste body. While some attempts have been made to describe solution flow in leach dumps and related systems by utilizing computer model approaches and laboratory- scale simulations (5,6), there have been no direct, large-scale observations of solution movement in channels or of the actual channel sizes and distributions within a waste body. This paper describes a series of experiments involving large-scale, controlled waste leaching tests, conducted over a period of several years, and aimed at providing some direct observation of the changes in waste consolidation and permeability, the size and distribution of solution channels, the movement of such channels with continued solution application, and other features relating to solution flow during the leaching of low-grade waste. These results are then combined with mineralogical information to explain observed leach behavior.

Jan 1, 1981

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By Bryson D. Trexler

Slope stability in open pit mines is governed by rock structure, rock quality, ground water conditions, blasting, pit geometry and excavation method. Of these factors, the control of ground water pressures often represents the primary tool to improve slope stability. Production equipment has recently been used to stabilize two slide areas by dewatering using blasthole drills for vertical holes and secondary drills for horizontal holes. This paper describes both of these dewatering programs and contrasts an earlier slope stabilization program that employed a subcontracted horizontal drill.

Jan 1, 1983

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By M. Z. Rashad

The intersection of joint sets and excavation planes leads to removable blocks which can be expected to fall or slide. The amount and cost of supports required to stabilize these blocks of excavation are related to the number and dimensions of key blocks, the mechanical properties of joints and the active forces present. In this work, the application of the block theory in the study of the kinematics and stability of removable blocks is investigated considering any number of sliding faces for some Egyptian limestone quarries.

Jan 1, 1993

By F. S. Knoll

GENERAL INTRODUCTION Electrostatic separation has found a number of applications since its initial installation as a processing method. Three broad types of electrostatic installations are discussed in order to provide a practical guide for three widely divergent uses of electrostatic separation. Only operating and installation data are covered in detail. A detailed technical treatment on the various types of electrostatic separation described in this paper can be found in the literature by F. S. Knoll, J. B. Taylor and J. E. Lawer.8, 9 ELECTROSTATIC SEPARATION OF IRON ORE: WABDSH MINES, CANADA Introduction Electrostatic roll-type separator technology which had been in use in various forms since the 1920's evolved in the late 1940's when this separation process was developed and applied to the extraction of titanium bearing minerals from beach sands by J. H. Carpenter. Equipment design and industrial flowsheets developed for the recovery of rutile and ilmenite found new application in iron ore by chance in the year, 1956. From the time of the first beach sands plant, Carpco had developed other technology, gravity and magnetic separation to better serve the beach sands industry. It was in the fall of 1956 that an iron ore producer from the upper Michigan Peninsula sent a sample of jaspilite (fine-grained specular hematite in a jasper matrix) to Carpco's laboratory for the purpose of determining if a new high-intensity magnetic separator would be beneficial. Process Development W. P. Dyrenforth, while presenting a paper on the subject in the fall of 1957, recounts the laboratory tests. "High-intensity magnetic separators have been employed (for the beneficiation of iron ore) with some success and are still being investigated. Magnetic separation is a natural field of investigation, since iron and magnetism have been almost synonymous since ancient times. As a matter of fact, when Carpco first began investigating the possibilities of upgrading specular hematite, the first thought was in terms of magnetic separation; and the second thought was in terms of gravimetric separation. It was found

Jan 1, 1986

By Dennis A. Beiter, Kenneth G. Fields, Richard T. Stoltz

Section 56.5001 Title 30, [Code of Federal Regulations1], establishes requirements for respirable dust exposure in Metal and Nonmetal Mines based on the Threshold Limit Values (TLV's) adopted by the American Conference of Governmental Industrial Hygienists. Respirable dust samples collected by Mine Safety and Health Administration (MSHA) inspectors at a sandstone quarry showed certain workers were exposed to excessive concentrations during development of a "coyote tunnel" that was ventilated with a blowing system. Because exhausting face ventilation systems are known to control dust more effectively than blowing face systems, a change was proposed to improve worker respirable dust exposures. This paper describes the evaluation of the proposed exhausting ventilation system in the quarry's "coyote tunnel" and compares the respirable dust exposures with those measured by the MSHA inspectors with the blowing system. Results showed the proposed exhausting ventilation system reduced respirable dust exposures to less than 20 percent of those measured by MSHA inspectors when the blowing system was used.

Jan 1, 1993

By George H. Roseveare

Early flotation dealt primarily with the bulk concentration of sulphide minerals or the separation of one sulphide from another and was referred to as oil flotation because oils and fats were used as reagents. The separation or concentration of one nonmetallic mineral from another developed later with the use of fatty acids. Fatty acids are organic acids present usually as glycerides in tall oil and oils of fish, peanut, cottenseed, soya beans and ethers of veg¬etable and animal origin. Some, of these oils and their derivatives were used by the Phoenicians as early as 600 B.C. in making soap, and the use of such reagents in mineral dressing is referred to as "soap flotation". The first use of oleic acid for the recovery of minerals was the early agglomeration process.' The coarse particles of ore, from 1/16 to 1/4 inch diameter, were coated with large amounts of soap or oil and after screaming from the gangue were recovered by screening, hydraulic or table classification. In 1886, a patent was issued to Mrs. Carrie Everson in which the essential feature was the constituted commingling of pulverized ore, fat or an oil, either animal, mineral, or vegetable, for the purpose of effecting .a. union of the free metal or metallic portion of the ore with such admixed material whereby the same may be changed in subsequent separation of quartz or other rock therefrom by washing or other suitable means. The patent mentions the use of red, cotton seed, caster, sperm and linseed oils, In the early use of collectors the amount of oil for froth flotation was often 2 to 6 per cent by weight of the ore rather than pounds per ton.

Jan 1, 1959

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of US coal companies are developing seams previously considered too deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas in coal beds increases with depth, and ventilation requirements are much more stringent for deep mines than for shallower mines. When the longwall mining method is wed at great depths, ventilation, ground control, and operational considerations all influence the design of longwall panels. This paper examines these influences, particularly ventilation and operational considerations, on the feasibility of two-, three-, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1988

By Reynold Q. Shotts

Underground mines, penetrating well below the water table, quickly fill with water when abandoned. Ordinarily, these natural cisterns are not thought of as sources of industrial water. Under special circumstance, if chemically treatable, they might become valuable industrial water reservoirs. An example of a group of about 20 mines in a geological and structural setting insuring water entrapment, rapid recharge and a possible minimum of contamination, are the small, compact Belle Ellen and Piper basins in Alabama's small but second most productive coalfield, the Cahaba. The mines have been abandoned from more than 50 to less than three years. The county now produces about a million tons of coal annually, all from strip mining. Figure 1 shows an idealized cross section of the strata in the Belle Ellen syncline near West Blocton, Bibb County, Alabama. Figure 2, 3 and 4 are maps showing the location of the syncline, other structural features, the outcrop lines of the three principal coalbeds underlying the basin, and the mined-out areas on the three beds (1).

Jan 1, 1973