Search Documents

By A. B. Cecala

An evaluation was recently performed on a district recirculation system at a trona mine in Granger, Wyoming. A 1.52m (5 ft) diameter, 37.3kw (50 hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated approximately 31.4 m'/sec (66,578 ft'/min) of air back into the intake. This amounted to a recirculation factor of approximately 20 pct of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 6l0m (2,000 ft) and 1,829m (6,000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane, and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF. tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1991

By R. J. Kolada

The ventilation systems of coal storage silos are normally capable of rapidly dispersing any accumulations of methane in the atmosphere above the coal pile surface. However, the results of an investigation which is presented in this report show that hazardous concentrations of methane can accumulate within the coal pile. Methane trapped within the coal pile is released into the atmosphere of the loading gallery when coal is discharged from a silo. If the methane released is of a flammable concentration it is necessary to ventilate the gallery to reduce the risk of an ignition. This report proposes a simple test, which, after further investigations may prove to be an effective method to calculate gallery ventilation requirements.

Jan 1, 1985

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By Frank Cook

As in other areas of the country, surface coal mine productivity in the Central Coal Province--primarily Illinois, Indiana, and west Kentucky--has declined steadily since 1969 (figure 1). Productivity, as measured in tons of clean coal produced per man-shift, dropped 35 percent during the period 1969-1975. Unwelcome at any time, this phenomenon is particularly untimely now, when increased coal production is a national goal. The U.S. Bureau of Mines has been working with the coal industry to develop new operating methods and equipment to enable increased productivity and improved reclamation performance in surface coal mining. Several projects have involved identification and evaluation of existing overburden handling and reclamation practices, and development of means to improve operational procedures. Some results of one of those projects, as they apply to the Central Coal Province, are summarized in this paper.

Jan 1, 1977

By J. F. T. Agapito

Significant economic benefits can result when rock mechanics is applied within a practical framework and integrated within the other engineering functions of the mine organization. This requires management support and understanding of rock mechanics as a practical tool to help attain high standards of safety, productivity and resource recovery. For such an approach, a long-term geotechnical program is needed in most operations to build an adequate data base and to ensure that design and ground control issues are handled in a cost-effective manner. This paper presents a summary of four case studies where significant economic benefits were realized with the help of rock mechanics. Although cost savings were not computed, the economic benefits are obvious and clearly impacted the mine operations favorably.

Jan 1, 1990

By S. H. Amini, A. Noble

"While many classic mineral processing circuit design approaches rely on deterministic methods, numerous studies have shown that the uncertainty inherent to the various input parameters can significantly influence design decisions. In a separation circuit, many of the technical uncertainties can be mathematically represented as statistical distributions for the unit recovery and feed grade. These uncertainties are then propagated by the circuit design and reflected in the circuit performance indicators, such as product grade and global recovery. An effective design strategy entails identifying which units are most influential in this uncertainty propagation and thus merit further consideration. Unfortunately, few analytical tools provide this information, particularly those that rely solely on deterministic methods. However, one promising approach is through the application of Taguchi’s method, in a fashion similar to statistical tolerancing of manufactured products. Since the technical challenges are fundamentally similar, Taguchi’s method shows promise in evaluating the level of compounded uncertainty by various circuit designs while determining the role of each separation stage on the overall selectivity and variability of separation circuits. This paper demonstrates Taguchi’s method in several two and three unit circuit designs. INTRODUCTION AND METHOD DESCRIPTION Uncertainty in Mineral Processing Circuit Design Analysis and estimation of uncertainty propagation in mineral processing separation circuits is an essential and significant aspect of an optimal circuit design procedure. Most of the current circuit design methodologies have been constructed, implemented, and validated using a deterministic modeling approach. However, numerous studies have shown that the inherent uncertainty induced by uncertain design parameters can be a significant factor in many mineral processing applications (e.g. Kraslawski 1989; Xiao and Vien 2003; Ghaffari et al. 2012). Thus, an effective circuit design methodology must be able to quantify uncertainty in separation circuits with limited input data. This paper describes Taguchi’s method, as an experimental design technique, to approximate uncertainty in mineral processing applications, and then the similarity of results between Taguchi’s method and Monte Carlo Simulation is investigated. Monte Carlo Simulation The term “Monte Carlo Simulation” has been used to refer to a variety of stochastic simulation methods spanning a broad array of business, technical, and scientific domains. Most generally, Monte Carlo Simulation refers to numerical analysis which is based on (pseudo) random sampling from a domain of input parameters with a known statistical distribution. This methodology allows one to determine the distribution of expected results from a standard deterministic process model. Execution of a Monte Carlo simulation begins by identifying the domain of input parameters, statistical distributions for each parameter, and a deterministic process model which describes the anticipated result as a function of the inputs. Next, one discrete random sample is taken for each input parameter, considering the input distributions. The process model is then solved for this mix of input parameters, producing a single simulation result. This procedure is then repeated a “large” number of times, utilizing new randomly sampled input parameters for each simulation iteration. Once the desired number of iterations is reached, the results of each independent simulation are aggregated to produce descriptive statistics such as minimum, maximum, mean, standard deviation, kurtosis, and other distribution parameters. Given enough iterations, the Monte Carlo method fully explores potential synergies between the input parameters. The methodology does not require the process model to be differentiable, continuous, or even analytically defined. While the number of required iterations varies in relation to th"

Jan 1, 2017

By B. Cavender

The operating lifetime, or production rate, selected for a mining project is among the most important factors influencing the project's design and ultimate economic success. Incorrectly-determined lifetimes can lead to the erroneous rejection of projects as uneconomic as well as the suboptimal exploitation of producing properties. This paper examines the optimal lifetime calculation using traditional discounted cash flow and recently-proposed option pricing techniques. Using each method, the production rate is determined as that rate at which the project's net present value is maximized.

Jan 1, 1993

By E. B. McNew, J. M. Barnes, A. E. Torma

The applicability of biosorbent materials for the removal of uranium and other heavy metals from synthetic and actual uranium mil 1 tailing (UMT) solutions has been investigated. The biosorbent materials used in this study were barium loaded beads of alginate, alginate-dextran sulfate, alginate-carrageenan, and alginate-xanthan gum. These studies were performed in stirred vessels and packed columns. It was observed that 100 percent of the uranium could be removed from a synthetic solution following 2 hours of contact time in a stirred vessel, and 80-100% of U, V, Mo, Mn, Sr, and Zn could be removed from a UMT effluent solution with a packed column. Kinetic evaluations were performed, using a generalized rate equation, on the biosorption of uranium with these barium loaded beads.

Jan 1, 1992

By G. C. Hambleton

There is sufficient indication of the existence of a basic misconception in the Coal Mining industry (on a world-wide basis) as to what computer control really does, what it costs, how it works and how and what it achieves as to make this presentation a welcome opportunity to present the case in what we hope is a simple, meaningful way. A plant cannot be said to be "automated" unless the control system has the capability to react automatically in accordance with predetermined programs under a great multiplicity of operational situations.

Jan 1, 1981

By D. W. Niosi

In this chapter, a review is made of the various stages of an exploration program, mineral rights acquisition methods and the partners involved in an agreement, the after- tax cash flow approach using present value discounting principles, the establishment of computerized financial models for assistance during the negotiating stages for a mineral property, and the various evaluation techniques and their specific applications during different phases of an exploration program. A set of examples is shown encompassing the initial target-seeking stages to the ultimate feasibility study stage.

Jan 1, 1979

By Judson G. Brown

In order to filter small amounts of fine slimy solids the reversible cake-filtration process was developed. The filterable solids contents lion in feeds can range from less than 1 ppm up to about 5%. The relative advantages of this process, are usually the greatest in the range of 0.05% to 1.0% filterable solids. Filterable solids that average in particle size about 20 microns& are non-compressible are very easy for this filtration process. Some feeds have been all sub-micron in particle size. A 1/8 inch thick cake is considered to be very thick. The usual cake is between 13/2 and 1/16 inch thick. A new line of injection molded plastic filter plates were developed for use with the reversible cake filtration process. The first commercial sized installation of this system was made 3 years ago in the Wakefield Y.M.C.A. swimming pool. Over 70 filters ranging in size from one plate to 63 plates have been produced. In addition to the process advantages there are the low cost and corrosion resistance advantages of the plastic plates.

Jan 1, 1962

By R. K. Singhal

In open pit mining every effort is made to maintain as steep a pit slope as possible. Pi t slope angles are influenced by numerous factors some natural that are amenable to limited or no control at all and other mining technology related where a greater degree of influence can be exerted by the engineer. One such area where control is possible is the method of drilling and blasting in the pit. This paper discusses the influence of blasting techniques on the economics of pit slopes and demonstrates how balanced blasting can be used with advantage to pit wall control and improve fragmentation (thus reducing material handling costs). Microprocessor based instrumentation to monitor drill and blast performance has also been described.

Jan 1, 1988

By A. F. Stewart

Slope design in an open pit mine includes the determination of a number of parameters, including bench height, bench face angle and berm width. By way of a case history of two highwall slopes (160m and 220m high) excavated in dipping strata in an operating coal mine, this paper illustrates the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in essentially the same lithologic and structural environment, with the main differences between the slopes being the angle at which the bench faces were excavated and the excavating methods that were employed. In addition to describing the instability that occurred on one of the pit walls, relevant aspects of the engineering geology, slope design and excavation procedures are described.

Jan 1, 1998

By D. W. Gillmore

Numerous orphaned strip mines and old refuse piles scar the landscape, contributing to stream pollution and degradation of the natural environment. Field experiments to reclaim acidic surface-mined spoil and refuse banks with fly ash from bituminous coal-fired powerplants were conducted at several sites in West Virginia. Fly ash served as a neutralizing agent and soil amendment, permitting vegetation of waste lands and disposal of large quantities of ash. Reclamation of land by this method is estimated to cost about $300 per acre of leveled site, depending upon the topography of the land and quality and availability of the fly ash.

Jan 1, 1972

By J. Chai, Q. Yuan, B. Qiu

"Overburden strata deformation monitoring is one of the key problems in ground control. Using geophysical method through surface drilling to detect strata deformation is commonly used in the industry. In this paper, a geophysical method based on the distributed optical fiber sensing (DOFS) system were conducted in the laboratory, where a DOFS-based strata deformation monitoring experiment was performed with three physical models. The results show that the DOFS method precisely detects the rock mass deformation and strata structure forming with the Brillouin frequency shifts (BFS) representation. The BFS curves are divided into three phases, which reflects the horizontal three zones developed in the overburden. The BFS distribution presents a multiple stages form, the 1st stage corresponds to the caving zone and the 2nd stage corresponds to the fracture zone. Based on the multiple stages form, the evolution of the water flowing through fractured zone have been determined and the controlling effect of key strata over the water flowing fracture has been pointed out. In the end, the comparison validation proves the accuracy and reliability of this method, and it could be a new approach for the ground control research. INTRODUCTION Overburden rock strata above the work face space will propagate from slight deformation, part destruction to violent movement because of the underground coal mining. It is fundamental and an intrinsic requirement of ground control to monitor the mining-induced rock mass deformation.[1] Overburden strata have their significant mechanical behaviors and movement under damage deformation and fracture. Overburden strata deformation affect the mining ground pressure control directly, and performance in the relationship of supporting equipment and the surrounding rock, the mining-induced fracture distribution and the loss of underground water resource, the ground surface structure stability and the ecological environment.[2] From the perspective of the concept of safe and efficient scientific coal mining: the overburden strata deformation is an important part of mining method selection and reasonable supporting solutions decision which can solve the issues like the roof supporting force calculation, overburden fracture distribution and gas drainage, ground subsidence, separation of coal and rock control and top-coal recovery rate and so on. From the perspective of green and ecological mining: the overburden strata deformation is the key basis of studying the mining-induced ground subsidence and mining area ecological damage, and such engineering problem like environmental protection in mining area, ecological restoration in mining subsided land and the water conservation in fragile ecology area of mining could be solved based on it.[3-6] Therefore, the mining-induced overburden strata deformation is the key of ground control and needs to be controlled artificially."

Jan 1, 2017

By Sean Hunter

Artificial Intelligence has a long history but is currently coming strongly into focus with new advancements. This leads to questions many people are asking: what exactly is AI, how can it be used effectively in mining operations, and what foundation is required to make AI implementations successful? In mining, many AI applications exist, from drill pattern optimization to predictive maintenance. However, many implementations struggle due to data integration challenges. Mining operations generate large amounts of data from many sources, such as fleet management systems, drill sensors, process control systems, and laboratory results. Unfortunately, this data often exists in silos where it’s difficult to get it out, making AI applications unable to leverage it. Worse still, tools that use AI don’t always provide their data back to the system, creating even further data silos. All these problems make it hard to take advantage of the data at the mine, slowing down and reducing the effectiveness of AI. This paper presents a comprehensive approach to organizing mining data using an AI-ready knowledge graph system. We will first explore the evolution of AI in mining, from early expert systems to modern machine learning applications. Then, we will detail how a knowledge graph can integrate business context, operational data, and AI models into a cohesive system that enables more effective AI implementations across mining operations. The proposed method has been developed considering both the unique data challenges faced by the mining industry, while also considering best practices learned from the AI field at large. By following this approach, it’s possible to better utilize existing data, getting higher quality and more complete results faster, and in a way that’s reusable and composable.

Feb 1, 2025

By Wen-Long Cai, A. Frederick Banfield

This paper investigates, through case studies on a porphyry copper and a coal deposit, the differences and relevances between an approximate production schedule approach, i.e., the best case and the worst case schedules and a practical production schedule approach. The comparisons were with regards to: 1) choosing an optimum ultimate pit size, 2) determining processing capacities, 3) selecting 'optimum' cutoff grades, and 4) blending. The comparison criteria was to maximize the project net present value. Conclusions were drawn based on the study results.

Jan 1, 1996

By Michael N. Maltezos

"There is certainly no argument that LED lighting systems have taken a strong foothold in the lighting marketplace over the last several years. This has even proven true in the world of transportation and transit lighting, for which new LED cobra head style luminaires are replacing traditional HID cobra head luminaires on North America’s roadwaysand linear LED light fixtures are replacing conventional linear fluorescent light fixtures in North American rail transit facilities. However, LED technology has taken a while longer to penetrate the very specific market of vehicular tunnel lighting in this continent. Though both the New York/New Jersey Holland and Lincoln Tunnels have recently been retrofitted with LED lighting, and an LED Lighting RFP is currently out for Boston’s Central Artery Tunnels, very few vehicular tunnels in North America to date have been illuminated with LED light fixtures. This is largely because cost effective LED lighting, that met our typically stringent tunnel lighting standards, was until recently simply unattainable. However, with the rapid advances in LED technology over recent years, owners and specifiers of North American tunnel lighting projects have finally begun to adopt LED lighting systems as the norm. In fact, a recent Lux Fit/Yole Development “LED in Road and Street Lighting Report” stated that “LED luminaire growth will be driven firstly by tunnel lighting, and then relayed into highway, road, residential and amenity lighting applications starting in 2014.” 1 Our highways are continually becoming more congested. As a result, Provincial and State Departments of Transportation (DOTs) are constantly looking for innovative ways to improve traffic flow. One way DOTs are now helping to ease congestion is by expanding the use of tunnels and long underpasses in large interchange reconstruction projects. With less available right-of-way to work with, and the high costs of maintaining elevated bridge structures over the years, it often makes more sense to “go under” (rather than over) the traffic congestion points. With the addition of these new tunnels and long underpasses comes the issue of proper illumination within these structures, for a safe and efficient driving task. DOTs use recommended lighting practices and guidelines for highway lighting, which include specific criteria for tunnels, set by either the Illuminating Engineering Society of North America (IESNA) or the American Association of State Highway and Transportation Officials (AASHTO). However, both IESNA and AASHTO point out that these recommended practices and guidelines are not a mandate, and DOTs are free to make their own decisions about lighting criteria. Accordingly, effectively illuminating tunnels is often times a challenge. This paper will examine the key considerations of the tunnel lighting application in generalas well as what LEDs now bring to the table and how, accordingly, traditional lighting technologies will be phased out in the future illumination of tunnels."

Jan 1, 2016

By R. S. Hearon

The image of the open-pit miner in the eyes or the Environmentalist has never been very outstanding. The phosphate industry, whose history in Florida reaches back to the late 1800's, can-not be credited until recently with a large number or accomplishments in terms of protection or the environment to change this image. This lack of action was not deliberate or in opposition with the desires of the public. In the formative years, there was little or no public and the companies found it necessary to build towns to house their employees and their families, towns which remained in existence until the late 50's and early 60's or formed the core of present large communities. Neither these pioneers nor most subsequent resource developers considered themselves un-thinking spoilers, nor were they so regarded by their contemporaries. Instead, they acted in a manner consistent with their environmental circumstances and intellectual heritage. Early Americans did make mistakes in using the land but the mistakes became apparent only in the opinion of later generations. Over the past five to ten years, there has been a new self-awareness in the industry with regard to environmental responsibilities brought about, in part by a continuing onslaught of new regulations with jurisdiction over our activities. Part of the new regulations are aimed at industries as a whole while many, particularly state regulations, pertain specifically to the phosphate mining industry. Why all the new regulations? The reasons are encased in a complex web of activity but stem primarily from a new public awareness of its environment. More and more of our youth have become interested in the environmental science areas such as biology and ecology. The tremendous growth rate in both the population and industry has made personal issues out of subjects such as atmospheric inversions and water shortages which previously were abstract concepts. The State has grown from a population of 1,500,000 in 1930 to approximately 9,000,000 people today. This personal impact and general lack of knowledge on the part of the public concerning economics has resulted in big business no longer being held in awe, often in contempt and generally in suspicion where environmental concerns are encountered.

Jan 1, 1978

By J. S. Chen

DOE recently funded 21 projects under the solicitation by its Environmental Restoration and Waste Management Division. This project is combining the expertise of an interdisciplinary team of researchers with that of three manufacturers to isolate nuclear waste storage sites using remote longwall mining. The concept is being pursued in Germany, too. This paper will present the conceptual approach to the project and discuss the problems in transferring longwall mining technology to nuclear waste containment.

Jan 1, 1994