Search Documents

By Wilson Blake

The occurrence of rock bursts in some deep mines throughout the world constitutes a severe operational hazard. In addition to endangering the safety of the miners, the rock-burst problem is a major factor in mining economically in deep mines because of the loss of production and expense owing to cleanup and repairs following a burst. Developing means of controlling or eliminating rock bursts has been the subject of intensive research for over 50 years. While much has been learned about the effects of rock bursts, little is known about their basic causes; hence, control measures have been at best only partially effective--attested to by the number and severity of bursts that continue to occur throughout the world each year. In the Coeur d'Alene mining district of north Idaho, the rock-burst problem continues as the silver and lead veins persist at depth. These veins are presently being mined at greater than 7,000 feet below the surface and will be mined to some 10,000 feet in the future. The majority of rock bursts in this district occur in pillars. While pillar bursting has been essentially eliminated in some deep-mining districts by longwall techniques, modification or application of this technique to the thin, irregular, and near vertically dipping veins of the Coeur d'Alene district has not been found to be practical. The creation of pillars is a consequence of the horizontal cut and fill mining method used. Figure 1 shows a vertical longitudinal projection of the silver vein at the Galena mine, illustrating the mining method. Stoping progresses between raises and is carried upward between levels. A horizontal pillar is created as a stope approaches a mined-out level. Recent broad-band micro seismic monitoring of rock-burst-prone stopes by the Bureau of Mines has shown that potential burst zones could be delineated weeks in advance of a burst and that a definite sequence of events took place prior to the occurrence of a pillar burst (1). Hence, time was available for control measures to be effected when a stope pillar reached a critical burst geometry.

Jan 1, 1971

By David L. Giles

The Lime Creek* ore body in northwestern British Columbia is one of the few commercial primary stockwork-type molybdenite deposits in North America. Others include the Climax, Urad-Henderson, Questa, and Endako ore bodies. They are mined on a low grade-high tonnage basis, and are open pit operations except for Climax and Urad-Henderson. Much recent geochemical research on both porphyry copper and stockwork MoS2 deposits has been concerned with dating of micas related to the mineralization and associated igneous rocks. The results appear to show that mineralization and the predominant magmatic events of the deposit are indistinguishable in age (1-5), except where dating has been in sufficient detail to resolve the analytical overlap (6). At Lime Creek, geologic information shows that the Main granodiorite, the major intrusive and dominant host rock for MoS2 mineralization, was emplaced and had solidified sometime prior to the introduction of MoS2. The first MoS2 episode is intimately related to localized bodies of kalialaskite which clearly intrude the older stock. K-Ar dating was undertaken to clarify the age relations between Lime Creek plutonism and the apparently younger hydrothermal event that began with kalialaskite.

Jan 1, 1975

By V. G. Medina

The 15 000 t/d La Coipa mine initiated operation in July of 1991. The complex consists of a conventional, open-pit mining operation and a mill employing cyanide leaching with Merrill-Crowe gold and silver recovery. The process plant includes a primary crushing circuit, a 15,000 t (live) covered stockpile, a semi-autogenous mill/ball mill/crusher or SABC grinding circuit, a leach circuit, a belt filtration/washing circuit, a zinc precipitation circuit and a "dry" tailing disposal system. The process plant is described in detail with major design considerations used in the selection of the processes and equipment. The unique methodology employed in the disposal of the filtered tailings is also described.

Jan 1, 1992

By Alexander Sutulov

1. INTRODUCTION According to the classical economic approach of the open market economy, copper supply should be regulated by market forces which are (a) demand and (b) prices. In fact, demand is of primordial importance because prices are a reflection of supply-demand balance: they go up in times of shortages of supply and down when over-supply situation exists. In the past few years, this basic mechanism of market economy has been under pressure from a number of non-market forces, such as social and monetary problems of sane important copper producing countries; structural changes in copper mining companies through mergers with oil companies; and other factors which greatly contributed to distortion of the basic supply-¬demand equation. As a result, we have faced in the last three years a situation of oversupply rarely seen in the past, with a catastrophic fall in copper prices, huge losses at mines and unprecedented indebtedness of copper producers. This has deep repercussions in the copper business and its future supply outlook. This is particularly so when taking into consideration that high indebtedness and high interest rates conspire against the very survival of some traditional producers. As we write this comment (July of 1985), close to one half of U.S. copper production capacity is closed down, sane of it for good, while the same precarious situation exists in Canada, Australia, Zambia, and some other primary producers who cannot face present low prices with equally low costs. The question is then what this situation means for the medium-¬term future, until the end of this decade, Particularly when taking into consideration the fact that some of the factors influencing it are of a long-term character. 2. SUPPLY-DEMAND SITUATION IN THE LAST FIVE YEARS Since the last boon year, in 1979, when world copper consumption reached a record of 9.8 million metric tons of refined copper, demand dropped to only 9.0 million tons in 1982, when the crisis bottomed out, and then steadily recovered to the level of 9.7 million tons in 1984. Meanwhile, copper production, which in 1979 was only 9.4 million tons, in spite of the fall in demand, grew to 9.7 million tons in 1981 and 1983 and only temporarily was cut to 9.4 million tons in 1982 and to 9.5 million tons in 1984. As a result of this imbalance, hugh copper stocks were accumulated with supply systematically out¬growing demand by over 2 million tons at one time. With the Western World refined copper demand running at an average of 115,000 tons per week, this oversupply was equivalent to between 15 and 18 weeks production, i.e. twice as large as normal. This was immediately reflected in very low copper prices. Another contributing factor to relatively low copper prices was the lack of speculator interest for this commodity. Between 1981 and 1984 the world experienced a very intensive period of wealth distribution, high interest rates and intensive restructuring off world economy and its industrial sector. Therefore, much of the available money was attracted to more lucrative and attractive investments rather than to the lack-luster performance of copper, and for that matter, of the metal sector in general. The much announced and discussed recovery of the U.S. economy since 1983, and particularly in 1984, with an overall growth of the GNP by 6.8% in 1984, happened to be more oriented to the service sector than the industrial sector and therefore this recovery was not adequately reflected in copper consumption nor to metals in general. This put serious doubts about the future demand for copper. Consequently copper prices failed to improve in spite of an apparent fall in stocks and a healthy increase in the demand for copper since 1982. At the time of this writing (July, 1985), although same analysts claim that the available stocks are running at about 8 weeks of supply, which are considered to be below normal, copper prices are still very low at between 65 and 67 cents per pound of copper. Part of the answer may be the normal seasonal slow-down period in the Northern Hemisphere due to summer vacations and

Jan 1, 1986

By Betty L. Gibbs

A short course, held during the SME Annual Meeting in Phoenix, AZ in February, focused on software for surface and underground mine modeling. The objectives of the short course were to review techniques for surface and underground mine planning. Mine planning software vendors were invited to demonstrate how their software runs, given a standard data set. Six vendors of mining-specific software participated in the workshop. They were Exploration Computer Services (MINEX 3D), GEMCOM Services, Inc. (PC-MINE), KJRA Systems (VULCAN), Mine Development Associates (SURPAC), Micromine and MINEsoft (TECHBASE). Data set A data set was created to challenge the capabilities of each vendor's software. The criteria used for the data set selection were: • a minimum of 300 drill holes; • the data must include topography, drill hole survey, assay and formation contacts; • the deposit was multimetallic; and • there was the potential to be mined by surface and underground methods. The data set used was an actual, complex copper ore body with a small amount of gold. The ore body was close enough to the surface to be mined by surface techniques. Part of it, though, was also amenable to underground mining. To further complicate the problem, a river ran across the area of the ore body. This presented mine planners with the problem of either moving the river or mining around or below it. The ore body had not been mined, so no data was available for the tons and grade actually produced. Data for the mine planning problem was distributed to each vendor about two months before the short course. They had the opportunity to load the data into their systems, build an ore body model and perform preliminary work. During the first day of the workshop, the vendors received problems concerning the ore body. They went to work on their machines, attempting to show short course participants how their software could help solve the problem.

Jan 1, 1992

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By F. A. Molloy

As a result of feasibility studies made in 1975 a 3-0 seismic reflection survey was shot over part of the Veendam salt pillow during 1978-1979. The Zechstein salt pillow, located in the northeast of the Netherlands near the town of veendam, occurs at a depth of 1400 m and contains three carnallite rich horizons over an interval of 300 m below top salt. MgCl2 brines are produced from these layers as feedstock for a magnesia plant, which starts up in 1981. Prior to the acquisition of the seismic data four wells had been drilled. The thickness of the carnallitite layers encountered in these wells varied between 50 and 125 meters. In view of these variations it was necessary to obtain a reliable isopach of the different layers. The 3-0 seismic survey covered an area of ± 4x4 km with a sampling interval of 20 m in all directions. The data was recorded it an area array using a 120 channel instrument. Final presentation of the data was in the form of 3-0 migrated acoustic impedance cross sections. The quality and resolution of the seismic data allowed reliable structural and isopach mans to be made. It was shown that the carnallitite layers are continuous over the area surveyed, whilst local thickening is "fault" related. Having this information brine production locations could be choosen in the thicker parts, allowing maximisation of production potential whilst avoiding faults and fulfilling mining regulations. A subsequent benefit of this approach is the possibility of using the seismic data to predict ore grade. Using the available wells as calibration points the acoustic impedance response of the seismic at the well was matched to the ore grade found. From these points a synthetic section was made with varying ore grades. Pre¬liminary results are encouraging and the liability of this predictive tool will be evaluated in the light of future drilling.

Jan 1, 1981

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method traditionally solves each mesh equation by an approximation during each iteration. Thus, it is interesting from both a theoretical and a computational viewpoint to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation that has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the solutions.

Jan 1, 1998

By Donald Crowell

Due to falling metal prices and depletion of ore reserves, lead-zinc mining in the Leadville, Colorado, area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Company and ASARCO with ASARCO being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Company of Salt Lake City in conjunction with the Central Engineering Department of ASARCO. The plant was constructed by Stearns-Roger Corporation. Construction began in the spring of 1970 and the plant went onstream in April, 1971. Flow sheets and equipment lists are attached. This paper will describe the flow sheet very briefly and discuss in more detail those aspects of the design which may be of interest, particularly the provisions for expanding the capacity of the plant.

Jan 1, 1972

By H. J. Brown

Pluess-Staufer (California) Inc. Lucerne Valley California operation is one of the largest producers of high brightness high purity fme grind limestone products in western North America. The San Bernardino Mountains area of southern California contains the largest high brightness, high purity limestone mining operations and undeveloped reserves in western North America (Fig. 1, Brown 1987). Combined annual production of high brightness limestone products from several operations is approximately 1.5 million tons, with an estimated gross value of $75 million dollars per year (Fig. 2). An additional 5.0 million tons of cement grade limestone is mined by several large cement producers in the nearby Mojave area (Brown, in press). The purpose of this paper is to summarize the geologic setting, genesis and mining of white, high purity crystalline limestone by Pluess-Staufer (California) Inc.

Jan 1, 1994

By V. Price

Abstract: Action of certain strains of bacteria has been implicated as a significant factor in the oxidation of ore deposits. Other bacteria are thought to be significant in the formation of syngenetic sedimentary ores and in supergene enrichment processes. A normal soil/ground-water regime provides all of the necessary pH and Eh conditions for several groups of bacteria which influence the sulfur cycle in nature. Limiting concentrations of nutrients such as sulfate ions can determine whether a particular microbial species is active at a given place. In the present study, ground water was analyzed from a mineralized area and from a presumed barren area. Trace metal content of the ground water gave no well defined clue as to the presence of a sulfide ore deposit. Sulfide producing bacteria (presumably sulfate users) were found in water from about 50% of wells sampled in the mineralized area and in about 30% of samples from the barren area. These bacteria are readily detected and may provide a useful tool for regional geochemical recon-naissance. Bacterially produced sulfide ions can remove metals such as copper and zinc from solution thus complicating the interpretation of hydrogeochemical prospecting.

Jan 1, 1972

By G. T. Austin

Every year the United States consumes millions of dollars worth of abrasive materials as blasting media. Entrained in either a gas or liquid stream or propelled by paddles or wheels, they are directed onto the surface of another material to modify that surface. The modifications to impacted surfaces include cleaning, cutting, deburring, etching, finishing, and peening. Blasting media can be either organic or mineral abrasive materials. Information and data presented are for only a portion of the mineral abrasives, they are; fused aluminum oxide, coal slag, copper slag, garnet, metallic shot and grit, nickel slag, olivine, silica sand, silicon carbide, and staurolite.

Jan 1, 1994

By Barnaby J. Watten, Sibrell. Philip L., Brian J. Vinci, Andrew E. Friedrich

We evaluated a new process for remediation of acid rock drainage (ARD). The process treats ARD with intermittently fluidized beds of granular limestone maintained within a continuous flow reactor pressurized with CO2. Tests were performed over a thirty day period at the Toby Creek mine drainage treatment plant, Elk County, Pennsylvania in cooperation with the Pennsylvania Department of Environmental Protection. Equipment performance was established at operating pressures of 0,34,82, and 117 kPa using an ARD flow of 227 L/min. The ARD had the following characteristics: pH, 3.1; temperature, 10 OC; dissolved oxygen, 6.4 mg/L; acidity, 260 mg/5; total iron, 21 mg/L; aluminum, 22 mg/L; manganese, 7.5 mg/L; and conductivity, 1400 uS/cm. In all cases tested, processed ARD was net alkaline with mean pH and alkalinities of 6.7 and 59 mg/L at a CO2 pressure of 0 kPa, 6.6 and 158 mg/L at 34 kPa, 7.4 and 240 mg/L at 82 kPa, and 7.4 and 290 mg/L at 117 kPa Processed ARD alkalinities were correlated to the settled bed depth (p<0.001) and CO2 pressure (p<0.001). Iron, aluminum, and manganese removal efficiencies of 96%, 99%, and 5%, respectively, were achieved with filtration following treatment. No indications of metal hydroxide precipitation or armoring of the limestone were observed. The surplus alkalinity established at 82 kPa was successful in treating an equivalent of 1136 L/min (fivefold dilution) of the combined three ARD streams entering the Toby Creek Plant. This side-stream capability provides savings in treatment unit scale as well as flexibility in treatment effect. The capability of the system to handle higher influent acidity was tested by elevating the acidity to 5000 mg/L with sulfuric acid. Net alkaline effluent was produced, indicating applicability of the process to highly acidic ARD.

Jan 1, 2000

By Elwyn H. King, Thomas R. Kuesel

I. CONCEPT MARTA&apos;s Peachtree Center Station is being mined out of hard rock, directly beneath Atlanta&apos;s central business district, with minimal surface disruption during construction. Its cost is competitive with that of a conventional cut-and-cover alternative owing to its design concept, which utilizes the rock as a primary structural and architectural material. II. PLANNING The station was originally planned for cut-and-cover construction. However, Peachtree Street is unusually narrow for a main business street (generally 78 feet (24 m) between building lines) and cut-and-cover construction would therefore be very disruptive to surface traffic and severely restrict access to adjacent buildings, including Peachtree Center, Atlanta&apos;s showcase business/commercial complex. (See Fig. 1.) Tunneling had been considered, but was initially thought [ ]

Jan 1, 1979

By J. D. Crone

Crone Geophysics Limited in co-operation with Newmont Exploration Limited has developed a ground Pulse electromagnetic method. This is the first unit in a planned integrated system of surface and borehole Pulse EM equipment. Newmont had previously developed an operational Pulse EM unit for use in areas of very high surface conductivity. The Newmont equipment was large, heavy apparatus that required motorized transport. It operated in the equivalent frequency spectrum of 10Hz to 2.5Hz. The basic aim of Crone Geophysics was to design a Pulse EM system more portable than Newmont&apos;s. We wanted to operate in all types of field conditions including heavily wooded and mountainous terrain areas. We also wanted to record the higher frequency information that is contained in the Pulse EM waveform. There are three reasons why we thought this high frequency information was important in survey applications: (1) Field tests conducted over massive sulphide bodies in the Arizona desert showed that the desert weathering process tended to break down the electrical contact between sulphide crystals. The net effect is to reduce the conductivity of a massive sulphide body, particularly narrow bodies or highly fractured sulphide zones. In order to detect such occurances the higher frequency information is essential. (2) We wanted to be able to detect occurances with sulphide content as low as 5% sulphides that are usually poor to moderate conductors. (3) We also wanted to be able to determine the presence and extent of surficial conductive formations and clay deposits since many airborne EM anomalies are caused by such bodies. If we have the capability of detecting and recognizing these formations we would be able to explain the airborne anomaly.

Jan 1, 1976

By S. Hodgson

The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 illustrates the reserves of the deposit.

Jan 1, 1988

By Keith S. Liddell

he selection of mill design parameters to suit the applica­tion requirements can result in quite different operating parame­ters for each generic type of application, even though the basic mechanical layout of the mills may remain similar. The selection of the type and size of grinding media is very important to efficient and cost-effective operation, and to ensuring that the milled product achieves the required properties. Accordingly, the grinding media selection is seen as an integral part of the mill design. Consideration of the requirement for classification is important in order to achieve the optimum mill and circuit performance. This can lead to the circuit feed not being classified for a steady feed with minimal slimes and a low size reduction ratio. Feed containing on-size particles would be deslimed by open circuit classification. Closed circuit classification is performed where the feed fluctuates. The rheological characteris­tics of the circuit feed slurry can have an influence on mill performance, and needs to be allowed for. A common misconception frequently encountered is the belief that "a mill is just a mill". This is not the case with stirred types of mills, since the operating parameters selected for the mill can have a large effect on the product characteristics. For example, horizontal shaft high speed stirred mills have a com­pletely different grinding action to vertical shaft low to medium speed stirred mills, which results in large differences between the surface area produced at a given product size (Liddell, 1986). Hence, it can be misleading to apply test results or design procedures obtained from one type of mill to other types for scale-up. The Metprotech stirred mill, as applied in the mining and minerals industries, is a low to medium speed vertical shaft mill. The basic design has been discussed previously (Liddell, 1989). Currently, the largest mills that have been manufactured have an installed power of 400 kW. The largest chamber volume at this power is 6000 litres, containing IO t of grinding media. It is intended that the installed power will increase up to lMW as applications requiring larger sizes arise.

Jan 1, 1995

By A. Pomianowski

A spectrophotometric study of xanthate solutions alone and their mixtures with equimolar amounts of alkyl trimethyl ammonium bromide (CnTAB) has established the additivity of ultraviolet spectra (190 - 400 my) for potassium ethyl xanthate (KEtX) and C12TAB. No obvious effect of C12TAB addition on the decomposition rate of KEtX was observed. The kinetics of collector abstraction by copper, nickel and sphalerite powders were studied in 10-5 - 10-3M solutions of KEtX alone and in equimolar mixtures of KEtX and C12TAB. Presence of C12TAB caused a 2 - 3 fold increase in the amounts of xanthate (equivalent to many monolayers) abstracted by copper and, nickel powders but had no effect on the abstraction of xanthate by unactivated sphalerite. The adsorption of C12TAB itself from the mixed solutions was very low, at most ore monolayer only, and was not influenced by the nature of the solid powder used. The results are interpreted in terms of molecular associations and synergistic action of xanthates and quaternary amines.

Jan 1, 1963

By Ralph J. Anctil, James E. Palmer

According to relatively recent estimates by the US Geological Survey and the US Bureau of Mines, there are more than 0.9 Tt (one trillion tons) of remaining identified coal resources in the seven major western US coal-producing states and about 200 Gt (220 billion tons) in the demonstrated reserve base. Considering coal&apos;s current national production level of 0.7 Gt/a (0.8 billion tpy), these US reserve and resource figures are reassuring. Given here is a preliminary analysis of geologic constraints and an estimate of their effects on mining and recoverability of western coal. Mining Constraints USGS and USBM coal figures incorporate only thickness and depth, and are "blind" to many other major geologic constraints on mining and recoverability. The most important of these geologic constraints include: • coal seams too thin or too thick for conventional mining methods; • coal seams that cannot be mined due to insufficient separation from underlying or overlying previously-mined beds; • unstable or otherwise unfavorable roof strata; • soft or heaving floor strata; • coal seams that are too lenticular or discontinuous for conventional mining methods; • coal seams in intensely faulted areas; • coal seams having high angles of dip precluding the use of conventional coal mining methods; • coal seams that cannot be mined due to proximity of water-bearing strata; and • coal quality problems such as excessive ash, sulfur, chlorine, or sodium. Coal Thickness Present USGS-USBM classification for reserve base includes bituminous coal beds more than 0.7 m (28 in.) thick and subbituminous beds more than 5 m (60 in.) thick to depths of 305 m (1,000 ft). Both of these thicknesses are less than the thicknesses now considered mineable in the western US. The lower limit for bituminous steam coal in deep mines is about 1.5 m (5 ft). For subbituminous coal, a thickness of at least 2.4 m (8 ft) is generally required. Accordingly, the Bureau of Mines reserve base includes many thinner coal seams that will not be mined in the foreseeable future. Within the Powder River Basin of Wyoming and Montana many seams-Wall, Upper Pawnee, Lower Pawnee, Cache, Manning-range in thickness from 7.6 m (25 ft) to more than 30 m (100 ft) and occur at depths to 305 m (1,000 ft). These have been included in the Bureau of Mines reserve base. However, the mining technology required to mine these thick seams does not now exist. It will require many years for development. The ultimate recoverability from these thick seams is unknown, but could be as low as 25%.

Jan 8, 1982

By J. H. Bassarear

Conventional crushing and grinding circuits are compared to semiautogenous circuits. Recent installations of each circuit are reviewed and seven methods of using autogenous or semi- autogenous techniques are described. Steel and power consmption data are reported and benefits of a dedicated digital computer are discussed.

Jan 1, 1981