Search Documents

By Siegmund Babendererde

Introduction Lyon, with 1.1 million inhabitants, is the third largest city in France after Paris and Marseille. It is a lively industrial centre. Lyon lies at the intersection of many transport routes and at the fluence of Rhone and Saone. Like all large cities, Lyon is attempting to alleviate inner city traffic problems by constructing a metro. Metro construction in Lyon began with tunnels built by cut and cover methods along the streets. Deep diaphram walls, which were back anchored and toed into imperveous strata, formed the excavation walls. It is a very economic and simple method. However during the construction period, it has the disavantage of strangling urban life for several years. It is therefore increasingly being replaced by subsurface tunnelling methods. As it was decided to build the metro tunnel between the Guillotiere and St. Jean stations, and thus cross under the Rhone and Saone, the client, Semaly, put the contract out for a competitive tender in which the general parameters were defined. Line, level and construction method were left to the contractor. There was an extensive examination of the tenders, during which reference projects from competitors in Japan were visited, as well as in Germany. Finally the consortium of Dragages, Campenon Bernard, Colas and Hochtief was awarded the contract to drive this tunnel section with an hydro-shield and an extruded steel fibre concrete lining, a Hochtief design.

Jan 1, 1987

By Ben E. Adams

The Duval Corporation Sierrita copper and molybdenum mining complex is located approximately twenty-three miles south of Tucson, Arizona. The original open pit mine, Esperanza, was put into operation in 1958 and utilized one tailings dam until the Sierrita operation began in 1970, and a second pond was started. Both tailings operations continued to be operated separate and independently of each other until 1977, when the Esperanza Mill was temporarily shut down, and the Esperanza Tailings Dam was retired from service. Except for short periods of use, no new tailings were put on the surface. With the reactivation of the Esperanza Mill in 1979, the Esperanza tailings were combined with the Sierrita Mill tailings and put on the Sierrita Dam, leaving the Esperanza Dam in a retired state.

Jan 1, 1984

By Paul Piercy

Bougainville Copper Limited operates a porphyry copper mine in Papua New Guinea. The waste dumps will contain 400 to 500 million tomes of rock at the end of nine life. The paper describes investigations carried out over a period of en years and highlights the problems associated with waste lump leaching in a tropical and seismic active region. Aspects discussed include mineralogy, chemical reaction, leaching rates, microbiological activity, dump stability, dump structures, effects of tropical conditions, seismic activity and topography.

Jan 1, 1981

By Joseph G. Selmeczi

Lime and limestone-based SO2 scrubbing processes have demonstrated reasonably good success in removing low concentrations of SO2 from flue gases. While most of the operating problems experienced in the early days of scrubbing have been worked out, problems usually increase and removal efficiency drops with increased amounts of SO2 present in the gas stream. In order to overcome these difficulties, yet still taking advantage of lime and limestone as the lowest cost neutralizing agents, a host of so-called double- alkali systems were developed. These processes take advantage of cations such as Na+ and NH4+ capable of forming highly water soluble bases or basic salts, such as hydroxide, carbonate or sulfite, which having been neutralized or acidified by the absorbed SO2 can be regenerated with a lower cost base such as lime.

Jan 1, 1974

By H. R. Bullis

Lupin is located on the shores of Contwoyto Lake at lat. 65° 48'N, Long. 111° 15'W and lies about 80 kilometers south of the Arctic Circle. Since start up in 1982 the mine has produced over 2.15 million ounces of gold from 6.66 million tonnes of ore grading 10.63 gm/tonne. Total remaining reserves at 1993 year end were 5.1 million tonnes at a grade of 9.11 gm/tonne (1.65 million ounces). This is sufficient for 7 -8 years at the present annual production rate of about 200,000 ounces. The Centre and West Zones of the deposit are open to depth. The deposit is in an Archean metaturbidite sequence of the Contwoyto Formation, which has been mapped as part of the Yellowknife Supergroup of supracrustal metasedimentary and metavolcanic rocks making up part of the Slave Geologic Province. These rocks have been subjected to regionar and contact metamorphism and to several phases of deformation. Six stages of Archean plutonism have been identified and all Archean rocks have been cut by Proterozoic diabase dyke swarms. Gold mineralization in the Lupin deposit is commonly fine grained and associated with pyrrhotite and arsenopyrite in amphibolitic banded iron formation. The gold-bearing portions of the host iron formations are characterized by the presence of multiple quartz veins and the pervasive replacement of grunerite by hornblende. In sparsely mineralized portions of the host iron formation, zoning of sulfides about quartz veins is clearly seen with the arsenopyrite halo being more restricted around the veins than the pyrrhotite halo. In well mineralized portions, quartz vein densities approach one vein per metre along strike. In these areas pyrrhotite distribution in the iron formation is more pervasive and the rock takes on the appearance of a banded sulphide rock.

Jan 1, 1995

By J. M. Ekenes, C. A. Caro

"New approaches that increase hydrometallurgical recovery from refractory minerals in below mill cutoff -grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyritebearing ore at Freeport-McMoRan’s mine in Morenci, AZ. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation. Introduction The Morenci ore deposit, located in eastern Arizona, has been mined for copper for 140 years. Mineralization in the Morenci district consists of sulfides and oxides. To process these ores, Morenci operates concentrator and leaching circuits. Leaching accounts for two-thirds of the copper produced in Morenci. More than one-half of this leaching-derived copper production comes from run-of-mine (ROM) stockpiles. The largest category of material moved in Morenci is destined for ROM stockpiles and waste dumps. Materials that are not economic to mill or leach are designated “waste.” However, this designation can change based on improvements in extraction technology and commodity prices. Chalcopyrite does not leach well due to its refractory nature. For predominant chalcopyrite mineralized ore, copper recovery during a typical leaching cycle may be as low as 5%. For this reason, chalcopyritedominant ores below mill cutoff grade have historically been classified as waste. By incorporating advanced leaching technology to improve metal recovery from previously leach-resistant ore types such as chalcopyrite, the Morenci Mine has been able to reclassify substantial amounts of this “waste” to “ore.” Process chemistry Chalcopyrite copper extraction is temperature, oxygen and ferric dependent. The temperature is achieved primarily by pyrite oxidation (Eq. (1)) and secondarily by oxidation of chalcopyrite itself (Eq. (2)). The regeneration of ferric in solution can be enhanced by providing the appropriate acid and oxygen levels according to Eq. (3). In the absence of microorganisms, this reaction is very slow."

Jan 1, 2015

By K. Sharman

Quintette Coal Limited (managed and 50% owned by Denison Mines Limited) operates an open pit coal mine located in northeastern British Columbia, in the foothills of the Rocky Mountains. (See Fig. l). Mining commenced in 1982. The mine currently produces 4.75 million tonnes of medium volatile bituminous coal per year from three pits (Mesa, Wolverine and Shikano), using a truck/ shovel operation. (See Fig. 2). Conveyors and trucks transport run-of-mine coal to the heavy media/froth flotation process plan t, where it is cleaned and loaded into rail cars for delivery to the Ridley Island port at Prince Rupert, British Columbia. All coal is sold to the Japanese steel industry under a long term contract. The coal seams mined at Quintette are contained in the Lower Cretaceous Gates Formation. Mineable seam thicknesses vary from 0.6 m to 10 m. The regional structure of the area is typical of foreland fold and thrust belts, with open to tight folds and imbricate thrust faulting. The range of structural features found in the three pits, and their effect on mining, forms the subject of this paper.

Jan 1, 1991

By Robert J. Willard

In its search for additional ways to increase understanding of rock behavior, the Twin Cities Mining Research Center has turned to the scanning electron microscope, an instrument rapidly finding application in research concerned with surfaces of materials. Since features indicative of the manner in which rocks fail may be recorded on the surfaces of fragments as disintegration proceeds, this microscope might be used as a tool for seeking and mapping these minute features. In pursuit of such features, we chose to scan a portion of the fracture surface from a quartzite disk compressively loaded to failure between two pins centered along the disk's axis. The resultant fracture appeared as a rough, diametric plane, and the fracture surface near one of the loading points was scanned with the microscope.

Jan 1, 1969

By Bo-Hyun Kim, Mark K. Larson

"Bumps remain a critical safety concern in underground coal mining, despite significant advancements in engineering controls. These events occur when relatively high stresses in a coal pillar in conjunction with low confinement exceed the pillar’s critical capacity, causing the pillar to rupture without warning. Floor failure often occurs and can be an indicator of bump risk, as it is strongly associated with brittle failure known as spalling under a lower confinement. Significant floor heave at a western U.S. coal mine has been observed where the pillar width in a three-entry gate road system was 53 m, while no significant floor heave was observed where the pillar width in another gate road system was 22 m. This phenomenon was widely reported in the region and at another mine in another western coal field it has been reported that larger pillars are always associated with floor heave. In this study, a spalling model based on the S-Shaped brittle failure criterion and associated with the anisotropic characteristics of the materials was used in FLAC3D. The observed floor heave phenomenon associated with the larger pillars was demonstrated using this modeling approach.INTRODUCTIONFloor failure in a coal mines often inhibits longwall mining operation, as large displacement of floor strata, known as floor heave, interferes with travel, access, ventilation, and equipment operation. Aggson (USBM 1978) investigated floor heave in West Virginia where underclay is relatively strong and high horizontal stress is present. It was reported that the failure mode is mainly by buckling rather than by plastic flow.This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock mass behavior in longwall coal mines in highly stressed, bump-prone ground. More specifically, this study attempts to explain through numerical models small energy releases in the form of floor heave. The authors believe that brittle rock failure is associated with both floor heave and some bump mechanisms, if not directly involved in their cause."

Jan 1, 2019

By Rudecindo S. Silo

[The principal characteristics of the process is that when applied in medium or in great degree it only needs unelaborated raw materials such as sodium chloride and calcium carbonate, or of medium elaboration, as sulphur which is found in large quantity in the North of Chili; however, the may be also applied to small copper plants provided that low cost sulphuric acid is available as a substitute for sulphur, that is, in. those plats of small capacity where large additional installations are not needed for the regeneration of the leaching solution. The method itself comprises 6 stages, namely: crushing, leaching, washing; of solutions, precipitation, regeneration of the leaching solution and fusion.]

Jan 1, 1965

By Marshall D. Himes

The Pima mine, 39,000 ton per day copper mine, is located 17 miles south of Tucson, Arizona. The mine is in a sequence of Paelozoic and Mesozoic sediments striking east-northeast and dipping southeasterly intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian(?) dolo¬mites, limestones, and sandstones have been altered to talc-silicate skarn, marble and quartzite. The overlying Mesozoic Triassic(?) clastic sediments have undergone some recrystallization and hydro¬thermal alteration. The clastic metasediments are divided into three distinct lithologic units, lithic arenite, arkose, and inter¬bedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar and quartz, with or without sericite and chlorite). The porphyry has undergone potassic alteration. Dominant structures are an east-west post mineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. Two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast and the other striking northeast, dipping northwest. Mineralization is predominantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are lens important amounts of magnetite, hematite, sphalerite, galena, tennantite and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1972

By Werner Wenzel

Whisker growth during the reduction of iron ores The phenomenon of whisker growth can be observed in a number of solid-state crystallisation reactions, which, apparently, appear in6 the first instance as though they are two independent processes. From such reactions, one can find the whisker type of crystallisation on solid bodies. These examples show, that the whisker growth is neither due to certain crystal forms with predetermined temperature and pressureranges, nor to parameters, which, ad hoc, are necessary for the crystallisation. In all cases the whisker formation seems to depend on nucleation and the availability of crystallizing material in direct environment of such a nucleus, under given parameters of a system. One can generally state, that the research of whisker growth with the aim of establishing proper physical laws, to determine the foundamentals of whisker formation and whisker growth, is at present under active study. We can conclude that, although a great number of hypothesis have been proposed; no concluding theory has yet been arrived at. In the institute for ferrous metallurgy of the technical university of Aachen, research works are undertaken to find an explination to various metallurgical phenomena through help of whisker growth which was observed under varying conditions of iron ore reduction. This was possible by using refined microscopic techniques through which the whisker growth on solid oxyde substrates is detected. This refined technique combines the latest methods of surface examination with the help of stereo-scan-electron-microscope and proper and carefull preparation of surface to be stereo-scanned.

Jan 1, 1971

By David H. Dahlem

Uranium is a very mobile element geochemically and is widely dispersed in the lithosphere and hydrosphere. Under oxidizing conditions, it is particularly widespread and appears in all parts of the surface hydrologic system. As a result, this system is a leading candidate in uranium-resource assessments as a new base from which total resources might be estimated. No other sampling system provides the large volume geochemical capture as the continental hydrosphere and is as pervasive and non-selective regardless of rock type. However, the water system as a uranium metal sampler is not without drawbacks as the development of a National sampling program based on it has shown, In spring 1973, the National Uranium Resource Evaluation (NURE) was announced by the U. S. Atomic Energy Commission (AEC). The program was conceived to provide an evaluation of the domestic uranium resources and to identify areas favorable for uranium exploration. The specific NURE objectives are as follows (Bowyer, 1974): 1. To provide a preliminary evaluation of domestic resources and favorable exploration areas by early 1976, based on existing data. 2. To conduct a comprehensive evaluation of domestic resources and favorable areas by 1980, based on advanced state-of-the-art information. 3. To conduct an R&D program into new and improved procedures, equipment, and technology for uranium exploration and assessment. 4. To disseminate information on new exploration concepts and technology.

Jan 1, 1976

By Michael Drozd

Introduction Flotation is a recovery process that utilizes natural or chemically-introduced hydrophobicity of minerals to separate ore from gangue by attaching the ore particles to bubbles. Flotation has been known since 1906, when it was patented by E. L. Sulman, H. G. K. Pickard and John Ballot. Flotation's first documented plant use was in 1911, when it was used on gravity tailings from a zinc plant. Cyanide leaching was first patented in 1887. Most early precious metals flotation was linked to lead or copper concentrates. Most precious metal flotation is linked to sulfide recovery and utilizes such reagents as xanthates, dithiophosphates and thiocarbanilides. But the involvement of flotation in precious metals recovery does not have to be limited to active flotation of the gold and silver bearing minerals. Flotation can be used to remove interfering minerals, such as carbon, or cyanicides, such as copper, arsenic bearing minerals or other cyanide complexing minerals. Cyanide Leaching The use of cyanide to recover precious metals is the backbone of the industry. The various recovery processes that use cyanide are: 1. Leaching-Counter Current Decantation(CCD) Merrill-Crowe 2. Carbon-in-pulp (CIP) 3. Carbon-in-leach (CIL) 4. Vat leaching 5. Heap leaching These processes are selected depending on ore grade, ore leaching characteristics, reserve size and capital limitations. Ore grade is used as the first criteria to determine the type of cyanide plant required. However, the reserve size can determine whether a ground ore alternative is used. The ore leaching characteristics may indicate that the higher recovery, associated with a process that employs grinding, is the only economic recovery alternative. There are some extremely large leaching plants with grades that would be non-economic for some existing heap leach plants. Many factors, such as strip ratios, metal recovery and reserve size, determine what the ultimate plant design will be. The exact processing scheme that is used, is a multifaceted decision matrix, which gives the process metallurgist some job security. Precious Metal Recovery Using Flotation Flotation recovery can conceivably be used on any ore that has been ground. Many operations utilize gravity separation on the ore to remove native gold from the ore prior to sending it to cyanide leaching. On certain ores, where the gold is in visible nuggets or particles, this processing alternative is advantageous because the native gold cyanide recovery is

Jan 1, 1993

By R. M. Campoy

Mexico's mineral wealth has long been recognised and indeed has played a historically significant role on a world scale. The dynamics of the Mexican mineral industry have experienced a dramatic transformation especially over the last two decades. This transformation has mainly been instigated by the high growth rates and industrialisation of the Mexican economy since the 1960's. This paper focuses on the base metals sector of the industry which represents one of the major contributors to this transformation. The objective is to present a brief base metals review and to discuss some recent occurrences which pertain to this sector of the industry. This is followed by a discussion of mining's relevance in the current economic situation in Mexico. With this overview as background, the investment climate, primarily from a domestic investor's perspective and secondly in terms of foreign investment, is discussed. Finally, some recent government initiatives, including tax and accounting changes, are outlined. Any one of the sections of this paper can easily be developed into an extensive and indepth analysis; however, the intention of this paper is to provide the reader with a broad overview of the topics discussed.

Jan 1, 1985

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains (CAC) on roof bolting machines have been proven, through laboratory and field investigations, to protect miners from respirable dust, preventing dust overexposures. Another desired application is to develop a CAC that is mounted in the compartment of a shuttle car to protect the operator from dust. The challenges faced with this design include mine ventilation rates in tandem with the shuttle car tram speeds, causing cab airspeeds that may exceed 600 fpm, as found in this study of a central Appalachian underground coal mine. Prior research and laboratory testing indicate that successfully protecting a miner in high air velocities is difficult to achieve because the clean air from the CAC is unable to penetrate through the high velocity mine air and make it to the breathing zone of the operator. During this investigation by researchers from the National Institute for Occupational Safety and Health (NIOSH), dust concentrations of the shuttle car operator were measured. Also, air velocities experienced by the operator were measured using a recording vane anemometer. Results from the survey indicate that the highest exposure to respirable dust (2.22 mg/m3) occurred when the shuttle car was loading at the continuous miner, where there was an average airspeed of 157 fpm. While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 203 fpm. This study indicates that a CAC system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, since the majority of the operator’s dust exposure occurs in air velocities less than 200 fpm. INTRODUCTION NIOSH has issued a contract (#200-2015-63485) with Marshall University and J.H. Fletcher & Co. (Salem et al., 2016) to develop a canopy air curtain (CAC) for coal mine shuttle cars. The proposed design maintains a similar design to the roof bolter CAC by providing filtered air via a blower over the operator. The plenum, which will provide the uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a CAC is ventilation airflow perpendicular to the plenum airflow [Engel et al. 1987]. This ventilation airflow, if the velocity is significantly high, can shear the downward flow from the plenum. The shear caused by the ventilating airflow can reduce the effectiveness of the CAC by either disrupting the downward flow or allowing contaminated mine air into the CAC zone of protection."

Jan 1, 2018

By H. V. Scotland III

Lafarge Corporation's Texas Quarry, in Baltimore MD, achieved a substantial expansion of pit reserves by removing an inactive underground mine. The day lighting program, designed, and completed in 1997, open pit mined more than 400 meters of room and pillar workings which were originally developed to recover high brightness Calcium Carbonate. The project proved to be a challenge throughout its course as the pit plan was modified and successful daylighting techniques were developed to remove the mine without adversely affecting the safety of the operation, quality of the stone recovered, or negatively impacting the surrounding community. The design parameters and techniques developed and implemented at Texas may prove of interest to other operators as they are faced with daylighting opportunities. This article will detail the challenges we faced and the solutions which made the project a success.

Jan 1, 1999

By F. C. Townsend

Centrifugal modeling was used to evaluate reclamation schemes of; (a) flocculants, (b) sand/clay mixes, (c) flocculants/sand addition and (d) capping with sand or sand/clay mix. Results suggest the hierarchy of effectiveness is: (d) capping, (b) s/c mixes, (c) flocculants/sand addition and (a) flocculants. Comparisions between currently used large strain consolidation computer programs reveal no difference between piecewise linear or finite strain calculations. Correlations between numerical and centrifugal model predictions reveal excellent agreement on magnitudes; however, rate predictions require improvement in laboratory input data and centrifugal scaling relationships.

Jan 1, 1987

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. To develop the model of the ventilation system with the fire in this validation study, the following adjustments were made: (1) flow and gas distribution in the entire ventilation network, and (2) fire parameters matching the data recorded by the monitoring system. After close correlations between simulation and real data were achieved, additional analysis of the ventilation system with the mine fire was performed. Presented and discussed in this paper are the following stages of the fire at the Pattiki Mine: (1) early fire (before the fire was detected), (2) preparation for and fire fighting with water, (3) fire sealing, and (4) fire extinguishing. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By P. S. Newall

As part of a much larger research project, factor analysis was employed to help interpret and compare the geochemical signatures produced by two different sample media; a traditional -80# soil fraction, and a coarse float. Both sample types were collected by hand auger from the extension zone of the Redmoor sheeted-vein complex and analyzed -for 19 major and trace elements. The rationale behind the study infers that the geochemical anomalies produced by wallrock alteration around such targets can be better detected in the lithogeochemical rather than the soil environment, sometimes at considerable distance from their source.

Jan 1, 1991