Search Documents

By Paul R. Wieber

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification, he potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification independent studies show this process to be 25Z cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the lost advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average pro¬duction rates of 5.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds.

Jan 1, 1977

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By U. Schoepf

Economic and at the same time environmentally acceptable mining of small vertical ore bodies and veins to great depths has always been a challenge for miners. The Bauer cutter system, widely used in civil engineering, has been further developed for applications in exploration and mining, to a sustainable system for selective mining with a focus on small vertical ore bodies and veins, as well as residual ore in open pit operations. Current situation of conventional mining of small ore bodies and vertical veins Small ore bodies and vertical or near-vertical ore veins often pose a challenge to the mining industry. The relatively small size of the ore deposit over great depths or lengths, with only limited exposure to the surface makes economical mining difficult. Open pit mining of such ore bodies must either be terminated early because of the high stripping ratio and the enormous environmental impact or is unprofitable from the very beginning. The required massive stripping of waste rock leads to high material hauling times and costs, intensive roadway and bench construction and maintenance, possible safety hazards due to heavy vehicle movement, pit wall stability risks, intensive surface water management and massive waste dump requirements. In addition, it can be assumed that increasingly extensive rehabilitation measures will be required in the future after mine closure. Particularly in vertically oriented magmatic and hydrothermal deposits the technical, economic and environmental limits for further pushbacks, to extend the open pit depth, can lead to an early end of mine life even if a significant quantity of residual ore is left behind. Going underground is only a viable option in a limited number of mines with very high ore values and volumes. The high development cost of an underground mine, as well as the higher underground mining costs, often prevent further mining to greater depths.

Feb 1, 2023

By Krawiec Alfons

The threat of rock bursts along with the danger from methane gas and coal dust explosions belongs to particularly dangerous phenomena in Polish pit-coal mines. This phenomenon results mainly from the physical-mechanical properties of the rock mass as well as the geological-tectonic structure of the Upper Silesian Coal Basin. In the postwar years in Polish coal mining thanks to a multi- directional activity, a decrease of rock bursts and their effects has been noted. For example, the number of rock bursts reported in 1965 amounted to 71 in comparison to only 23 in 1974. The ratio of rock bursts calculated for 100,000 tons of coal extracted from rock bursting strata amounted to 0.08 in 1965; however, in 1974 it amounted to 0.023 /Fig. 1/. These results were obtained in face of a continually growing potential threat from rock bursts caused by the systematic increase of extraction from rock bursting strata, exploitation at gradually greater depths along with the extension of exploitation into deposits enclosed in different types of pillars and other parts of deposits surrounded by workings. Despite the achievements of science and mining practice in this field, this threat has not yet been fully studied and controlled as it should be, As a result, research on preventing rock bursts is being continually widened in Poland. This research has a complex, multi-staged and long-range character. Theory, laboratory and field work in the mines are working on a solution to the problem.

Jan 1, 1976

By George H. Davis

Much concern has been expressed recently as to whether water supplies will be sufficient to support accelerated energy development foreseen in operation Independence. Taking the Nation as a whole, sufficient water is available for energy growth, but locally, as in arid parts of the Colorado Basin, limited water supplies will dictate economies in water use and affect plant siting. As Young and Thompson1 point out with respect to electric power generation, the term "water requirements" is misleading, as demand for water for cooling is sensitive to price of water and thus is quite flexible rather than the inflexible or fixed level implied by the word "requirement." Much the same is true of other energy conversion systems. Water is used in many aspects of energy production including mining and reclamation of mined lands, on-site processing, transportation, refining, and conversion to other forms of energy. In the East, South, Midwest, and along the seacoasts, water supplies are generally adequate for energy industries; most water problems in those regions relate to pollution rather than supply. West of about the 100th meridian, however, runoff is generally less than potential diversions and energy industries must compete with alternative uses for the limited available water supplies. Water is especially short in areas of less than 10 inches mean annual rainfall where natural precipitation generally is insufficient for establishing vegetation without irrigation. Extraction. The principal categories of extraction comprise coal mining, oil and gas production, uranium mining, and oil shale mining.

Jan 1, 1974

By J. M. Rebstock

Recent re-classification of crystalline silica as a potential human carcinogen has resulted in a new limit of 0.1% free silica in bulk powdered minerals. Detection of silica at this level can be expected to severely challenge or exceed the capabilities of existing protocols for x-ray diffraction, the traditional method for free silica determination. Automated SEH-EOS analysis provides an attractive alternative method, with direct analysis of individual particles for the determination of the concentration of free silica, and a direct measurement of silica particle sizes. This paper will discuss automated SEH analytical procedures, sample preparation, and statistical considerations.

Jan 1, 1990

By N. F. Sather

Results of comprehensive trace element analyses of samples of Illinois #5 and #6 seam coals and the unquenched ashes obtained from gasification of these coals in a Lurgi reactor are reported and discussed. Areas where additional background information is needed for assessment of the environmental impact of trace element emissions from coal gasification are identified.

Jan 1, 1976

By Zibo An, Yong Hu, Hao Zhang, Hong Cao, Jun Xue, Zhen Luo

Phosphogypsum (PG) is a by-product of solid waste produced by the phosphate chemical industry. Owing to large emissions and massive storage issues, it causes a potential threat to our environment. Hereby, a method based on the precipitation and crystallization properties of calcium phosphate-magnesium ammonium phosphate (CP-MAP) followed by its adsorption on active solid waste powder is used as the main principle to treat PG harmlessly. The treatment process and its influencing factors for orthogonal experiments along with the associated environmental safety have been studied in detail. The results showed that this method could simultaneously remove soluble phosphorus and soluble fluorine from PG. When ACP, FA, HBM, and Ur were added to PG at a dosage of 3%, 13.5%, 0.04%, and 0.04%, respectively, the residual phosphate and fluoride contents was 0.061 mg/L and 0.856 mg/L respectively in the PG leaching solution. Compared to state-of-the-art approaches, this method exhibited higher efficiency in removing phosphate and fluoride. Most importantly, this method does not cause any secondary pollution in the process, thereby showing a novel application in large-scale industrial treatment.

Aug 29, 2022

By K. A. Foo

Minproc Resources Inc. is developing a tailings retreatment project in Bolivia at the Colquiri zinc-tin-silver mine, in the Bolivian Andes. Mining at Colquiri has been continuous since 1940 and COMIBOL, the Bolivian state mining company, has owned and operated the underground mine since 1964. There are 10 million tonnes of tailings at Colquiri containing 0.51% Sn, 4.21% Zn and 50 g/t Ag. Minproc plans to mine and concentrate the tailings at 1.15 million tonnes per year to produce feed for pyrometallurgical upgrading. The tailings are moderately complex, with cassiterite grain size ranging from 200 to 5 pm. The marmatite (ZnFeS) in the tailings is relatively easily recovered, with zinc recovery of 80% to a 40%-45% Zn concentrate. The major problem with the zinc metallurgy is that the marmatite is complexed with iron, which results in iron contents of 14%-17% Fe in concentrate. This makes the product very difficult to sell because of the low Zn:Fe ratio. Most zinc smelters require a Zn:Fe ratio of 6:1 or 7:1, whereas this concentrate has a 3:1 ratio. Concentrate sale terms are therefore unfavorable, and the high cost of transportation from Bolivia to the smelters is an additional burden.

Jan 1, 1992

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984

By Jeremy Cawley, Jeff Murphy, Horry Parker, Brock Gaspar, Jake Keegan

The Lower Olentangy Tunnel project includes 47,000 cubic yards of planned ground improvement for earth pressure balance machine (EPBM) tunneling (5.2 km) and microtunneling (335 m) in glacial soils. Jet grouting started in late 2021 and will continue through 2023 to complete operations at 5 shafts, 14 safe havens, 5 watermain ground improvement zones, and a river crossing. Typical jet grout columns are installed at depths between 15–24 meters. Discrete soil-cement blocks range from 267–8,900 cubic yards in volume. This paper discusses the methodology, testing, and technical considerations associated with jet grouting operations in glacial overburden across an urban environment.

Jun 13, 2023

By D. I. Hoyer

A preliminary model has been developed for autogenous pebble milling using information obtained from studies on ball milling and SAG milling. The model treats the breakage as the weighted sum of first-order breakage of smaller particles by tumbling pebbles, non-first order breakage of larger particles which are too large to be nipped properly by pebbles, autogenouS fracture and chipping of larger lumps to form pebbles, and autogenous fracture and abrasion of pebbles. The model includes the effects of residence time distribution, classification through the exit grate, and a mass transfer relation which describes the accumulation of fine material in the mill. Example simulations are given, based on breakage parameters determined from batch grinding tests in laboratory mills. fracture breakage and abrasion. In the development of these preliminary mass balance equations it will be assumed that breakage by fracture is first-order, but this assumption will be modified later in the paper. It will also be assumed that the residence time distribution of a long autogenous mill can be described by an equivalent series of m fully-mixed mills, with a classification action imposed on the mill contents by the discharge grate. Size distributions are expressed as a v2 geometric series, numbered 1 for the top size down to n for the fines, or "sink" interval. If the holdup in the mill is W then the rate of breakage of material in size interval i is given by SiwiW, where wi is the fraction of material in size interval i, and Si is -the overall specific breakage rate of size i material (fraction per unit time).

Jan 1, 1985

By James D. Piper

In the summer of 1957,9 the University of California sponsored a World Conference on Prestressed Concrete in San Francisco to which were invited a number of Soviet engineers. While attending the conference, these engineers in turn asked the University to form a delegation of American engineers to visit the Soviet Union the following year for the purpose of studying Soviet advances in concrete technology. A six man delegation was formed, and the dates of the Russian tour fixed for May 10th through May 21st, 1958. Before arriving in the Soviet Union, the American Delegation attended the Third International Congress on Prestressed Concrete in Berlin. While there, we noticed that the delegation from the U. S. S. R. used displays and showed motion pictures of many construction projects which we later were shown in Moscow. Our delegation left East Berlin by Russian aircraft on May 11th, and arrived in Moscow that afternoon. We were met by our Russian engineer hosts from The Academy of Construction' and Architecture who made all subsequent arrangements for our itinerary. This Academy has no counterpart in the United States. It. does 40 per cent of all engineering-and scientific work in the building construction field and coordinates 60 per cent of that done by other Soviet agencies. Due to the prestige of the Academy in Russian affairs, our delegation was able to obtain a surprisingly broad picture of construction activities in Moscow and Leningrad in just ten days time

Jan 1, 1960

By Richard H. Johnson

White Pine Copper Company, a subsidiary of Copper Range Company located in Michigan's Upper Peninsula, mines a Precambrian sedimentary deposit containing finely disseminated chalcocite, native cop- per and native silver. Silver occurs predominately in certain strata and presently provides a mill head averaging 0.25 ounces per ton. This technical publication traces the development of silver recovery at White Fine beginning in early 1961. White Pine refined copper contains an excess of silver over and above that required to impart Lake Copper properties. The copper does not require electrolytic refining to meet industry purity requirements, nor is there sufficient silver to justify electrolysis.

Jan 1, 1970

By L. Yan, D. Yantek

Federal regulations require refuge alternatives in underground coal mines to sustain life for 96 h while maintaining an apparent temperature below 35 °C (95 °F). Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat and humidity buildup is a major concern with refuge alternatives because they have limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding a refuge alternative is complex and not easily defined, analytically or experimentally. To investigate heat and humidity buildup in refuge alternatives, NIOSH conducted multiple in-mine, 96-h tests on a 10-person tent-type refuge alternative, a 23-person tent-type refuge alternative and a six-person metal-type refuge alternative. The results show that when moisture was introduced to represent perspiration and respiration from miners (wet tests), the average temperature at midheight increased by 10.5 °C (18.9 °F) and the RH approached 88 percent for the 10-person tent-type refuge alternative; the average temperature at midheight increased by 9.4 °C (16.9 °F) and the RH approached 94 percent for the 23-person tent-type refuge alternative; and the average temperature at midheight increased by 7.7 °C (13.9 °F) and the RH approached 95 percent for the sixperson metal-type refuge alternative. For the dry tests, where no moisture was introduced, the average internal temperature increased by 12.6 °C (22.7 °F) for the 10-person tent-type refuge alternative, by 10.3 °C (18.5 °F) for the 23-person tent-type refuge alternative and by 8.4 °C (15.1 °F) for the six-person metal-type refuge alternative. These results may provide refuge alternative manufacturers and mine operators with guidelines and considerations for evaluating temperature profiles for portable refuge alternatives. The information may then be used to make decisions on occupancy ratings and heat mitigation strategies based on the thermal environment in which the refuge alternatives will be installed.

Jan 10, 2018

By James M. Link

The transportation of solids by slurry pipeline is a rapidly growing field. Although early patents date from the latter part of the nineteenth century, it has only been within the last twenty years that successful long distance slurry transport lines have come into their own. The pioneering efforts in this country include the gilsonite slurry pipeline from Bonanza, Utah, to Grand Junction, Colorado, and the coal slurry pipeline from Cadiz to Cleveland, Ohio. Both of these lines were constructed in 1957 and had a combined annual capacity of about 360 million ton miles. Although the Cadiz pipeline was mothballed in the early 1960's, the interest in slurry transport systems continues to increase and one engineering and construction company is predicting that by 1980 an annual slurry system rate of more than eight billion ton miles will be achieved. The design and construction of cross-country pipelines for fluids such as crude oil appears relatively simple when contrasted against the complex problems encountered in slurry systems. Considerable effort has been expended in hydraulic research laboratories in an attempt to improve our understanding of slurry behavior. This effort has been rewarded with considerable success and is best illustrated by the large number of slurry systems now planned or under construction. However, slurry transport in pipelines is still, in many instance more of an art than a science. In order to minimize the risk factors in the construction and operation of large scale slurry systems, studies are frequently conducted in pilot scale test

Jan 1, 1972

By Adam Bedell, Brad Crenshaw

Tunnel project contract documents often present groundwater infiltration requirements for components of the underground portions of the project. All too often these documents require quantifiable target inflows for these components, but only refer to them in subjective terms such as “dry,” “manageable,” etc. The Contractor’s definition of these terms will inevitably differ from the Engineer’s definition of these terms. The purpose of this paper is to look at common subjective terms used in documents and provide suggestions for reasonable quantifiable language. Additionally, the paper will provide information and recommendations on relative levels of cost and effort increase needed to provide increasing levels of water cutoff (i.e., achieve “dryness”?).

Dec 1, 2022

By Matthew Holden, Jason Emery, Matthew Benjamin, Peter Craig

Over the last 25 years, through adversity and a growing level of risk mitigation, Australian Longwall mines have been using higher and higher capacity cable bolts for secondary support. A recent survey revealed 85% of Australian longwall cable bolts are a 70 tonne capacity pre-tensioned hollow post groutable system. Mines avoiding pumping cementitious grouts are sometimes using pre-tensioned resin encapsulated solid cable bolts of over 90 tonne capacity. Results from various industry and University research has led to manufacturer's fine tuning the construction of their cable bolts. A review of this research explains how smooth wire construction is now dominant. Aggressive shear has also led to some mines using 8 tonnes pre-tension instead of the previous common 20 tonnes pre-tension. Lower pre-tension acceptance is now leading to a greater use of threaded cable bolt end fittings, these are tensioned to 8 tonne using the drill motor torque. A recent development is the TEX cable bolt, a slim line threaded end fitting that fits with the drill hole like a standard rock bolt. This cable is being installed at the coal face as primary support off bolter-miners. The laboratory and in-situ testing of the TEX cable is presented. In a bid to improve gateroad development rates and ground support in the last several years, a 100 tonne tensile capacity Goliath cable system was developed. The latest development in resin anchored solid cables is a 110 tonne capacity cable bolt, with laboratory and in-situ testing results presented.

Jun 25, 2024

By E. Fidler

A recent headline in the Wall Street Journal declared, "trendy management schemes very often fail." Many of the management techniques addressed in the accompanying article are associated with quality management including reengineering, benchmarking, total quality management, and employee empowerment. The article made the point that executives, employees, and customers who are involved in such programs rate the effectiveness of these programs very low, and the programs often fail. Yet, we all know of companies that have made significant advances in their operations using these same quality management practices. Why do a few succeed while many fail? History has shown that the companies that successfully carry out quality management programs have two things in common: 1) Strong leadership committed to the success of the program. 2) A comprehensive plan for carrying out and maintaining the program. Stated another way -the reason many companies fail is the lack of committed leaders and inadequate planning. It is ironic that the title of the Wall Street Journal article is "The Best Laid Plans."

Jan 1, 1994

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976