Search Documents

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Cheng, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates have wide application in global smelting operations, comprising primarily of chalcopyrite (CuFeS2) as the principal mineral, accompanied by chalcocite (Cu2S) and bornite (Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates frequently harbor detrimental impurities, notably fluorine ions, which can cause various complications during the smelting process. Moreover, an elevated fluorine content in copper concentrates may entail financial penalties and sales constraints. This review conducts a comprehensive analysis of existing methods for the removal of fluorine, presenting a nuanced assessment of their merits and demerits. It also provides valuable insights into the current landscape of fluorine elimination from copper concentrates and pinpoints pivotal areas warranting future investigation. This review endeavors to serve as a pragmatic resource for researchers and industry professionals operating within this domain.

Jan 1, 2024

By Frederick C. Moore

This paper describes the original planning which actually resulted in the opening of a new aggregate plant located in central New York State. This plant, which is now named the Skaneateles Plant of The General Crushed Stone Company is unique in that the plant itself is a departure not only in design but in concept of operation from the normal aggregate plant the company has operated in the past. Whether or not the concepts which resulted in the Skaneateles Plant are economically feasible remain to be proven by the next few years of operation. By way of background data about our company which will help set the stage for this presentation, we currently operate seventeen stone quarries in the states of New York, Pennsylvania and Virginia. These quarries range in size from 200,000 tons per year to 1,500,000 tons per year with a total annual stone production of approximately 7,500,000 tons. We also produce about 1,250,000 tons of sand and gravel at six sand and gravel plants, 300,000 cubic yards of ready mix concrete, 1,500,000 tons of bituminous concrete, aglime and other minor construction materials. In many cases we are our own best customer consuming a large percentage of the total production of our own aggregates in our various ready mix and blacktop plants. Up to the concept of the Skaneateles Plant our operating facilities have been of the permanent type as opposed to the moveable or portable type plant. The steps involved in the case history of Skaneateles will begin with the basic economic requirements, market research, geologic surveys, land acquisition, zoning and financing and carry through to the final design and construction. We will attempt to show what some of the problems were, how we interpretted them and how we proceeded to solve them. The current results are apparent and can be analysed. The success of the total concepts of the Skaneateles Plant remains for future analysis.

Jan 1, 1968

By B. Akwasi Osei

The lack of metrics to assess clamshell formation dredgeability limits the ability of engineers to predict the dredgeability of compact material and increases the risks associated with clamshell selection. Research is needed to develop metrics for predicting clamshell dredgeability. The objective of this paper is to evaluate possible metrics to predict the dredgeability of compact aggregates by hydraulically actuated clamshell dredges. Data on cylinder pressures and displacements, motor current, bucket tilt and cycle time (CT) were collected from a dredge. Work done and motor energy, potential metrics, were computed and their suitability in predicting dredgeability evaluated. Data analysis shows that; there is no correlation between tilt angle and work done or motor energy; a low correlation between CT and work done, and a strong correlation between CT and motor energy. Work done is a better measure of formation dredgeability, than motor energy, as it shows lower variability. However, in difficult digging conditions, work done alone does not accurately predict dredgeability. This work shows that, it is feasible to use cylinder pressures and motor signals data to predict dredgeability.

Jan 1, 2010

The authors provide a discussion of the paper, ?Coal workers? pneumoconiosis prevalence disparity between australia and the united States,? a peer-reviewed paper that appeared in the technical papers section of the July 2012 issue of Mining Engineering magazine. The original authors, G.J. Joy (gjoy@cdc.gov), J.F. Colinet (jcolinet@cdc.gov) and D.D. Landen (dlanden@cdc.gov), respond.

Jan 1, 2013

By Angelina Anani, Nilufer K. B. Akbulut, Sefiu O. Adewuyi

Crucial information about safety, design, and operation can be utilized in underground mines from ground movement data. Communicating the information and exploring new findings can be a challenge in a decade where there is an ever-increasing volume and velocity of data due to advancements in mining technologies. This challenge escalates for geotechnical data as it is multidimensional, depending on the space and the rate it takes place. To tackle this challenge, geotechnical engineers should focus on utilizing simple yet compelling visualization of rock mass data in 3D. Competent visualizations of ground conditions as a Trigger Action and Response Plan (TARP) could ease the communication of safety concerns and the exploration of rock mass displacement and strain surrounding an opening at an underground mine. Therefore, this study focuses on using scientific visualization methods by rendering geotechnical data over the surface of a 3D mesh model to display TARP levels. The study is conducted at the San Xavier (SX) Underground Mine Laboratory’s East decline. The project aims to produce visualizations that optimize the use of geotechnical data in near-real-time.

Feb 1, 2025

By Spencer R. Titley

Porphyry copper deposits in the southwestern Pacific area represent relative newcomers to the growing number of occurrences of this mineral deposit type. In addition to firmly establishing the importance of this region and its potential influence within the framework of world copper resources, the deposits of this region are significant from a scientific point of view because of their close relationship to the phenomena of Island Arc evolution. Since the discovery of Panguna on Bougainville in 1964, the list of prospects, proven and unproven, and developments, has grown to more than twenty and the number continues to increase. At the time of this writing, the number of prospects is imperfectly known but the following localities and numbers are fair minimum approximations: Manus (Admiralty Islands) (3); New Britain (5); New Ireland (1); Guadalcanal (2); New Guinea Highlands (6); Misima (1); and Fiji (2); Proven prospects are present in the new Guinea Highlands (2); one deposit is being developed in Test Irian, and one orebody, on Bougainville, is in production. This summary paper concerns a discussion of some of the geological characteristics of producers, developments, and prospects on the Islands of Nets Guinea, New Britain, Bougainville, Guadalcanal, and Manus. I am not aware of publishable data for Misima or Fiji. As so many variables ultimately determine whether or not a porphyry copper occurrence becomes an orebody, not the least of which is geography, this summary treats the characteristics of these occurrences which alloy; their assignment to the porphyry copper category. For purposes of this discussion, I have considered those copper occurrences which are apparently genetically related to talc-alkaline intrusions and in which the content of copper has been upgraded 50 to 100 times the Clarke for that particular host rock. Some of these occurrences are shown on Figure 1.

Jan 1, 1973

By D. L. Moellenberg

Under various state laws enacted mostly within the last 20 years, reclamation requirements and standards for hard-rock mining operations have been established virtually everywhere in the western United States. Unlike the uniform and detailed coal mine reclamation requirements under the federal Surface Mining Control and Reclamation Act ( "SMCRA" ) and state programs mode led after SMCRA, the various state law hard-rock mine reclamation requirements are based upon a variety of objectives, and therefore are subject to varying standards from state to state. While the diversity of reclamation requirements complicates the determination of what reclamation measures will be required at any particular mine, there are valid reasons for this diversity. There are dozens of different commodities mined in the United States, and mining methods are different for each commodity. Local natural conditions such as climate, precipitation, geology, hydrology, and biology vary widely across the county. Site-specific conditions also affect mining and reclamation methods. Also, factors such as economics, land use, and environmental protection issues receive different priorities in different states and communities within those states. State reclamation requirements in general provide the flexibility to consider site-specific circumstances, allowing operators to design and engineer the best reclamation measures for each mining site. To the mine developer or manager, reclamation requirements must be translated into design, operational, and closure measures for mine planning. Each of these measures must then be assigned additional costs to be factored into the economic decisions for a particular mining operation. On a broader level, reclamation costs must be factored into decisions such as where to invest in exploration and mine development. The purpose of this paper is to provide a summary of the state non-coal mine reclamation requirements in twelve western states. This summary comparison may be useful as a starting point in considering how local reclamation requirements will impact potential mining costs.

Jan 1, 1994

By Doug Harding

The Metropolitan St. Louis Water District’s Project Clear is a 28-year program targeting wastewater capacity throughout St. Louis, MO. The extensive program includes the Jefferson Barracks Tunnel, running parallel to the Mississippi River at 2 m ID and 5,400 m long. A rebuilt Robbins Main Beam TBM began boring but hit challenging conditions about 2,400 m in, including water inflows. A larger 4.1 m Robbins Main Beam machine will complete the remaining 3,050 m in limestone, dolomite, and shale. The TBM will utilize a high-powered, high breakout torque cutterhead along with enhanced 360-degree probing & grouting capabilities to detect any karst formations.

Dec 1, 2022

By Michael Wortley

Metso?s Process Technology and Innovation group is a world leader in mineral processing consulting. A significant amount of this consulting work involves process integration and optimization (PIO) studies, which include investigating the effects of drill-and-blast design and implementation on downstream processing. Critical to these studies is the ability to track specific ore into, and through, the plant. To increase the accuracy of this ore tracking, Metso Process Technology and Innovation (PTI) developed a system to track ore using a radio frequency identification (RFID) transponders technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and, finally, into the concentrator. The system is called SmartTag. Since its commercialization in 2007, SmartTag has been used in the majority of PTI?s consulting projects, and several permanent systems have been installed worldwide.

Jan 1, 2012

By J. H. Wilhelm

Continuous thickeners can be sized either from previous experience, continuous pilot-scale test results, or from batch settling tests. Although it is a relatively simple process to size full-scale thickeners when previous experience or pilot-scale operating data are available, batch testing is often the only realistic method for sizing thickeners due to time restrictions, budget limitations and availability of sample material. Many authors have, therefore, suggested means of running batch tests and analyzing the resulting data. Fundamental thickening theory had its beginning with the work o£ Coe and Clevenger(1). In order to determine the size of the thickener settling area, they proposed that a series of batch settling tests be run at various initial concentrations. The solids handling capacity at each concentration can then be determined and the lowest capacity (maximum area requirements) used to size the thickener. Kynch(2) developed a mathematical analysis in which the relationship between solids concentration and settling rate can be obtained from a single batch settling curve. Talmage and Fitch(3), Yoshioka(4)(5) and Dick(6), have enlarged upon these works to give a basis for methods of sizing thickeners.

Jan 1, 1979

By M. L. Brashears

Pine Point Mines is located in the Northwest Territories of Canada, about 500 miles north of Edmonton, Alberta (figure 1). Lead-zinc ore is found in numerous localized deposits along a generally east-west trending reef of Devonian dolomite, about 5 miles south of Great Slave Lake. A pumping-test program was carried out in 1968 to guide the design of dewatering systems for several open pits that are partially or wholly below the natural ground-water levels. The hydrogeologic conditions, methods employed and results obtained are discussed.

Jan 1, 1971

By B. Ladanyi

An adequate knowledge of the overall behavior of a rock mass at a given site is fundamental to the satisfactory design of a rock slope. The be- havior is controlled by a variety of factors, in- cluding rock type, geological structure, stress and ground water conditions. There are essentially three lines of approach that may be used to obtain information on the in-situ rock mass behavior for the purpose of the design of a rock slope: (1) Direct measurements of rock mass properties by means ol laboratory and field tests. (2) Evaluation of rock mass properties from a study of slope failure case histories and sta- tistical information on stable and unstable natural rock slopes. (3) Evaluation of in-situ behavior of rock mass by using a physical or mathematical model technique.

Jan 1, 1980

By P. -J. Kleiterp

Highwall mining is a mining method to extract coal from a final boundary in open cut mining, trench mining or contour mining. This boundary may have been reached because of economic constraints (economic strip limit) or geographic constraints (spoil heaps, rivers etc.). Coal is mined from visible, horizontal, or near horizontal coal seams by making rectangular, parallel, unsupported drives with an unmanned cutterhead and coal transport system. This is controlled from a mining unit, or launch frame, positioned outside the drive, in front of the highwall. Removal of overburden is not required or is limited to small quantities only. Highwall Mining originated in the 1940 in the Appalachian Coal Field. This paper describes the history of the various machines that have been designed for highwall mining. During the 1990 and later, there has been more emphasis on the safety in highwall mining. Many pillar strength formulae have been derived to determine the required width of pillars in highwall mining and, with that, the economic feasibility of highwall mining. The various pillar strength criteria will be discussed in this paper showing the countries where they are applied. In order to make highwall mining equipment safer and more productive, there have been quite some technological improvements applied to the machines. These technologies make highwall mining ready for the future as a serious mining method, also outside its traditional Appalachian mining area.

Jan 1, 2010

By Sadegh Elyasi

TBMand roadheader are two dominating excavation machines in underground tunnelling projects. The performance of these two tunnelling machines has been reviewed and analysed individually by many researchers from multiple points of view. However, there are almost no studies that have made an extensive comparison between these two machines, mostly from financial points of view. The current study is intended to characterize both financial and technical status of these two mechanical tunnelling machines in one of the biggest coal mines in Iran. The main objective of this study is to define the best method and equipment that meets a predefined economic goal, which is mainly to maximize the net present value. To this end, a technical and financial model based on the geomechanical and financial parameters involved in the project has been prepared and the financial part of the project has been carried out by applying COMFAR III financial analysis software. Subsequently, a sensitivity analysis of the model was conducted in order to evaluate the effect of involved parameters on the project. According to the results, a roadheader has better economic justification than a TBM, while the TBM has a better advance rate than the roadheader.

Feb 12, 2021

By Derek Brennan, Donald Brennan

"The existing Rondout West Branch Tunnel (RWBT) is part of the Delaware Aqueduct which has been in service since 1944 and accounts for more than 50 percent of New York City’s water supply. In early 2015, the New York City Department of Environmental Protection contracted Kiewit-Shea Constructors, AJV (KSC) to construct the Rondout West Branch Bypass Tunnel project (Rondout) in order to mitigate the leakage of 132 million L/ day (35 million gpd) of water from two areas of the existing tunnel; the Roseton and Wawarsing areas.The scope of the Bypass Tunnel 2 project is separated into two distinct phases. Phase 1 consists of completing the shaft sinking to a depth of approximately 274 m (900 ft) at shaft 5B, 213 m (700 ft) at shaft 6B and the excavation of approximately 3,850 m (12,500 linear ft) of tunnel at a diameter of 6.6 m (21 ft 7 in). This phase also includes the installation of 2,804 m (9,200 linear ft) of 4.8 m (16 ft) diameter steel interliner pipe through the new bypass tunnel with cast-in–place concrete liner for a finished diameter of 4.2 m (14 ft). Access chambers at the top of shafts 5B and 6B will be constructed for access and housing of the mechanical and electrical equipment for supporting pumps and valves.Included in phase 2 is the additional excavation from shafts 5B and 6B to the RWBT, and the drainage tunnel to remove ground water infiltration from RWBT. This work will be completed during a scheduled shutdown of the RWBT and will include approximately 31 m (100 ft) of excavation of the two connection tunnels. Additionally, construction of the permanent plugs within the RWBT will be undertaken. Figure 2 shows the layout of the work.Access to the work through the deep shaft at site 5B was critical to the success of the project. The hoisting system needed to be multi-functional to handle the different types of construction from drill and shoot of the shaft, starter and tail tunnel, the assembly of the tunnel boring machine (TBM), the excavation of the TBM tunnel including the supply of the precast segmental liner, the grouting operations, the installation of the steel interliner pipe and the cast-in-place concrete as well as ingress and egress of personnel. The production of the TBM operations was critical to the schedule of the project. This required a quick cycle for muck haulage and supply of the precast segmental liner in order to keep pace with the excavation time of the TBM. For TBM assembly, components were limited to a maximum weight of 104 t (115 st) for a single lift. Various cranes were analyzed for hoisting, however, none would meet all of the citeria. Therefore, the project team selected a specialized hoisting system designed in house in conjunction with Timberland Equipment Ltd. that consisted of a total of 14 separate hoists and winches with a total of more than 2,833 kW (3,800 hp)."

Mar 1, 2019

By K. Häge

"Die Nachhaltigkeit der Braunkohlengewinnung in der öffentlichen Wahrnehmung wird nur weiter erfolgreich kommuniziert werden können, wenn durch konkretes Handeln glaubhaft gezeigt wird, dass die offenen Fragen fair und solide beantwortet werden. Dazu gehören insbesondere die neue innovative technische Lösung sowie das sensible Interessenmanagement. Die Braunkohlenindustrie hat gelernt, dass Offenheit und nicht zuletzt das beständige Bemühen um den Meinungsaustausch mit ihrem Umfeld wichtige Elemente sind. Der in Jahrzehnten erworbene Schatz an Glaubwürdig-keit ist eine Basis, auf der die Braunkohlenindustrie ihre Zukunft gestalten kann. Darüber hinaus sind politische Rahmenvorgaben erforderlich. Das öffentliche Interesse an einer sicheren und preiswerten Energieversorgung unter Einschluss der Braunkohle ist unverzichtbar. In diesem Kon-text kann dann die Braunkohle die an sie gerichteten Fragen der Ökonomie, der Ökologie und der Sozialverträglichkeit auch mit Hilfe von Indikatoren beantworten.ABSTRACTThe discussion of the sustainability of lignite mining can only be continued successfully if the indus-try acts in a practical manner and demonstrates trustworthiness by responding fairly and reliably to open questions. This includes new and innovative technical solutions as well as the sensitive management of interests. The lignite industry has learned that openness and the constant effort to exchange viewpoints within their environment are all essential elements. The credibility that has been gained over the decades is the foundation on which the lignite industry can build its future. Beyond that a framework of political guidelines is necessary. Public interest in a secure and inex-pensive energy supply that also includes lignite is indispensable. In this context, the lignite industry will then be able to answer the questions which are directed at them and concern the economy, ecology, and social tolerability also by indicators."

Jan 1, 2005

By C. E. Jordan

The Tuscaloosa Metallurgy Research Center of the Bureau of Mines, U.S. Department of the Interior, is investigating the recovery of phosphate from beneficiation slime, as part of the Bureau's efforts to conserve mineral resources through increased use of wastes. Phosphate equivalent to about two-fifths of U.S. production is discarded annually in the wastes. Exploratory flotation tests on the plus 5-um fraction of a slime sample showed promise for a classification-flotation technique. Onsite classification tests at six phosphate washing plants were conducted with a two-stage hydro cyclone system designed to recover the plus 5-um material. The cyclone underflows contained 8.3 to 19.1 percent P2O5, and the recovery of the plus 5-um PZOS values ranged from 81 to 95 percent. The percent P2O5 recovery from the total slimes ranged from 38 to 47 percent. Batch-flotation studies are currently being conducted.

Jan 1, 1978

By S. Angioletti

This paper addresses strategic investment decisions when they are nested in a project development format where each project is implemented in phases and each phase is approved to move on to the next phase only if certain technical and economic requirements are met. This configuration is sometimes referred to as a ?Project Portfolio?. Mining companies maintain project portfolios in their exploration investment plan. This study proposes a procedure to best manage an exploration project portfolio including technical and economic uncertainties. The procedure may support decision makers in a simple and intuitive way, while maintaining the rigor and precision required by the rather large amount of financial resources typically called for by mining projects. The procedure was tested in a real case study of a gold mining company and its exploration projects portfolio. The procedure uses the following approaches: i) investment valuation methods under technical and market uncertainties based on Option Pricing Model, Real Option Theory and Option Space; ii) portfolio management and Stage Gate®1 method; iii) Monte Carlo simulation.

Jan 1, 2010

By M. M. Veras, C. H. Sampaio, A. S. Young, D. Neto, C. O. Petter

"Due to new technological developments, automatic sensor based sorting has made progress within industrial minerals, precious metals, diamond, and coal mining in recent years (Lessard et. al. 2016). In order to re-introduce the technology to other mining sectors, this research discusses its application to iron, manganese, and zinc ores through test works performed by the authors. These test works were performed using Dual Energy X-ray Transmission (DE-XRT) sensor technology. In each case, pre-concentrations of the ore were created demonstrating the possibility to reduce waste material, energy costs, and water consumption while improving product quality of the ores. INTRODUCTION Sorting of mining ores is as old as mining itself (Salter, 1991). Sensor based sorting applications in coal mining began as early as the late 19th century (Louis 1928). New sensor technologies were developed and implemented sequentially for uranium, nickel, coal, and gold mining (Refining, 1949, Rose et al, 1950, Bloomfield et al, 1966, Clayton et al, 1987, Robben and Mosser, 2014). While these sensor technologies were developed decades ago, computational capacity to keep pace with the vast amount of information required utilizing the sensor technology did not arrive until recently (Lessard et. al., 2016). The sensor based sorting (SBS) process was effectively described by Salter and Wyatt in Minerals Engineering in 1991, and Wotruba and Harbeck in 2010 in the Ullmann’s Encyclopedia of Industrial Chemistry under Sensor Based Sorting. Both descriptions include the following key steps: 1. Presentation of the material or particles. 2. Examination or detection of the material or particles. 3. Processing or analysis of the data generated. 4. Physical separation of the material or particles by external means. Effective presentation of the material or particles is achieved when the sensor is capable of identifying each particle individually. This step requires that each fragment of the material be isolated, and it often involves acceleration of the material fragments by chute or mechanical means, as well as the spreading of particles by vibratory feeders (Salter and Wyatt, 1991, and Wotruba and Harbeck, 2010). The isolated particles typically are conveyed into an area wherein they are subjected to electromagnetic irradiation (except in cases of some radioactive ores), either in the form of x-ray, visible light, infrared, or other energies. A wide range of applications for sensor based sorting exists in the literature. The majority of applications fall into one of two camps, (1) pre-concentration of mineral ores, or (2) characterization of the material during processing (Buxton and Benndorf 2013). While there is much to be gained from in-line material characterization and the resulting control both of quality and processing, this article focuses primarily on the camp of pre-concentration of mineral ores."

Jan 1, 2017