Search Documents

By Philip R. Whitney

Precipitation of hydrous manganese/iron oxides in streams can be readily observed in much of the northeastern United States, and is apparently a common phenomenon in other glaciated areas (1,2,3,4). Deposition occurs when Mn-enriched ground or surface water enters the stream environment and encounters conditions of higher Eh and pH. The preferred location for deposition is in shallow, fast-flowing segments of stream; the oxides usually form as coatings on detrital material. The experimental studies of Hem(5) and a considerable amount of work on marine and lacustrine manganese nodules(6,7,8) suggest that given an appropriate substrate, deposition of manganese oxides may occur even when the water is undersaturated in Mn with respect to the oxides, due to catalysis by organisms or by silicate, carbonate, or ferric hydroxide surfaces. Once begun, manganese oxide deposition is autocatalytic (9). Studies of the distribution of oxides in various size fractions of stream sediments indicate that the thickness and prevalence of the coatings commonly increases with increasing particle size in the coarse sand and gravel size ranges. Figures 1 and 2 show a fairly typical distribution of leachable metals over nine size fractions from 62 microns up to 8-16 mm. The leaching solution used was neutral ammonium citrate with hydroxylamine hydrochloride, which effectively removes the oxide coatings without significantly attacking most silicates, carbonates or sulfides. Figure 1 shows metal content as ppm of the total sample; figure 2 shows' the same data as micrograms of metal per square millimeter of surface area.

Jan 1, 1975

By J. J. Moore

Combustion synthesis or self propagating high temperature synthesis (SHS) reaction systems are discussed with respect to thermodynamics and kinetics. In particular, tile effect of the process parameters, ego particle size, AHf, ignition and combustion temperatures on these self sustaining reactions is discussed. Combustion theory is used to investigate the effect of the overall activation energy of the SHS reaction on the combustion front propagation rate and in obtaining a clearer understanding of the transition from stable to unstable propagation. Finally, examples of the application of combustion synthesis to advanced materials processes are made, in particular the synthesis of Ni-Ti -X intermetallic shape memory alloys, TiC-Al2O3 and ZrB2 ?Al2O3 ceramic composite materials.

Jan 1, 1991

By J. H. Field

The sulfur dioxide emitted in low concentrations in flue gases from the combustion of sulfur-containing coals and fuel oils is a significant factor in contamination of the atmosphere with sulfur dioxide. A review of methods for treating gases containing high concentrations of sulfur dioxide shows that they are seldom satisfactory for purifying flue gases. Processes developed specifically for treating flue gases using liquid absorbents are costly and may cause localized pollution, because the cooled flue gases can settle in the vicinity of the stack. Bench-scale research is being conducted to investigate the use of dry absorbents for sulfur dioxide removal at temperature levels of about 250°- 300° F. and 600°-650° F. Alkalized alumina has been found effective for treating simulated flue gas and Is regenerable by hydrogen, carbon monoxide, or producer gas. Other metallic oxides have been tested as absorbents also. Chemically impregnated activated carbons removed sulfur dioxide from the gas at 265° F. Vanadium pentoxide is effective as a catalyst for oxidizing of sulfur dioxide in the simulated flue gas at temperatures lower than have been used commercially for gases with higher concentrations of sulfur dioxide. Conversions of sulfur dioxide to trioxide wore studied as a function of temp- erature over a range of about 570° to 750° F.

Jan 1, 1959

By M. E. Buzon, M. E. Gunter

Talc has been the focus of recent civil litigation based on claims that asbestos minerals exist in talc deposits and therefore have caused asbestos-related diseases in those who have regularly used talc products. Such litigation, and ensuing confusion over the petrology and asbestos content of these deposits, challenges the talc mining industry in Montana and elsewhere in the world. The talc deposits in southwest Montana were formed by hydrothermal alteration of dolomitic marbles and are still actively mined. In general, talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic and lacking in amphiboles. This paper includes data from analyses of representative ore samples from this mining region in southwest Montana. The results conclude that the presence of asbestos minerals — both amphiboles and chrysotile — is unlikely and that the ores are nearly monomineralic, as expected. Samples were characterized using a suite of analytical methods, namely, powder X-ray diffraction, X-ray fluorescence spectroscopy and electron microprobe analyses, which allowed us to determine the minerals present and the formation process. Our data and interpretations suggest that previous identification of asbestos minerals in these deposits is not accurate.

Jan 1, 2018

By M. E. Buzon, M. E. Gunter

Talc has been the focus of recent civil litigation based on claims that asbestos minerals exist in talc deposits and therefore have caused asbestos-related diseases in those who have regularly used talc products. Such litigation, and ensuing confusion over the petrology and asbestos content of these deposits, challenges the talc mining industry in Montana and elsewhere in the world. The talc deposits in southwest Montana were formed by hydrothermal alteration of dolomitic marbles and are still actively mined. In general, talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic and lacking in amphiboles. This paper includes data from analyses of representative ore samples from this mining region in southwest Montana. The results conclude that the presence of asbestos minerals — both amphiboles and chrysotile — is unlikely and that the ores are nearly monomineralic, as expected. Samples were characterized using a suite of analytical methods, namely, powder X-ray diffraction, X-ray fluorescence spectroscopy and electron microprobe analyses, which allowed us to determine the minerals present and the formation process. Our data and interpretations suggest that previous identification of asbestos minerals in these deposits is not accurate.

Jan 1, 2017

By Willard A. Murray

Investigations of underground coal gasification (UCG) have been actively pursued by the U.S. Department of Energy since the early 1970s; the Lawrence Livermore National Laboratory (LLNL) conducted its first field experiment in 1976. In conjunction with field and laboratory studies of the process of recovering energy in the form of combustible gases from the burning of coal deposits in situ, an extensive environmental program has been conducted at LLNL under the auspices of both the U.S Department of Energy and the U.S. Environmental Protection Agency. This program has focused on groundwater contamination and ground surface subsidence caused by UCG. The material presented in this paper is a summary of results from the environmental studies of UCG activities conducted by LLNL as described by Mead, et al. (1981) and supplemented by the author's experience with this program in 1980 and 1981. The following sections describe specific groundwater contamination and surf ace subsidence problems encountered during field experiments in northeastern Wyoming, and will discuss implications of preliminary findings from geohydrological investigations of a site in southwestern Washington. Finally, possible environmental control technologies that are most likely to be effective in mitigating environmental impacts are discussed.

Jan 1, 1982

By Jurgen H. Kleinau

This paper details Keeler/ Dorr-Oliver's experience with the application of fluid bed combustion technology to the burning of coal-mining waste. The designs of two stage fluid bed combustors/dryers are demonstrated as useful in the drying of coal, slag and coke, using coal and coal refuse (gob) as fuel. Anthracite mining refuse (culm) is more than abundant in Northeastern Pennsylvania. After demonstration at Shamokin, Pennsylvania, a full commercial-sized fluid bed boiler using culm is used for district heating in Wilkes-Barre, Pennsylvania. Limited research work has shown the utility of using fine coal as filter aid in sludge in¬cineration. With the rising avenues of the suitability of coal as auxiliary fuel in fluid bed sludge incineration, an expansion of these concepts combines the use of coal or coal refuse as filter aid and auxiliary fuel. Lime¬stone addition controls SO2 emission.

Jan 1, 1985

By John B. Gustavson

The mineral deposits found in carbonate facies rocks of sedimentary basins include deposits comprised of the country rock itself such as limestone for chemical uses, dolomite for road aggregate, and a variety of other industrial uses of the sedimentary rock. Exploration for new reserves is generally conducted on basis of outcrop investigation, subsurface drilling, and facies change studies while geophysics and geochemistry are not applied. In contrast, rapid development has taken place in the application of both geophysical and geochemical techniques in exploration for stratiform deposits of zinc, lead, barite, and fluorite deposits. This paper will present case histories and show illustrations from such work in the Mid-Continent region. The Metals Division of International Oil & Gas, Inc. has gathered this experience through work over the last three years along the southern margin of the Eastern Interior platform focusing on the states of Arkansas and Tennessee. The exploration work was conducted partially for the Company's own account, partially in joint exploration ventures with mining companies including International Mogul Mines, Ltd., a Canadian company; Bear Creek Mining Company, a subsidiary of Kennecott Copper Corporation; the Mining Division of W. R. Grace and Company, and Boliden-Preussag Exploration, a Swedish-German partnership. We wish to take this opportunity to thank our venture partners for allowing presentation of the various sections of this paper.

Jan 1, 1976

By Milos Krofta, Donald B. Aulenbach, James P. Van Dyke

INTRODUCTION An innovative Ø.1-MGD (378.5-m3/day) biological and phyicochemical wastewater treatment system at Hancock, Massachusetts, USA, has been treating the domestic sewage generated from the four-season Jiminy Peak timeshare resort since 1985. The influent raw sewage is collected and equalized in an equalization tank, then biologically treated by two rotating biological contactors (RBC). A portion of the RBC effluent is discharged to a secondary sedimentation tank to simulate conventional waste treatment by a conventional RBC system. For parallel treatment the remaining portion of the RBC effluent is discharged to an innovative Sandfloat (SASF-8) clarifier to simulate a two-stage biological and physicochemical treatment by RBC-Sandfloat. Both secondary sedimentation effluent and Saandfloat effluent are later combined together and discharged to a tertiary sand filter and two UV disinfection'units for final polishing. The operation and performance data of Jiminy Peak plant in the period of May 1985 to March 1988 was fully documented in the Lenox Institute technical report No. LIR/Ø3-88/292 (391 pages, March 1988). This report presents only background information and complete plant data in the period of April 1988 to January 1989. Dr. Lawrence K. Wang and Mr. James P. Van Dyke have been the Consulting Engineer and Director of Special Projects, respectively, for the Jiminy Peak Project since 1985. (Key Words) Innovative and Alternative Technology, Rotating Biological Contactor, Sandfloat, Dissolved Air Flotation, Sedimentation, Tertiary Filtration, Ultraviolet, Disinfection. BACKGROUND INFORMATION Jimmy Peak, Inc., Hancock, Massachusetts, has designed and constructed a secondary wastewater treatment system consisting of preliminary/primary treatment facilities, two rotating biological contactors, a dissolved air flotation clarifier, a secondary sedimentation clarifier, a sand filter and two ultraviolet (UV) disinfection units. Total average wastewater flow is approximately Ø.1 ) (378.5 cubic meters per day). In accordance with the Consulting Engineer's preliminary design, the total wastewater stream is initially collected and equalized by an equalization tank, and then biologically treated by rotating biological contactors (RBC). Part of the RBC effluent is diverted to a Krofta Sandfloat (SASF-8) for physicochemical clarification in order to simulate an innovative RBC-Sandfloat two-stage waste treatment system. The remaining part of the RBC effluent is diverted to a sedimentation tank for secondary clarification in order to siumulate a conventional secondary RBC-sedimentation waste treatment system for the purpose of parallel comparison. Both Sandfloat effluent and sedimentation effluent are later combined together and discharged to the subsequent sand filter and UV disinfection unit for final polishing. Figure 1 shows the flow diagram of Jiminy Peak Plant. The Massachusetts Clean Waters Act (M.G.L.c.2l,s.26-53) was amended by Chapter 246 of the Acts of 1973 to authorize the Massachusetts Department of Environmental Quality Engineering (DEQE), Division of water Pollution Control, Boston, Massachusetts, to regulate discharges into all waters of the Commonwealth of Massachusetts, including groundwaters. The DEQE regulates discharges through the issuance of discharge permits which impose limitations on the amount of pollutants which may be discharged in the effluent, together with monitoring and reporting requirements and other conditions to insure adequate treatment of all liquid wastes prior to discharge. The DEQE reviewed the application submitted on behalf of Jiminy Peak, Inc. for a permit to discharge sanitary wastes from the Jiminy Peak secondary wastewater treatment system located off Brodie Mountain Road, Hancock, Massachusetts, and subsequently developed the conditions contained in the Groundwater Discharge Permit No. Ø-188. More specifically, Jiminy Peak, Inc. (i.e. the permittee) has been authorized to discharge into the ground from the Jimmy Peak secondary wastewater treatment facilities for which the Permit No. Ø-188 was issued, a treated effluent

Jan 1, 1989

By B. E. MacNab

During the past several years, Raymond Kaiser Engineers has prepared numerous studies concerning the technical and economic feasibility of coal exporting facilities in the western United States. Perhaps the most striking conclusion to be drawn from these efforts is that many people underestimate the complexity of the highly competitive, dynamic coal marketing system which includes coal loading terminals as an essential but relatively low-cost link in the energy production and delivery chain. The title of this paper, "The Status of Western United States Coal Ports - An Economic Assessment," should not delude anyone into thinking that the future of western U.S. coal- exporting ports has now congealed into a well- defined economic plan. As this paper will demonstrate, the situation is complex and more dynamic than ever and promises to remain so into the late 1980's.

Jan 1, 1982

By J. Potter, A. Anani, C. Antonio

This research aims to test the hypothesis that the low retention rate of women in the mining industry is caused by workplace culture and policies established due to gender segregation. A quasi-experiment is developed to determine the cause-and-effect relationship between gender segregation-inspired culture and the retention of women. The experiment considers the impact of the job type and the operational environment. The analysis provides information on factors that cause low retention of women in the industry, the extent to which gender segregation plays a role, and insights that allow actionable and measurable changes in the industry.

Feb 1, 2023

By D. J. Englund, R. A. Davis

"A three-dimensional CFD model of a straight grate furnace for indurating iron-oxide pellets was developed for exploring conditions of furnace operation for fluid flow, heat transfer and reactions. The model includes reactions for natural gas combustion in the gas phase and calcination and magnetite oxidation as well as drying in the pellet bed. The performance of the model was investigated with a series of pellet production rates that included adjustments to the fuel rates to achieve proper induration temperatures in the pellet bed. The model may be used to discover opportunities for process improvement.IntroductionIron oxide pellets are a feedstock to blast furnaces for iron making. Pellets require physical strength characteristics needed to maintain their integrity during storage, handling, transportation and smelting. Pellets are produced from iron ore in a series of mineral processing operations that form wet green balls from slurries of iron-ore concentrate with binders, such as bentonite, and possibly fluxing-agents such as limestone and dolomite. The green balls are dried, fired at high temperature, and then cooled in an induration furnace to achieve the strength and chemical composition required for efficient reduction and slag separation in blast furnaces. Induration furnaces are generally straight grates or grate-kilncooler configurations. These furnaces operate with pellet beds passing through a series of temperature zones to control drying and chemical reactions in the bed.Process air passes through the zones in an overall counter flow direction to the pellets for efficient heat transfer and energy recovery from the cooling stage. Consequently, the zone conditions and the overall furnace performance are highly coupled. Thus, it becomes challenging to predict how changes to any single zone may affect the rest of the furnace. To gain a better understanding of machine performance and coupling, a three-dimensional, steady-state model of a complete straight grate induration furnace was created using computational fluid dynamics (CFD)."

Jan 1, 2015

By A. Podlesny, E. N. Rubinstein, J. J. Sammarco, B. Demich

Roof bolting typically follows the extraction of a commodity to help keep the roof from collapsing. During 2004 to 2013, roof bolter operators had the highest number of machinery-related injuries, accounting for 64.7 percent, at underground coal mines. This paper analyzes U.S. roof bolter fatal and nonfatal lost-time injury data at underground work locations for all commodities from 2004 through 2013 and determines risk indices for six roof bolting tasks. For fatal and nonfatal incidences combined, the roof bolting tasks in order of the highest to lowest risk index were bolting, handling of materials, setting the temporary roof support (TRS), drilling, tramming, and traversing. For fatalities, the roof bolting tasks in order of the highest to lowest risk index were handling of materials, setting the TRS, bolting, drilling, traversing, and tramming. Age was found to be a significant factor. Severity of injury, indicated by days lost, was found to increase with increasing age as well as with increasing experience, largely due to the confounding of age and experience. The operation of the roof bolting machine used in underground mining should be a research priority given the high frequency and severity of incidents. The results also suggest that temporal factors may exist, so additional research is warranted to better understand these factors and potentially develop interventions. This research provides a datadriven foundation from which future research can be conducted for safety interventions to reduce the frequency and severity of incidences involving the roof bolter activities of bolting, handling of materials, and setting the TRS.

Jan 1, 2016

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air pollution control is included. However, there are clear indications that natural gas supply from the contiguous 48 states and continental shelves will not indefinitely keep up with this rapid growth in demand. Projections are presented which define the extent of potential deficiencies from the 1970's to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale - by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current minemouth prices - 60-70 million' tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase is gas demand.

Jan 1, 1969

By G. F. Revey

All underground operations have limiting factors that influence overall profitability. Hoisting, hauling, available headings, labor, milling capacity and other factors limit how much material can be removed from an underground mine. Consequently, when mines use limited labor to handle the additional rock from overbreak and to perform extra ground support tasks, productive activity is replaced by non-productive work. Mining economics are further penalized when overbreak causes dilution of ore grades. This paper reviews organizational systems that mines have used to create environments which foster the creation of successful overbreak control programs. Actual case histories document the various quality improvement techniques, worker incentives, and practical project management systems used by these mines. A brief review of controlled blasting technology sources and overbreak measurement tools is also included.

Jan 1, 1997

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines has developed a PC based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1994

By K. Kim, T. M. Yegulalp

A new explanation of the scale dependency of rock strength is presented based on the theory of extremes. A brief review of past work on specimen size and strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect. It is shown that the weakest link theory is directly related to extremal statistics and that parameters of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1994

By Paul H. Johnson

Resource Engineering and Development, Inc. is designing and building a portable 150 to 225 TPD, flotation-cyanide leach plant with unitized, skid-mounted components. This plant design, with its portability, low capital investment, and high recovery of silver and gold from many partially oxidized ores, is well suited to treat many small, high-grade deposits, old waste dumps, and old mill tailing piles. A description is given of flotation and/or cyanide leach tests run on about 17 partially oxidized, newly mined ores; waste dump materials; placer slimes; and old mill tailings.

Jan 1, 1981

By T. C. Murray

An automatic control system was recently installed to insure the continuity of operation between the ship docking and ore handling facilities and the computerized conveyor-fed sintering plants and blast furnaces. Although the basic concept for material handling has not changed, many innovations including computer control have been implemented.

Jan 1, 1978

By Paul A. Rittenhouse

First of all, I want to thank John Dunlap for asking me to this AIME meeting in Denver. I was first introduced to Denver and The Rocky Mountains more than ten years ago and immediately decided it was one of the most attractive spots in the world. I've come back many times since and still welcome any opportunity to return, even if it means I have to prepare and give a paper on potash. When John Dunlap gave me this assignment, he told me that the program would include papers on the geology of potash, papers on new discovered potash deposits and new mines and asked me to discuss potash from the commercial point of view. He also asked me to include a supply/demand outlook for potash. However, one thing he did not mention was "how far into the future he wanted me to look" and it seems to me the time element is a crucial factor to you who are both geologists and miners as well as to me. In your case, you have to look far enough into the future to give you time to explore, find, evaluate, develop, and bring into production a commercial deposit. My mining associates and friends don't agree on how long that takes but it's probably somewhere in the range of eight to fifteen years. But, they all agree on one thing and that is that the time required is continually getting longer. Now my time problem is just the opposite. It is "relatively" easy, and I stress relatively, to identify and evaluate the importance of the various factors that impact on both the supply of and demand for a commodity such as potash if the time period is today. It gets a little tough if one has to project into tomorrow or next week or next month. And when we start talking in terms of a year, five years or ten or fifteen years, things really get sticky and the old crystal ball becomes mighty cloudy. But we economists and forecasters are not known for our temerity so let me get on with the job at hand and take a look at the world potash supply/demand outlook.

Jan 1, 1978