Search Documents

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By Justin Cardwell, Alyson Cartwright

"Grade estimation is the cornerstone of longrange mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model.Certain deposits, such as the sedimenthosted deposits at Tenke-Fungurume, require an interpolation method that best suits the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the nonstationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface.Geology overview. The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Fig. 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Fig. 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006)."

Jan 1, 2015

By Sabina Brady

Nearly a decade and a half after the US and China established formal diplomatic relations, and two decades after the two countries signed the Shanghai Communique and established commercial ties, the world, and perhaps China itself, has discovered that a wealth of natural mineral and energy resources lie beneath China's soil and directly off its coast. The country's coal reserves and oil and gas potential are well known. Its ferrous and nonferrous metal reserves are respectable and in a number of instances pre-eminent. According to 1981 Minerals Yearbook estimates - more often than not below those now being claimed by China - the country's aluminous metal reserves are about 907 Mt (1 billion st); iron ore reserves are 40 Gt (44 billion st); and copper reserves are about 46 Mt (54.4 million st) of contained metal. In addition, the country has about 10.7 Gt (11.8 billion st) of phosphate reserves, the fourth largest in the world, and 3 Gt (3.3 billion st) of pyrite. China's national Sixth Five Year Plan promulgated in late 1982 ended a stringent three-year retrenchment or readjustment period in which a number of major development projects involving foreign participation initiated in the late 1970s were shelved. The new Five Year Plan is a signal both within and outside of China that things are now moving again, and that major industrial and service sectors are receiving the kind of funding and flexibility they need for expansion, construction and modernization. The new plan's strategy for growth is measured and much less grandiose and frenetic than it was five years ago when China flung open its doors to foreign companies and invited participation in large-scale development projects. Now, the country's reticence to spend foreign exchange to purchase key equipment, technology, and services -a reaction to these projects and the spending they entailed - is clearly on the wane. In China's effort to quadruple its GNP by the year 2000, there is a new willingness to use some of its substantial foreign reserves. In fact, it is projected that 1983 will witness a $1.9 billion deficit, with a $2-3 billion deficit in 1984 and 1985. The following article discusses implications the Sixth Five-Year Plan has for nonferrous metal development in China. It is the first in a series of three articles on Chinese mineral resource development to be published in Mining Engineering over the next few months. The second article will identify specific nonferrous projects underway, while the third in the series will focus on trade and development opportunities for phosphate and potash producers in China. China's Ambitious Plans In the last few months, the exploitation of China's nonferrous resources and development of its industrial processing capabilities have begun to receive increasing attention on both provincial and central levels. Unlike the earlier modernization drive of 1978 when China's ferrous sector - best typified in the Baoshan iron and steel project - got the lion's share of the Ministry of Metallurgical Industry's (MMI) energy and resources, it now appears that in some respects the nonferrous and industrial sectors are finally moving out from beneath the dominating shadow of ferrous and getting their own day in the sun. Separation of Nonferrous from Ferrous One clear demonstration of this is the establishment in April 1983 of the China Nonferrous Metals Industry Corporation (CNFMIC). The corporation is composed of 819 enterprises with over a million workers, and also includes 12 nonferrous metal construction companies, eight design institutes, and three prospecting companies. Of ministerial rank, CNFMIC is responsible for the development of both the country's nonferrous resources and its processing facilities. Although closely tied to the parent ministry from which it sprang (i.e. MMI), CNFMIC, at least theoretically, is separate and independent from it. One strong indication that this independence is, or soon will become a reality, can be seen from the fact that the new corporation is not headed by the former MMI officials, not even those who made up the ministry's now defunct nonferrous bureau. Instead, its president Qiu Chunfu is formerly of the State Economic Commission and the China International Trust and Investment Corp. Its general manager Fei Ziwen, an engineer in his early 50s, is from the Jiangxi Province Copper Corp. The new nonferrous corporation appears to be powerful

Jan 7, 1983

By D. H. Horswill

Red Dog, the world’s largest zinc mine, is located ninety miles north of the Arctic Circle in northwest Alaska on lands owned by the Inupiat Eskimo organization called NANA. NANA received a subsurface title over this resource as part of their settlement lands under the Alaska Native Claims Settlement Act and subsequently entered into a Lease Agreement with Cominco in 1982. Cominco, an international mining company focused on zinc, built and operated the mine. NANA’s principle objective in the development of the mine was to have it contribute to the development of sustainable communities within their traditional region. This meant creating job opportunities in a modern economy while preserving the traditional subsistence lifestyles. Preservation of their culture, language, and traditions are as important to the NANA people today as they were through ages past. The principles of sustainable development – matching economic, environmental, and social goals through continuous communications and high commitment to efficient and effective operations – have been core values for the Red Dog Mine from the beginning. This paper will describe how a large mining operation in a remote corner of the world has been able to contribute toward sustainable development in that region.

Jan 1, 2000

Invensys’ recently introduced Field Device Manager for Foxboro I/A Series distributed control systems provides the industry’s first solution that takes advantage of both the latest Enhanced Electronic Device Description Language (Enhanced EDDL) and FDT technologies. This combination provides comprehensive lifecycle support to configure, calibrate, commission, diagnose and optimize the performance of any vendors’ foundation fieldbus device. The I/A Series Field Device Manager enables users to take advantage of any EDDL, Enhanced EDDL and/or FDT host deliverables supplied by the device vendor.

Jan 1, 2007

By V. T. McLemore

New Mexico Bureau of Geology and Mineral Resources (NMBGMR) has been collecting data on uranium mining districts, mines and mills since it was created in 1927 and has converted years of historical data into a relational database that can be imported in ArcMap. The database includes information on mining districts, mines, mills and geochemistry, as well as photographs and bibliographic resources. The available data includes location, production, reserves, geologic, geochemical, resource potential and other data. The National Uranium Resource Evaluation (NURE) stream-sediment data provides geochemical analyses for >27,000 samples collected in New Mexico during the 1970s. The NURE hydrogeochemical data provides analyses of water samples. ArcMap includes the location of individual ore bodies as polygons and incorporates the mines and NURE data as individual site locations. The purposes of these databases are to provide computerized data that will aid in identifying and evaluating resource potential, resource development and management, production and possible environmental concerns, such as physical hazards (i.e., hazardous mine openings), indoor radon, regional exposure to radiation from the mines, background geochemical data and point sources of possible pollution in areas of known mineral deposits.

Jan 1, 2010

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By R. M. Powers

The Florida Institute of Phosphate Research (FIPR) has funded a four-year research project to develop a computer model 'which will predict the hydrologic impacts of phosphate mining on surface and groundwater systems. The core of the model is an analytical geographic information system (SPANS) which integrates EPA's Hydrology Simulation Program Fortran (HSPF) surface water model with the McDonald-Harbaugh groundwater model (MODFLOW). The hydrologic model conducts both event and continuous annual Simulations driven by variable precipitation and temperature data. The model is currently being calibrated and will be ready for distribution to the user community in mid-1991.

Jan 1, 1990

By Andre Vien, SANDRO DAVID DI, Frank Laroche

In 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution–size distribution relationship. This allows grade and recovery predictions from a varying mine plan through product size distribution predictions. 

By R. Berton, M. Walden, S. Melberg, N. Rocco

Recent tailings dam failures around the globe have influenced many mining industry regulators to reassess their requirements for the numerical modelling of tailings dam failures. This type or forward modelling is associated with overarching uncertainties as the model cannot be calibrated against a physical result. Dam breach analyses that meet the requirements of current industry standards and guidance typically begin with identification of credible failure modes and selection of appropriate topographic data set to represent the study area. The breach parameters and the volume of tailings released are then determined using available methodologies and empirical relationships. Subsequently, when the breach hydrograph is developed and the hydrology of stream networks are complete, the runout simulation is implemented. Due to the uncertainty involved in the process, sensitivity analyses are recommended to quantify variations in model inputs on the inundation extent and the flow characteristics. This paper outlines some common methodologies utilized for development of dam breach models, summarizes associated uncertainties with these methodologies and inputs, and provides guidance on how sensitivity analyses can address a wide array of uncertainties inherent in tailings breach analyses. This paper provides an understanding of how selecting appropriate breach parameters can result in reasonably conservative inundation extents consistent with the identified credible failure modes.

Mar 2, 2022

By Virgil L. Barr

National income originating compared to physical production for an enterprise or an industry reflects its ability to strengthen the national economy. For a single industrial sector or for an industry this comparison can be useful to reflect changes that may occur in this ability to contribute because of changing supply-demand-income-investment equilibria. A favorable relationship can be postulated by specified economic incentive, and the accompanying technologic input required can be shown. The new index proposes the use of the Federal Reserve Board indexes of production divided by the constant dollar income originating in the petroleum industry which reflects increases or decreases in performance. When compared with other mineral industries and with, total industry, an approximation of relative strength is evident. By constructing three different hypothetical conditions for future petroleum imports, assuming a constant excess capacity requirement for domestic production, and providing an estimate for future domestic demand for petroleum, the impact on the performance index can be shown. Thus, a strong position for the petroleum and natural gas industry can be stated. If this is done, it becomes evident that because of restrictions on cost-price relationships, a drilling program that would provide enough domestic oil to meet demand may not be practicable. By difference, the amount of improvement in methods of production and processing through technologic advancements can be stated explicitly.

Jan 1, 1960

By K. J. Shoop

Coal-fired power plants in the U. S. produce approximately 20 million metric tons of Hue-gas desulfurization sludge every year. The sludge mainly consists of calcium sulfite and calcium sulfate. This can be converted to synthetic gypsum, which in principle could be a marketable commodity. However, many Hue-gas scrubbers produce sludges that do not meet the quality requirements of the gypsum industry, and so their sludges must be landfilled as a waste. If a suitable method can be developed for removing certain objectionable impurities from the sludge, it will then be possible to market the material instead of landfilling it. A sludge from a natural-oxidation scrubber was characterized, and the main contaminant was found to be calcium carbonate from unreacted limestone. Based on the particle size and the characteristics of the material, froth flotation was considered as a method for purifying the material. Since no flotation studies have ever been carried out to separate calcium carbonate particles from calcium sulfite or calcium sulfate particles, it was first necessary to select a suitable collecting reagent. Based on Zeta-potential studies, the most suitable reagent was found to be an octadecylamine-octadecylguanidine complex. Results are presented for flotation of calcium carbonate from scrubber sludge using this reagent, in a reverse-flotation process. The best results were obtained when the sludge was first pre-cleaned using a water-only cyclone to remove unfloatable coarse limestone, followed by froth flotation to remove fine limestone.

Jan 1, 1998

By D. J. Kunz

Myanmar Ivanhoe Copper Company Ltd. (MICCL) has been operating the Sabetaung- Kyisintaung (S&K) Project producing LME Grade A Copper Cathode using the Heap Leach-SX-EW Process since 1998. The mineralization is mainly Chalcocite and the mine has a life of 20 years at the designed annual production of 25,000 tonnes of cathode copper. Design capacity was achieved within two of months of start-up. The mine is among the world’s lowest cost, Heap Leach-SX-EW operations. Information regarding plant design and operation are presented along with the challenges lying ahead and the latest developments. Daniel Kunz is President and Chief Operating Officer of Ivanhoe Mines, and a director of MICCL. He has more than 20 years’ experience in mining, construction and engineering. Prior to joining Ivanhoe Mines in 1996, Mr. Kunz was Vice President and Controller of Morrison Knudsen Corporation, a major international mining and construction company. He was also President and Chief Executive Officer of MK Gold Company, a public mining company listed on NASDAQ.

Jan 1, 2001

By Reginald Dias

Mining operations take a tremendous toll on equipment, operating in difficult conditions day after day. Owners and operators cannot make the job any easier, but they can give their equipment an advantage. Equipment life may be extended through preventive maintenance and the proper application of quality lubricants. This means lubricants that are made to last longer and stand up better to the punishment mining equipment must endure. There are several practices to consider as part of a successful preventive maintenance program. A good place to start is to review original equipment manufacturer recommendations about servicing and maintenance intervals for each part of the equipment, especially the engine. If these recommendations have not been followed, owners and operators must begin periodic service work on equipment to help minimize equipment down-time and extend engine life.

Jan 1, 2003

By Caroline Gerwig, Joseph R. Wickline, Zach Agioutantis

In longwall mining, the progressive caving of the roof allows stored energy to dissipate over an extended time. However, in some cases, the roof strata above the longwall panel are unusually strong and do not break with the movement of the working face. Instead, the roof material bridges over the expanse of the longwall, forming an unstable beam. Later, when this beam breaks, the stored energy can release suddenly, causing a seismic event to propagate to surrounding mine workings. The focus of this paper is to estimate the size of beams that form over longwall panels to the seismic energy recorded by the mine. Analytical calculations are used to verify two-dimensional models of longwall roof beams to determine the strain energy and gravitational energy developed, which is then released upon strata failure to surrounding mine workings. Models are developed using RS2 to model the stress, strain, and deflection along the bottom of the longwall roof beam to calculate gravitational and strain energies. Gravitational energy is shown to be the main driving factor in energy release, except for the beams with low heights. Analyses allow the determination of beam characteristics based on seismic data. The analysis is refined using swelling factor to compare various beam drop heights. The models show an increase in seismic magnitude for higher drop heights. However, the actual data provided by the Buchanan mine displays a decrease in seismic magnitude with increasing drop height, indicating that energy is dissipated into the broken gob material as drop height increases.

Jul 1, 2023

By A. Moharana

A massive slide at Bingham Canyon wiped out a side of the pit and covered the main haul road in and out of the pit. All pre-slide mine designs and schedules were no longer valid. New designs and schedules needed to be developed quickly to provide management with information regarding the immediate post-slide production potential and the time needed to ramp back up to full production. At the time of the slide, an effort was already underway to convert Bingham?s in-house Medium Term Scheduling Process to MineSight®?s Schedule Optimizer (MSSO). One of the main reasons for doing this was to reduce the time needed to produce Medium Term Schedules at Bingham, which involves a complex shovel-based scheduling approach with shovel productivities based on shovel type and the types of mining cuts to which the shovel is assigned over each planning period. The objective of the schedule was to maximize shovel usage, satisfy mill feed requirements of four SAG mills with variable milling rates, and have flexibility in setting truck constraints. This paper will describe how the new MSSO-based mine scheduling process met the challenge of producing new schedules for Bingham in a minimal amount of time.

Feb 23, 2014

By W. D. Monaghan

One of the major ignition sources of fires and explosions in underground U.S. coal mines is flame cutting and welding. On May 20, 2006, a flame-cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On Jan. 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame-cutting and welding operation at the Loveridge Mine caused a fire that required sealing the mine for an extended period. On March 19, 1992, an explosion initiated by welding at the Blacksville No. 1 Mine resulted in four fatalities. These examples of mine incidents demonstrate the need to conduct research to develop best practices for safely conducting flame cutting and welding in underground coal mines. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame-cutting and welding operations to determine the root causes of these types of incidents. The methodology included interviewing mining personnel who perform flame-cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations. In addition, MSHA reports of investigations and accidents statistics were analyzed. The findings were used to identify and compare differences between flame-cutting and welding practices and techniques in small and large mines, eastern and western mines, low-seam and high-seam mines, room-and-pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices were developed to reduce the number of ?res and explosions caused by flame cutting and welding. This paper provides a summary of this research.

Jun 1, 2010

By V. Herman, B. Knorr, D. Whalen

"Edge effect is a condition widely observed in High Pressure Grinding Roll (HPGR) operations that gives rise to reduced comminution at the edges of the roll surfaces. This effect is caused by a reduction in the local crushing pressure at the edges of the rolls resulting from the sliding friction between the static cheek plates and HPGR feed material. Practically, this has an impact on equipment sizing, as the edge effect leads to coarser particles reporting to downstream equipment in open-circuit operations and increased circulating load and diminished HPGR circuit capacity in closed-circuit operations.To address this, Metso's HRC™ HPGR incorporates an Arch-frame to maintain a parallel relationship between the rolls and allow for the use of a flanged roll design. We conducted a series of pilot-plant tests with a 750 mm by 400 mm HRC HPGR to compare the performance of the flanged roll design against that of a traditional cheek plate arrangement under similar operating conditions. The edge effect was found to be significantly reduced with the flanged roll design. Based on the pilot-plant results, the implications for circuit design, energy efficiency and overall plant performance in a full-scale application were investigated and discussed.IntroductionGlobal trends such as lower ore grades and rising operating costs are driving the market toward more energy-efficient mineral processing solutions, most notably in comminution circuit design. High pressure grinding rolls (HPGRs) have been recognized as an energy-efficient solution relative to more conventional circuit designs. The basic operating principle of HPGRs, in which a fairly uniform pressure is applied to a bed of material in the compression zone, lends itself to this improved energy efficiency (Morley, 2006). Studies have estimated that savings of 10-15 percent are possible when comparing an HPGR circuit with a traditional SABC circuit (Rosario and Hall, 2008). While HPGRs offer a more energy-efficient solution than tumbling mills, there is still room for improvement in many aspects of the design. Edge effect, in particular, is one such aspect that limits the effectiveness of the machines. Edge effect is the impaired performance at the edge of the rolls due to a reduction in crushing pressure (Morley, 2010; van der Meer, 2010). As described in our prior work (Knorr, Herman and Whalen, 2013), edge effect is caused by the interaction between the ore entering the crusher and the relatively static cheek plates positioned at the edges of the rolls. As the material is drawn into the crushing zone, the sliding friction between the ore and the cheek plates inhibits the ability of material to be effectively drawn into the compression zone at the edges of the rolls. This reduces the crushing force in those edge regions relative to the center of the roll where material is being drawn into the compression zone at a higher rate. In addition, the cheek plates of a traditional HPGR design are held in place by spring-loaded brackets that are adjustable to manage the clearance. This spring-loaded cheek plate design prevents full compression of the material in the edge regions of the roll as there is relief at the outer edges."

Jan 1, 2016

By Clinton Birch

The multiple-criteria decision analysis is a technique that helps to find an optimal solution by evaluating conflicting criteria. In this study, an approach to perform multiple-criteria decision analysis for cut-off grade optimization, which considers the diverse stakeholder groups prevalent in the mining industry, is presented. The optimization model developed in this approach links the resource block model to the financial model, enabling the process to either maximize profit, net present value, revenue to the State, or extend the mine's life. To identify the optimal cut-off grade in each case, the Excel Solver function is utilized. Although it has limitations, the Solver function can still be modified to handle models with thousands of block values for determining input variables based on the target value. Following stakeholder engagement and dialogue, a single weighted average cut-off grade can then be determined. This approach is demonstrated for nine South African Witwatersrand gold mines.

Jun 25, 2023

By J. Z. Cheng

The extraction of thorium from industrial radioactive wastewaters discharged from Rare Earth (RE) plants was studied by the liquid membrane emulsion technique using P507- Span80-sulphonating kerosene-HCl. The emulsion conditions, the technological factors such as ratios of oil to the internal aqueous phase and water to emulsion, and the extraction time etc. were investigated.

Jan 1, 2008