Search Documents

By Timothy W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (?water box?) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 percent reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2010

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

By Charles Vaught, Jeff Duncan, Michael J. Brnich, Lisa J. Steiner

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.3 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Remote control and extended cut miner operators and face crews Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Remote control mining procedures including remote control mining, taking extended cuts, resetting breaker on mining machine, and setting timbers. Communicating mine conditions, influencing safe behaviors when mine conditions are less than stable Location: Underground coal mine, four section continuous mining operation Average seam height is 48 inches Problem: Your regular job is on the general labor crew at Cripple Creek #9 mine, a four section continuous mining operation. The mains are 9 entries wide and panels are 5 entries across. You and the rest of the crew had annual refresher training about 3 months ago. For the past few days you have been sent to 2 South panel to fill in as the third shuttle car operator. This morning, however, your buggy is down. The face boss asks you to get the scoop and take seven or eight timbers to the number 5 entry because the last shift got off sight line. The miner will be working in entry 5 while the bolter crew pins entry 4. When you get up to the face you see that Mo, the remote control continuous miner operator, has rounded off the left inby corner in order to make his first cuts in the right hand rib. Now, he has squared around enough so that you and Red, the miner helper, can set some posts on the corner. The two of you set posts along the left inby rib of #5 entry while the shuttle car operator waits. You are in a tight spot when Mo decides to start mining. You must decide where the best place is to stand for safety and to be out of the way.

Jan 10, 1999

Greater mining productivity requires a more efficient cutting process. The cutting force available from today?s mining machines has been optimized with respect to machine size and weight. Researchers have shown that when employing water-jet-assisted cutting, bit forces and drum torques can be reduced significantly, which may allow mining machines to become lighter and more efficient. The Bureau of Mines has initiated a program to develop a water- jet-assisted rotary cutting system using the conventional bit assisted by a directed water jet operating at moderate pressures (3,000 to 10,000 psi). This water-jet-assisted cutting system has the potential to improve cutting efficiency without increasing machine horsepower or water usage (beyond what is presently used for dust control) or requiring fundamental changes in mining practice. IR addition to improvements in productivity, other anticipated benefits of water-jet cutting include reduced generation of respirable dust, elimination of frictional ignitions, increased bit life, reduced fines, and fewer machine vibrations. The papers presented at this open industry meeting discuss the development of water-jet-assisted cutting technology and future application of this technology to a variety of mining techniques including roof drilling and longwall mining.

Jan 1, 1985

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscilloglaph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By J. D. Davis

The carbonizing properties of No. 2-bed coal from the Bartoy mine and No. 5- or Miller-bed coal from the Wilkeson-Miller mine, both at Wilkeson, Pierce County, Wash., were determined by the Bureau of Mines-American Gas Association (BM-AGA) method. Tests were made in the 13-inch retort at 500°, 600°, and 700° C. and in the 18¬inch retort at 800°, 900°, and 1,000° C. Fischer low-temperature and United States Steel Corporation high-temperature assays were made and the results compared with those of the BM-AGA tests at corresponding temperatures. Agglutinating and plastic properties were determined, and chemical and petrographic analyses were made. The No. 2 bed is 58.5 to 88.0 inches thick at three points sampled in the Bartoy mine. The coal is 98 percent bright and contains only a trace of fusain. A composite of three mine samples contained 13.8 percent ash. The washed sample, which was used in the tests described herein, contained 11.4 percent ash, 2.2 percent moisture, and 0.6 percent sulfur upon the as-carbonized basis and 68.4 percent fixed carbon upon the dry, mineral-matter-free basis. The heating value was 15,183 B. t.u. per pound upon the moist, mineral-matter-free basis. No. 2 therefore ranks as a high-volatile A coal and is very high in that, rank. The ash softens at 2,910° F. Except for its ash content, which is higher than the limit of 9.0 percent specified by the American Society for Testing Materials, No. 2 coal fulfills the requirements of a coking coal. It also is classed as extremely friable, the friability being 88.0 percent. The agglutinating index (7.6 for the 15 : 1 ratio of silicon carbide to coal) is high, and the plasticity as indicated by the Gieseler test (60 divisions per minute) is low for a high-volatile A coal.

Jan 1, 1942

By R. R. Sayers

Mine operators and managers for a number of years have known that the maintenance of health among the workers has an appreciable financial value, In order to maintain the health, it has been found ne cessery to imow; 1. The health hazards existing in the industry as a whole and the specific hazard in the individual mine. 2. The physical condition of applicants for employment as well as that of the old employees. This can be determined only by systematic physical examination of all applicants and of regular employees at intervals of at least once a year thereafter. 3. All cases of sickness that occur among the workers. No operator or manager, or personnel, medical, or safety organization can control or prevent sickness without knowing where, when, and under what conditions the sickness actually occurs. In order to obtain information as to the hazards of industry, investigations have been and are being made of the effects of the condi- tions both in the field under usual working practices and in the laboratory. In the field several factors are generally present which affect the health. The effect of these factors may be determined by studying each of them separately in the laboratory. However, both the field and the laboratory studies are limited in value in that such studies usually have been made over a comparatively short period. While we have some information as to their immediate effect, we do not know to what extent extreme heat, humidity, the presence of dust or other health hazards are the cause of disability. Mortality statistics are probably the most easily available indices as to the hazards of industry. As an example, a study of such statistics among coal miners of Indiana shows a marked increase in the death rate in 1918.

Mar 1, 1923

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscillograph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By Mark S. Redfern, Kim M. Corneliusa, Christopher A. Hamrick, Sean Gallaghera

Coal miners often handle heavy electrical power cables, weighing up to 10 kg per meter. These cables are manually lifted and attached to the mine roof to prevent damage from mobile underground equipment. Data suggest that workers who commonly perform cable handling tasks experience a high rate of lost time back injuries. In this study, six male underground miners performed a total of 12 cable-hanging tasks in standing, stooping, and kneeling postures, during which kinematic and ground reaction force data were collected. Reductions in vertical work space were found to result in a linear increase in the peak moment experienced by the lumbarspine (p<0.05). In restricted postures, peak moments were not significantly different in stooping vs. kneeling postures (p>0.05). Average lumbopelvic flexion during the tasks was highest in stooping conditions, followed by standing and kneeling exertions (p<0.05). Implications of this data with respect to design of cable handling tasks are presented and discussed. Keywords: Biomechanics, posture, low back pain, restricted workspace, mining

By Marvin W. Wilson

The Federal Bureau of Mines has conducted laboratory experiments simulating underground gasification of coal to study the feasibility and mechanism of the process and determine the chemical and physical characteristics of a coal-bed during gasification. Laboratory and small-scale field experiments also were made to investigate the properties of coal and other factors affecting the electrolinking-carbonization method of preparing a path through a coalbed before gasification. Laboratory experiments simulating underground gasification of coal: Experiments with a laboratory retort indicated that bituminous-coal deposits could be gasified in place to produce a combustible gas.

Jan 1, 1960

By Richard W. Knostman

A study was made of the factors affecting lead and zinc production in the Pacific Northwest. Costs, ore reserves and potential resources, and domestic demand were analyzed. It was concluded that a projected 3.1-percent average annual increase in U.S. demand for zinc through 1975 and a corresponding 2.5-percent rise for lead will be supplied mainly from mines in the Eastern and Central States. Annual Pacific Northwest mine production of lead is estimated to fluctuate around 82,000 tons, while zinc output may average 135,000 tons through 1975. Measured, indicated, and inferred reserves in the Pacific Northwest, containing 1.56 million tons of lead and 2.59 million tons of zinc, are more than sufficient to maintain this level of production. Annual production from Pacific Northwest electrolytic zinc plants is expected to increase to over 300,000 tons of slab zinc by 1975. Lead smelters may experience difficulty in maintaining output at 1964 levels.

Jan 1, 1967

By E. P. Youngman

The Siamese mining lew, which is cited as "The Sian Mining Act, 2461 (1919)," was enacted February 14, B. E. 2461 (A. D. 1919), corresponding to the ninth year of His Majesty's reign. This act replaces the Sian Mining Act of 1901 and repeals all edicts, decrees, laws, rules, and local customs relating to mining the terms of which are inconsistent with the new law. It shall in- clude all subsequent alterations or additions, as well as all rules issued by the Minister (of Land and Agriculture) already in force or to be brought into force publication in the Government Gazette to be deemed sufficient notice of any modifications or alterations. (Art. 1, 2, 5, 83, and 85.) Legislation passed recently amending certain provisions of the mining law for the purpose of controlling the sale of minerals is the mining amendment act, B. E. 2474, given August 21, 1931 (7th year of the present reign), which repeals provisions of the mining act, B. 3. 2461, and also all rules and regula- tions relating to mining that are inconsistent with the amending ect. Under article 25 of the mining amendment act, B. E. 2474, ministeriel regulations (of the Minister of Agriculture) were issued August 21, 1931. Further recent legislation, brought about by the agreement of the Siamese Government to become a party to the international tin restriction scheme (inter- national tin pool), is the tin and tin ore restriction act (Siam), B. E. 2474, which came into force on September 1, 1921, its purpose being to suspend the

Mar 1, 1933

By Diane M. Doyle-Coombs

In late July 1985, air samples from a sealed portion of the Quinland coal mine in West Virginia showed the presence of carbon monoxide (CO). Mine Safety and Health Administration (MSHA) personnel concluded that a fire was burning behind the seals. Since an imminent danger existed, the mine operator was given a closure order. The gases behind the seals were monitored and almost 2 million ff of carbon dioxide (C02) gas was pumped into the sealed area to stabilize the environment. Sixteen days after the closure order was issued, MSHA allowed the mine to return to production. Approximately 1 yr later, mine management submitted a seal breaching request to MSHA in order to drive a set of entries to further develop the mine. The Bureau of Mines established a sampling strategy and monitored gases from behind the sealed area during the breaching operation until the atmosphere was safe. This report is an account of the seal breaching conducted by the mine, MSHA, and the Bureau. The logistics of this event, the sampling strategy, and the equations applied could be used by the mining industry in future breachings or mine recovery operations. Time to reenter the area was calculated by using the methane (CH4) concentrations sampled at the discharge of the seals. Tracer gas was used to verify the ventilation flows through the area.

Jan 1, 1988

By J. A. Kost

The objectives of this contract were to determine the amount, size, and deposition of float coal dust (74 x 10 microns) generated during the mining and transporting of coal in underground U.S. mining operations. Rock dust distributed by trickle dusters was also sampled. In addition to four belt-transfer points, two continuous and two conventional mining sections were sampled at five mines located in Pennsylvania, West Virginia, Kentucky, and Illinois. Float-dust samples were collected on deposition pans; total airborne dust was collected with MSA Model C personal samplers equipped with Unico filter casettes; Andersen cascade impactors provided relative size distributions of the samples. Production, airflow, and water flow were monitored to examine their effect on dust levels.

Jan 1, 1981

By Manuel Gomez

A lignite from Milam County, Tex., has been oxidized by air at temperatures from about 27° to 300° C. for varying lengths of time. The oxidized coal was carbonized at 500° C. in a laboratory assay unit, and the products of carbonization were measured and analyzed. The data presented suggest that, as lignite is progressively oxidized, tar yields are decreased and gas yields are increased in a ratio approximating 1:1. It is surmised that tar-yielding structures in the nonoxidized coal produce gas, principally, when the coal is oxidized. Char-yielding structures of the nonoxidized coal give rise to additional water of decomposition after oxidation and pyrolysis. As lignite is subjected to greater oxidation, the gaseous product evolved on pyrolysis becomes almost entirely carbon dioxide. Tar yields decrease with an increased degree of oxidation, so that the reduction in tar yield may be used as a qualitative measure of oxidation. Pilot-plant drying and carbonization, where air is used as the transport gas and where some air is included in the drying and carbonizing gases, induces some oxidation of the coal particle. The short residence time in a fluidized system with reference to the oxidation environment limits the oxidation.

Jan 1, 1956

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

Unlike other types of mining accidents, where an incident generally involves only a few workers, the danger of a mine fire extends to every person working in the underground environment. Mine fires can trap or kill those working underground by blocking avenues of escape and rapidly creating heat, asphyxiating gases and toxic fire products that can quickly spread throughout the mine. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate and improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Because wood is the second most abundant fuel available during a coal mine fire, it was decided that a series of large-scale wood crib fire tests was needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.1

By H. E. Powell

The magnetic susceptibility, the geographical source, and associated minerals are given for 44 copper-, 26 lead-, and 19 zinc-bearing minerals. Of the 44 copper minerals/ all had a susceptibility of less than 15 X 10-6 cgs, and about 20 percent of them were diamagnetic. Of the 26 lead minerals, all had a susceptibility of less than 11 X 10-5 cgs, and almost half of them were diamagnetic. And, of the 19 zinc minerals, all except four had a susceptibility of less than 9 X 10-6 cgs, and about one-fourth of them were diamagnetic.

Jan 1, 1968

The selective placement of coal stripmine overburden is examined. Physical and chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions or similar problems. Five mining methods already used in the industry, that are capable of selectively handling waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons are made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided. This volume contains all Appendices to the report.

Jan 1, 1981

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground nine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.8 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated. Rock dust was employed chiefly in the larger mines, which numbered only 431 out of 6,016 underground mines in operation in 1935, according to reports from mining companies. The mines in which rock dust was used had an average of 288 underground employees per mine, whereas mines in which rock dust was not used averaged only 62 underground employees per mine.

Jan 1, 1940

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground mine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.9 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated.

Jan 1, 1940