Search Documents

By Sean Gallagher, John R. Bartels, Dean H. Ambrose

Remote operation of continuous miners has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred when using remote controls. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory examined the workplace relationships between continuous miner operators and various tramming modes of the equipment using motion captured data, predicted operator response times, and field- of- view data to determine causes of operator-machine struck-by events in a virtual mine environment. Factors studied included machine speed, direction of escape, operator facing orientation relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck. It is hoped that this data will provide an improved rationale for operator positioning for remotely operated continuous miners.

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

By W. T. Millar

"INTRODUCTION The purpose of the Star Lake project was to investigate, by geophysical surveying and diamond drilling, the magnetite deposits in the northwestern Adirondacks, the ultimate objective being to increase iron production in eastern United States,ACKNOWLEDGMENTSIn its program of investigating mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclu-sion. The Mining Branch, Lowell B. ""Moon, chief; conducts preliminary examinations, performs the actual investigative work, aid prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The chemical and spectrographic analyses included in this report were performed at the Eastern Experiment Station of the Bureau of Lines at College Park, Md., under the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and under the immediate direction of Dr. Alton. Gobriel in charge of the laboratory service unit.The mineral exploration was under the general supervision successively of John D. Bardill, district engineer, and McHenry Mosier, chief, College Park Division, Mining Branch. The work was done under the immediate supervision successively of J. P. Ryan, N. A. Eilertsen, and W. T. Millar, project engineers."

Sep 1, 1947

By P. B. Grote

The report provides a general description of DOM technology, sources for DOM technology, and identifies approaches and requirements for acquisition by the Enterprise of DOM technology by conventional means. The approaches identified assume the Enterprise enters into a contractual/ joint venture arrangement with an uncommitted and competent systems management firm at various stages of the DOM system acquisition process. The approaches provide for training through work/study as well as through direct participation in acquisition programs. The potential success of the alternatives are evaluated in terms of the likelihood of the acquisition of an ongoing Enterprise economic DOM operational capability. The study concludes that sources exist and that the Enterprise should under-take the development of its own technical capability through conceptual design prior to selecting its source for systems management expertise.

Jan 1, 1980

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

By Terry R. Neumann

A mineral survey of the 23,760-acre Abert Rim Wilderness Study Area (OR-1-101) was conducted by the U.S. Bureau of Mines in 1986 at the request of the Bureau of land Management in order to evaluate its identified mineral resources. The study area is located in south-central Oregon, 26 mi north-northeast of Lakeview, OR. Federal and Lake County mining records indicate no mining claims, geothermal leases, or oil and gas leases within the study area as of January 1, 1987. No economic concentrations of minerals were found in the study area. The Wilderness Study Area is dominated by Abert Rim, a north-trending Basin and Range fault scarp that parallels the study area's western boundary. Exposed on the scarp is an approximately 2,000-ft-thick volcanic sequence consisting of Oligocene-Miocene basalts, tuffs, and tuffaceous sedimentary rocks.

Jan 1, 1987

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1974 is compared with consumption in 1973 and 1975 (preliminary data).

Jan 1, 1977

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

By Charles D. Wood

"Selected Topics,? in reviewing the control of emissions from diesel engine powered equipment used in underground mining, explores these fields of interest: hydrogen as fuel; lubricating oil as a source of particulates; applicability of stationary source scrubbers; worldwide diesel exhaust scrubbers; instrumentation technology for measurement of N02; control of emissions through application of sensors and microprocessors; use of fuel additives; technology transfer of marine diesel practice; technology required to use 4-stroke, aftercooled, turbocharged, direct injection engines; oxidation and reduction catalysts for diesel engine exhausts. "Selected Topics? makes recommendations for research and provides a bibliography and lists of references.

Jan 1, 1979

By Frank D. Lamb, Lloyg H. Baning

"The crushed-stone industry has long been troubled with the problem of producing a more or less cubical product for use as concrete aggregate. Its seriousness varies widely for each producer, depending upon the character of the rock employed for raw material and the ultimate use of the crushed stone. For many construction uses, such as the macadam or bituminous-concrete- type road, flat pieces are not objectionable and may even be preferable to more cubical rock. However, most specifications for concrete require that the stone must be reasonably free from flat and elongated pieces.The rigid specifications set by many contractors have resulted in the rejection of coarse aggregate that, except for the presence of an excessive amount of flat and elongated pieces, would be entirely acceptable. In many instances, if an efficient, economical method of removing flat and elongated pieces were available, local producers could meet the requirements of the contractor and thus eliminate the necessity for importing more cubical material.A brief investigation of the problem of removal of flat and elongated pieces from crushed aggregate, carried out at the Eastern Experiment Station of the Bureau of Mines, indicated that it is mechanically possible to remove flat pieces from crushed rock.TEST EQUIPMENTA number of mechanical devices are used by the coal industry for separating slate from coal; these depend upon the difference in shape of the crushed slate as compared with the coal. Such devices as shutter screens, spiral separators, and the Norman picker would be suitable for removing flat pieces from crushed rock in the same manner as they are used by the coal industry. None of these devices was immediately available for testing purposes, so an attempt was made to construct a simple device that could be used in commercial operations."

Sep 1, 1944

This chapter presents proportionate mortality ratios (PMRs) derived from death certificate data in the National Occupational Mortality Surveillance (NOMS) database for the years 1986 through 1993. At the time this report was prepared, 1993 was the latest year for which data were available. Industry is classified under the 1980 U.S. Bureau of the Census classification system [Bureau of the Census 1982]; cause of death, under the International Classification of Diseases, Ninth Revision (ICD-9) [World Health Organization 1977]. A PMR of 100 indicates a mortality risk for a particular industry group that is similar to that for all industry groups combined. A PMR over 100 suggests a higher risk; a PMR under 100 suggests a lower risk. PMRs are subject to many factors that affect their reliability and validity and may not be comparable across populations with very different causes of death. An elevated PMR for a specified cause of death among an occupational or industry group may indicate a relationship between a work exposure and the cause of death specified. However, there are many limitations of PMRs as a measure of risk; they are most useful for generating hypotheses about exposure-disease relationships, which can then be tested in other studies. Selected PMRs are presented separately for males and females for coal mining, metal mining, nonmetallic mineral mining and quarrying (which includes nonmetal, stone, and sand and gravel), and for oil and gas extraction. All PMRs have been adjusted for age and race. In general, PMRs are presented only if the lower 95% confidence limit exceeded 100. If a PMR in an ICD-9 subcategory was above 100, however, the PMR for the larger category into which the subcategory falls is always presented and may be less than 100. PMRs can be expected to be elevated for conditions that have a high prevalence in particular occupational groups. PMRs showed elevated values for conditions known to affect miners, such as coal workers' pneumoconiosis, pneumoconiosis due to silica, tuberculosis, chronic pulmonary heart disease, and injuries. Additional findings of interest were- • An elevated PMR for myocardial infarction among male coal miners (table 2-1); • Elevated PMRs for neurologic disease in general and anterior horn cell disease, in particular among male metal miners (table 2-3); • An elevated PMR for rheumatic heart disease in male metal miners (table 2-3); • Elevated PMRs for malignant neoplasms of the digestive organs and peritoneum and for malignant neoplasms of the colon and rectum in female nonmetal miners (table 2-6); and • Elevated PMRs for non-A, non-B hepatitis and arteriosclerotic heart disease among male oil and gas workers (table 2-7).

Jan 5, 2000

By Paul R. Thomas

The Bureau of Mines evaluated the impact of the depletion allowance upon the economic availability of copper from domestic deposits. The potential long-run percentage depletion deduction, cumulated over the life of the properties, was estimated at approximately $2.5 billion for producing properties and up to $11.7 billion for nonproducers. The income transfer, in the form of higher Federal income tax payments if the allowance were repealed, was estimated at $1.5 billion for producing properties and up to $8 billion for nonproducers. The percentage depletion allowance, through its role in determining Federal income tax liability, was found to be very significant in affecting profitability. Repeal of the allowance could result in major domestic copper availability reductions at all price levels, now and in the future, as a result of reduced profit margins for current producers, and postponement of development decisions for nonproducers. It was demonstrated that a 50-percent reduction in the percentage depletion rate applicable to copper would also result in a significant decrease in profitability for nonproducing properties. For producing properties, the percentage depletion rate on copper was shown to be less significant than the income limitation that is placed upon the total amount of the depletion deduction. Repeal of the minimum Federal tax provision was shown to be significant in enhancing profitability for both producing and nonproducing deposits. The report concludes that the percentage depletion allowance operates as an important method of capital recovery and production incentive.

Jan 1, 1982

By M. R. Geer

Efforts to evaluate washery performance are nearly as old as the art of coal cleaning, and in former years there was no uniformity in either the methods used or the basic terminology employed. This situation, and the con- fusion it bred, prevailed until about the time of the First International Coal Preparation Conference in 1950, Largely because of the interest of the French coal research organization Cerchar, the subject of evaluating performance was given prime importance at this conference. As a result, there is now a much greater degree of uniformity in terminology and methods of expressing cleaning results. The International Standards Organization currently is working toward international standards of terminology and methods that should improve the situation even more. The various criteria that are used to evaluate the performance of coal- cleaning equipment fall into three categories, depending upon the extent to which they are dependent on the density composition of the raw coal; some are directly dependent, others are only indirectly dependent, and still others are substantially indenpendent.

Jan 1, 1962

By M. H. Kline

The Cranberry magnetite deposits occur in pre-Cambrian granite-gneiss, in a belt extending from 3 miles southeast of Cranberry, N. C., to about 6 miles southwest of Magnetic City, Tenn. The belt forms a curve) elongated to the north, approximately 26 miles in length. The Bureau of Mines investigation has been confined to the eastern part of the belt, comprising the area from Fork Mountain, Avery County, N.C., to the Hcupscup Knob prospects in Carter County, Tenn. The deposits were worked at least us early as 1820. The Cranberry Iron & Coal Co. and its successors operated the Cranberry mine intermittently for about 50 years until 1930, when operations were abandoned.

Jan 1, 1948

By E. G. Valdez

Three cryogenic systems that utilized liquid nitrogen, dry ice, and methanol with dry ice were investigated in conjunction with crushing and classifying techniques. The systems were used to aid in separating and reclaiming the metallic components contained in insulated wires, shredded automobile nonferrous metal concentrates, small motors, generators, and rubber tires. Wire strands, 2 to 6 inches long and insulated with polyvinyl chloride and neoprene, were chilled at -60° and -195° C, then roll-crushed and processed by water elutriation; this procedure resulted in two products--a sink fraction that was 99 percent metallic and a float fraction that was 99 percent nonmetallic. Excellent separation of zinc die-casting alloys from copper and aluminum contained in shredded automobile nonferrous metal concentrates was attained by chilling at -72° C for 1 minute, crushing in a grateless hammer mill, and screening. From the screened products, 97.2 and 100 percent of the copper and aluminum, respectively, were recovered in the plus Pinch fraction, and 100 percent of the zinc was recovered in the minus 1-inch fraction of over 97 percent zinc die-cast purity. Laboratory experimental results comparing direct and indirect chilling indicated that a sufficiently low temperature could be attained by indirect chilling to permit use of a liquid C02-dry ice system on insulated wires and mixed nonferrous metallic concentrates.

Jan 1, 1973

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By James C. Barker

Unverified reports of rare earth element (REE) concentrations in gold placers and radioactive mineral prospects in the Zane Hills were investigated by the U.S. Bureau of Mines as part of the Alaska critical minerals program. REE is reported to occur in dredge concentrates at the Hogatza mine and up to 1.2 pct REE was previously analyzed in alkalic syenite (bostonite) dikes marginal to the pluton. In addition, numerous thorium-rich veins, explored for their uranium content but unevaluated for REE, occur on the western margin of the Zane Hills. The Bureau mapped and sampled all of the reported or suspected REE occurrences. Dredge concentrates contain abundant uranothorianite, a mineral species which incorporates cerium subgroup REE. Bostonite dikes occur in conjunction with a multi-phased zoned alkalic intrusion, however, no significant REE concentrations were found. Thorium-rich veins contain nil to 0.5 pct Y but resource potential is limited by this relatively low grade, the ultimate low tonnage potential, and the lack of uranium as a major economic element. The Zane Hills exhibit attractive exploration targets for uranium deposits, primarily in a sedimentary form. Gold may be found peripheral to the pluton in both placer and lode deposits. Resource potential of REE, however, appears limited to a placer by-product of REE-Zr-Ti that is recoverable only during large scale gold placer mining. Placer exploration of the lower Wheeler and Dakli Creeks is suggested.

Jan 1, 1991

By Carl Belser

This paper, covering Chaffee, Fremont, Gunnison, Lake, Larimer, Park, and Summit Counties, Colo., is the second of a series reporting on the tungsten potential of the Colorado region. The assembled information was obtained by examination of some properties, personal contacts with owners, and access to unpublished reports by other engineers. The tungsten-bearing areas of the 7 counties cover approximately 400 square miles and are in 10 distinct areas, which vary in size (fig. 1) from 1 square mile up to 290 square miles. The tungsten mineral wolframite was discovered by a man named Hackay near Dale on the Florence & Cripple Creek Railroad in the early 1900's, and wolframite and hubnerite were noted at Climax and the adjacent areas in Lake and Summit Counties at an early date, but no records of shipment from any of the areas are available before World War II. It is not known when scheelite was first discovered, but it was recognized in the Stockton mine during World War I. In the counties listed 64 properties are known to contain tungsten; of these, 18 have had some commercial output, although only 3 of them produced in 1953. The total production through 1953 is estimated at 115,000 short-ton units of tungsten trioxide. In 1953 by far the major portion came from the Climax mine.

Jan 1, 1956

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984