Search Documents

By Franklin H. Persse

The Bureau of Mines estimated reclamation costs for 13 surface coal mines in nine States west of the Missisisppi River. With the exception of the Pacific Coast coal province, at least one mine in each of the western coal provinces was studied. Cost estimates were, made using standard estimating procedures from data obtained from company records, interviews with industry personnel, and onsite observations. Estimated costs are presented in four categories which represent the four phases of mined-land reclamation: (1) Design, engineering, and overhead; (2) bond and permit fees; (3) backfilling and grading; and (4) revegetation. Estimated costs as of the first quarter of 1976 are expressed as averages and ranges in terms of per acre, per ton of coal produced, and per million Btu. Total reclamation costs ranged from $860 to $7,200 per acre, from 6 to 84 cents per ton, and from 4 to 35.3 mills per million Btu. A mine in the Northern Great Plains coal province (Region D) showed the highest per acre cost whereas mines in part of the western region of the Interior coal province (Region A) experienced the greatest per ton and per million Btu cost. The high cost of reclamation in the Western United States is reflected in the backfill in and grading category, particularly in the cost of topsoil removal and subsequent replacement as required by individual State reclamation regulations.

Jan 1, 1977

By Michael G. Zabetakis

The spillage of liquid diethyl ether in rooms at floor level and 3 feet above the floor resulted in flammable vapor-air mixtures in the immediate vicinity of the exposed liquido The liquid temperature was found to decrease by as much as 35° C., with a resultant decrease in vaporization rate. A search of the literature yielded numerous references to unstable peroxide (residue) formed by the autoxidation of ether. Such residues appear to constitute an explosion hazard in the condensed state.

Jan 1, 1962

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By J. W. Thompson

RAILROAD GRANT-MDIERALS. Diatomaceous or infusorial earth when found in such quantity and quality as to render lands containing deposits valuable therefor are mineral lands within the meaning of the mining laws and must be excepted from grants to the Central Pacific Railway Company. Central Pacific Ry. Co., In re, 45 Land Decisions, 223, p. 226. RAILROAD GRANT-CLASSIFICATION, If any evidence of minerals is found upon lands within a railroad grant and the showing is sufficient in the opinion of prudent and qualified persons to warrant further exploration and expenditure, with reasonable prospects of success, then the land can not be classified as nonmineral and is not subject to the grant to a railroad company. But where there is no present indication of minerals nor any geological evidence upon which to base a mineral finding, land should not be classified as mineral, or held for further classification and reserved from the railroad's grant, upon the surmise that future prospects might disclose evidences of minerals. Southern PacUl.c Ry. Co., In re, 45 Land Decisions, 326, p. 329. INDEMNITY SELECTION BY RAILWAY COMPANY, Under section 3 of the act of July 2, 1864 (13 Stat., 365), and the joint resolution of May 31, 1870 (16 Stat., 378), the Northern Pacific Railway Company could take coal and iron land within its primary or grant limits. It could not base an indemnity selection upon the claim that certain land was coal or iron in ;;haracter, as such land was not lost to it as part of the grant. But the company was authorized to select other lands in lieu of those lost because of their mineral character, but the word "mineral" did not include iron or coal, and, accordingly, the railroad company was entitled to take coal lands under its indemnity selection.

Jan 1, 1917

By R. E. Morgan

This publication presents abstracts of articles and investigations pertaining to the utilization of fly ash. The terms "fly ash" and "flue. ash," as' used in most of the papers, refer to the ash from pulverized-coal firing collected by electrostatic precipitators or mechanical collectors. Several investigators do not define the material on which they report beyond calling it fly ash, but they probably refer to the fine material resulting from burning pulverized coal. A few of the papers report on investigations involving not only the use of fly ash but boiler slag as well. These can be identified by the title of the articles. Bibliographical information and the abstracts are arranged according to the date the papers were published, with the most recent listed first. With the continually increasing use of pulverized-coal firing, profitable disposal of the fly ash is becoming a problem of greater importance to many utility and industrial companies. Also, in recent years, the public demand for cleaner air, and the more highly efficient fly-ash collectors available have resulted in the collection of a greater percentage of the fly ash produced. The solution to better utilization of fly ash has, therefore, been the object of research for some years.

Jan 1, 1952

By L. H. Banning

This investigation was undertaken to obtain basic information necessary for the design and operation of a plant for recovering metallic values from nickeliferous laterite and serpentine of the Philippine Islands. It was divided into three parts: (1) Mineralogical studies and preliminary mineral dressing tests; (2) electric smelting of the ores, upgrading of ferronickel by blowing with oxygen, smelting laterite slag to produce crude iron, and the production of mild steel; and (3) nickel and cobalt recovery from upgraded ferronickel. Results of the investigation indicate that it should be feasible to recover nickel, iron, and possibly cobalt products from the laterite and ferro-nickel from the serpentine. Mineralogical studies were made on representative fractions of the laterite and serpentine tonnage samples and on five selected samples; mineral dressing tests were made only on laterite. The nickel occurs principally associated with hydrous iron oxides and chemically combined with serpentine; garnierite was the only discrete nickel mineral identified, and it was found in a highly decomposed serpentine. The bulk of the cobalt was found in wadlike manganese oxide material. Approximately twice as much chromite was found in the laterite as in the serpentine, By mineral dressing techniques, laterite was separated into two fractions: one fraction contained over 90 percent of the nickel and cobalt, and 83 percent of the iron; the other fraction contained 74 percent of the chromium. A cobalt concentrate (1.1 percent Co) was produced by a scrubbing and sizing procedure.

Jan 1, 1962

By John B. Goodman

A LOW-TEMPERATURE carbonization assay test is described, and factual data derived from this test are presented. The test procedure outlined in this report incorporates a mild-steel retort of improved design, an accurately controlled method of heating, and a complete collection and condensation system for the solid, liquid, and gaseous products of carbonization. The test described establishes, under closely controlled conditions, the relationship of temperature to yields of products on carbonization. Noncoking or weakly coking coals and other carbonaceous material are particularly amenable to testing by the assay. Mass balances of 100 percent± 0.3 are obtainable by this test. It is believed that the efficiency of the test and the accuracy of the type data obtained have been materially increased.

Jan 1, 1953

By W. E. Schroeder

Two underground installations of the sprayfan system are described and evaluated. The spray fan proves capable of reducing by 1300 percent downtime due to high methane. Spray fan face ventilation at 20 ft brattice setback is shown to give improved methane control over conventional sprays at 10 ft setback. In addition, this report describes: ? A simple method for determining the most economical application of ventilation for face methane control ? The effect of place variables (primary ventilation, auxiliary ventilation, seam height, etc.) on methane concentrations ? The correlation of methane concentrations with brattice setback. These results are utilized to suggest a safer and more economical approach to face methane control.

Jan 1, 1981

By Wesley T. Holmes

This report describes the first phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected slag compositions in the titania-alumina-silica-calcia-magnesia system. Both the melting-holding-quenching method and the hot-stage microscope method were used in the tests. Liquidus temperatures of slags studied ranged from 1,217° to 1,667° C. The lowest liquidus temperature of the slags occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. Liquidus temperatures were also lowered when Si02 was substituted for Ti02 plus Al2O3 when CaO and MgO levels were held constant. Improved methods for the measurement of liquidus temperatures on very small samples are described.

Jan 1, 1968

By Abdurrahman Cetinbas

The periphery of longwall panels in the Pocahontas No.3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray system.

Jan 1, 1974

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

Two coal seams were selected and the conceptual designs were based on the geological and physical conditions typical of these seams. As a result of the screening process presented below, the two coal seams selected were the Lower Kittanning Seam in central Cambria County, Pennsylvania and the Pittsburgh Seam in northwestern West Virginia and southwestern Pennsylvania. SELECTION PROCESS FIRST SCREENING OF LONGWALL OPERATIONS The list of longwall operations prepared in Phase I and included in the Phase I report, was used as the basis for a first screening. From this list it was determined which longwall operations were not in the Appalachian coal fields and not in a coal seam of the thickness range of 42 to 72 inches. The first screening eliminated 30 of the listed operations, leaving 48.

Jan 1, 1976

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pressure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water-treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to 5-ton pieces, a 150-ton batch-type retort was designed and constructed at the Bureau of Mines Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11 ½ feet inside diameter, and is supported in a 95-foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, was used as the test shale. To date, 11 runs have been completed, and the results of the last 10 of these are reported. The effects of oxygen content of the retorting gas and the superficial gas velocity of the retorting gas on oil recovery from a column of mine-run oil shale were studied. In one run, the average particle size of the shale was substantially increased to determine its effect on oil yield. Oil recoveries ranged from a low of 39.3 to a high of 65.8 volume-percent of Fischer assay.

Jan 1, 1974

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical -problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By D. D. Southworth

In 1981, 1982, and 1983, the Bureau of Mines examined the potential for lode deposits of platinum-group metals (PGM) in the Goodnews Bay ultramafic complex, Alaska. The complex consists of the Red Mountain, Suzie Mountain, and Smalls River ultramafic bodies and displays concentric zoning of rock types similar to complexes in southeast Alaska, British Columbia, and the Ural Mountains in the U.S.S.R. Results of the study indicate that platinum is preferentially associated with chromite and magnetite in the dunite core of the complex, and palladium is preferentidlly associated with sulfide minerals in the outer clinopyroxene-rich zones. the most promising targets for PGM lode deposits are the chromite-rich dunite at the heads of Fox Gulch and Squirrel Creek and iron-nickel and iron copper sulfide-bearing magnetite clinopyroxenite and hornblende-rich rocks outward of the dunite core, also in the Fox Gulch-Squirrel Creek area. Significant placer reserves are present in the unmined, deeply buried placer ground in the lower Salmon River Valley, and also in tailings from previous dredging.

Jan 1, 2011

By F. W. Wood

The Bureau of Mines has sought clarification of the Ti-TiN system by studying the phases formed by diffusion reactions between titanium and titanium nitride. Reaction couples were prepared by embedding pockets of TiN powder in arc-melted buttons of titanium. Specimens were vacuum annealed at nominal temperatures of 800°, 950°, 1,200°, and 1,500° C. Metallographically mounted cross sections from reacted specimens and from some that were not annealed were examined optically, with an electron microprobe, with an election microscope, and by X-ray diffraction. Each annealed specimen contained a segregated core primarily of d-phase material, an ?-phase diffusion layer, an a-phase diffusion layer, and host metal. On the basis of corresponding microprobe analyses, and considering results of certain other research, a new phase diagram is proposed. It contains no qualitative innovations, only quantitative adjustments. Results were also analyzed from the viewpoint of diffusion behavior. Diffusion coefficients calculated for the ? phase were sufficiently scattered that the parameters are very tentative. Nevertheless, the diffusion behavior reported is in reasonable agreement with one of two prior studies if it is assumed that the earlier investigators were mistaken in their identification of the nitride phase in which the diffusion occurred.

Jan 1, 1974

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world output for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963