Search Documents

By Paul Downing

When was the last time the documents and paperwork were cleaned out of the glove boxes, door pockets, under the seats and above the visors in your company vehicles? Insurance cards that expired three years ago and vehicle registrations from 1999 through 2003, for instance, don’t do any good and just take up space

Jan 1, 2008

By Sushil Bhandari, S. S. Rathore

Controlled drilling and blasting continue to be an important method of block production and for block splitting. Drill and blast technique has disadvantage that sometimes, it produces cracks in uncontrolled manner and also produces micro cracks in the block as well as in remaining rock, if not carefully carried out. Recovery by this method is low compared to other methods. Therefore, attempts have continued to develop controlled growth of crack in desired direction. In this paper a series of tests are described using detonating fuse in marble. Economics of different methods is also compared. In comparison to conventional use when holes are lined with inexpensive cardboard or plastic liners with a slit, the cost and damage is the least and development of crack is in desired direction.

Jan 1, 2002

By Dale Preece, Stephen Chung, Qian Liu

Stoping is one of the widely adapted methods in underground mining. In this method, fanned or parallel holes are often drilled from a top sill down to a sub- level in the ore zone and blasted ring by ring into a stope for excavation. At Brunswick Mine of Canada, this technique has been used daily in conducting production blasts. However, when mining into the West Ore Zone, it has been identified strategically that a mass stope blast, involving the blasting of rock from the 3-sub level down to the 1-sub level, should be considered to ensure the safe operation and regaining of access to the trapped main ore zone. The challenge of this mass blast lies in the control of ground vibration and precise timing for blasting 800 holes drilled in six blocks from three different levels within 6.5 seconds, to allow sufficient void to be created in each level for the muck moving in order from the upper to the lower levels without bridging. This paper describes stope blast simulations using a discrete element computer code for modeling blast-induced rock displacement in conjunction with a precision electronic programmable delay timing system for various stope geometries including a drop raise blast at the start of the mass blast. The modeling concept is also described in the paper.

Jan 1, 2003

By Jack Curran

KANSAS CITY, MO - Performing one of the most impressive urban building-implosion projects in recent memory, Tulsa, Oklahoma-based Dykon Explosive Demolition Corp. and Omaha, Nebraska-based Anderson Excavating recently felled the landmark Columbia Bank Building in downtown Kansas City, Missouri, USA. Although every structural blasting project presents special challenges, this undertaking was most notable for its unusually unique structural design, tight clearances, and high risk to adjacent structures.

Jan 1, 2003

By Thierry Bernard

For many years now electronic initiation has brought the time parameter to the centre of blast designs forever. Although this parameter existed before the era of electronic detonators, Blasting engineers or blasters could not directly handle it; technology imposed it. Only discrete values were available. Today, the fact that we can choose any detonation time for an explosive charge questions the viability of most of the rules applied for blast design. Thus, the very famous charge per delay method, that enables a level of vibration to be forecast at a given distance (“Chapot’s law”), is no longer necessarily valid when using electronic initiation. Therefore, it must be approached in a totally different manner. The KUZ-RAM formula, that allows fragmentation to be forecast, is also subject to the same distortion. The aim of this article is to show how the calculation laws used for blast design are influenced by the time parameter (sequence) and how we can efficiently make the most of this, in particular for vibrations. Copyright ©

Jan 1, 2005

By O E. Jr Crenwelge

Frequency domain, single-charge vibration signatures are used to interpret the characteristics of explosive impulse excitation and ground vibration transmission. The effects of charge height, charge splitting, and different blasting agents are first discussed. Then the effects of rate of change with distance of overburden material properties and layer or surface geometries are illustrated.

Jan 1, 1988

By Robert B. Hopler

The history of the first twenty years of the high explosives industry in the United States begins as an illustration of the free enterprise system at its best and ends with the industry virtually taken over by a single company: a company which strongly opposed the new explosive material at the beginning of the period. In the world of the late Twentieth Century we could almost compare this history to the opposition of the mainframe computer manufacturers to the introduction of the personal computer, and their later entry into, and attempted dominance of, that market. With computers in the twentieth century the attempt to dominate the market has not been particularly successful: with dynamite in the nineteenth century it was.

Jan 1, 1994

By David Ziegler

Rough sketches, field notes, an on-site conference or a phone call may no longer suffice to establish your blast plan at a job site. More and more, general contractors, site supervisors, owner re p resentatives, or the owners themselves want to know details about proposed drill and blast operations at their site, in advance. We are seeing more contracts that re q u i re a blasting plan to be submitted in writing. The purpose of this session is to discuss items that you might want to include and address in a written blast plan, and some ideas about how to present them. This is not intended to be a complete list of items that could be included in a blast plan. Contracts may list specific items that need to be addressed. Only a few of the more common elements will be covered here. The bro a der purpose of this discussion is to get you thinking, about what you might want to include in your own “standard ” blast plan.

Jan 1, 2004

Blasthole deviation is a frequent, well documented and undesirable occurrence in mining operations. It is caused by the drill string mechanics, operating variables and the interaction between the drill bit and the rock mass characteristics. It is composed of three distinct components: collaring or marking error, alignment error and trajectory deviation. This study has focussed on the dependence of trajectory or natural deviation on the geological features of the rock mass being drilled.

Jan 1, 1996

By Roberto Folchi

"This article deals with the excavation of a tunnel below the town of Isola LIRI, nearFrosinone, in central Italy. The tunnel was driven into a conglomerate formation, of lacustrine_fluvial origins, consisting in carbonate clasts with a sandy_silty matrix and calcitic cement. ""Drilling andblasting"" had to be adopted in place of a tunnel boring machine which had showeduneconomical performances. Good advance speed rates were achieved notwithstanding thepresence of some above structures to safeguard. The nearest structure (an old votivechapel) was less than 10 meters (33 ft.) far from the tunnel crown; the nearest residentialstructure was at about 15 m (49 ft.)."

Jan 1, 1993

By Kai Nielsen

The paper presents the results of several industrial and laboratory blasting, crushing and grinding tests and experiments investigating how blasting can influence the subsequent crushing and grinding operations. The paper also describes how these results can be used in order to optimize the entire comminution process from solid ore to a semifinished or marketable product. Two cases are presented, one looking at the processing of fine grained taconite ore, and the other discussing the processing of raw milling product for cement burning.

Jan 1, 1998

By Ivan Carrasco, Benjamin Cebrian

Mining companies have traditionally organized their structure around a scheme easy to manage: Mining Department and Mill Department. In a challenging landscape for mining, with decreasing grades, increasing rock hardness and more expensive energy, this way to organize departments has resulted in internal disputes and often contradictory targets between both mine and mill. These compete for individual, separated budgets whose Key Performance Indexes often damage each other’s output. The results are increased total production costs and reduction of profits. Some companies have completed the first step in eliminating these inefficiencies by creating Fragmentation Engineers and Fragmentation Superintendents. With all the knowledge available on the overall fragmentation process and costs, in this document an overhaul of the traditional management structure is proposed. Is a step further Mine-to-mill and mine-to-leach programs. Since comminution is the most expensive step of the mineral exploitation, it should be taken as a whole, not divided into competing departments. Thus, mining departments should be re-grouped into: transportation, fragmentation and flotation.

Jan 1, 2014

By Randall S. Marks

Bonneville Dam, completed in 1938, included the smallest and busiest lock on the Columbia and Snake River Navigation System. To expedite barge traffic through this restriction, a new larger lock was designed and contracted by the U.S. Army Corp of Engineers.

Jan 1, 1997

By Peter Moser, Frank Chiapetta, Sacha Diaj, Florian Bauer

Good toe breakage and a flat working bench after blasting are important parameters to achieve a high productivity during material loading and reduce the necessity for secondary blasting. Good toe breakage requires a proper burden – side spacing design and a suitable sub-drilling. With unfavourable jointed rock mass conditions the use of horizontal bottom holes still can be found as common work practice even that this is associated to high risks.

Jan 1, 2009

By Xing Zhao, Michael A. Sutton, Vikrant Tiwari, Damien Bretall, Xiaomin Deng, William L. Fourney, Uli Leiste

The dynamic response of a thin aluminum plate subjected to both shallow and deeper buried blast loading was studied. Using a combination of high speed stereo-vision and three dimensional digital image correlation (3D-DIC), sequential stereo images acquired every 38.25µs during blast loading were analyzed to determine full-field deformations and plate motions (displacements, velocities and accelerations, effective surface strain and effective surface strain rate). Measurements indicate that the initial sheet deformation was highly localized for both shallow and deeper blast events, with extremely high velocity and acceleration values recorded during the earliest stages of impact loading. Full field strain and strain rate data indicate that well defined strain and strain rate “maxima” are created in the plate, with the potential of affecting the dynamic plate behavior as well as it local failure.

Jan 1, 2010

By Robert Benedetti

This paper describes various mitigation methods in order to reduce the maximum acceleration of the floorboard of hulled vehicles when explosive charges buried in water saturated sand were detonated beneath them. The effects on floorboard acceleration of adding a vehicle hull, several types of floorboard bracing, the use of foam to fill the gap between the floorboard and hull, and the use of foam to isolate the floorboard from the hull have been investigated. Small scale testing was conducted, which used bar magnet velocity gages to measure the velocity as a function of time of the center of the floorboard, directly over the charge, where the acceleration was expected to be greatest.

Jan 1, 2012

By Brian W. Stump

"Seismic waves from explosions can be used to characterize physical processes in and around the source. The quantification of absolute levels of ground motion is important for minimizing impact on nearby people and structures. We contrast work in characterizing seismic radiation from contained nuclear explosions with ground motions from multiple explosion quarry blasts. A physical basedunderstanding of the explosion source function allows prediction and extrapolation to new environments where experimental data may not exist."

Jan 1, 1990

By Serge V. Krasavin

The behavior of rocks subjected to dynamic loading conditions under explosion includes sufficient information about hydrodynamic variables such as pressure P, mass velocity U, internal energy E, specific volume V and density p as functions of time. Measurement of dynamic characteristics in compressed media with manganin wire sensors has become common in the past few years, but the experimental data for certain media, such as rock, do not provide an exhaustive description of rock's behavior in the near zone of an explosion, which is highly responsible for the transformation of energy of explosives.

Jan 1, 1992

By Rufus Flinchum

Two of the most critical concerns a blaster faces today are airblast and flyrock. Airblast, sometimes called noise or overpressure, can cause damage to neighboring structures, especially windows. It also is the cause for many vibration complaints. The human sense of hearing is often more acute to identifying source than the sense of touch. When a blast occurs, the airblast is what identifies the event. The vibration that may be felt is then associated with the airblast. Vibrations of greater magnitude, such as passing trucks or construction work on the house, go unnoticed because their sounds are familiar or expected. Flyrock is the number one killer and cause of damage. Elasting laws provide limits for these two concerns. Failure to comply may result in fines, closing of the operation, and even prison. Airblast and flyrock originate from two distinct areas, the open face and the bench surface. Each of these areas is addressed in the detailed proven procedures that follow, and if used by the blaster in conjunction with his own blasting knowledge, a sound blasting plan can be developed to minimize the occurrence of airblast and flyrock.

Jan 1, 1992

By Norman Disley, David B. Counter, Lionel Hebert

Misfires in underground and surface production blasts can be costly. Costs can arise from loss of resource, production interruptions, having to redrill or otherwise refire the blast (a hazardous process at best), due to added secondary blasting or breakage, and/or from increased LHD maintenance costs attributable to poor fragmentation.

Jan 1, 1996