Search Documents

By M. T. Styles, E. Condliffe, R. C. Leake, R. J. Chapman, D. J. Bland

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Quantitative point analysis and microchemical mapping identified 52 different types of mineral in inclusions, usually ranging in size from 5 to less than 1 micrometre, inherited from source bedrock. A combination of grain chemistry, heterogeneity and inclusions provides a grain signature reflecting the type and history of source mineralisation. Several grains from an alluvial site are needed, to allow for bedrock variation and the presence of inclusions in only 10-20% of grains. A total of 1 530 grains obtained from 30 localities in Scotland were of ten types, two of them minor variants. Two types in the Highlands may be related to centres of Caledonian igneous activity, but the most widespread is likely to have been of deep-seated origin and structurally controlled. Gold in the Ochil Hills is probably from a source associated with Devonian andesitic activity. In the Southern Uplands, grain types reflect two separate episodes of mesothermal lode gold mineralisation and relationships with Permian red beds/mafic volcanics and with Tertiary dykes

Jun 19, 1905

By W. R. Chambers

A wide variety of mining conditions exists within the South Midlands Area and across this range of conditions more than one half of the mines are highly susceptible to spontaneous combustion. Two thick seams in which the greatest risk exists are described and illustrated. The different heatings which take place are categorized by the locations at which they occur in the mines: additional special cases not easily categorized by location are discussed separately. The discussion for each category of heating follows the pattern of: (i) the reasons why it occurs; (ii) when it arises the means by which it is fought, and (iii) the preventive measures taken in an attempt to avoid its occurrence. Relatively new factors which may affect the incidence of heatings are highlighted and suggestions are made which may assist in reducing the number of incidents in the Area. A new method of continuous sampling, analysis and recording is described and mention made of an original method of interpreting carbon monoxide results with the aid of the computer. The first results from this work show that an early warning is given of an adverse change in trend several weeks earlier than with the present methods. Lastly, suggestions are made about the direction in which research might proceed to assist in reducing the special hazards created by several features inherent in the present methods of mining.

May 23, 1905

By Williams J. A.

"Changes proposed in 1969 to modernize legislation governing the exploitation of mineral deposits in the United Kingdom serve as the basis for a discussion of what is considered to be a desirable framework for future legislative proposals.Proposals with regard to prospecting and exploration, evaluation, and acquisition and exploitation are considered, as are suggestions relating, inter alia, to aerial surveys and land restoration.It is concluded that without legislation along the lines proposed there can be no significant revival of metal mining in Britain."

Dec 30, 1971

By G. G. Barbante

Anode slimes produced during copper electrorefining are a valuable source of silver, gold, selenium and tellurium. The conventional pyrometallurgical process for treating slimes involves preliminary leaching in sulphuric acid followed by smelting in a reverberatory furnace with fluxes, but it is slow and has many recycle streams. The chemistry of the phases and the reactions that occur in slimes smelting are poorly understood and and this prevents major improvements to the process. Laboratory-scale experiments were conducted using unleached slimes, with and without the addition of fluxes and under neutral, oxidising and reducing conditions. Results show that selenium is readily removed as gaseous selenium dioxide and that molten Cu-Ag-Se-O phases form when fluxes are added. Oxidation-refining of these phases by air injection and flux addition can result in the formation of silver suitable for further electrorefining

Aug 1, 1995

By D. M. A. Flight, P. M. Green, J. A. Plant, P. R. Simpson

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The British Geological Survey's regional geochemical database is used to identify the patterns associated with the various mineral deposit types and to examine the extent to which their distribution reflects the presence of long-lived metallogenic provinces in the crust. Image analysis provides new insights into the setting of the mineralisation, geochemical constraints on tectonic models of Caledonide evolution and evidence for terrane amalgamation and large-scale processes. There is evidence that much of the mineralisation reflects the presence of long-lived provinces with a distinctive geochemistry reflecting their origins as zones of crustal extension. In the case of the Middle-Upper Dalradiam sedex deposits, the relationship between geochemistry and tectonic setting is direct. In other cases, rocks deposited in extensional zones appear to have acted as reservoirs of ore-forming elements which were further concentrated during later events

Jun 19, 1905

By B. E. Burakov, S. D. Lupal, O. A. R. Thalhammer, B. Saini-Eidukat

Electric-pulse disintegration is a mineral separation technique that liberates all mineral grains from any igneous or metamorphic rock irrespective of its lithology or grain-size distribution. The normal mechanical crushing of whole-rock samples is replaced by the rending effect of an explosion, produced by applying an electric current from a high-voltage power source. A voltage greater than the 100 kV necessary for the electrical breakdown of rock samples is achieved by using capacitors charged in parallel, but discharged in series. The sample sits in a water bath and the rapid distribution of electric pulses leads to an explosion which occurs preferentially along grain boundaries of the sample. Individual, undamaged mineral grains can be recovered in their original shape and form regardless of grain size. Examples are given of the liberation and concentration of important accessory minerals from different rock types. The examples show the recovery of diamond from two types of non-kimberlitic host rock in Popigai and Kumdykol in Kazakhstan and platinum group minerals associated with chromitites from the Konjdor intrusion and sulphides from intrusions in the Kola Peninsula in Russia

Apr 1, 1995

By M. V. Swain, N. Bristow, R. D. Dukino

During mining, crushing and handling the size of iron ore lumps decreases. Key factors in determining the amount and size of fines that are produced are the mechanical properties of the ore. In a continuation of earlier work on the same ores the mechanical properties of three Australian iron ores from Yandi, Koolan and Mt. Whaleback were determined. In particular, fracture toughness was investigated in greater detail by examining its relationship to crack length using the compact tension test. The elastic modulus and strength of the ores were also determined in flexure and compression. The results were interpreted using Weibull statistics, enabling the ores to be ranked according to strength and elastic modulus. These results, together with data on the mechanical response of the ores to stress and observations concerning the effect of mineralogy on cracking, provide a coherent understanding of the mechanisms involved when the ores fracture

Jun 18, 1905

By R. J. Pine, J. S. Coggan

Distinct-element modelling has been used to study the mechanisms associated with observed deformation of the western face of the quarry. A complex failure mechanism involving distinct planar surfaces that was proposed for a slope failure in 1967 has been modelled and shown to be plausible. In addition, deep-seated flexural toppling may contribute to the slope instability. Modelling has confirmed the detrimental influence of a raised water-table on the stability of the slope and also indicates that the observed cyclic opening and closing of tension cracks may be attributed to seasonal rise and fall of the groundwater level

Apr 1, 1996

By O. R. Eckstrand, M. Asif, P. L. Schwann, A. J. Naldrett, R. J. F. Scoates

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. PGE-bearing sulphide mineralisation is contained in the lower 600 m of the Upper Central Layered Zone of the intrusion. There are four regimes with distinctive crystallisation characteristics. PGE content is low, both in bulk rock and in terms of metal in 100% sulphides, in the sulphide-rich cumulates but increases sharply in the sulphide-poor cumulates at the base of regime 1. Increases in regime 2 have no such clear relationship with incoming cumulus sulphides. PGE contents are low throughout regime 3, but regime 4 has sulphides with high PGE content, decreasing rapidly upwards, at the base of many of its cyclic units. The observations are interpreted as indicating that sulphide saturation occurred in the middle of a cyclic unit in regime 1, after which fractional segregation of sulphide caused a systematic decrease in PGE content. The resulting contrast between 40 000 ppb PGE in sulphides below the mineralised zone and less than 1 000 ppb above is of practical importance in exploration for such zones. In regime 2 the magma chamber was open to fresh influxes and PGE content was not so sensitive to sulphide saturation. In many regime 4 units influxes of new magma caused immediate sulphide saturation and PGE depletion, so that PGE-rich cumulates do not underlie PGE-bearing sulphide zones. Theoretical analysis indicates that regime 1-type behaviour is likely to characterise intrusions below the level at which plagioclase has entered as a cumulus phase and regime 4-type behaviour above

Apr 1, 1994

By H. L. Paterson, R. R. Keays, M. J. Donaldson, D. J. Boyack, M. F. Smith, J. J. Gresham

"Albite-rich sedimentary rocks that contain abundant Fe sulphides occur in the lower portion of the ultramafic sequence at Kambalda and their broadly antipathetic relationship to most of the nickel orebodies is well documented. These sediments generally contain less than 0.1% Ni, but nickeliferous equivalents with 0.3 to >6% Ni occur locally in close spatial association with more typical volcanic peridotite-associated massive, matrix and disseminated ores. Nickeliferous sediments have been mined at several locations at Kambalda but, collectively, they constitute less than 2% of the total Kambalda nickel reserve. The nickeliferous sediments occur both on the ultramafic-footwall basalt contact and within the lower part of the ultramafic sequence, and are usually less than 5 m thick. They are commonly finely laminated rocks with a cherty appearance, composed essentially of layers of albite+quartz±amphibole, alternating with pyrrhotite+pentlandite±pyrite layers. Some contain a minor amount of carbon. The sediments are only of ore grade (> 1% Ni) immediately adjacent to massive Fe-Ni-Cu sulphides, which are interpreted as normal magmatic ores on the basis of geochemistry and the presence of distinctive ferrochromites. The nickel content of the sediments decreases to background levels (<0.1%) within about 20 m of the massive sulphides. In most locations the massive sulphides clearly have been emplaced tectonically within or adjacent to the sediments, which are commonly highly deformed. Typical nickeliferous sediments contain about 1% Ni, 0.1% Cu, 0.1% Zn, 400 ppb Pd, <0.2 ppb Ir and 10-200 ppb Au. They have lower Ni/Cu (average 10), higher S/Ni (average 6) and higher S/Se (average 11 200) than associated massive sulphides (average 40, 4.8 and 7400, respectively). The Pd/Ir ratio of the nickeliferous sediments (typically > 1000) contrasts markedly with that of associated massive sulphides (average ca 16).The high Pd/Ir values are similar to those which have been reported for hydrothermal Fe-Ni sulphides and barren sulphidic sediments of probable volcanic exhalative origin. They preclude a direct magmatic origin for the sulphides in the nickeliferous sediments, though S/Se and S isotope data indicate a magmatic source for the sulphur. The restriction of nickeliferous sediments to within about 20 m of normal magmatic sulphides and the lack of a widespread Ni dispersion halo suggest local redistribution of originally magmatic Ni. This probably occurred by diffusion and hydrothermal mobilization during deformation and amphibolite-facies metamorphism. Although not totally ruled out, a volcanic exhalative origin for the Ni seems unlikely."

Jan 1, 1984

By V. A. Melezhik, P. K. Skufin, L. P. Nilsson

these factors into account. Theoretical and

Aug 1, 1994

By P. E. J. Pitfield, S. D. G. Campbell

The regional shear zone runs along or near the southern margin of the Chinhoyi greenstone belt. It hosts four of the seven mines in the southern part of the belt with recorded production above 100 kg Au, including the top two current producers. Displacement occurred in the late Archaean, producing a shear zone with a trend ranging from northeast at Golden Kopje to east at Muriel. The orebodies at the two mines formed synchronously with the shearing and show strong but contrasting structural controls on mineralisation. The Golden Kopje orebodies plunge to the southwest, parallel to the intersection of curved foliation with discrete shear planes and sub-perpendicular to local stretching lineations. The Muriel orebodies plunge steeply west but parallel to local stretching lineations. The greatest fluid flow during mineralisation of the shear zone was along either the intersection of fabrics (Golden Kopje) or the extension direction (Muriel). There is no unique relation between the orebodies and the extension or shear direction. Where earlier mining has not established the directions of the oreshoots it is essential to understand the possible structurally controlled geometries of orebodies before planning a drilling programme to evaluate their potential

Apr 1, 1996

By D. R. Wardrop, G. Walton

Paper presented at the UK minerals industry conference held in Leeds, UK, 3-5 April 1995. A description is given of the approach that has been taken to the design of the 550 000 000 t superquarry with a planned life of 60 years that is proposed for development. The quarry has been designed to replicate a corrie and a sea loch and will include excavated slopes more than 570 m high. The main geological and physical controls on the layout and the choice of development method are outlined. The operation phasing is presented and the geotechnical constraints on slope design and the feasibility of alternative quarry limits are discussed. Environmental considerations have been dominant in planning and the quarry has been specifically designed for closure

Jul 1, 1996

By R. H. T. Garnett

N.B. This paper provoked much (positive!) discussion in later issues, with responses from the author (and thanks also for the many private contributions he had received) - see under Garnett R.H.T. Expanded version of a paper originally presented at the Alluvial mining conference, London, 11-13 November 1991 and published in Alluvial mining, Barking: Elsevier Applied Science for IMM, 1991, p.115-156. The usual measure of performance in gold and tin dredging is the R/E factor. It compares actual production or recovered grade for a given period with that estimated from the original sampling. The factor is a multiple of four component factors, each ideally approaching 1.00. The factors are concerned with estimation, selection, excavation and treatment. The estimation factor reflects the errors involved in determining the grade and depth of single drill-holes or pits. An optimum selection factor is achieved by a higher drilling density. The excavation factor is affected by failure of the dredge to excavate the total volume contained within its course. The required dredge throughput rate influences not only the success in digging recovery but also the treatment factor. No two alluvial deposits are the same, but, in general, the greatest divergence from 1.00 is invariably demonstrated by the estimation factor. A major divergence in one of the other factors may also be the cause of the R/E factor being significantly different from 1.00. The component factors are examined in detail and historical trends in R/E factors are discussed

Sep 1, 1991

By T. Ogasawara, J. P. Barbosa, A. J. Monhemius, F. T. Da Silvia

A thermodynamic analysis of the sulphation of rare-earth phosphates and the water-leaching of rare-earth sulphates was used to guide experimental work on the sulphation and leaching of concentrates from Pitinga. It was concluded that the sulphuric acid digestion of xenotime is technically feasible and could be used industrially to produce yttrium and other rare-earth oxides. Yttrium extractions of more than 90% were obtained by digestion at 503 K for 4 h at an acid:concentrate ratio of 2:1 with particle size -0.053 mm. The apparent activation energy at temperatures less than 473 K, as determined from the Arrhenius plot, was 11.0 kJ/mol, indicating that the reaction is controlled by the diffusion of the reactants or products through the sulphate layer

Jun 19, 1905

By W. P. C. Duyvesteyn, B. J. Sabacky

Reprinted with revisions from Extractive metallurgy of copper, nickel and cobalt, volume I: Fundamental aspects. ed. Reddy R.G., Weizenbach R.N. Warrendale, Pennsylvania: The Minerals, Metals and Materials Society, 1993. Development work on the Escondida process, concluding with the successful operation of an integrated leach-SX-EW pilot plant and a pilot flotation plant for the upgrading of leach residues, demonstrated that all major process objectives could be achieved. Extraction of 40% of copper in concentrates containing monovalent copper was achieved with essentially no oxidation of sulphide sulphur. The Cu contents of leach residues from four different types of concentrate were successfully upgraded to the original feed grades, giving a product that has potential as a high-quality concentrate for the smelter market. A compact solvent extraction section effectively recovered the ammonia lixiviant for recycling to leaching and selectively transferred Cu into a conventional acid sulphate electrowinning system. High-quality "six-nines" copper cathode was produced on commercial-scale stainless steel blanks, demonstrating that the process will be able to compete effectively in the premium cathode market

Dec 1, 1995

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By P. H. Morris

The profile of a delta formed by fine-grained mineral processing wastes, disposed of as aqueous slurries by subaerial deposition from a pipeline, has a significant bearing on the volume that is available for waste and water storage in a given containment structure. Earlier field data and laboratory experiments suggested that mine waste delta profiles could be predicted with high levels of accuracy using data from small-scale laboratory deposition tests. The relationships between the profiles of full-size and laboratory-model deltas were analysed using the principles of kinematic similarity and a recent theory of delta formation based on engineering hydraulics. Measured profiles of full-size and model coal-mine tailings deltas are compared and the prediction of full-size profiles discussed. It is shown that the data-derived laboratory-model deltas are insufficient to allow accurate prediction of full-size delta profiles. Initial slope data or other, equivalent data for the full-size delta are also required

Apr 1, 1996

By D. Large, M. H. Davies, B. Driedrichs, U. Matzander

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A prototype high-resolution electromagnetic system, based on the theory of controlled-source magnetotellurics, was developed. The electrical source field is fed into the earth by dipoles at preselected frequencies and a multi-channel receiver measures five electric and three orthogonal magnetic fields. Suitable mapping algorithms and spatial filters are applied to the data and a new technique permits calibration during measurement. The system was field tested over a blind orebody, at 250-550 m depth, in the Aguas Tenidas area of the Iberian Pyrite Belt. Ten lines totalling 12 000 m of profile length were completed in seven days and the orebody was identified. Tests in the Irish Midlands suffered from strong electromagnetic interference of cultural origin

Jun 21, 1905

By V. A. Melezhik, A. H. Green, L. N. Grinenko

Finally, a theoretical model is constructed that takes

Aug 1, 1994