Search Documents

By C. J. Kirkland

25th Julius Wernher memorial lecture given at Tunnelling '91, sixth international tunnelling symposium held in London, 14-18 April 1991. The title gives the lecturer a chance to share some of the lessons he has learnt in a lifetime of tunnelling and particularly in the last six years of his involvement with the Channel Tunnel and the International Tunnelling Association. These included: the difficulties of split contracts but the problems arising with Eurotunnel over the need to create a single owner to whom the banks could lend; the peripatetic nature of tunnellers who built London's underground in the 1960s and returned to build the Channel Tunnel from Egypt, Singapore, Hong Kong and Australia; the increasing requirement for strategic planning resulting in tunnels between European countries and the need for engineers to deal with decision-makers; EU work on harmonising regulations so that there need no longer be, for example, arguments over which regulations should be followed for temporary electrical equipment in the section of the UK tunnel that is technically in France; the huge improvements in safety standards and attitudes; the enormous increase in the scale of undertakings and individual contracts, with an accompanying change in attitudes to logistics; technological advances to cater for the high performance now required of equipment; and the rising importance of environmental issues. The lecturer also briefly touches on the work of the International Tunnelling Association

Jun 13, 1905

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

By A. Z. Lang, D. A. Hall

After a brief description of the causes of spontaneous heating and of general preventative methods, a detailed account is given of occurrences of spontaneous heating in the Main Seam (locally known as the 5/4 Seam) at Westoe Colliery. This seam is about 12 feet thick consisting of hands of coal and shale, but only 4 feet 6 inches is worked because of the thickness os strata in water-bearing rocks and the worked section is selected on quality considerations. An advancing longwall face in this seam (2nd South) began to heat after working for six months and ultimately had to be abandoned. By adopting retreating methods and mining narrow panels it has been possible to extract this coal at an excellent rate of productivity. The system of goaf ventilation is important, because the use of a bleed road would have given rise to dangerous conditions in a goaf which of necessity would have contained fallen coal. Preparatory seals were prepared at selected sites so that, if necessary, a panel could be sealed off quickly; these seals are completed as soon as possible (within three weeks) of finishing a panel. A gas sampling system has been instituted which includes daily sampling on the face and in the goaf, and weekly sampling at the stoppings of all completed panels. The coal has now been extracted from this seam for three years without any further difficulties from spontaneous heating.

May 23, 1905

By S K. Das

An intensive investigation into modern roof support technology, including hy draulic and control systems, has been carried out against the perspective of global development and support behaviour on longwall faces across the Indian sub-continent. The wide ranging study examined various types and designs of modern supports used in seams of varying thickness and inclination where caving and stowing were practised. Consideration has been given to structural analysis, support resistance, the various forces acting over and on the powered supports and to support compatibility. The examination of the phy sical parameters has been allied to field experience and, together, have led to the formulation of standard designs for both the powered support structure and structural systems. A realistic mathematical model has been formulated for calculating the capacity of roof support requirements resulting from the actual behaviour of the immediate roof stratum. As a result of the work, it should be possible to readily select the most appropriate type of support sy stem for the conditions and longwall mining method that is to be employed.

Jan 4, 1997

By P Cochrane

Our ability to generate information and transport it about the planet on super highways of optical fibre is about to change the way in which we communicate, work and live. There is not a single aspect of our future that will go untouched by the communication and computing revolution that Is now upon us. The change we are about to witness will overshadow the impact of the printed word, industrial revolution and physical transport. The next major wave of information technology (TT) development will focus on the delivery of information and experience on demand, in the right form, at the right time, at the right price, to fixed or mobile terminals anywhere, over networks of optical fibre, radio, satellite and optical wireless. Bandwidth, distance and time will no longer be significant cost elements as service and access become dominant.

Jan 7, 1996

By M J. Thomson, P T. Burgin

The economic growth of Hong Kong and adjacent territories in Southern China is, to a considerable extent, dependant on air transportation, but the present Kai Tak Airport is incapable of expansion to meet future needs. After years of study, agreement was reached to build a new airport on the island of Chek Lap Kok, some 34 km remote from Hong Kong, with an ultimate capacity of 87M passengers and 8.9 Ml of cargo per annum. Apart from the building of the airport and its associated infrastructure (including a new town), other similar massive construction works have been necessary in the form of land reclamation from the sea and existing outer lying islands. The construction of bridges, tunnels, railways and highways are also an integral part of the project. The paper provides a broad overview of the concepts of the scheme (called The Airport Core Programme) and highlights some of the major operations and equipment being used in the projects, whose cost at 1992 prices was reckoned to he Hong Kong (HR)$l63hn.

Jan 7, 1997

By Jones R. G.

Dr Pat Foster, Senior Lecturer in Mining Engineering at the UK's Camborne School of Mines, talks to Rhiannon Garth Jones about mining safety around the world, education and the future of the industry

Feb 1, 2015

By O. Dojcar

Equations for calculating the parameters of controlled blasting (burden and spacing of boreholes and weight of the bottom charge) are derived and analysed on the basis of empirical values and made more precise through incorporation of the properties of the rock being blasted and explosive applied. For the success of controlled blasting the correct choice of the blasthole diameter/charge diameter ratio is critical. This relation is defined as the coefficient of radial decoupling of the charge; it is recommended that it is chosen to be between 3 and 3.5. Analysis of smooth blasting, cushion blasting and presplitting indicates that cushion blasting is a less destructive alternative to smooth blasting, but it has a slightly higher blasthole consumption and limited possibilities of use. There are definite economic advantages to controlled blasting, especially in rock masses of low and medium strength

Dec 1, 1996

By C R. Ferrari

Residual subsidence is generally accepted as being about 5% of the total subsidence occurring within 12 months of all mining finishing. This paper looks at five case studies from different parts of the country, in various mining settings within a depth range of 430m to 760m. From a single seam single panel working to working the eleventh seam, all are within the concealed coalfield, similar to today's mining. The monitoring of subsidence continued for many years once the mining had finished and the results obtained are at considerable variance from the accepted norm. Subsidence has been found to carry on for up to eleven years after mining has ended, within a range of 8% to 45% of total subsidence. A highly significant factor was that subsidence, as a whole, was generally much more than predicted. The residual subsidence aspect has to he viewed in this context and in order to debate the subject at length, the causes of residual subsidence have to be balanced against the apparent inability to accurately predict subsidence. The results from the case studies were similar, even though the mining settings differed considerably. Subsidence of around 10% to 20% continued for several years after mining had ceased.

Jan 7, 1997

By M. Riddell

This paper describes the incipient heatings that occurred below ground in the High Main and Main seams at the mine between the years 1963 and 1966. The possible causes, effects and activities associated with such heatings are discussed in an attempt to establish the precautions necessary to minimize such occurrences. The assessment of as many "norms" as possible is made to enable the earliest detection and level of activity to be determined.

May 23, 1905

By Fearnsides W. G.

Discussion at the The Midland Institute of Mining, Civil and Mechanical Engineers' general meeting held in Doncaster on 27th May 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.409-448, included oral contributions by Lupton A. on the mechanisms of subsidence and water egress and by Kendall P.F. on the validity and accuracy of the contour extrapolation technique and the effect of major faults, together with the author's response

Dec 1, 1916

By J. K. Brimacombe, F. D. Richardson

Studies have been made of interfacial turbulence occurring in reactions in which indium, zinc and cadmium, dissolved in amalgams, are oxidised into aqueous phases by ferric or mercurous ions. It has been found that this turbulence occurs when the concentrations of oxidising ions in the aqueous phase become sufficiently great. These concentrations are the same as those at which the mass-transfer coefficients in the aqueous phase increase sharply when both phases are stirred by gas bubbles rising through them. The effects of gas flow rate on the mass-transfer coefficients for zinc in mercury have been established, and the oxidation of pure mercury has been investigated. The relevance of the work to processes involving liquid metals is discussed

Dec 1, 1971

By A. C. Dunham, Y. D. Drakapoulos, P. W. Scott

The Pt and Pd occur alloyed with copper in small, irregularly-shaped grains, 0.25-5.0 micrometers in maximum dimensions. Grains of unalloyed native copper are also present. The grains are completely surrounded by or marginal to magnetite with inclusions of Ni-Fe-Co sulphides and native Ni-Fe, which is apparently a product of the serpentinisation process. Crystallisation of the Pt-Pd-enriched copper probably occurred at the same time, at low temperature, but the previous form of the Pt and Pd is unknown as no earlier PGE phases have been found. While Pt and Pd minerals are usually important in early-magmatic base-metal sulphides, Pt alloyed with Cu is extremely rare and apparently occurs only very late in the paragenetic sequence. A Cu alloy with Pd dominant over Pt and only minor amounts of other elements appears not to have been reported

Jun 14, 1905

By D. G. Skinner, M. SC. Griffiths

"The natural difficulties associated with the size evaluation of dusts render absolute measurement difficult, or indeed, impossible. Assuming that the desirability of gravi­ metric sampling be conceded, it appears likely tha,t the most suitable means available for physical evaluation are the method of total turbidity measurement, to give a con­ ventional value for specific surface, together with microscopical examination, the great merit of the latter being that in the hands of an experienced operator, semi-quantitative discrimination between coal and other particles is possible.The pipette method, as modified by Fryer, probably-deserves more attention than it has received up to the present. Whatever method is used, it is recommended that in view of the lack of medical knowledge, as much information as possible should be obtained with reference to the total mass concentration, the surface area of the total dust,' and the mass and area of the particles below 5μ in size."

Jan 1, 1947

By Tuncel M. Yegulalp, Selamet G. Ergelebi

A description is given of a method of analysing modern mining systems in terms of reliability and their effects on productivity. Non-exponential distributions, such as the Weibull and lognormal distributions, for failure and equipment repair times are also considered. The resulting non-homogeneous Markov process is solved by the method of stages. A longwall mining system is analysed as an example.

Jan 4, 1993

By J. Temporal

An introduction to the conference material in this issue is given together with the issue contents list, closing remarks by its chairman Dr. J. Temporal, the list of contributors and their companies, and the information that the 26th Sir Julius Wernher memorial lecture had had to be presented by the lecturer's wife, M. Biggart, in his absence due to site problems on the Storebaelt project

Jun 16, 1905

By Schwartz M.

Respect for mining in Botswana is long-standing. This article looks at Africa's most transparent mining regime and some of its ambitious plans. Botswana's mining industry value is forecast to average 5.2% growth from 2014-2018 with solid growth for the diamond sector and acceleration of coal production. Respect for the country's mining regime is maintained in the Fraser Institute 2014 annual survey where Botswana occupies the 26th position of 122 administrations. Botswana's transparency is illustrated by Mupane gold mine near Francistown, Ghaghoo diamond mine in the Gope area and the Morupule coal mine

Mar 1, 2015

By D. D. Lei, H. Sevim

Long-term production planning in open-pit mines requires the determination of cut-off grade, mining and milling production rates, a mining sequence, mine life and ultimate pit limits. Since these variables interact in a circular fashion, a genuine solution to the problem necessitates their simultaneous determination. A methodology with this capability is described. This comprises a group of heuristic algorithms and an unconventional dynamic programming algorithm. The method is demonstrated using data for a gold deposit in the western USA

Jul 1, 1996

By T Atkinson, A Cobb, R AJIington

Risk management is concerned with the whole spectrum of financial, geological, engineering, legal, governmental, social and occasionally ethnic issues, concerned with mining projects. The inherent risks in mining operations are well publicised, but new issues and hazards arrive on the scene and lake precedence, but the older risks still remain, while insurance cover may not he ‘full cover’ in the future. It has long been recognised that quantitative approaches to risk analysis can play a major role, but although these methods are capable of considerable theoretical precision, the lack of sound risk input data and experienced personnel limits the usefulness of theoretical analysis. It can, however, greatly assist in comparing cases, in identifying areas of risk and help in the investment decision process. Its major contribution to a mining project is that it imposes an investigative discipline that also assists in improving the quantitative approach to risk analysis and hence risk management. Risk analysis and risk management also requires sound common sense and major inputs from experienced geologists, mining, mechanical, electrical and mineral processing engineers. The Engineering Council, in 1992, issued a ten point code of professional practice entitled ‘Engineers and Risk Issues’ (The Engineering Council. 1992), covering our professional responsibilities, the law, our conduct, the need for a systematic approach to risk issues, the use of professional judgement, communications, risk management, evaluation of risk, our professional development in this field and the encouragement of public awareness of risk issues. This is a specific area of training perhaps long neglected by our industry and academic institutions (Atkinson. 1983).

Jan 5, 1996

By D. J. Allan, W. R. Wilson

For conventional aerospace aluminium alloys of the 2000 (copper) and 7000 (zinc, magnesium) series the recycling of process scrap from both metal suppliers and aircraft manufacturers is a well-established, worldwide industry. The recent introduction of a new family of alloys that incorporates lithium has posed a new challenge to the recycling industry owing to the high cost of lithium, its high reactivity to the atmosphere and to refractories and its absence from the specifications of all other registered alloys. Various process options for recycling have been identified, but vacuum distillation has been selected as the most cost-effective and technically feasible solution. Experimental work established that the separation of Li from AI-Li scrap is feasible and an industrial process has been designed. The economics of Li recovery are very sensitive to the AI-Li content of the feed material. Owing to the design of aerospace vehicle manufacturing plants it is expected that the swarf will be mixed with other alloys. A method of enriching this feed has been developed that is based on the control of swarf morphology by thermal and mechanical treatments as a precursor to eddy-current separation. After eddy-current separation and vacuum distillation small proportions of Li are retained in the AI residue. The effects of this on the properties of conventional AI-Si shape-casting alloys were investigated and safe threshold levels have been established.

Jan 4, 1993