Search Documents

By S. F. Kaplan, A. S. Dolotov, V. N. Kovalev

"The proportion of refractory sulphide ores and concentrates in world gold mining industry is growing every year. Pressure oxidation of these materials (in autoclave) allows to oxidize gold hosting minerals. Traces of halides and pseudohalides present in the slurry liquids contribute to formation of complex gold compounds. Sorption-active carbon present in ores leads to irreversible adsorption of complex gold compounds and their loss. The objective of the research is to study gold extraction dependence on the concentration of chloride-, cyanide- and thiocyanate-ions in the slurry liquids during pressure oxidation. Double refractory flotation concentrate of the Bakyrchik deposit was used for the testwork. The research was planned on the basis of a full factorial experimental design with additional refining experiments. Ligand concentrations (0 – 1000 mg/l Cl-, 0 – 600 mg/l CN-, 0 – 1200 mg/l of SCN-), temperature (200 – 240 °?) and retention time (1 – 6 h) were used as variables of pressure oxidation process. It was determined that sulfide minerals oxidize much faster than ""organic"" carbon. Under the conditions of T = 240 ?C, t = 2 h, sulphide sulfur oxidation was 95.6%, while ""organic"" carbon oxidation was 46.1 %. Each of the examined ligands has a significant adverse impact on gold extraction. Analysis of the experimental data demonstrated that with a high degree of confidence (R2 = 0.883) gold extraction does not depend on the ligand type, but only on its concentration and the ""organic"" carbon oxidation degree. In case of complete oxidation of ""organic"" carbon, the presence of the ligand (L = Cl-, CNS-, CN-) in the liquids at a concentration of up to 20 millimole/L does not significantly affect gold extraction. The assumption that the main factor of preg-robbing in ???-CIL treatment of double refractory concentrates is the natural ""organic"" carbon sorption-active to gold has been confirmed. INTRODUCTION In recent decades, placer gold mining has been gradually declining and hardrock gold mining, including ""refractory"" gold mining, has been growing all over the world, as well as in the Russian Federation (http://www.miningworld.ru, 2015). One of the main reasons why gold ores are refractory is gold adsorption on natural carbonaceous materials (""organic carbon""). Only a few technologies are suitable for processing such ore concentrates (a significant amount of gold is contained in refractory hardrock ore both in Russia and worldwide) (Vorob'yev-Desyatovskiy N.V., Yepifanov A.V., 2014)."

Jan 1, 2018

By I. N. Gridasov, V. V. Khromov, R. I. Ismagilov

"Over 50 mln.tonne is the average annual output of oxidized ferruginous quartzites typically containing Fe38-42% mined in Mikhailovskoye ore field. The most promising and cost-effective way to expand concentrate production maintaining current output of magnetite is processing of oxidized ferruginous quartzites (hereinafter referred to as OFQ) mined as a by-product in Mikhailovsky open pit mine. However lack of proven and efficient concentration and agglomeration process applicable to OFQ and insufficient data for feasibility evaluation of OFQ processing encumbered full-scale addressing of this challenge. Based on outcomes of multiple various studies a process of OFQ flotation was designed by MC Metalloinvest LLC and PJSC Mikhailovsky GOK engineers. Comparative lab-scale testwork have proven performance and production advantages of flotation against magnetic separation feat. flotation and combined concentration method. Lab-scale flotation enabled production of concentrate with average Fe66.6% and SiO22.06% grade. Geologic and production contouring of OFQ deposited in Mikhailovskoye ore field has been carried out to collect necessary data for feasibility study incl. cost and profit estimation. As a result processing and production properties of over 3,500 samples have been analyzed which is characteristic of every direction and level of prospective ore mining within Mikhailovskoye ore field up to year 2032. Following work has been done based on geologic and production contouring of OFQ: – natural typification of ores and production (processing) grades of OFQ, determination of average mineral composition; – correlation analysis of interrelation between OFQ mineral composition and processing features thereof for overall bulk of samples as well as for individual data blocks related to various directions of open pit mine; – OFQ classification with account of defined mineral composition and processing features. Total Fe weight content in chamber product of flotation (known as concentrating ability in flotation) was applied as a major differentiating factor for processing grade classification of OFQ. Three processing grades of oxidized ferruginous quartzites were established as a result of flotation tests run to determine concentrating ability, i.e. – hard concentrated OFQ (TO) – below Fe65%; – mean concentrated OFQ (SO) – Fe65-67%; – easy concentrated OFQ (LO) – over Fe67%. Outcome of this work provided initial data for feasibility study and cost-profit evaluation of medium-term industrial-scale processing of OFQ deposited in Mikhailovskoye ore field."

Jan 1, 2018

By A. Gülmez

The complex ore deposit containing fluorite, barite and bastnaesite minerals is located in Beylikova Region of Sivrihisar town of Eskisehir Province of Turkey. The ore contains 40.80% CaF2; 35.35% BaSO4; 2.01%Ce; 1.5% La; 0.39% Nd and 0.1% Th. Barite recovery from this ore by flotation of the HCl leached tailings is presented in this paper. Rare earths are recovered by leaching. The leached residue (tailings) containing fluorite and barite is subjected to froth flotation to recover barite. The effect of pH and collector concentration on the flotation of barite have been studied in this work.

Sep 1, 2012

By E. V. Zelinskaya

"Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production. Considerable attention in recent decades has been given to waste recycling. The task is to maximize the use of both newly formed and accumulated solid and liquid wastes. The mining and mining and smelting enterprises industrial waters are a very promising source of secondary hydromineralic raw materials. They have high concentrations of not only calcium, sodium, but also, for example, lithium, rubidium, heavy non-ferrous metals. In general, unfortunately, we have to state that today there is no wide practice of extracting valuable components from waste enrichment, as well as processing of man-made waters to extract metals from them. The quantity of extracted components from underground, and furthermore passing waters, is insignificant. At the same time there is a tendency to increased demand for rare metals: Sr, B, Br, I. This is explained by their wide use in many industries. For example, the consumption of lithium products is steadily increasing. The obtained results showed that in the liquid phase in connection with high salt content and a significant difference in the macro- and microcomponents contents, conditions are initially created for the microcomponents selective isolation possibility. The identified conditions realization is most possible in such technological processes as cryotechnology, sorption and ion flotation. There is an urgent need to expand research in this direction and to recognize as a publicly important task the mining and industrial waste processing full-scale introduction into the practice of operating mining and processing enterprises and iron and steel companies.INTRODUCTION Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production."

Jan 1, 2018

By Sushanta Majumder

The physico-chemical characteristics of raw materials used for the production of iron ore pellets have a strong influence on the productivity of pelletization operations and on the quality of pellets. Since iron ores from different sources are used for making iron ore pellets and since the quality of the ores varies with time, there is a need to optimize and control pellet plant operations on a regular basis to achieve optimum productivity while maintaining pellet quality within the desirable specifications. In order to achieve this objective, a model-based on-line optimization system was implemented on two industrial scale induration furnaces. The optimization system consists of a rigorous mathematical model of the induration process, a model for the permeability of the bed of pellets, a statistical model for the quality of iron ore pellets and an optimization module based on sequential quadratic programming. The rigorous model is tested on-line using the wind-box temperature available real-time. The process was optimized to enhance induration furnace productivity for the given constraints on pellet quality parameters such as the cold compressive strength (CCS) and Tumble Index (TI), and other equipment design parameters. Process variables such as induration machine speed, cold air flow rate and hood temperature profile were used as the optimization variables. The on-line optimization system was successfully implemented in two industrial induration furnaces and lead to enhanced productivity. Details of the on-line optimization system and results of process optimization will be presented.

Sep 1, 2012

By D. W. Lui

Tangdan copper oxide deposit, the largest independent copper oxide deposit in China so far, is located in the northeast of Yunnan province, southwest of China. The ore from this deposit is characterized by: low grade, high oxidation ratio, and fine-grained disseminated, resulting in poor flotation recovery. The analysis of plant flotation data reveals that the loss of copper minerals into tailings is mainly with coarse size fraction due to insufficient liberation and fine size fractions, especially minus 10 microns fraction, which proved to be very difficult-to-float with conventional flotation. In order to improve the performances of plant flotation of this ore, laboratory flotation tests were conducted with the pure malachite, which was the principle copper oxide mineral in Tangdan copper ore deposit. The results obtained suggested that a finer grinding (up to -325 mesh or even -400 mesh) be needed to decrease the loss with coarse size fraction, and vacuum flotation is a promising way for the recovery of the fine malachite effectively.

Jan 1, 2014

By M. C. Harris

"In the flotation process the contact angle is an important indicator of the hydrophobicity of a mineral particle. There is considerable literature showing that the contact angle increases when the chain length of the alkyl group associated with the collector molecule used to render the valuable mineral particle hydrophobic increases. The extent to which an alkyl group interacts with surrounding water molecules is quantified thermodynamically by the excess Gibbs energy. In the present paper it is shown that there exists generally a strong linear relationship between the excess Gibbs energy of the alkyl group associated with the collector and the contact angle. The structure-activity of such alkyl groups is in turn related to the total surface area, molecular volume, the molar volume, molecular weight of the functional groups in the molecule and interaction energies. It is proposed that the demonstrated relationship is indicative of the role which the alkyl group component of the collector, which is attached to the mineral particle, plays in increasing the extent to which water molecules at the surface of the mineral are rejected from the surface thus increasing the contact angle. The relationship between excess Gibbs energy and surface tension is further explored with a view to relating the observations quantitatively to the parameters in the Young equation.INTRODUCTIONThe issue of wettability of materials is of great importance to many industrial applications. Wettability studies usually involve the measurement of contact angles which indicate the degree of wetting when a solid and liquid interact. As is well known the contact angle (O) is the angle between planes tangent to the surfaces of the solid and the liquid at the wetting perimeter which is the zone where the air, water and solid phase merge. When the air bubble attaches to the solid surface there is an increase in the air/solid interface area and a decrease in the solid/water interface area. For attachment to occur the cosine of the contact angle should be less than 1 and this will be promoted if the interfacial surface tension between the air and the solid (? SV) is low. Classically the relationship between these parameters has been expressed through the Young equation (1) for a perfectly flat surface:"

Jan 1, 2018

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"The effects of mixed collectors on some physicochemical parameters (thin film lifetime, kinetics of expansion of the three-phase contact, equilibrium three-phase contact angle and surface tension) involved in the elementary act of flotation were investigated experimentally.We have used the microscopic thin balance developed by Scheludko et al (1970) to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates at 1:1 molar ratio. The experiments were performed at a range of concentrations at pH 6.5. The equilibrium contact angle was measured with a microscope technique using the modified Mingins-Sheludko method (Mingins and Scheludko, 1979). The surface tension was measured by the method of Wilhelmy (Adamson, 1960). It was found that the mixed surfactants caused lower contact angles, lower rates of the thin film rupture and longer film lifetime, compared to the pure amine system."

Jan 1, 2003

By Qingming Feng, Dongbo An, Jinhong Zhang

The application of the geopolymerization of mine tailings as construction materials is hindered by the fact that conventional geopolymerization of mine tailings usually involves a large consumption of alkali, i.e., sodium hydroxide (NaOH), and a long curing time, because of the relatively low reactivity and the high Si/Al ratio of mine tailings when compared to other active resources such as fly ash and clay minerals. The present study is focused on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. We firstly investigate the temperature effect on the alkali activation of mine tailings during geopolymerization. Secondly, the impact of additives, i.e., calcium hydroxide and aluminium oxide, on the compressive strength of samples is studied. Thirdly, different forming pressures have been applied to remove excessive alkali and its impact on samples' strength has been investigated. The results show that a 40 MPa unconfined compressive strength (UCS) can be achieved with the geopolymerization samples after mine tailings are activated by sodium hydroxide at 170°C for 1 hour with the addition of calcium hydroxide and alkali dissolved aluminium oxide, further compressed with a 10 MPa forming pressure and finally cured at 90°C for 3 days. The findings of the present work provide a novel method for the geopolymerization of mine tailings as construction materials.

Jan 1, 2014

By Güven Önal, Gülay Bulut, Mustafa Özer, Yunus Emre Benkli, Olgaç Kangal, Mustafa Tarkan

There are various types of natural zeolite deposits in Turkey. Naturally occurring zeolites are excluded from many important commercial applications where uniformity and purity are essential. In this paper, the beneficiation of natural zeolite, taken from western part of Turkey, was investigated. According to X-Ray Diffraction (XRD) and mineralogical studies carried out on the representative ore sample, the natural zeolite was found to be in the forms of clinoptilolite and heulandite. Clinoptilolite forms as a devitrification product of volcanic glass in tuffs. Quartz, clay minerals, orthoclase, plagioclase, biotite, seruzite-muskovite and epidote were observed as impurities. Several types of mineral processing methods were performed in order to remove impurities from the natural zeolite sample to produce high purity zeolite. Gravity separation methods such as shaking table and superpanner were carried out for separating heavy minerals, while high intensity dry magnetic separation was used for discarding magnetic minerals.

Jan 1, 2003

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By Ray Everson, Henry Kasaini

"We carried out adsorption experiments in chloride media to study the adsorption characteristics of Pd (II) anions on the surface of activated carbon. Throughout the experiments, we used commercial activated carbon pellets (0.8 Norit). The adsorption process was interpreted by using the ionisation and adsorption model. This implies that palladium anions were adsorbed physically on a protonated surface of activated carbon either as anionic complex species (PdCl4 -2) or aqua chloro-complex species [PdCl3(H2O)-] in acidic media. Furthermore, we established that adsorption of Pd (II) species was reversible at high chloride [Cl-1] concentration. The maximum adsorption capacity (Qsat) of Pd (II) anions averaged 27 mg/g. The Toth adsorption isotherms fairly predicted the equilibrium adsorption of Pd (II) species and the associated surface coverage.The effect of temperature and acid strength of the feed solution on the adsorption of Pd (II) ions were quantified. The adsorption kinetics was limited by external mass transfer since the effect of pore diffusion on the overall rate constant was negligibly small. A pseudo first-order kinetics model was used to describe the adsorption kinetics."

Jan 1, 2003

By Y. Posedko Eugene, S. S. Gudkov, Yu. E. Emelyanov, A. V. Bogorodsky, A. V. Boldyrev, S. V. Balikov

"The article presents the results of precious metals leaching using halogen solvents and their precipitation on a sorbent in the process of pressure oxidation. A technology of pressure oxidation – carbon-in-leach treatment (POX-CIL) of refractory sulphide gold-bearing flotation concentrates with the addition of a halogen solvent and a sorbent was developed based on the laboratory studies and pilot plant tests. The technology involves the following steps: oxidation of a flotation concentrate; precious metals dissolution and recovery on a sorbent; precious metals elution; electrolysis of eluates; smelting of cathode precipitates with producing Dore beads. This approach ensures oxidation at least 98% of sulphides and gold of more than 95%. The POX-CIL process have the following patents: a patent of the Eurasian Patent Organization No.017438 “A method of processing materials containing precious metals and sulphides” and a patent of the Russian Federation No.2625146 “A method of precious metals recovery from refractory sulphide gold-bearing materials”.INTRODUCTION Gold-bearing ores are classified as readily amenable to cyanidation, or non-refractory, and not readily amenable to cyanidation, or refractory [1]. Special attention should be given to the three most common technological types of gold-bearing ore materials, according to the Irgiredmet’s classification: pyrite-arsenopyrite ores with finely disseminated gold locked in sulphides (physical depression of gold in cyanidation process); cupriferous gold-bearing ores, when cyanidation comes along with chemical depression of gold by mineral compounds (cyanisides); carbonaceous ores showing higher sorption activity to precious metals dissolved in cyanide. Direct cyanidation of refractory sulphide gold-bearing materials does not provide high recovery of precious metals. There are the following methods of refractory gold-bearing ores and concentrates preparation to subsequent gold recovery: roasting, fine grinding, bacterial and pressure oxidation (POX) [2]. Existing POX-cyanidation flowsheets involve high costs due to a large amount of process operations and using expensive and environmentally hazardous sodium cyanide."

Jan 1, 2018

By William Conger, Greg Schick

Grinding media consumption is a major cost variable in industrial mineral comminution circuits. Specifically, industrial SAG media consumption results from a combination of surface abrasion wear, media breakage, surface spalling and rejection size from the mill. Three main consumption rates; weight of media consumed per time, per kWh and per weight of ore ground are defined and compared. Recent industrial data has provided an opportunity to relate consumption in terms of weight of media consumed to weight of ore ground (g/tonne) and weight of media consumed per kWh of energy consumed (g/kWh) with SAG specific grinding energy consumed (kWh/tonne). Using relationships developed from this data it is possible to project SAG media consumption in future mineral comminution circuits.

Jan 1, 2014

By A. Kamali Moaveni, A. Boehm

"The current research study addresses a physical separation process of basic oxygen furnace slag “BOF-Slag” (also called Linz-Donawitz “LD” slag) for the removal of phosphorous. In order to recycle the LD-Slag into the steelmaking process, the physical dephosphorization methods are considered. The systematic geometallurgical investigation carried out on particle classes of decreasing size, which were further subdivided into susceptibility classes, shows intimate intergrowth beyond 40 µm due to slag´s fast cooling rate. Generally, LD-slag is constituted of oxide and silicate phases, among which di-calcium silicate “C2S” dominates. About 0.5 mass% of phosphorous was detected in the LD- slag, which is exclusively situated in the lattice of the C2S. The comparatively high grinding resistance (Rittinger index 12.9 cm²/J) of the LD-slag reflects the energy demand to liberate the phosphorous carrying phase from the iron containing minerals, while separation efficiency decreases in the very fine particle size range. Hence, the conversion of the phase intergrowth pattern was considered alternatively to re-build the mineral phase structure of the material to a separable interlock pattern. Carbon dioxide, as the most convenient substance in the steelmaking plants, was applied to digest the C2S in the presence of water and to reduce the basicity of the slag slurry. As a result of C2S-CO2 chemical reaction, calcite and calcium silicate are precipitated at the surface of the oxide particles and carried between 25% and 75% of the total phosphorous, respectively. Accordingly, the mobility of the phosphorous content phase to the top of the grains serves the possibility to separate the precipitated layer by mechanical attrition process. This paper is focused on the impact of the intergrowth pattern alteration on the slag´s separability characteristics. Moreover, the operating conditions of the carbonization process, such as temperature and pressure, on the deconstruction kinetics of the C2S and the generated products will be considered. INTRODUCTION The steelmaking BOF-Slag is a stony aggregate waste from the steel manufacturing process. The investigated slag by the current research work was provided by voestalpine steelmaking plant in Linz, Austria. The current legislative situation in Austria restricts the historical application of slag as construction material, due to the high level of heavy metals content and corresponded land-filling and transportation costs of slag, therefore the demand for recycling of BOF-Slag to the steelmaking process has raised, as an alternative application. Statistically, voestalpine steelmaking plant produces about 130 kg BOF-Slag per ton of final steel product, which serves annual BOF-Slag production of 700,000 ton, approximately."

Jan 1, 2018

By M. Brozek

The particle settling velocity is the argument of separation in such processes as classification and enrichment in jigs. It characterizes material forwarded to the separation process and belongs to the so-called complex arguments because it is the function of particle density and size. i.e. the function of two simple arguments. The affiliation to a given subset is determined by the values of two mag-nitudes and the distribution of such argument in a sample is the function of distributions of particle density and size. The paper will present a method of determining the distribution of settling velocity in the sample of spherical particles for the turbulent particle motion in which the settling velocity is expressed by the Newton formula. Because it depends on density and size of particle which are random variable of certain distributions, the settling velocity is a random variable. Applying theorems of probability, concerning distributions of function of random variables, the authors will present general formula of probability density function of settling velocity for the turbulent motion and particularly calculate probability density function for Weibull?s forms of frequency functions of particle size and density. Distribution of settling velocity will calculate numerically and perform in graphical form.

Jan 1, 2014

By T. X. Hu

Pyrite ore is one of the main raw materials in the production of sulfuric acid. For a long time, the raw material containing the pyrite, which is used to produce sulfuric acid, generally contains S only 32%~45%. A plenty of residue from the sulfuric acid production contains 40%~50% Fe and 1%~2% S. Some of the residue also contains Cu, Pb, Zn and other harmful elements like As, thus it pollutes environment seriously and is solid waste. The research on comprehensive utilization of the residue has been made by many scholars. Through the study, the residue can only be used to pro-duce iron concentrate and the iron oxide red pigment. But because of the complex techniques, the low recovery, the low grade of iron concentrate , high sulfur in iron concentrate, causing second waste residue and the environmental pollution, the residue is mainly used as an accessory material in the production of cement, and is of a low value. Therefore, the iron resource in pyrite has not been used efficiently until now. In the paper, the flotation condition test, the flotation open circuit test and the flotation closed circuit test to produce high-purity pyrite concentrate with the low-grade pyrite ore in oceanic ore deposit have been carried on. Flotation reagent scheme of sulfuric acid used as activator and butyl xanthate as collector is determined. After four times depth cleaning, high-purity pyrite concentrate containing 52.82% S, 44.29% Fe, and only 2.89% impurities has been obtained. The S recovery is 99.13%, and the Fe recovery is 96.00% in the high-purity pyrite concentrate. The oxidizing roasting depth desulfurization experiment of the high-purity pyrite concentrate has been conducted. The results show that the Fe grade in the residue obtained is 68.58%, the content of S is 0.25%, the content of P is 0.0084%, the content of As is 0.0065%. The residue is a kind of high-quality iron-smelting raw material. Based on the above experiments, the industrial experiments on producing high-purity pyrite concentrate with the low-grade pyrite ore, and producing sulfuric acid and iron concentrate with high-purity pyrite concentrate have been done. The results indicate that the high-purity pyrite concentrate with the S grade of 51.24%, the Fe grade of 44.15% has been obtained. The iron concentrate obtained with 65.73% Fe and 0.23% S is a sort of high-quality iron-smelting raw material applied to the production of steel and iron smelting. Through the experimental study, the sulfur and iron resources in the pyrite ore have been recovered and utilized efficiently.

Jan 1, 2014

In this paper, various methods, such as XPS, XRD, SEM and zeta potential measurement are applied to investigate the action mechanism of sodium sulfide in flotation of lead and zinc oxysalt minerals. The experimental results show that the mechanisms of sodium sulfide in flotation of lead oxysalt minerals and zinc oxysalt minerals are different: on the surface of cerusite, there is lead sulfide phase formed under the reaction of sodium sulfide, resulting that the cerusite surface shows the form of galena, which is advantageous to the adsorption of anion collector and improves the floatability of cerusite as a result. On the surface of zinc oxysalt minerals, there is no zinc sulfide phase formed, but the sodium sulfide increases its surface electronegativity, and enhances the adsorption of cation collector lauryl amine, so the floatability of zinc oxysalt minerals is improved. The difference of action mechanisms of sodium sulfide on lead and zinc oxysalt minerals exactly explains the reason why different collectors are selected in the flotation of cerusite and smithsonite, which are both carbonate minerals although.

Jan 1, 2014

By Teemu Väyrynen, Matti Vilkko, Antti Jaatinen, Pekka Itävuo

"This paper shows that smooth and accurate feed-hopper level control is essential for consistent cone crusher operation. The objective of the paper is to define the best practices for tight control of cone crusher feed-hopper level. The paper discusses the challenges involved in a delay-dominant level control problem (specifically, dead-time-induced performance and stability issues, mass flow disturbances, process and actuator non-linearity) and proposes five corresponding control structures. The performance of the proposed control structure candidates is evaluated in a simulation study and, finally, a full-scale experiment is conducted for the best-performing candidate. The results of this study emphasize the importance of control structure selection. While the most obvious control structures failed to deliver the desired performance, the best result was achieved by using control structures that eliminate the conveyor transport delay (dead-time) from the control loop. In practice, the control loop dead-time can be eliminated by either using an actuator (variable-speed feed conveyor) that is connected directly to the feed-hopper, or by redefining the process boundaries closer to the used actuator (regulate the circuit mass balance instead of feed-hopper level). The presented control structures provide means to achieve a consistent cone crusher performance and size reduction. This facilitates efforts to improve the plant’s performance and increases the plant’s overall stability."

Jan 1, 2014

By Victor Avdokhin, Ivan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation.Catching coat is formed of natural magnetic and weak-magnetic placer minerals in field of magnetic system of the sluice. Magnetic minerals, placing along magnetic lines of force, form rough coat of fluffy structure. Size of the magnetic particles is chosen taking into account expected size of gold particles, which are to be fixed on the rough coat or between the magnetic particles. Changing coarseness of particles of mineral bed allows to regulate selectivity of recovering heavy minerals.Forming artificial fleece from magnetic minerals of initial sand, increasing capacity of the bed and relative hydraulic proportionality of mineral particles of the bed provide for the most effective recovery of fine gold."

Jan 1, 2003