Search Documents

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

By Silas C. Nichols

"Abstract Piling and deep foundations are a staple for transportation projects in the United States (US). Driven or bored piles have been used for everything from support of bridge foundations and retaining structures to support of culverts and embankments on soft ground. Deep foundations have been popular in the US transportation market to better handle large axial and lateral loads, extreme event loading, and to better control structure movement. However, there are challenges in the maintenance of design and construction codes in transportation for consistent and reliable structure foundation elements. A significant amount of effort continues in the US to maintain national codes and specifications at a level consistent with the state of practice, and identify and conduct research for providing safe and cost effective highway structures.IntroductionThe transportation sector in the United States has a hierarchy of design and construction codes that are used for the specification of piling and deep foundations. Any highway or bridge project on the National Highway System (NHS) must be designed and constructed in accordance with a national set of standards approved by the State Highway Departments, and that are acceptable to the Federal Highway Administration (FHWA). However, in any jurisdiction, exceptions are permitted with approval. Therefore, design may be governed by the national standard specification, a state standard specification and design manuals, special provisions, or guideline specifications. Any of these standards, or a combination, may be used depending on the needs of the owner agency.The FHWA and the American Association of Highway and Transportation Officials (AASHTO) have worked together in the development and maintenance of geotechnical design and construction guidance and codes that support the surface transportation community. General geotechnical engineering practice in the United States lacks a singular, national design and construction code that addresses all aspects of geotechnical engineering. As a result, the AASHTO specifications provide the most complete geotechnical specifications focusing on structure foundations, retaining walls, and buried structures for surface transportation applications. This includes piling and deep foundation types commonly used for support of bridges and transportation structures.The FHWA National Geotechnical Team has published several technical guidance documents that include guideline specifications for the design and construction of driven and bored deep foundations. Reference documents published by FHWA summarize the state of practice and provide recommended design and construction guidance. These reference documents have long served as a basis for provisions included in the AASHTO specifications. Maintenance of the design code and specification, and related guidance documents for consistent use on US transportation projects requires a collaborative effort between industry, FHWA, and the member state highway departments that make up AASHTO."

Jan 1, 2014

By Eric C. Halpin

"1. Introduction and Backgrounda. In its fundamental form, risk is simply the likelihood of an adverse impact. Expanding on this theme, the Corps of Engineers has broadly defined risk associated with infrastructure as a factor of three distinct elements: a probabilistic assessment of a hazard such as a flood or earthquake; a probabilistic assessment of how the infrastructure performs in the face of this hazard; and a measure of the likely consequences – loss of life, economic damage, environmental impacts – associated with the resulting inundation scenarios.b. The lessons and observations described herein relate to the Corps of Engineers experiences in implementing risk concepts for infrastructure management during the period 2005 through 2013. The Corps of Engineers is a large, decentrally operated and centrally led federal agency that plans, designs, constructs, operates, maintains, and/or manages a portfolio of over 3,000 built dam and levee systems within the United States. The infrastructure in this portfolio is 55 years old on average, and although much of the structures provide for flood risk management benefits, many of the dams deliver multi-purpose benefits. Scale matters – where scale and uncertainty are large, risk concepts provide great opportunity and arrangement for application.c. The amount of organizational change that is demanded for the implementation of risk concepts is considerable and should not be under estimated, but need not be feared if the path others have taken is considered. This paper is, in many ways, an opportunity to step back from the last seven years of implementing risk informed management, check our own azimuth and maturation, and share the purpose and energy behind our own continuing actions. Hopefully, this azimuth check is also beneficial to those that are either considering the use of risk or are in the process of implementing risk concepts.d. Success at managing the massive change related to incorporation of risk concepts will directly affect success of the infrastructure program. The three key organizational elements to consider –human systems such as governance and competencies; policies that outline the who, when, and why of decisions and management; and the processes and technology that outline how work is to be performed - are changed fundamentally. From senior leaders to project team members and all of the people in between, there is a need to discuss, confront, and vet the change and the role people and organizations have in the process. For the Corps of Engineers, with a history of over two centuries, deeply embedded beliefs about infrastructure aren’t transformed over night - the change process is decadal in scope. Given our self imposed “project execution” mantra and corporate objective, risk seemed threatening at first to the cost and schedule of delivering infrastructure projects. In reality, risk concepts have been responsible for savings and cost avoidance of nearly $6 billion over the last three years alone while at the same time justifying increased investment by several fold for the highest risk needs."

Jan 1, 2014

By Monica Prezzi

"Auger cast-in-place (ACIP} piles and drilled displacement piles are being increasingly used as foundation elements for structures, particularly in projects requiring accelerated construction or involving the rehabilitation of foundations of existing, overstressed structures. Auger cast-in-place piles (also referred to as continuous-flight-auger piles) are widely used to construct the foundations of all types of structures. There are many different types of drilled displacement piles, with the installation methods varying according to the equipment used. Depending on the specific rotary piling technology used, responses ranging from those associated with non-displacement to those associated with full-displacement piles are obtained. Conventional pile design methods do not account for how the various construction techniques involved in auger piling change the soil state around the pile during installation and, hence, cannot accurately estimate the pile resistance in a consistent way. Research on this subject, identifying the different variables that must be accounted for in design and linking these variables to installation methods, is lacking. This paper describes the different piling methods available for auger cast-in-place and drilled displacement piles, the equipment used to install them and the quality control processes typically used. It also reviews some of the design methods currently used.IntroductionDeep foundations are extensively used in geotechnical engineering practice. The wide spectrum of piling methods results in a variety of pile types. Each type behaves differently, depending on the installation or construction methods. On one end of the spectrum are non-displacement piles, the classicql examples of which are bored piles or drilled · shafts. These piles are constructed by removing a cylinder of soil from the ground and replacing it with concrete and reinforcement. On the other end are full-displacement piles, such as closed-ended pipe piles or precast reinforced concrete piles, which are typically driven into the ground. Driven piles preload the materials below the toe of the pile and displace the soil surrounding the pile shaft laterally during the installation process. Therefore, displacement piles are, in general, more likely to have a stiffer response than non-displacement piles. This is true particularly in the case of sandy soils where displacement causes densification."

Jan 1, 2005

By George J. Tamaro

The design and construction of foundations in the New York City area are usually dictated by the widely varying geologic conditions encountered in the five boroughs, particularly along the spine of Manhattan Island. Rock extends well above sea level at the northern reaches and falls to depths in excess of 250 m at the barrier islands at the southern extremities. These highly variable geologic conditions, significantly affected by glacial activity, dictate different design and construction approaches throughout the five boroughs of New York City. Extensive rock removal is required at the north while long piling is dictated in the south. Similar changes can occur within a project site on Manhattan Island. This paper will describe these conditions in general, will identify the various solutions used to solve these problems and will summarize various foundation types used in the New York City area.

Jan 1, 2000

By Thomas Billups, Brendan FitzPatrick, Doug LeDo, David Carchedi

"Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. This paper describes the use of the modular Ductile Iron Pile system, a low-vibration driven micropile, on two urban projects on the Johnson & Wales University campus in Providence, Rhode Island. The paper describes the successful implementation of Ductile Iron Piles installed to develop capacity in end-bearing on one site and friction on the second site. Design, installation and quality control operations are all presented as well as the results of full-scale load testing performed on non-production test piles. This paper is of importance to the industry because it describes a versatile option for project teams as an alternative to traditional micropiles, helical piles or other deep foundation systems for urban sites.INTRODUCTIONWorking in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. Two recent projects in downtown Providence, Rhode Island faced a combination of problematic soil conditions and urban construction challenges including vibration concerns. Both projects were a part of the Johnson and Wales University campus development. Figure 1 illustrates the urban locations of the sites."

Jan 1, 2016

By Michael Hughes, Selva Selvamohan, Ray Costa

"Cutoff walls are commonly used to mitigate underseepage problems for levee remediation projects. At abrupt changes in seepage cutoff wall depths there is a potential for water to flow around the back of the deeper cutoff wall leading to elevated seepage pressures on the landside that could result in exit gradients exceeding design criteria. This condition is referred to as end-around-effects and is a complex problem that requires detailed and time consuming 3-D numerical modeling to represent accurately. This paper presents a simple approach for assessing end-around-effects using the results of 2- D seepage analysis to determine if lateral extension of the deeper portion of the cutoff wall is required. This simplified approach provides a pragmatic solution to a complex 3-D problem. The presented procedure was used as part of the Feather River West Levee Project in Yuba City, California, to assess end-around-effects at 26 locations. The results showed that wall extensions of up to 100 feet were needed at only 2 locations.INTRODUCTIONAs the lead geotechnical consultant for the Feather River West Levee Project, AECOM were responsible for designing levee remediation works for approximately 35 miles of levee protecting the area around Yuba City, California, and communities to the north and south. Due to land use constraints, seepage cutoff walls were the main remediation alternative selected to address underseepage issues for the project.As part of the design review process, the California Department of Water Resources (DWR) requested AECOM to look at 26 locations along the levee alignment where the depth of cutoff wall changed abruptly from shallow to deep, or vice versa. At these locations there was the potential for seepage pressures to pass behind the deeper section of cutoff wall and stress the blanket layer landward of the cutoff wall. A condition referred to as end-around-effects.End-around-effects involve complex 3-D ground conditions that have traditionally been addressed by laterally extending the deeper section of cutoff wall an arbitrary distance based solely on engineering judgment. In discussions with DWR, AECOM developed a simple procedure to provide a more objective assessment of end-around-effects without the need for detailed and time consuming analysis. This procedure allows the engineer to make an informed decision of whether end-around-effects are a problem at the location of a cutoff wall transition rather than laterally extending the deeper section of cutoff wall an arbitrary distance based on engineering judgment alone."

Jan 1, 2015

By David H. Sanders, Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Large-diameter drilled shafts (DS) are a critical part of a seismic-resistant system, and therefore it is important to be able to accurately model lateral resistance. To undertake the lateral load analysis of largediameter DS, a finite-difference p-y analysis program, NVShaft, is being developed at the University of Nevada Reno. Validation of the new program involved numerous p-y analyses using commercially available programs. Subsequent comparisons suggested the program's ability to yield reasonable predictions for typical diameter DS. Based on the I-15/US 95 load test program carried out in Las Vegas, NV, this study presents the evaluation of NVShaft in Nevada’s subsurface condition. Lateral load analyses of a 2 ft and an 8 ft diameter DS were attempted using NVShaft. The location of the applied lateral loads and the presence of cemented soil-layers were incorporated in the modeling. A good agreement between NVShaft prediction and the measured response was found for the 2 ft diameter DS. For the 8 ft diameter DS, a stiffer response was predicted. The inspections of the moment-curvature characteristics at different load levels suggested cracked response of the concrete due to prior axial load testing may be one of the reasons behind the deviation.

By F Debidin

The progressive rise of an H-pile during driving of an adjacent pile is described in this case history in which piles 15 to 18 m long were driven to end-bearing for the foundations for a 230 m long building. The use of a reaction beam-soil anchor system for compression load tests is discussed. The results of static load tests to determine pile capacity are compared with those obtained by the Pile Driving Analyzer and by theory. Unusual high temporary compressions were observed by field control staff. Proof testing was necessary to determine the need for restriking of some piles in which rise had occurred.

Jan 1, 2010

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997

By J. L. Goen

The Saint Joseph Hospital of Bellingham is located on a site underlain by glacial outwash. The construction of a five-story tower addition above an existing two-story wing was supported by five large trusses that impose a 1600 kips (7117 kN) column load on five pile caps in the courtyard of the hospital and on the new pile caps inside the existing MRI laboratory. The exterior columns of the trusses and the new parking garage addition were supported on conventional auger cast piles installed with conventional equipment. Helical Pulldown® micropiles were selected for use in the courtyard and the MRI laboratory because lightweight installation equipment (maximum unit weight of 7.5 kips (33.3 kN)) had to be used and it was required that no spoils be produced. The installation equipment was lifted into the courtyard by the jobsite crane. Sixty Helical Pulldown micropiles were installed for the pile caps in the courtyard. The pile caps inside the hospital were supported on 240 Helical Pulldown micropiles. Initial compression test indicated an allowable load for the micropiles to be 55 kips (244 kN). However, retest at a later date resulted in an increased allowed design load to be 85 kips (378kN) reducing the number of micropiles required by more than fifteen percent.

Jan 1, 2004

By Stefano Trevisani

Abstract The FIEC Sustainability Vision states that “risks should be identified and allocated in a fair manner across the project team from the early stages of the design phase. A partnering approach, where objectives and timescales are agreed in advance together with all relevant partners in the value chain, offers a useful solution to improve on site efficiency and reduce disputes”. An alliance or collaborative form of contract involving all parties is the best way to ensure fair contract conditions and proper risk allocation in construction projects. Collaborative contracts are particularly useful where there is uncertainty or undefined information or in the event of technical difficulties and other risks difficult to allocate among the parties involved in the project. Owners sometimes require even special output in terms of innovative technical solutions or special performance. In addition, this particular form of cooperation has been construed and developed with the intention of avoiding and mitigating another great risk associated with the construction industry (especially in complex projects): disputes and conflicts, which are often a major cause of delays, increased costs, loss of reputation and opportunities. In contrast, Alliances are a way to increase and strengthen business relationships, technical and economic innovation and effectiveness, in a worldwide global context where the waste of resources must be avoided in order to guarantee future recovery and growth. Of course, the total cost of a project is usually a key factor and the main driver for the Owner and the Contractors in deciding the type of relationship between them as well as the subsequent relationship with subcontractors and lower-tiers. This paper and presentation, will explain the main features and the principle benefits that the use of collaborative contracts can bring to all parties involved in the construction project, including the sustainable financial return that might be achieved if costly and time consuming disputes can be avoided.

Jan 1, 2014

By Partha Sircar

"For Berth 22 modifications at the Port of Oakland, nearly 600 octagonal 24-inch ‘diameter’ precast-prestressed concrete piles were driven, some piles over 160 feet long. Prior to production pile driving, an indicator/test pile program was performed, which included extensive use of dynamic load testing with (Pile Driving Analyzer (PDA) & CAPWAP analyses. The indicator test-pile program resulted in requiring significantly longer piles than the original design based on subsurface borings. The cause of this discrepancy is investigated in light of the available geotechnical information, soil mechanics principles and standard techniques for pile capacity computations. Several interesting phenomena emerged. These include relatively low resistances offered by crushed rockfill than would conventionally be assumed, non-homogeneity of an apparently uniform formation and the effects of jetting on pile side friction. Also revealing was the significant increase in capacity between 1 and 3 weeks of driving for long piles in clay. Recommendations were developed for pile capacity for future use as “lessons learned”.IntroductionThe foundation for the replaced Berth 22 structure at the Port of Oakland in California involved driving approximately 570, 24-inch octagonal precast prestressed concrete piles. A plan and a section for the pile locations are presented in Figure 1.The ultimate loads on the piles used in the design are presented in Table 1 – the loads are quite heavy.The foundation design was followed by an extensive Indicator Pile Program. The contractors (Manson Construction Co. of Richmond, California) opted to use a Delmag D62-02 diesel hammer (Rated Maximum Energy – 165 kip-feet). Per the project specifications, the same hammer was used for both indicator and production pile driving. The production piles of appropriate lengths were ordered based on thr results of the Indicator Pile Program. A number of interesting results were found from the Indicator Program, which is discussed in this paper."

Jan 1, 2015

By R. J. Yan

There was a plant equipped with a 32000t Hydraulic Press to be built, under which a box foundation of 22.5m x 15m x 14.25m (depth) with a base slab of, varying thickness was proposed. The subgrade reactions, bending moments and settlements needed to be determined by means of in-situ model test. A model of the same materials as the prototype scaled to l/10 was embedded in-situ with simulated depth in the bedrock. A lot of data obtained from 39 bench marks, 32 elongation measuring points, 30 couples of electric resistance strain gauges and 24 pressure cells attached to the model foundation enables all the quantities required to be found out. Since it was put into operation, the settlements measured has reasonably agreed with the test results and the foundation has been in good condition.

Jan 1, 2010

By Waddah Akili

The demand on pile installation in the offshore of the Arabian Gulf has, over the last two decades, experienced unprecedented boom, triggered by the construction of platforms, to help facilitate the production and transport of oil and gas. Available borehole data show that ground conditions for pile installation in the offshore is highly variable, resulting in misassessment of insitu conditions, leading to a huge discrepancy between ultimate pile capacities, based on design, and actual capacities after installation. The paper makes use of pile installation records derived from several platforms in the offshore of the state of Qatar, the Gulf Region. More specifically, the paper evaluates “as–installed” ultimate capacities and safety factors, recommends remedial installation procedures, and proposes a means for determining pile acceptability for piles meeting refusal short of design penetration. The paper offers what is believed to be relevant recommendations to guide the design and installation of future offshore structures; enabling the geotechnical community in the Region to solve their current offshore pile installation problems and gain an added margin of confidence regarding the ultimate capacity of installed piles.

By Rob Jameson

Micropiles are ideally suited to seismic retrofit applications. Their high tensile and compressive capacity can sustain the large concentrated loads induced during seismic events. Micropiles can be drilled through and grouted into the wide variety of soil and rock materials encountered in seismically active zones, using equipment that operates effectively within existing structures. Micropiles have seen increased acceptance and are now widely specified for retrofit work in the San Francisco Bay Area. While installation equipment and the structural configuration of micropiles have been largely unchanged since the early 1990?s, market forces have pressured both engineers and contractors to continually optimize the cost and performance of seismic upgrades. Instead of the contractor simply developing stronger, stiffer and cheaper micropiles as isolated structural elements in response to a specification, focus has shifted to maximizing the efficiency of micropiles within the overall foundation system. The case history of seismic retrofit project in Berkeley, CA is presented to illustrate the collaboration between designers and drilling specialist which resulted in a structurally efficient and cost effective design. The seismic retrofit program for this 6-story concrete building was developed through careful consideration of the geotechnical and structural mechanisms of resistance, in combination with the deformation response of high capacity micropiles (2670 kN) under ultimate loading conditions. This case history describes the interactive project development emphasizing performance-based design and field testing to optimize the micropile foundations and the overall structural system.

Jan 1, 2008

By Pete Howell, Patrick Granitzki, Alicia Plinio, Janitha Batagoda

The New York City Housing Authority (NYCHA) Red Hook Houses was subjected to damage during Superstorm Sandy. As a result, the NYCHA has an ongoing project known as Restoration Associated with Sandy Recovery Program to improve the resistance against future storms. The specific project included 28 residential buildings and several service buildings within the Red Hook Development. The subsurface conditions within the eastern portion of the site included existing fill material underlain by varying stratums of very loose, loose and medium dense silty sands followed by very soft to medium stiff clay or dense silty sands. The western portion of the site included existing fill material, very loose to medium dense silty sands and organic clayey silts underlain by very soft to medium stiff sandy silts. Based on the geotechnical report, a conventional driven steel pile system was specified containing two pile depths. As part of the project bidding, an alternative pile type was recommended and analyzed to provide quicker installation, reduce vibrations, reduce noise, and provide relatively large cost savings. Due to relatively high lateral loading, an innovative double steel casing drilled displacement piles was proposed as the alternative pile option. Field testing proved the piles capable of the required project capacities and the use of drilled displacement piles as the best alternative for the project and accepted by the NYCHA.

Oct 1, 2022

By Sanjeev Malhotra

"This paper presents the results of a pile installation monitoring and performance assessment program for pile foundations supporting 14 piers and 2 abutments of the 1700-ft long bridge crossing over a river in Baltimore, Maryland. Dynamic measurements were conducted during installation and restrike of 16 test piles, one at each support location. The foundation piles were 30-inch diameter, 0.75 inch thick pipe piles at the piers and 24-inch diameter, 0.5 inch thick at the abutments. The piles at the piers were approximately 100 ft long and were designed to carry 260 kips service load with a factor of safety of 2.25. The piles were driven open ended into a variable site stratigraphy containing recent deposits of organic clayey silts near the mudline followed by loose to medium dense sand, with some silt, and then by soil deposits from the Cretaceous period consisting primarily of dense to very dense, poorly to well graded sands and gravels and cobbles, with occasional seams of very hard to very stiff, low to moderate plasticity silts and clays. This paper presents the approach taken to evaluate the driven index piles and to develop criteria for driving production piles. It provides the Engineer with some data on pile driveability in Cretaceous soils in the Baltimore area, soil set-up effect, and an estimate of pile capacity.INTRODUCTIONThe typical approach to pile foundation design and construction should include an indicator pile program with dynamic measurements and a static load test program. However very often paucity of funds and schedule constraints cause an owner to do away with conventional static load testing which can take $25,000 to $100,000 and several weeks per test. This paper examines an alternate (though not equivalent) truncated approach to foundation assessment and presents a case history where this approach was implemented.Dynamic measurements were conducted during pile installation for the 14 piers and 2 abutments of the new 1700-ft long bridge over a river in Baltimore, Maryland. Strain transducers and accelerometers were attached to the pile top during initial driving and restrike of 16 pipe piles. The foundation piles consisted of 30-inch outside diameter, 0.75-inch thick pipe piles at the piers and 24-inch outside diameter, 0.5 inch thick at the abutments. The piles were driven open ended into a variable site stratigraphy. The approach taken to assess the foundation performance included 1) a pre-field wave equation driveability analyses, 2) field pile driving measurements, 3) post-field Case Pile Wave Equation Analyses (CAPWAP), and, 4) revised wave equation analyses based on field and CAPWAP data. The following sections describe in greater detail each of the steps taken to assess foundation performance and the results obtained."

Jan 1, 2005

By Mary C. Nodine, Michael P. Walker, Paul Eggers, Donald E. Aubrecht

The CANALSIDE commercial development in Buffalo, New York serves to revitalize the former site of the Buffalo Memorial Auditorium, adjacent to Lake Erie. The Auditorium was constructed in 1940 and founded on steel H-piles driven to limestone bedrock. After decades of professional sport and entertainment events, the “Aud,” as it was locally known, was closed in 1996. It sat vacant until it was demolished in 2009, at which time plans were made to revitalize the area with shops, restaurants, and a historic replica canal. The only portion of the Aud that was left intact was a subbasement boiler room. The subbasement was renovated in 2014 and has since been used to house water and ice making equipment for the historic replica canals, which boast recreational ice skating in the winter. The subbasement floor was about 10 feet below groundwater and the Lake Erie water level. The floor consisted of an approximately 4-foot-thick layered inverted waffle slab system, with reinforced concrete grade beams and concrete infill between the grade beams. A waterproofing membrane was located near the base of the slab. There were no major seepage issues in the subbasement, so the existing waterproofing membrane was assumed to be intact and performing adequately. A four-story building housing a children’s museum was proposed to be constructed directly above the subbasement. The loads imparted by the new building would exceed the capacity of the existing piles, so it was determined that drilling micropiles through the subbasement floor would be the most practical means of supporting the new building. Drilling through the existing slab and waterproofing system was a concern due to the challenges of controlling water during construction and the importance of maintaining the integrity of the permanent waterproofing system.

Jan 1, 2018

By Ken MacLeod

A development at 83 Queens Road in Melbourne, Australia required construction of a three level basement. The normal geotechnical constraints of excavating adjacent to an existing relatively new building were challenging enough for the complicated soils profile occurring at the site. An additional significant challenge faced by the designers, was the requirement to excavate underneath the entire footprint of an existing heritage listed building, known locally as the Mansion, in the centre of the site. Maintaining the structural integrity of that building was afforded the highest priority during the 10m excavation. This paper describes geotechnical aspects of the analysis, design and construction of the secant retention system adjacent the new building and support of the Mansion enabling the 10m excavation to proceed without causing damage to the structure. The secant wall comprised hard-soft interlocking piles constructed using CFA methods. CFA piles along the length of the Mansion provided short term support, with the building load being transferred to the piles by large steel beams jacked under the building. Survey results confirmed that movements of the retaining wall and also the load bearing piles were minimal and well within design expectations.

Jan 1, 2006