Search Documents

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010

By M. Tarvainen, J. Kallioinen

"Depressed metal prices coupled with increasing production costs have presented a great challenge for operators to control and reduce the costs of production to maintain profitability. Depleting ore reserves, added to the above has forced Outokumpu to take a hard look at its operations, to develop new methods to profitably extend the life of its mines. One of the areas investigated and approved for further development has been the use of larger and more energy efficient equipment. As a result, large flotation machines were developed and today 38 and 60m3 flotation machines are in use.Secondly, ore preconcentration has been developed to avoid processing the part of the ore that has little or no mineral values.Another quite recent development and the topic of this paper, has been the use of coarse flotation before conventional flotation. The main idea is that part of the valuable mineral is separated as early as practical by floating it with specially designed flotation equipment, installed in the grinding classification circuit. The new flotation cell is specially designed for this application and differs from the conventional cells in the tank design, feed arrangement and modified mechanisms in some cases."

Jan 1, 1984

By C. M. Davidson, D. J. Drexler

"Sulphuric acid treated with hydrogen peroxide to destroy organic contaminants could conceivably show increased corrosivity toward carbon steel shipping and storage vessels, caused by the persistence of a peroxide residual. This paper describes work performed to determine the effect of 0-200ppm hydrogen peroxide on the corrosion of carbon steel by 93% and 98% sulphuric acid at room temperature (23ºC) and 50ºC.Steel electrodes were exposed to acid containing several peroxide levels (0. 45, iOO and 200 ppm) for up to two weeks. Specimens were removed at intervals and weight loss, open circuit potential, depth of metal loss and residual peroxide concentration recorded.Hydrogen peroxide decomposes considerably over two weeks in iron-contaminated sulphuric acid. initial peroxide concentrations > l00 ppm suppress corrosion, but the effect is lost when concentration decays below about 60 ppm. Sustained peroxide levels in the range below 60 ppm may increase corrosion rates. These phenomena are interpreted by analogy with anodic passivation."

Jan 1, 1987

By V. K. Gupta

"Effect of mill speed on grinding kinetics has been investigated with a view to using mill speed as a manipulated variable for control and optimization of the grinding circuit performance under variable ore hardness conditions. Dry and wet batch grinding tests were carried out for quartz, limestone and cement clinker in a 29 cm x 18 cm laboratory ball mill. Mill speed values selected were 55 and 70% critical. In the case of dry grinding operation, with an exception of quartz, for all materials studied the effect of mill speed on grinding rate was found to be insignificant for sizes finer than about 35 mesh. In the case of wet operation, grinding rates were found to be approximately proportional to the mill speed. The implications of these results are discussed.INTRODUCTIONIt is well known that mill speed has a considerable effect on the grinding rate of the ore particles l-3 For particles of a given size there is an optimum speed at which mill grinding efficiency is maximum (i.e. specific energy consumption is minimum) 3•4. Mill speed can, therefore, be effectively used as a manipulated variable to deal with the disturbances arising from changes in the size and hardness (grinding rate) of the ore being fed to the grinding circuit. Though, it has not been the case so far, with recent developments of ring motors2 and frequency inverters5 a continuous variation of mill speed has now become feasible, and it is expected that mill speed control will soon be a regular feature of plant operation2,6."

Jan 1, 1985

Why A Friction Hoist? B EFORE discussing the equipment, it would be instructive to review the factors that influenced the management of Opemiska Cop-per Mines to purchase a friction hoist rather than a conventional double drum hoist. The mine required that 250 tons per hour be hoisted from a depth of 2,100 feet. They also specified that the top speed should not exceed 1800 feet per minute. Eight ton capacity skips in balance and a maxi-mum hoisting speed of 1725 feet per minute would meet the required <Output on a duty cycle as follows: Loading time Creep away from loading pocket Accelerate (at 2.5 ft/sec2) 10 seconds 5 seconds 11.5 seconds Full speed run Decelerate (at 2.5 ft/sec2) Creep into dump Cycle time Trips per hour Tons per hour 72 seconds 11.5 seconds 5 seconds 115 seconds 31 31x8 = 248

Jan 1, 1962

By H. W. Wevers

Fatigue failure and accompanying brittle failure occurs frequently in heavy mining equipment. This paper discusses how fracture mechanics can be applied as a tool for crack control and crack management. Information is provided to determine if particular components are prone to brittle failure. By using existing fracture mechanics formulae, an estimation of the critical crack size can then be made. It is explained that for a successful application of fracture mechanics, both the actual engineering stress in the component and the mechanical properties of the applied material must be known. The importance of toughness at low temperatures is quantitatively illustrated by calculating critical crack sizes at room temperature and at below-zero temperatures. Understanding the possibilities of fracture mechanics will also produce a climate in which the purchaser of equipment can more precisely analyze the relative quality of components with respect to crack tolerance and failure prevention. In this manner, communication between the user and manufacturer of equipment may also become more precise and effective, leading to improved design.

Jan 1, 1977

By Zolfan F. Oszter

As exploration for new mineral deposits advances farther into the Canadian North, the more the design engineer is faced with the problems of cold weather conditions. This is especially true when designing belt conveyor systems for open-pit operations where the temperature in the winter may go to -40°F or below. Problems with the mechanical components and also with the belting will arise, which in turn may reduce the availability of the system. This paper outlines the problems encountered during cold weather operation and what precautionary measures must be taken into consideration in the design of equipment, as well as in the selection of materials, in order to ensure a system which will maintain production. THE conveying of ore and waste in the pit or to the processing plant poses problems during cold weather, when temperatures may drop to -4o?F or be-low. Troubles with the mechanical components, the belting or the supporting structure may arise, and this, in turn, will reduce the availability of the conveying system.

Jan 1, 1965

By Samantha Beeson, Collin Poole

"This paper examines the development of two new selective flocculation techniques for recovering KCI values from low grade carnallite potash ore.Direct recovery of KCI was achieved using one of two mid-range molecular weight polymers, one non-ionic and the other strongly cationic, in conjunction with the same selective anionic dispersant. From initial response studies on pure minerals and selective flocculation tests on synthetic mixtures, investigations were extended to recover KCI values from a natural carnallite potash ore. A single-stage process achieved products grading up to 61.3% KCI at recoveries up to 85.4% for the cationic flocculant suite and up to 64.8% KCI with recoveries as high as 90.3% for the non-ionic flocculant suite, with dispersant and flocculant dosages of 150-250gr1 and 10-75gr1, respectively. These results clearly demonstrate not only the feasibility of treating such problematic ores at low reagent dosages, but also the potential elimination of desliming prior to froth flotation.The experimental results presented are considered in terms of the reagent adsorption phenomena present in the system and various aspects of floe formation and cleaning.IntroductionAs high-grade sylvinite potash ores become scarce, lower grade sylvinite and carnallite potash ores are becoming more attractive. However, these ores often contain large amounts (up to 15% by weight) of water-insoluble slimes which must be removed prior to KC! flotation, owing to their high adsorptive capacity for the amine collectors used. The slimes are generally removed by scrubbing followed by hydroclassification and any residual material not eliminated is blinded with reagents such as guar gum or starch to inhibit interference in subsequent KC1 flotation.An alternative approach used commercially in Canada by Agrium Inc. involves water-insoluble slimes flotation prior to KC! flotation. In this process, the slimes are selectively flocculated and then separated by froth flotation. Losses of KC! to the slimes product and associated brine requirements are both reported to be less than those encountered in conventional desliming, but the technique is somewhat limited in its application at present."

Jan 1, 1997

By S. Kahraman, K. Develi, E. Yasar

Four hydraulic top hammers, one pneumatic top hammer, and three down-the-hole drills were observed in several rock types at quarries and highway construction sites to measure the performance data. At the same time, drill cuttings from each drill hole were collected for the determination of the coarseness index (CI), which is the sum of cumulative weight percentages of a particular size-graded sample of debris, and for the determination of median particle size (MPS), which is defined as the particle for which the quantity of particles equals 50% of the total of the cumulative distribution. After the sieve analysis was carried out on the drill cuttings in the laboratory, CI values were calculated and MPS values were obtained from the plots of cumulative undersize vs particle size. The performance data of the drills, CI values, and MPS values were analyzed using the least square regression method. It was seen that strong linear relationships usually exist between penetration rates and CI values, and penetration rates and MPS values for both top hammer drills and down-the-hole drills. Penetration rates increase linearly when increasing the CI and MPS values.

Jan 1, 2004

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By Y. L. Su, S. Vongpaisal, H. A. Smith

"It is extremely difficult for a mine&apos;s central control room operator to control peakpower demands and to maintain normal materials handling operations at the same time. An investigation of the Falconbridge Strathcona Mine &apos;s central control room has revealed that there are more than eight thousand possible combinations of ""situations"" that can arise. For such a circumstance, an expert system can become a very valuable tool to assist the operator in taking the most appropriate and timely action.A forward chaining expert system module has been developed for this application. The module is based on Level 5 ObjectTM software. It is graphics oriented and user-friendly. Training requirement is minimal.ForewordThis paper has arisen out of work carried out by YLS Associates and Falconbridge Limited as part of a contract between Falconbridge and the Department of Energy, Mines and Resources, Government of Canada, on the application of expert systems in mining operations.IntroductionThe electrical bill charged to large consumers by Ontario Hydro is based upon two elements: demand and energy consumption. The demand is the peak kilowatt level that the consumer has required during a monthly period. It is not uncommon for the demand portion to be as much as one third of the monthly bill. Energy consumption is the total kilowatt-hour s (kWh) consumed during the period.Ways to reduce the energy consumption part of the electrical bill involve utilizing energy-efficient equipment and operating machines in off-peak hours when a lower energy rate is charged. Maintaining the peak power below a critical level may require that simultaneous usage of major pieces of equipment be avoided. A 3000 kW skip run at an inopportune time could cost a company an extra $30,000 in that month&apos;s power cost.Potential disadvantages associated with peak power control are lost production due to work stoppage and increased operating costs due to the need to employ extra personnel. Most companies find these matters relatively easy to deal with and with incentives provided by Ontario Hydro, actively pursue this facet of energy savings (Harju , 1991)."

Jan 1, 1993

By B. J. Clauzier

"The Falconbridge Limited approach to employing communication equipment is first, to determine what is required in a given situation, second, to evaluate the possible alternatives, third, to select the most suitable hardware and, fourth, to determine what modifications, if any, are required to ensure not only successful implementation but continued low-cost reliability. Two examples are examined.The first situation required remote video monitoring of an acid loadout station. Several alternatives for linking to theremote site were investigated, including hard-wired, slow-scan and microwave. A comparison of these alternatives is shown and an appraisal of the performance of the selected microwave link is presented.The second situation required direct voice contact between the two members of an underground tram crew. Alternative solutions are described and an evaluation of the selected system- SHF portable radios - is presented.ObjectivesIn general, projects must have four main objectives: (1) to improve the safety of its operations; (2) to reduce its operating and capital costs; (3) to increase the efficiency of its work force; and (4) to increase its productivity. ScopeCommunication, when used wisely, can be a good tool to achieve these objectives. Projects can be kept simple using existing technology and adapting it to a particular task. To ensure the success of the project, it was necessary: to determine the project objectives; to evaluate the possible alternatives; to select the most suitable hardware; to adapt the hardware to the application, if required; and not to provide more than is necessary.Application at FalconbridgeTo illustrate this approach, two examples of actual installations at the Sudbury Operations are presented, sulphuric acid loadout, and the Falconbridge Mine haulage system."

Jan 1, 1987

By C. D. Shackelford, J. F. Muñoz, M. Vauclin, P. Rengifo, A. Suazo

The results of a field-scale study involving in situ leaching of copper ore tailings using sulphuric acid as the leaching agent, injection wells to introduce the leaching solution and extraction wells to recover the copper-enriched pregnant leaching solution are presented. The study was performed at an abandoned tailings disposal site using a battery of injection and extraction wells. The medium was characterized through the determinations of physical, chemical, mineralogical, and hydro-dispersive properties based on laboratory and field tests, including a tritium tracer test, a pumping test, particle size analyses, and hydraulic conductivity tests. Numerous horizontal strata with different hydraulic conductivities were identified. A previously developed model was used to simulate the leaching of copper ore tailings. Although the study confirms the feasibility of using in situ leaching for recovery of residual copper from tailings deposits, the efficiency of the technology depends significantly on the medium stratigraphy and hydraulic conductivity.

Jan 1, 2001

By Joel T. Werner

Tire costs represent one of the highest controllable costs in open-pit mining, accounting for approximately 10% of mining costs. Tire monitoring technology has evolved rapidly in recent years and is emerging as a viable tool for extending tire life and reducing costs. The majority of the major tire manufacturers and several independent companies are in various stages of developing monitoring systems that capture and store vital tire data. Previously this information had only been accessible when the vehicle passed a fixed point in the mine, or when mine personnel manually downloaded the data. Integrating this technology with a mine management system enables remote collection and management of trend and alarm data. Mine personnel can now monitor a tire?s health parameters at any time, anywhere on site, regardless of the vehicle?s location. Anomalous tire conditions can be detected early and corrective actions taken. This information can then be integrated with other major onboard systems, operating conditions, and geographical information. Tire monitoring no longer exists as a stand-alone technology, but has evolved into an important integrated tool for mine operators. This paper will review the current status and benefits of integrating this emerging technology with a real-time mine management system.

May 1, 2002

By P. A. Hacquebard, M. P. Avery

"Gondwana coal deposits are widespread and are known to occur in four continents. They are present in Brazil, India, South Africa, and Australia. From coal petrographic examinations and a detailed literature survey, it is interpreted that Gondwana coals are present also in Canada and the United States. Laurasia, or Northern Hemisphere, coals occur in the United States, Canada, and Europe. They form the main coal producing fields of the world. Megascopically, Gondwana coals have a uniform, micro-banded appearance, with a dull lustre; Laurasian coals are bright and have distinct bands of vitrain and clarain. Petrographically, Gondwana coals, compared to Laurasian coals, are lower in vitrinite, but higher in inertinite, particularly in semifusinite. Mineral matter averages 16% in Gondwana coals and 5.7% in Northern Hemisphere coals.Gondwana coals are characterized by thick seams that terminate through lithification (Versteinerung), whereby coal passes laterally into shale. Laurasian coal seams are thinner and terminate by splitting and digitation.Vitrinite/inertinite ratio data indicate deposition of the Gondwana coals in dry marshes under strong oxidizing conditions. The Laurasian coals originated in wet marshes in a reducing environment. As deduced from fossil plants and fossil spores, temperate and near arctic conditions apply for the Gondwana coals. A tropical and subtropical climate is indicated for the Laurasian deposits. The Gondwana coals were formed under allochthonous conditions. They derived from vegetation that drifted into the peat bogs. The Laurasian coals are autochthonous and originated from vegetation that grew and was buried in the peat bogs. The Gondwana coals are Late Carboniferous and Early Permian. The Laurasian coals are entirely Late Carboniferous."

Jan 1, 2004

By Daniel D. M. Adams

Over the last 100 years industry in general has been trying to advance the ability to maintain systems through management processes. Mining has looked to utilize onboard data systems in our mobile mining fleets to compliment these processes. Combining the two concepts build the concept that Rio Tinto refers to as asset health. These programs can generate a cost shift between $20,000 and $100,000 per piece of equipment annually. Even with the documented savings many operations struggle to justify the systems, why?

May 1, 2011

By David Evans, David Barnes, Robert Raponi

"The Williams Mine processes, on average, 6,450 t/d of gold bearing ore using two parallel grinding circuits, leaching and C.1.P., carbon stripping, electrowinning and refining. At present, each grinding circuit consists of a SAG mill in closed circuit with a spiral classifier and a ball mill in closed circuit with two stages of cyclones.Since grinding has always constituted the largest portion of milling costs, the Williams Mine has been proactive in trying to reduce such costs through innovative changes. One project under consideration is the replacement of one spiral classifier by a vibrating screen.This paper discusses the testwork performed to evaluate the replacement of one spiral classifier by a vibrating screen, and the preliminary engineering performed to date.IntroductionThe Williams Mine, located in northwestern Ontario, approximately 40 kilometres east of Marathon, is part of the Hernia gold camp. The mine is operated by the Williams Operating Corporation and is owned by the Teck Corporation and Homestake Canada Incorporated. Operation of the mine started in October 1985 at a rate of 3,000 t/d. After a mill expansion in August 1988, throughput increased to 6,000 t/d. Production has increased steadily since the mill expansion and in 1995, an average of 6,450 t/d of ore was processed at a recovery of 95.1 %."

Jan 1, 1997

By M. Kalin

"Ecological Engineering and Biological Polishing technology is a decommissioning approach for inactive coal, uranium and base metal operations. To improve acid mine drainage water some fundamental aspects of wetland ecology and sediment microbiology are combined, to provide conditions to allow for biomineralization of the contaminants.This paper summarizes the first records of microbial alkalinity generation in acid mine drainage through the utilisation of the ARUM process. The process requires that the seepage is at pH 4.5 where sulphate reducers utilize sulphate to produce hydrogen sulphide, which in turn precipitates with metals. The pH increase is brought about by alkalinity generating microbes.The ARUM process has been successful in increasing the pH from 2.5 to 7.0. Flow through reactors operated in the laboratory continuously for more than 60 days have removed Ni from 13 mg/L to < 0.01 mg/L. Design parameters are being developed for low flow rates of 5 L/min in a test system receiving seepage from a tailings.1.0 INTRODUCTIONAcid mine drainage associated with mining wastes poses a significant environmental problem. Conventional means to treat acid mine drainage (AMD) use chemical treatment system. Ecological Engineering technology uses natural biological means to curtail and ameliorate AMD during mine operations and at the time of decommissioning. The premise underlying Ecological Engineering technology is that AMD is the result of a natural process enhanced by mining activities. Therefore, in nature, a process providing a natural balance to AMD has to exist, which, when assisted through appropriate means, can counteract the detrimental effects of AMD on the environment. This process is microbial alkalinity generation which is known to occur in wetlands, lake and ocean sediments (Baas Becling et al, 1960)."

Jan 1, 1991

By Mike Samuels, John Starkey

"This paper examines test results and grinding mill design for the recent Fortune Minerals’ NICO Project, located in the Northwest Territories. SAG milling and rod milling options are compared. Rod milling is clearly shown to be the best option because of the ore’s extreme resistance to breakage in a SAG mill environment.Surprisingly, the Bond Ball Mill Wi was 13 kWh/t for this ore. The Bond Rod Mill Wi was 20 kWh/t, whereas the SAG pinion energy to grind the ore to T80 1.7 mm was 30 kWh/t. The existence of ore with this ratio of SAG hardness to Bond BM Wi has not been previously observed. If not considered, this critical relationship may adversely impact the accuracy of mill design. This paper substantiates the significance of these findings to achieve successful grinding design on ore that is macro-competent during primary size reduction, but relatively normal during secondary grinding.INTRODUCTIONThe NICO Cobalt-Gold-Bismuth-Copper deposit is located 160 km northwest of the City of Yellowknife, Northwest Territories. It is the largest IOCG-type deposit (aka Olympic Dam-type) currently recognized in Canada with Mineral Reserves of 21.8 million tonnes contained within a larger 57 million tonne, lower-grade Mineral Resource. The project, owned 100% by Fortune Minerals Limited, has been assessed in a positive definitive feasibility study, subject to underground test mining and pilot plant testing, and is now in the permitting stage to develop a combined open pit and underground mine and process plant. An updated process flow sheet incorporates conventional crushing, grinding and bulk flotation, followed by filtration for shipment of a concentrate to a purpose-built refinery proposed to be built near Saskatoon, Saskatchewan. At the refinery, separate bismuth and cobalt concentrates will be produced following regrinding. The hydrometallurgical process methods include: pressure acid leach, precipitation, ion exchange, and electro-winning for recovery of cobalt as 99.8% cathode; solvent extraction and electro-winning of by-product copper cathode; ferric chloride leach and electro-winning for recovery of bismuth as 99.5% cathode; and cyanidation of the leach residues for recovery of gold as doré."

Jan 1, 2010

By D. Simon

This paper studies the effect of binder type and content on the early age development of cemented paste backfill (CPB). The early age development of the mixtures is analyzed using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDX). These tests show that the early age development of CPB is sensitive to changes in the paste composition. The properties of the CPB depend on the cement content and hydration time. The quantity of hydration products increases with hydration time for all of the mixtures containing cement. However, the high cement content pastes (at least 50% PC) exhibit complete coverage of the PC grains and mine tailings by C-S-H, while the low cement content paste shows scattered coverage of the PC grains and mine tailings and a higher void ratio.

May 1, 2007