Search Documents

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit's maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By G. L. Zhu, Y. F. Wu, H. Nagaumi

A novel eutectic-type alloy Al12Si-HTC with high thermal conductivity has been developed by strict chemical composition control and heat treatment. The thermal conductivity of the alloy is about 30 % higher than that of current commercial Al12Si alloy. The Al12Si-HTC alloy has a silicon content of 10~12 wt.%, which provides excellent castability. Trace element strontium or calcium is added to modify eutectic silicon, and contents of transition elements such as copper, manganese are controlled in a low level. By appropriate heat treatment, thermal conductivity of the castings increases by 7.5 % and finally reaches 172 W/(m·K). It is found that eutectic silicon modification which makes average particle size finer than 2µm plays a dominant role in improving thermal conductivity, as well as further spheroidization of eutectic silicon and reduction of lattice defects in a-Al microstructure in subsequent heat treatment process. The alloy is successfully applied to produce a certain communication enclosure with complex finned structure by die casting process in industrial scale. The results of numerical simulation and thermal analysis experiments show that when manufactured by Al12Si-HTC alloy, the surface temperature of chips in the enclosure is reduced by 2.0~4.5 ? and the temperature distribution is more homogeneous compared with traditional Al12Si alloy.

Jan 1, 2015

By O. C. Rojas, J. Sanhueza, J. C. Vargas

Empresa Nacional de Minería (ENAMI) is dedicated to the promotion of small and mid scale Chilean mining industry. Paipote, ENAMI Copper Smelter, processes a variety of mineral products as the result of this promotion. The mineral products characterize a wide variation of copper, iron, sulfur and precious metals content as well as the significant dispersion in the content of impurities, such as arsenic, antimony and bismuth. The Smelter Modernization Program, initiated in1997, introduced a series of technological and operational changes. The development of operational planning and control strategies was necessary to optimize the blending of a wide variety of concentrates and the control of metallurgical processes in order to ensure the stable operation, fulfillment of environmental regulations and the quality of produced copper anodes. A permanent optimization process carried out in the last decade led to the permanent increase of the smelting capacity and the production of anodes and sulfuric acid. Additionally, introduced improvements affected the smelter efficiency and metallurgical recovery, demonstrating the possibilities of the optimization of a small smelting facility reflected in good metallurgical and economic results. This paper presents the smelter evolution, introduced technological and process control changes as well as incorporated new reactors and equipment as a continuous process of optimization.

Jan 1, 2007

By L. Heber Cole

Introductory During the past few years, salt (sodium chloride) strata have been encountered in western Canada in a number of wells, while prospecting for oil and gas. The ever increasing number of such wells points to the presence of a vast salt basin, the boundaries of which are at present unknown. This basin extends in a northwesterly direction from a point near the United States boundary south of Regina, crosses the Saskatchewan- Alberta boundary northwest of Unity, Sask., and continues with more northerly trend to Waterways and beyond. The beds, as encountered, appear to have a general dip to the southwest of between 10 to 20 feet to the mile and a pitch along the strike to the southeast. Thus one finds the salt strata at Waterways, Alta., at 600 feet below the surface (121 feet above sea level) whereas at Radville, Sask. south of Regina, the top of the salt is at a depth of 6,643 feet below the surface (4,430 feet below sea level). Whether this is a continuous salt basin or a series of separate basins is not yet known. We do know however, that in some of the well~ more than one salt horizon occurs while in others which normally should have encountered corresponding beds, the salt strata are absent. This latter condition, however, may occur only in the southern part of Saskatchewan, where a barren area seems to come in from the southwest. In the northwestern part of the basin, on the other hand, the occurrence of the salt strata seems to be more regular and continuous, and depths at which salt should be encountered in a drill hole in this part of the basin may be predicted with a fair degree of accuracy.

Jan 1, 1948

By F. T. Rabbitts

Introduction When the investigation of radioactive ores began at the Mines Branch about five years ago it was at once evident that improved chemical methods for the determination of uranium were essential. The published methods available were time-consuming and insensitive and were lacking in accuracy and precision. It was desirable to obtain methods which would be rapid, sensitive, and accurate. They should also allow for the possible presence of any interfering elements and should be adaptable to routine analysis by technicians. Chemical methods are necessary to provide standard analysed samples for counting and to check analyses by counter methods. Moreover, counter methods cannot be used, and only chemical methods are suitable, when the sample is not in equilibrium, as with weathered minerals and leach residues. As leaching processes are improved, more sensitive chemical methods are required for the increasingly lower content of uranium in the leached residues. When the leaching process reaches the plant stage, speed of analysis becomes more important, without sacrificing accuracy. The purpose of this paper is to describe briefly .the methods used at the Mines Branch for the chemical analysis of uranium in ores. These methods represent the results of investigations by a number of groups in the United Kingdom, the United States, and Canada.

Jan 1, 1952

By R. A. May, P. J. Brooks, W. M. Smith

"Neill and Gunter Limited (NGL) has prepared a preliminary design and a cost estimate for a ferric chloride leach plant to recover copper, lead, zinc, and silver from a typical complex sulphide ore. This plant design is specifically intended to treat unconcentrated ground ore (flotation feed), but can be readily adapted to treat bulk concentrates. Samples of ground ore and bulk concentrate were obtained from Heath Steele Mines, Miramichi, New Brunswick, laboratory testing, and preliminary process flow sheet preparation was carried out by the Research and Productivity Council in Fredericton, New Brunswick. Approximately thirty drawings have been produced, including process and equipment flowsheets, process piping and instrumentation drawings, and preliminary general arrangements. Preliminary capital and operating cost estimates were prepared for a plant that would treat 1000 t/d of crushed and ground ore to produce about 30 000 tpy of zinc. Capital and operating cost estimates were also projected for plants up to 4000 t/d of processed ore. Recoveries of 99% for zinc, 98% for lead, and 96% for copper were achieved in laboratory tests on unconcentrated ore. These recoveries were higher than the overall recoveries obtained from bulk concentrate, yielding approximately 10% more revenue.A 1000 tonne per day plant was determined to have a low return on investment, however, depending on the size and type of mining operations employed and the FCL plant throughput. DCF-ROI projections of 20% to over 30% were calculated for 100% equity financed “green field” mine, mill and FCL plant operations of 2000 t/d and higher"

Jan 1, 1997

By K. Lascelles

ABSTRACT Nickel compounds vary significantly in their toxicological properties, so it is critical that continuing studies to accurately quantify worker exposures consider the processing that accompanies refining nickel-containing materials. The Clydach nickel refinery, which has operated for more than 100 years, was the first nickel-producing facility to show a high risk for lung and nasal-sinus cancers among workers employed since it opened in 1902. Process chemistry and equipment have changed dramatically over Clydach’s history. This paper describes the processing evolution at Clydach with a focus on the propensity for aerosol formation and the forms of nickel in airborne dusts.

Jan 1, 2013

By Jae-Chun Lee, Rajiv Ranjan Srivastava, Min-seuk Kim, Byung-Su Kim

Recycling of spent hydrotreating catalysts (HTC) can potentially contribute towards the sustainable extraction of metal values. Treating such materials by hydrometallurgical methods to separate metals from the leach liquor of either acid/alkali media is a major step. In the present study, separation of molybdenum from HCl leach liquor of spent NiMo type HTC has been investigated by applying solvent extraction using Cyanex-923. For this, the chloride solution containing 973 mg/L Mo, 254 mg/L Ni and 1634 mg/L Al was taken as the aqueous feed. The parameters including contact time, concentration of the extractant, acid and chloride, and phase ratio were varied to investigate their effect on the extraction efficiency. The McCabe-Thiele plot suggests that > 99% Mo-loading using a 2-stage extraction process. From the molybdenum depleted solution, nickel was selectively extracted by Cyanex-301 leaving Al in the raffinate.

Jan 1, 2014

By J. A. Drozdiak

In this paper we examine, through pilot-scale testing, the possibility of operating a circuit comprised of two stages of HPGR comminution, followed by grinding through a horizontal stirred mill. In order to assess whether the novel circuit design could achieve the reduced energy requirements indicated in the literature, two more-established circuits, a cone crusher / ball mill and an HPGR / ball mill, were examined using a combination of testing and flowsheet simulation. The results showed that, based solely on the specific energy requirements for comminution, the HPGR / stirred mill circuit achieved a reduction of 9.2% and 16.7% over the HPGR / ball mill and cone crusher / ball mill circuits, respectively.

Jan 1, 2012

By Arthur Dubé

An account is given of the developments brought about in the last fifteen years by metallurgical research in the field of heat treatment of steels. The practical aspects of these developments are especially emphasized. Methods of representation of the phase-change during austenitizing and sub-critical transformation of austenite are described and the importance of time-temperature-transformation charts for the planning of heat treatment cycles is shown. Special copies such as retained austenite and internal stresses developed on quenching are also discussed in some detail. Due to the interest shown currently in these problems, it has been thought advisable to describe briefly the underlying principles and present some of the results already available.

Jan 1, 1945

By R. Bainbridge

THE cinnabar deposits of the Consolidated Mining and Smelting Company's Pinchi Lake property, situated near Fort St. James, B.C., were discovered and reported on by a Dominion Government geological party in 1937. Claims were staked by a group of local prospectors and, later, the Consolidated Mining and Smelting Company of Canada, Limited, took an option on the property. By the fall of 1939, exploration work had indicated ore of commercial quantity and grade, and laboratory tests had shown that standard methods of reduction, namely, roasting of the ore, followed by condensation of the mercury vapour produced, would result in satisfactory recovery. In June, 1940, construction of a 50-ton unit arranged for wood firing was completed and operation commenced. The installation consisted of a 46 in. by 60 ft. rotary kiln (see Figure 1) followed by a 14-in. Sirocco cyclone, a cast-iron condenser unit, and a 1,700 c.f.m. fan, exhausting to a stack. Other equipment included a 9 in. by 18 in. Denver jaw crusher with the necessary bins and feeders. As the need for mercury was urgent, because of war requirements, construction of a duplicate unit was begun almost immediately. This first extension started operation in January, 1941, and the plant was then capable of treating about 150 tons of ore daily.

Jan 1, 1945

By G. K. Quainoo

In the automotive industry, the awareness to meet Corporate Average Fuel Efficiency (CAFE) standards has evolved the need to reduce vehicular weight in new automobile designs, with the overall goal of reducing gas emissions into the atmosphere (Kyoto protocol), One efficient method has been to use lighter materials such as aluminum in outer body panels, Heat treatable AA6111 is one of the materials employed due to its unique combination of formability, paint bake strengthening and superior corrosion resistance characteristics, Researchers have applied various thermo-mechanical processes on 6000 series aluminum alloys and have found an improvement in the mechanical properties of these alloys, For a formed and painted automobile panel, the final mechanical properties involve a combination of strength components arising from cold work, strain aging and precipitation minus recovery. In this study, the evolution of microstructure resulting from the interaction of cold work and precipitation in AA6111 has been studied by means of transmission electron microscopy (TEM) after subjecting samples to various heat treatments, tensile testing and differential scanning calorimetry (DSC), This has been done to understand the evolution of microstructure and its influence on the properties of the alloy, The results show a considerable improvement in strength with a corresponding increase in strengthening precipitates with increasing level of cold work in the alloy. DSC results following the application of various levels of cold work also show acceleration in the precipitate phase formation, as precipitates are observed to form at lower temperatures, with increasing level of cold work/

Jan 1, 2005

By P. J. Bourassa

Incorporated in 1957 under the laws of the Province of Quebec, Quebec Cartier Mining Co. undertook the development of its low-grade iron ore reserves located at Lac Jeannine in the southwest extremity of the Quebec-Labrador trough. This challenge comprised the construction of a 200-mile access road, two towns, a 191-mile-long railroad from Port Cartier to Lac Jeannine, a hydro-electric generating plant on the Hart Jaune River, and mining, crushing, concentrating and ancillary facilities to support a yearly production of 8.0 million tons of iron ore concentrates at 66% Fe. In order to meet increasing market demands for iron ore concentrates concurrently with the depletion of its Lac Jeannine reserves , Quebec Cartier announced, late in 1969, the first step toward bringing into production a new iron ore deposit, known as Mount Wright, located 70 air miles northeast of Lac Jeannine and 25 miles southwest of Labrador City, Newfoundland. In September 1970, the company announced its decision to develop and bring into production its Mount Wright reserves at an annual rate of 1 8.4 million dry long tons. The scope of this project included the construction of an access road linking the mine, the new town and Labrador City, Newfoundland, the extension of the railroad by some 86 miles, the construction of an ore concentrating plant with all the ancillary facilities, the development: of the mine, the construction of a pourer transmission line and a new town adjacent to Lake Daviault. The Mount Wright story is divided into five individual papers covering: (a) the history and development of the project; (b) the mine; (c) plant control by a process computer; (d) crushing, grinding and concentrating; and (e) the townsite of Fermont.

Jan 1, 1977

By A. Navarra, C. Arrancibia, R. Yañez, C. Acuña, F. Valenzuela

"Discrete event simulation (DES) is a suitable framework to evaluate and optimize the dynamics of sulphide smelters. In particular, iron-nickel-copper-cobalt sulphides undergo continual oxidation within a roasting or smelting operation, followed by batch oxidation within the converting operation, thus producing iron-free Bessemer matte (or blister copper, in the case of copper smelters); this semi-finished product undergoes further processing to produce nickel, copper and cobalt products, and to recover precious metals. The juncture between continuous smelting and batch converting is often an appropriate focus for the earliest phases of DES development, since it is typically a major bottleneck within nickel and copper smelters; later phases may include increasing levels of detail for auxiliary unit operations, as well as plant logistics. Moreover, DES can support matte-slag chemistry, including Gibbs free energy balances to determine the iron speciation within the slag. DES is therefore capable of linking the fundamentals of oxidation reactions to the intricacies of plant dynamics.INTRODUCTION Discrete event simulation (DES) is gaining acceptance within the extractive metallurgy community, as a technique that quantifies the system-wide performance of metallurgical plants under conditions of uncertainty (Wheeler & McGinty, 2015). In particular, over 90% of smelters that process nickel-copper-cobalt sulphides and copper sulphides exhibit similar semi-continuous dynamics (Crundwell et al., 2011b; Schlesinger et al., 2011b), in which the converting aisle produces batches of material that are sent for further processing (Figure 1). Thus the tools and practices that are developed for a specific sulphide smelter are often relevant to numerous other smelters.The juncture between continuous smelting and batch converting has long been a focus for discrete event simulation (Welgama et al., 1996). Nonetheless, the broad acceptance of DES in nonferrous smelters has been hindered by interdisciplinary barriers that divide industrial and metallurgical engineers (Navarra et al., 2016; Noorossana et al., 2012); this divide has been less severe in steel plants (Hollocks, 2006). In recent years, DES has been used in copper smelters to analyze crane-and-ladle motions (Coursol et al., 2009a), reverts production and consumption (Noorossana et al., 2012), and innovative control systems (Herrera et al., 2016); additionally, DES models have accounted for shutdowns and random breakdowns to provide realistic assessments of copper smelter capacities, thus guiding equipment upgrades (Campbell et al., 2013; Coursol et al., 2009a). All of these studies feature a Peirce-Smith converting aisle similar to Figure 1 that, under normal operations, constrain the smelter throughput, and are thus a bottleneck (Campbell et al., 2013; Navarra et al., 2016)."

Jan 1, 2017

By George P. Demopoulos, Yan Zeng, Zhibao Li

Precipitated silica is marketed with a rising demand as reinforcing filler in the rubber industry and as a potential raw material for the synthesis of lithium-ion battery electrodes. Due to an awareness of the environmental impact of the existing processes for the production of precipitated silica, a green and sustainable process was proposed by using sodium bicarbonate (NaHCO3) as an alternative to sulfuric or hydrochloric acid in the precipitation reaction with sodium silicates. The use of NaHCO3 allows for better control of the supersaturation and pH to form silica with desired quality. Additionally, Na2CO3 solution as the process by-product is recyclable because it could be recovered to produce NaHCO3 by absorbing CO2. The solubility of sodium metasilicate nonahydrate (Na2SiO3·9H2O) in the Na-CO3-HCO3-OH-H2O system was measured using a dynamic method in the temperature range from 288.15 to 308.15 K. It is found that the solubility of Na2SiO3·9H2O decreases with increasing concentration of either Na2CO3 or NaOH over the investigated concentration range. With the aid of the OLI platform, a chemical model for the Na2SiO3-Na-CO3-HCO3-OH system was established with newly obtained interaction parameters of the Bromley-Zemaitis model by regression of experimental solubility data. The new model predicted the solubility of Na2SiO3·9H2O in multi-component systems with good agreement and was used to conduct a preliminary feasibility study of the new process.

Jan 1, 2015

By S. D. Graham

"The extractive metallurgy of gold is largely controlled by mineralogical factors such as the presence of refractory gold, particle size, gangue mineral associations, presence of preg-robbers, oxygen and cyanide consumers, and locking characteristics in base metal sulphides. Light microscopy and automated mineralogy techniques are regularly used to characterise the effect of these variables on gold recovery. However, despite their widespread application there are a range of limitations when grades are low. Typically, the analysis of low-grade samples requires the preparation and analysis of numerous polished blocks. This is often costly and time consuming, with complexities regarding analysing statistically representative particle quantities and problems overcoming stereological bias. This is compounded by the “nugget” effect and high tenor nature of gold mineralisation. X-ray Microscopy techniques have the potential to overcome many of these problems, in particular the statistical representivity of analysis, removing stereological bias and effectively locating phases that are present in ultra-trace proportions. In this paper we outline the potential benefits of employing X-ray Microscopy (XRM) in characterising gold losses from a typical Cu-Au porphyry project, which were illusive in 2D based analysis. The talk will also outline additional application areas of XRM within the extractive value chain."

Jan 1, 2017

By M. Girard, E. Bourricaudy, M. Ashbury, M. Canizares, A. Mezei

Liquid-solid separation and slurry handleability relate directly to commercial plant ramp-up success or lack thereof. The paper provides a well-proven approach for testing, scale-up and commercial application of difficult processes. Emphasis is placed on practical applications of rheological concepts developed both academically and empirically. The cause-effect relationship between the process chemistry and possible physical implications on the metallurgical plant operability is presented in a simple, direct form. Examples include recent results in areas of mineral processing and extractive metallurgy. Technical process risk factors and their mitigation are included in the discussion.

Jan 1, 2011

By J. -F. Lepage, M. A. Tomlinson, K. K. Murray

"The Éléonore mine, located in the James Bay region of Northern Quebec, generates a gold bearing flotation concentrate rich in pyrrhotite. Direct leaching of the finely ground concentrate results in high cyanide consumptions and poor recoveries, so effective pre-treatment to passivate the pyrrhotite is required before leaching. Following a number of process upsets at the mine, test work was performed to better understand the requirements for passivation so a more effective operational strategy could be implemented. This paper outlines the testing and implementation of the new strategy at Éléonore.ÉLÉONORE CONCENTRATOR The Éléonore mine is located 800 km north of Montreal, in the James Bay Region of Quebec, Canada. The ore, containing gold disseminated in sulfide minerals and free fine gold in silicate gangue, is crushed in a two-stage crusher plant before being ground in a single 9,000 kW ball mill. The ball mill is in closed circuit, with about 25% of the cyclone underflow passing through a gravity plant with two, 48” Knelson concentrators. Gold recovery in the gravity circuit varies between 15 and 20%, with gravity concentrate leached daily in an Acacia intensive leach reactor. Cyclone overflow, at a target P80 of 65 microns, flows to the flotation plant where the gold bearing sulfide minerals, mainly pyrrhotite and arsenopyrite, are recovered to concentrate with a mass pull of about 5%. The flotation concentrate, typically containing between 80 and 120 g/t of gold, is thickened and finely ground using a 1500 kW Isa Mill. The finely ground concentrate is diluted, to generate a slurry with about 32% solids by weight, before feeding the leach plant. Initially the concentrate slurry is pre-treated with oxygen and lead nitrate, to passivate the sulphide minerals before cyanide is added for gold dissolution. Gold is recovered from the leached slurry using carbon-in-pulp (CIP). The flotation tailings are also thickened and gold is recovered in a dedicated leach-CIP plant."

Jan 1, 2017

By F. Awotwe-Appiah, P. Koshy, A. Y. Fosu, J. Dankwah, J. R. Dankwah

Ghana currently exports its bauxite raw without any value addition. Gradual depletion of high grade bauxite (with high alumina content) and the emergence of low grade bauxite (with high iron oxide content) calls for novel and inexpensive ways to recover alumina from these low grade ores. Bauxite users have indicated their willingness to pay 10% to 50% higher for a corresponding reduction in impurities by a similar amount. This project therefore investigates the carbothermal upgrading of the Ghana Awaso bauxite using waste polypropylene as reductant in a locally designed gas-fired furnace. Composite pellets of low grade bauxite sample (assaying 45% Al2O3) containing pulverised waste polypropylene were formed, oven dried, placed in fireclay crucible and fired for 30 minutes. The magnetic fraction after reduction was separated by a Low Intensity Magnet and weighed. It was observed that up to 97% of the iron oxides (occurring as hematite and goethite) could be separated into the magnetic fraction as magnetite leaving a nonmagnetic fraction with over 98% Al2O3 as opposed to the 45% Al2O3 in the as-received bauxite sample. This research direction provides yet another simple but effective way for simultaneously upgrading low grade bauxite and recycling waste polypropylene, whilst at the same time decreasing the amount of waste material generated as red mud after the Bayer process.

Jan 1, 2015

By H. C. Boydell

Those connected with mining, prospecting, or mining geology in northern Ontario are familiar with the fact that it is a comparatively unusual thing to have assayed a sample for which the assay report shows no gold. Values of 20 cents to 80 cents per ton, or even higher, are extremely common. Whilst contamination by fluxes, faulty manipulation, or a desire, on the part of the assayer, to sugar-coat the pill for the client, may account for 20 to 40 cent values at times, it is un1ikely that they would a1ways do so. Exonerating the assayer from being necessarily at fault, what can be the cause of such a widespread distribution of gold (and silver) in minute quantities- of a dissemination .that, in the writer's experience, and so far as he is? aware, is not met with on a simi1ar scale in other parts of the world? Explanations that suggest themselves are, that the dissemination is due: 1. To a very widespread auriferous minera1ization, post-dating (epigenetic) the formation of the rocks in which it occurs. 2. To a general syngenetic distribution of gold in the volcanic rocks of Keewatin age that form so large a part of the sections of northern Ontario that have been prospected.

Jan 1, 1928