Search Documents

By A. Y. Senchenko, Y. V. Kulikov

"Different methods aiming at specific energy calculation and design of AG/SAG circuits are used in mining. They include JK DWT/SMC test, SAGDesign test and CWi/RWi/BWi tests. The simplest methods with no secret equations and giving energy required for grinding in kWh/t were proposed by F.?. Bond and J.H. Starkey. D.J. Barratt proposed to use results of CWi/RWi/BWi tests for AG/SAG mill sizing. The present paper gives an alternative for forecast of specific AG/SAG energy. The principle is similar to the theory proposed earlier and consists in cumulative AG/SAG energy calculation using indices of rod and ball grinding (RWi+BWi) without impact crushing index (CWi). Then total energy is divided between two grinding stages using special formulas based on extensive statistical information. The forecast indices of AG/SAG and ball grinding are similar to the SAGDesign testing results. Hereinafter the predicted indices are used for mill sizing of the whole grinding circuit. The method considered in the paper enables prediction of AG/SAG energy based on the test results according to Bond method. The proposed method version was not widely published earlier. The aim of the work was to elaborate cost-effective, reliable and accessible way to determine specific AG/SAG energy. At this stage of method development, it is recommended to use it only for works at preliminary Geometallurgy stage (Scoping, Pre-Feasibility). At design stage the obtained data should be confirmed by appropriate testing using alternative JK DWT/SMC and SAGDesign methods.INTRODUCTIONAppropriate crushing and grinding testing is required to design efficient comminution circuits. It is obviously important to obtain accurate information about ore hardness properties since the main energy consumption at the plant is associated with comminution processes. Moreover, it is required to apply the processes that make it possible to minimize operating costs and efficiently use capacity of the installed equipment installed.When studying ore hardness properties, it is required to take into account that breakage of the material is performed using different equipment. That is why accurate selection of the equipment and the circuit calculation without relevant testworks is impossible. Ideally, the testworks should provide answers to the following questions: determination of ore hardness properties, determination of specific energy consumption for comminution as well as obtaining of sufficient amount of statistically significant results from the tests. The results from crushability and grindability testworks in the first place provide assessment of ore hardness properties and in addition correlate with throughput of the respective equipment. The data obtained can be used for modeling of comminution circuits at the stage of the technology development"

Jan 1, 2016

By R.P. Edwards, B.C. Flintoff

Froth flotation is one of the most widely used and effective processes for mineral benefication. First introduced in 1911, flotation technology has seen many developments over the past 80-plus years. Innovations in reagent chemistry, equipment design, process analysis and process control have given design and plant engineers a powerful set of "tools" for process optimization. However, it does not follow that all flotation systems are optimized. As Klimpel observes: "The problem with the industrial flotation process is that it is relatively easy to get reasonable results, and relatively difficult to get excellent results." Klimpel [1988] While reasonable was sufficient in the past. competitive forces will make excellent necessary in the future. Judging by the activities in many Canadian plants this transition is already underway.

Jan 1, 1995

"Yara Siilinjärvi in Finland is the Western Europe's only apatite mine. Annually it produces one million tons of apatite concentrate, which creates 10 million tons of tailings. At the beginning of 2017, Yara replaced their conventional TSF with a new tailings treatment plant, which increased the solids content of the slurry from 45–48% to 66–68%, making it possible to deposit as a paste. This extended the life-span of the current TSF from 2020 to 2035. This paper presents the storyline of the Yara paste plant project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After successful pilot trials, the final process design was implemented. Process automation played a key role in the project. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances. Since commissioning the paste plant has been running consistently with an underflow solids content of 66-68%, with average beach slope angles of 3.5 degrees in the tailings disposal area. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the plan. During first year of operation the plant’s availability has been very good, over 97%, and currently, the plant is operated remotely from the main concentrator plant.INTRODUCTION The Yara Siilinjärvi Plant is owned by Yara International, a Norwegian fertiliser company. Yara Siilinjärvi is Western Europe's only apatite mine, and it primarily produces apatite concentrate for its Siilinjärvi phosphoric acid plant. A portion of the concentrate is also dried and shipped to other Yara fertiliser plants. The site annually produces one million tons of apatite concentrate, which creates approximately 10 million tons of tailings. Extending the lifespan of the 1150-hectare tailings storage facility has been studied in Siilinjärvi for a long time. The aim has been to use the same tailings area footprint, without any new land purchases or major dam increases. An important part of the process has been to study the possibilities for using new technologies, especially thickened tailings technology (Ruhanen, 2014)."

Jan 1, 2019

By P. Srinivasan

Corrosion is a major operational problem in amine-treating plants causing significant expenditures each year, Corrosion may become more severe when the amine plants contain process contaminants ? namely heat-stable salts. The heat-stable salts enter the plants with feed-gas streams and makeup-solution, and/or are produced within the plants by reactions of alkanolamine and available carboxylic-acid anions, This work investigated interaction corrosion effects that may exist in amine-treating plants containing a mixture of heat-stable salts, The investigation was experimentally carried out in a 5 kmol/m3 monoethanolamine (MEA) solution containing 0,20 mol/mol carbon dioxide (CO2) loading at 80°C under atmospheric pressure using carbon steel 1018, Six heat-stable salts, including formate, oxalate, bicine, acetate, thiosulfate and chloride, were tested with a series of salt combinations, Potentiodynamic Polarization, Tafel Extrapolation, and Cyclic Polarization were used for revealing corrosion behavior, determining corrosion rate, and examining the pitting tendency, respectively, Results show that thiosulfate induces the most corrosive environment when present either individually or in the form of salt mixtures.

Jan 1, 2005

The University of New South Wales (UNSW) has been a world leader in the development of innovative virtual reality technologies over the last 10 to 15 years. These developments have included developing the world?s first 360° surround, virtual reality (VR), stereo projection theatre system known as AVIE (Advanced Visualisation and Interactive Environment), which was developed by iCinema, a collaborative venture between the UNSW Faculties of Engineering and College of Fine Arts. The UNSW School of Mining Engineering has been responsible for development of mining applications virtual reality software modules and to date, has developed eighteen different mine safety training and mining engineering education modules which run in the AVIE environment. This platform and technology package provides a unique ?immersive environment? experience for groups of trainees or students who can engage with the simulated environment in the complete safety of the virtual reality theatre. In all of the major international mining industries, safety is of paramount importance, and training of personnel is an essential component of any comprehensive proactive safety management system. All personnel need to be aware of the inevitable hazards around them at all times, as well as understand appropriate safety and operational procedures. This can be done by conventional class-room style training sessions, or by provision of training documentation. However the effectiveness of such systems is often very limited due to the inability of trainers to engage with the audience for a lengthy period of time; or to convey the often complex and variable mining environments and situations which can exist in a typical mine. The ability to immerse the trainees in a virtual mine environment, with all the reality of an actual mine but with none of the physical exposure to actual hazards, provides a far more effective and engaging training experience. Furthermore, in the virtual world, trainees can be exposed to the very unlikely, but nevertheless high consequence hazards such as mine fires, falls of ground or outbursts, without any risk to their safety and well-being. The end result is that trainees will be far more engaged with the learning environment they find themselves in, and will develop a far higher level of understanding of the topics, rather than simply experiencing a passive class-room style learning environment offered by conventional training modes. The UNSW systems have been implemented widely within the Australian mining industry and the mining engineering education sector and are now being adopted internationally. This paper presents an overview of the innovative technologies involved in these virtual reality systems ? as applied to the mining industry. Modules developed for both mineworker training and mining engineering student learning will be presented, to illustrate the effectiveness and value of such a training and education approach.

Aug 1, 2013

CSIRO Minerals, in association with the AJ Parker CRC for Hydrometallurgy, has an active program of hydrometallurgical research in which physical and computational modelling are used to better understand and improve a range of different unit operations. The modelling is based on flow simulation (Computational Fluid Dynamics or CFD), but incorporates other physical and chemical phenomena of importance, such as droplet break-up and coalescence, species transport and reaction. This paper reviews some of the major projects that have been undertaken at CSIRO Minerals and will illustrate the critical importance of hydrodynamics to the performance of unit operations and the improvements that can be made to performance using such modelling techniques. Unit operations that are discussed include solvent-extraction, gravity thickeners, flotation cells, bio-heap leaching and stirred tanks.

Jan 1, 2005

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By P. Leo

The hot deformation behavior of a Mg-9A1-1Zn alloy produced by high pressure die casting has been investigated by means of compression tests in the temperature and strain rate ranges of 125-300°C and 10-5-10-1 s-1 and torsion tests over 150-450°C and 5, 0.5, 0.05 5-1 . The compression samples were deformed in the die-cast state or after homogenization at 415°C for 2 h to evaluate improvements. A premature fracture at 45° with respect to the compression axis was observed in samples strained at low temperatures and high strain rates. The torsion specimens were tested as received or after a predeformation-homogenization treatment. In addition to constitutive analyses suitable for modeling previously published, the results are fitted to a relationship between strain rate normalized by diffusion coefficient and flow stress normalized by modulus. The results fit well with a set of published creep experiments that were conducted in the range of 70-150°C.

Jan 1, 2006

By Jason Berenyi

Presentation Overview ? What is Potash? ? Where are the potash deposits? ? Current potash mines ? production, capacity and planned upgrades ? Saskatchewan Saskatchewan?s Potash Production Potential s ? Current Status of Potash Exploration ? Increasing Demand for Potash ? Saskatchewan global role

May 1, 2009

By K. Esmaieli

The Synthetic Rock Mass (SRM) approach has the potential to capture the mechanical behavior of large rock samples. In order for the method to be used with confidence it is necessary to gain a good understanding of the factors that influences its analysis. This paper reports on a series of numerical experiments, based on field data from a large underground mine, to investigate the influence of intact rock mass strength of a constructed (SRM). A jointed rock mass defined by three fracture sets was simulated by a Discrete Fracture Network (DFN) model. The generated fracture network was subsequently embedded into six different intact rock samples, simulated by a bonded particle model in PFC3D, generating six SRM samples. Each intact rock sample was 7 m × 7 m × 14 m and assigned different mechanical properties. The first intact rock sample was assigned a uniaxial compressive strength of 205 MPa and an elastic modulus of 104 GPa with the UCS and elastic modulus values of the other samples downgraded by 10% until the weakest sample had a UCS value of 121 MPa and an elastic modulus value of 61 GPa. All SRM samples were loaded under uniaxial compression to obtain the complete stress strain curve. It was observed that the compressive strength of the rock mass samples decreased by 10% following the same trend as the rock material strength. However, the elastic modulus of the rock mass samples decreased non-linearly with reduction of the elastic modulus of the rock material. The Poisson's ratio of rock mass samples does not change with decrease of rock material properties. For the post-peak behaviour the results show that both the brittleness index and the residual strength of rock mass samples decreased as the rock material properties degrades.

Aug 1, 2013

By A. Trusiak

"Increasing energy costs in mineral processing is making it necessary for tighter controls over various parts of the concentrating process. Continuous monitoring and control of critical process streams can be easily performed by today's many computer systems. Indeed, the list of successful applications of computers to grinding and flotation control continues to grow. The day is rapidly approaching when the use of computers within concentrators for either process control or simply metallurgical accounting will no longer be a luxury, but a necessity. The benefits from such applications far out weight the initial investment.This paper describes the current application of a process control system at Brunswick Mining in north-eastern New Brunswick. Emphasis is placed on the control of a CuPb flotation circuit, and the benefits derived-from this control.No. 12 Cu-Pb Flotation: The complex nature of the Brunswick flotation process has been described else-where. 1,2,3 Four final concentrates are eventually produced, these being a Zn concentrate assaying 53% Zn, a 30% Pb concentrate, a 20% Cu concentrate, and a bulk Pb Zn concentrate assaying 35% Zn and 17% Pb. The Cu concentate, Pb concentrate, and bulk Pb Zn concentrate are all derived from a primary CuPb concentrate assaying 26% Pb, 11% Zn and 1.8% Cu.The No. 12 CuPb circuit produces approximately two thirds of the total primary CuPb concentrate. No. 12 ore, assaying 3.5% Pb, 9% Zn, 0.25% Cu and 100 g/tne silver, is ground in two parallel grinding circuits. Each line uses a 3.2 x 4.2 meter rod mill in closed circuit with two parallel 3.2 x 3.9 meter ball mills. Ball mill and rod mill discharges are classified in two stages of cycloning. The secondary cyclone overflow, or flotation feed, is controlled at 65% passing 37 microns."

Jan 1, 1981

By Chuan-Jian Zhong

Gold-based nanoparticles in the size range of a few nm have attracted increasing interests in catalysis, sensors and biomedical applications. The study of the unique catalytic properties of nanosized gold was inspired by the pioneering work of Haruta on the nanogold-catalyzed CO oxidation (1-4). There have been a number of excellent reports discussing both fundamental and application aspects of gold nanoparticles in catalysis (3-8). Our work reported herein is aimed at investigating the preparation and application of gold and its alloy nanoparticles for potential applications in fuel cell catalysis. Fuel cells operating by electrochemical oxidation of hydrogen or methanol fuels at the anode and reduction of oxygen at the cathode are attractive power sources due to their high conversion efficiencies, low pollution, lightweight and high power density. While methanol offers the advantage of easy storage and transportation in comparison with hydrogen fuel cell, its energy density (~2000 Wh/kg) and operating cell voltage (0.4 V) are much lower than the theoretical energy density (~6000 Wh/kg) and the thermodynamic potential (~1.2 V). The poor activity of the anode catalysts and inefficient activity or issue related to "methanol cross-over" at the cathode electrode are associated with the loss of about one-third of the available energy at the cathode and the other one-third at the anode. Extensive studies have been focused on Pt-group metals (Pt+Pd+Rh+Ru+Ir (PGM)) for both anode and cathode catalysts. A major problem is the poisoning of Pt by COlike intermediate species (9,10). Recently, oxide-supported gold nanoparticles in the <10 nm size range have emerged as one of the best catalysts for CO oxidation (1-3,11), and for water gas shift reaction in reforming stage using 5 nm Au on Fe2O3 (6). Gold and its alloy with other metals in the nanosize range present new alternatives (2,12). Whether the unique properties of gold nanoparticles can be exploited for addressing these problems is a focus area of our work. The ability to harness the large surface area-to-volume ratios and the unique surface sites of nanoparticles in <10 nm size range, especially in heterogeneous catalysis, constitutes a major driving force in fundamental research and practical applications of nanoparticle catalysts. It is this size range over which the metal particles undergo a transition from atomic to metallic properties. The understanding of factors controlling the morphological and surface reconstitution associated with such a size range is of fundamental importance to the ultimate exploration of nanostructured catalysts. We have been investigating the interfacial structures and properties of core-shell types of nanoparticles consisting of gold or alloy nanocrystal cores and organic monolayer shells that were prepared by twophase synthesis (13) and processing (14) protocols. Important attributes of such nanoparticles include controllable size monodispersity, processibility, and stability towards size- and composition-tunable catalysis (15-21). Some of these attributes were studied for understanding their electrocatalytic properties in the oxidation of methanol and reduction of oxygen, which are of fundamental interest to fuel cell technology.

Oct 1, 2003

By S. Noh, T. K. Kim, B. O. Lee

Future nuclear reactor systems such as a sodium-cooled fast reactor are being designed under severe conditions in terms of operating temperature and irradiation fluence compared to current commercial reactors. For realization of such systems, it is necessary to develop an advanced structural material having both high strength and irradiation resistance at high temperatures. Oxide dispersion strengthened (ODS) steel is considered as one of the most promising structural material because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density. Up to now, ODS steels have been intensively studied and developed to apply these materials to the in-core structural component of future nuclear systems. Several advanced ODS steels were designed and fabricated by a mechanical alloying, hot isostatic pressing and hot extrusion processes. This study focuses on the effects of heat treatment parameters during the fabrication process parameters on the microstructures of ODS steels for future nuclear system applications.

Jan 1, 2015

By B. R. Hart, S. S. Dimov, J. Fournier

Carbonaceous matter (c-matter) in sulphide ores can adversely affect the process of gold recovery during cyanidation due to its ability to adsorb, or preg-rob, gold from a cyanide leach solution. This paper describes a standardized procedure for characterization of c-matter in an ore sample providing detailed information on its composition, maturity and preg-robbing capacity. The procedure utilizes the following complementary analytical techniques in conjunction with several chemical tests and assays: SEM/EDX Raman spectroscopy and TOF-SIMS. Results of the test can be used as a predictive tool to estimate the impact the c-matter will have on the gold recovery process. A comparison between predicted preg-robbing behaviour and cyanidation test results are presented.

Jan 1, 2011

By H. D. Goodfellow, R. A. Elliott

"This paper covers the evolution of large mills and autogenous grinding and compares grinding practice in the iron ore industry with that in the base metal industries. Comments on novel methods of grinding are presented for discussion. Recent developments in the field of classification are briefly reviewed. A systems analysis approach to grinding circuits is discussed. Finally, a point is made for establishing a group within the industry with the purpose of developing a comprehensive evaluation of grinding research and development."

Jan 1, 1971

By W. J. Tough

THIS paper offers examples of some of the typical calculations which occur in the ventilation of metal mines. The fi.rst section of the paper discusses the problems associated with natural-draft pressure; the second section presents the more common of the calculations concerned with the operation of mine fans; the third section illustrates the integration of the individual problems covered by the preceding sections into the larger problem of determining the operating characteristics of a fan for a particular mine duty. There is a very definite limit to the extent to which pure arithmetic can be successfully applied to the solution of min<; ventilation problems. As mines advance from the exploration, development, and initial production stage to the rime when underground workings become exceedingly complex, there is a considerable increase in the relative importance o theory and judgment in the solution of ventilation problems. These calculations illustrate the application of mathematics to ventilation, but they also in-elude examples of instances where arithmetic cannot be conveniently applied, and important estimates, based on judgment compounded of experience and a knowledge of the theoretical consideration involved, must be made. The inclusion of such estimates is intended as a guide and a warning to the reader; a guide in assisting him to recognize and estimate his own incalculables; and a warning that the solutions must not be blindly applied to his apparently similar problems. These sample calculations are intended to assist the reader in applying the theory contained in the standard texts on metal-mine ventilation. They have been selected from the ventilation experience of a British Columbia mine.

Jan 1, 1942

By Euler De Souza, J. Daniel Stinnette, Julian Varaschin

"This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and of electric equipment and examines how they can be applied in determining reasonable ventilation rates for Tier IV compliant diesel equipment and for electric equipment operating in mining environments. Airflow calculations for modern diesel-powered equipment and for electric equipment are more complex and must be based on a combination of factors that are unique to each mine. Methodologies for ventilation rate determinations for each case are proposed in this paper.INTRODUCTIONTraditionally, airflow requirements for production and support equipment operating in underground mines have been determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations or determined empirically from known quantities. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is still a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. The question remains, what ventilation rates should the ventilation system designer apply for modern diesel equipment?Also, given the ongoing development of grid/battery-electric equipment and active construction of fully electric mines, it has become critical to determine adequate airflow rates per brake kilowatt of electric engine power. One of the most important criteria for determining ventilation rates for electric equipment is the amount of heat they generate, as this is the most significant emission produced by electric equipment (which do not produce exhaust gases or particulates). Therefore, ventilation rates required to dissipate heat from electric equipment must be suitably determined for all electric vehicle fleets operating in underground mines."

Jan 1, 2019

By Mark Holdsworth

In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart.

Jan 1, 2012

By Andrukaitis. E.

The increasing use of electronic equipment by the Canadian Forces has increased the importance of electric power. A power source that is packed with energy and yet light, small and durable is the common request of military users. However, this needs to be achieved while also addressing the requirements of safety, reliability and low temperature performance. The potential use of fuel cells in a military environment has become a possibility in several areas in the 21st century. Some examples of power source requirements and the materials related R&D required to give better, higher energy power systems in the future will be discussed.

Jan 1, 2005

By G M. Young

IT IS most appropriate that this first Memorial Lecture should be given in the Province of Quebec, near the site of the first metallurgical industry in Canada. At La Forge, about seven miles north of Three Rivers, iron was produced in 1783. We are told that the early settlers obtained most of their iron-ware -stoves, kettles, axes and ploughshares -from this smelter, with its foundry and forge. The Canadian copper industry also had its beginnings in Quebec when, nearly 100 years later, in the 1880&apos;s, several small copper smelters were erected in the Eastern Townships. Later, in 1899, Canada&apos;s first aluminum smelter was built at Shawinigan. From these small beginnings has grown a vast metals industry, the export value of its products being only exceeded by that of our forest products -newsprint, pulp-wood and lumber. As we are not a large country in terms of population, our domestic capacity to consume is often small in relation to our developed capacity to produce.

Jan 1, 1963