Search Documents

The phosphorus content of the banded iron formation (BIF) and of the associated iron ore deposits in the north west of Western Australia is known to vary widely, a fact which has considerable econ~mic significance. Trendall and Blockley (1970) have described the variety of textural appearances of apatite in the Hamersley Group BlF, and suggest that apatite may account for the entire phosphorus content of the unaltered BIF.A preliminary investigation using an M.A.C. electron microprobe analyser has shown that, at least in some iron ores and in partially enriched BIF and associated shales, the phosphorus occurrence is more complicated than this. A suite of samples was examined from one location which covered the entire Dales Gorge Member and some adjoining macrobands in the Mt. McRae shale, together with samples selected for their high phosphorus content, degree of ore enrichment, and position relative to the enrichment zone. Calcium apatite was not observed in any sample of ore from this sequence, despite its ubiquitous occurrence in the BIF. Silicate mineralogy in the enriched regions also differs from that in the BIF, but this change has not yet been studied in detail.The phosphorus content of goethite in one orebody is often high and appears to be in solid solution in the goethite structure. It shows little or no variability on a micro-scale within a grain, except where theremay be a zoned enrichment near boundaries and solution channels. There is also a limited solubility of phosphorus in hematite (the maximum observed by the author is 0·1 per cent P); but where the hematite is martitic (after magnetite) its phosphorus content is always low or zero. In some bands, martitic hematite has been hydrated to goethite, and this also has a very low phosphorus content. Phosphorus was not found in the silica or silicates in the ore, and even when iron enrichment is just beginning, a limited suite of samples from the BIF suggests that the phosphorus content of the chert microbands is almost entirely in the microscopic goethite nuclei (after riebeckite) scattered throughout the chert. The ability of goethite and hematite to accept phosphorus...

Jan 1, 1973

By G Fahey, S Rose

"Mining geology as a defined profession is only about 100 years old. The successful modern mine geologist needs to be a multidisciplinarian, but also needs to maintain a focus on the key outputs of the role. The technical skills needed in the role have increased as mining methods move to increasingly mechanised techniques. As well as being the guardian of the orebody and ensuring minimal dilution to expected ore grades, the mine geologist should be competent in the 12-point mine geology process. The mine geology process should include:a statement of purpose (a ‘mission statement’)geological mapping/logging system that supports consistent and regular geological data collection, storage, and interpretationsampling system that can produce representative samples and fits in with the mining scheduleassay database with relevant controls to ensure only ‘clean’ data is loadedsimple quality assurance / quality control (QA/QC) system for samples and assays, with a response process to react to out of specification resultsconsistent method of exporting, visualising, processing and interpreting assay data to create mining blocksdevelopment sign-off system so that all development and stoping is controlledproduction tracking system to monitoring and reporting what ore and waste volumes have been moved from the face, to any intermediate stockpiles, the run-of-mine (ROM) pad and into the crusherreporting system for daily, weekly and monthly reporting of tonnes and gradesdocumentation so that the grade control system has simple, but effective descriptions of how it works, who has responsibilities, and authorities, and be easily maintainedreconciliation system to compare resource and reserve to grade control and to mined and milledtraining system so that the geology team can quickly become competent.In this paper, the authors discuss the requirements of each point, and comment on common shortfalls observed by them over several years’ experience on producing mines worldwide.CITATION:Rose, S and Fahey, G, 2014. Modern mining geology, in Proceedings Ninth International Mining Geology Conference 2014 , pp 461–466 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By F Farías, D Villa

Codelco’s Salvador Project has been operating a block/panel caving mine for more than 50 years. This underground mining method dynamically mixes the ore and dilution. As a result, forecasting grades is difficult and achieving 100 per cent extraction of the reserves is practically impossible. A substantial volume of the ore mixed with dilution becomes remnant ore and remains to be subsequently extracted.A potential open pit mine is under evaluation at Codelco’s Salvador Project, which includes the extraction of remnant ore post-block caving extraction. An effective methodology has been implemented to estimate what is left behind once the underground mine has closed. A new mixing method using the Cellular Automata (Alfaro and Saavedra, 2004) approach has been used to allow estimation of the remnant ore with a sufficient level of confidence to be included as part of the open pit reserve.A remnant block model is created using elements such as in situ block model, drawpoint layouts, historical production records and the drawpoint extraction. Using this information, simulations of the extraction of the mine by month from 1959 to 2019 were completed, using different mixing scenarios and trying to replicate the tonnage and grade extracted.Finally, the remnant block model is categorised using a score card with four inputs to assess the risk of the estimation of this material into a category class (measured, indicated and inferred).CITATION:Villa, D and Farías, F, 2016. Remnant ore model generation and categorisation post-block caving extraction at Salvador Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 461–470 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 km. Some 500 km south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 km. The Complex was emplaced at several centres along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite. Except in the lower units of the Ultramafic Series sulfide mineralisation is widespread. Pyrrhotite is the dominant sulfide with lesser chalcopyrite pentlandite and pyrite. Four significant zones of sulfide accumulation are recognised and discussed in some detail. Evidence suggests that the primary magma from which the Riwaka Complex was derived was sulfur deficient. It is concluded that the sulfur content of the Riwaka Complex was derived from assimilation of sulfur rich wall rocks during intrusive processes.

Jan 1, 1980

Industrial minerals and rocks are those which are economically important because of desirable physical and/or chemical properties rather than metal or energy content. The evaluation of these resources for investment purposes in general follows established procedures after due consideration of well documented input data. However, in view of the sensitivity of many industrial mineral projects to specific inputs they require very careful analysis. The characteristics of the industrial minerals and the industrial minerals industry are reviewed and the significance of logistics, customer requirements, technology and marketing are discussed. Implications in relation to resources/reserves terminology are considered with phosphate rock used as an example. It is concluded that industrial mineral projects as a consequence of technology and market dependence in particular can give a high level of investment risk. The industry, however, offers most interesting and challenging employment opportunities for geologists, mineral engineers and economists.

Jan 1, 1988

By S Lush, R Polglase

McConnell Dowell is pleased to be given the opportunity to present two papers to this conference. The first is a general discussion paper on our work in the field of slurry transportation. The second will be a technical paper on the development of a welded coupling compatible with urethane lined pipework. We trust that by discussing our recent work we can leave two lasting impressions on you: the versatility and useful role of slurry transportation, and the leading role taken by New Zealand in this technology This paper discusses three recent projects the New Zealand Steel Ironsand Transfer Line the Coarse Coal Ship Loading Technology the Nerang River Sand By-pass System. These have followed on from the other slurry projects with which McConnell Dowell has been associated such as the ironsand export trade at Waipipi and Taharoa. The New Zealand Contractors Federation awarded the Construction Award for 1986 to McConnell Dowell for the Ironsand Slurry Pipeline.

Jan 1, 1986

THE ore treated is almost pure copper pyrites (chalcopyrite) in a gangue of quartz and quartz-felsite. Very little free iron sulphide (pyrite) occurs, and at the time of the erection of the flotation plant the stopes in the oxidized zone had been almostentirely depleted. This zone only extends to a shallow depth, and, below the l00-ft. level, the sulphide for the most part is clean and bright but in the crushed and brecciated parts of the ore channel, where surface water has circulated freely, the gangue is decomposed and kaolinized, and the copper sulphide badly tarnished. This class of ore gave considerable trouble at the mill, but unfortunately, was very limited in quantity. A sample of rich ore assayed-Copper, 21.2 %; iron, 24:.3 %; silica, 28.9 %; sulphur, 25.1%.The concentration in the original mill was effected by handpicking, jigging, and tabling. A considerable portion of the copper mineral arrives at the surface in the form of large lumps of very pure quality, eminently suitable for sorting out by hand.The rich ore is tipped over a grizzly at the shaft bins; the oversize hand-picked, and the undersize bagged direct.

Jan 1, 1912

By W C. Cook, S J. Mathews, A H. Purvis

The Golden Cross Gold Mine is located at the head of the Waite kauri Ri ver, 8 km northwest of Waihi near the southern end of the Coromandel Range. The mine produces gold and silver from epithermal veins hosted by Miocene andesitic flows and pyroclastics of the Coromandel Group. Golden Cross is owned in joint venture by Coeur Gold NZ Ltd (80 per cent) and Viking Mining Company Ltd (20 per cent). Mining is by open pit and underground methods. Mineralisation in a near-surface sheeted/stockworked vein zone is mined from the open pit. The deeper Empire Vein System is mined from underground where higher grade mineralisation is restricted to generally discrete veins. The open pit stockwork zone is west of and offset from the updip trend of the Empire Vein System. The Empire (hangingwall) Vein strikes generally north-northeast and dips steeply west. Dips become subvertical at greater depth. The hangingwall vein is a well developed, generally continuous structure with relatively high gold grades. A complex footwall vein system forms shallow west-dipping offshoots to the hangingwall vein. Structure and gold grades become increasingly erratic away from the hangingwall vein. The better developed footwall veins carry economic grades and high 'spot' grades over 50 g/t Au are not uncommon. Highest gold grades are associated with tightly crustiform banded sections of quartz veins and with dark fine grained siliceous breccias. The main hangingwall vein occupies a major north-northeast trending fault structure, the Empire Fault. Footwall veining forms within subordinate splinter fault zones. There has been extensive multidirectional pre-, syn- and post-mineralisation faulting. Fault manifestation is highly dependent on host rock characteristics. The central part of the hangingwall vein and surrounding silicified country rock has been shattered by a major fault structure, the West Mine Fault, forming a poorly consolidated, blocky quartz-breccia ore zone. Away from the more brittle ore zones and associated silicified envelope, wide clay-filled shears mark the major fault trends. Development of the deposit is considered to have occurred in two distinct stages related to separate episodes of dilational jog movement on the Empire Fault. The first phase reactivated the pre-existing Empire Fault as a dilational fissure with subordinate splinters on the footwall side. The Empire Vein System (hangingwall and associated footwall veining) formed during this phase. A second phase of renewed movement with further dilation resulted in more extensive fracturing of the Empire Vein and surrounding country rock and formed the sheeted/stockwork veining of the open pit. An upwards/westward migration of the hydrothermal system is assumed but fluid pathways between underground and open pit veining are unclear. Ore extraction and mining geology methods have responded to improved understanding of the grade and structural variability, and changing ground conditions inherent in the vein system. The underground mine produces ore from flatback cut and fill, post-pillar and bench stopes. Open pit and underground ores are campaign milled through a conventional CIP plant.

Jan 1, 1993

By C Roche, G M. Mudd

The Morobe Province of central Papua New Guinea (PNG) has been mined for gold for nearly a century, although it is only in the past decade that large-scale modern mining commenced. The Hidden Valley gold-silver project began construction in mid-2006 and production by August 2009, and is located in the mountains above Wau in the headwaters of the Watut River. The mine is owned and operated by the Morobe Mining Joint Venture (MMJV), which also owns the Wafi-Golpu project, comprising the Wafi gold deposit and Golpu copper-gold deposit, situated in the Watut River Valley. Together they represent a potential mine of the scale of Ok Tedi or Bougainville or bigger. The MMJV is owned in equal shares by Newcrest Mining from Australia and Harmony Gold from South Africa. Although Hidden Valley was the first large-scale mine in PNG to engineer and build a tailings storage facility, poor environmental management during construction and early operations led to significant erosion of waste rock and sedimentation impacts throughout the ~200 km length of the Watut River. Since then, substantial efforts have been made to improve environmental management, especially waste rock placement and storage and water quality management. While the impacts from the Hidden Valley project appear to be reducing, the saga has heightened concerns by many along the Watut River and across PNG about ongoing impacts from mining.This paper presents the results of an ongoing project in the Morobe Province conducted by the Mineral Policy Institute examining the historical, current and future impacts of mining, including community views, social and environmental impacts and the monitoring and regulation of mining. Overall, there is a clear need to more fully integrate social and environmental issues into life-of-mine planning and go above and beyond regulatory requirements. In this way, some of the lessons learnt – by the community, MMJV and government – can be incorporated before, during and long after mining.CITATION:Mudd, G M and Roche, C, ?2014. Mining in Morobe, Papua New Guinea – impacts, assurance and self-determination, in Proceedings Life-of-Mine 2014 , pp 313–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

Leading Article from "British Medical Journal," London, 4th, November, 1944.Assuming that silica exerts its injurious effect upon animal tissue through a slow transformation into silicic acid, Denny, Robson, and Irwin thought that if the solubility of siliceous material retained in the lungs could be suffciently reduced the usual fibrotic response could be diminished or prevented. They discovered that aluminum powder rendered siliceous material insoluble in vitro by coating the silica particle with a thin film of gelatinous hydrated alumina, which on drying formed crystalline alpha aluminum monohydrate. The presence of this adsorbed layer on the surface of the quartz was shown by staining it with aurin. That metallic aluminum dust produced no fibrosis in the lungs was demonstrated by dust-inhalation experiments on eight rabbits. Attempts were therefore made to prevent silicosis by mixing quartz with metallic aluminum dust.Animals exposed to quartz dust developed typical silicosis in about five months, but the addition of 1 per cent. aluminum powder prevented this even after exposure had been lengthened up to 22 months, provided the aluminum powder was of a particle size below 5. This year Crombie, Blaisdell and MacPherson have reported the treatment of 34 silicotic miners by the daily inhalation of fine aluminum powder freshly ground from small aluminum pellets in a specially constructed mill. Daily treatment began with five-minute inhalations, which were gradually increased to 30 minutes. Some of the men received 300 treatments, but the majority only 200. Out of the 34 cases thus treated clinical improvement was manifested by lessening or disappearance of shortness of breath, of cough, of pain in the chest, and of fatigue. In 15 cases the condition became stationary and remained so in spite of continuous employment in silica dust throughout the treatment. The progress of the disease was assessed by means of tests for respiratory function repeated at three-monthly intervals. Obviously this treatment cannot be regarded as a cure for silicosis, since it cannot restore lung tissue which has undergone fibrotic change; but Crombie and his colleagues believe that the inhalation of finely particulate aluminum powder offers every prospect of preventing the development of human silicosis.In view of these findings, it is surprising that repeated papers by Goralewski from Germany describe various types of lung disease attributed to aluminum dust, and press for them to be scheduled under the Workmen's Compensation Act in that country. Seven hundred workers were investigated. They were making, probably by a stamping process, aluminium powder containing about four milliards of particles of dust per grain, and are reported as complaining of dry cough with pain on breathing, shortness of breath, poor appetite, and gnawing abdominal pain. Spontaneous pneumothorax developed in four workers. No abnormal physical...

Jan 1, 1945

Statistics on the imports of industrial minerals into the EECshow that the traded volume in 1987 is approximately 23 million tonnes.The following table documents the imported quantities on the most important industrial minerals.

Jan 1, 1989

The use of walk-through inspections, approvals and ad hoc investigations to ensure risk is kept within acceptable levels is reaching its limits of effectiveness. Further improvement in occupational health and safety requires a systems approach, and the use of Quality Management principles is an obvious basis for this. SafeGuard, a æbest practiceÆ model health and safety management system and audit criteria based on AS/NZS ISO 9001:1994, has been produced by the Department of Mines and Energy. Quality style audits of mine and quarry health and safety systems are now being carried out by the Inspectorate.

Jan 1, 1998

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

In the Bendigo district, with its large number of comparitively small leases worked by separate companies, we might naturally expect to find many different arrangements of winding machinery and, as a matter of fact, there are steam winches, old portable engines, single and duplex geared engines, twin engines on the first motion, and in one instance a single engine on the first motion, all employed for hauling purposes from depths of 1000 feet and over.It would be impossible in the compass of this paper to discuss at all fully the various arrangements of winding gear employed on the field the writer can simply refer to some of the more prominent features, in the hope that the information may prove of interest and benefit to the mining community. In criticising our machinery it must be remembered that when many of the plants in use at the present time were erected, they were not intended to wind from more than one third of the depths now common on the field; but so long as the machine could be made to haul a tank of water from the bottom of the shaft it has remained, the greater power required being obtained by increasing the piston speed and altering the gear wheels to suit. The consequence is, of course, that in some of our mines the speed of winding is painfully slow this feature, however, though certainly not consistent with modern ideas of economical mining, does not so seriously affect Bendigo as it would other fields, for the comparatively small quantity of stone to be raised from a given reef by some...

Jan 1, 1902

On the Role of Dixanthogen in Froth Flotation

Sep 13, 2010

In choosing such a threadbare subject for a paper I fear that I may in some measure be taxing your patience, yet as upon the accuracy with which the work is done depends the result of conclusions drawn as to whether a property will be profitable to work or otherwise. The subject cannot be too well threshed out, and I trust that upon certain points that have come within my own experience I may be able to give 'hints that will prevent others from making mistakes. First as to alluvial. Gold is often found from the grass roots down, often ill particular horizontal bands in the wash, but more generally concentrated either on a true or false bottom. When sampling dry ground for proposed hydraulicing I have obtained accurate results only by taking the whole of the dirt from measured shafts, stacking it as it was lifted on a tarpaulin, and putting the whole quantity through a carefully constructed box. In wet ground careful borings will in most cases give fairly correct results, but where it is possible to sink shafts, that should be done, as a guide is then also obtained as to the nature of the wash, whether it is bouldery, cemented, or free. Sampling in a face is a more difficult work in many respects than in new ground, as so many elements enter into action to spoil accurate sampling. Of course the great thing to avoid is sampling in any place where either natural or artificial concentration has taken place, and very much has to be left to circumstance and the sampler's own judgment. In passing I may mention that I have on several occasions seen diggers deceive themselves in wet ground where they were sinking and coping as best they might with water. They would take a dish of dirt from the bottom of their hole, pan it off, and take the result as a fair yield, and on the strength of it perhaps spend a lot of time and money in tail races and whereas in their sample there had been a process of concentration carried on, the movement and working in the water had caused the gold to work down, and anything like accurate estimations by the method pursued were out of the question.

By C Maloloy-on, S Morgan, M Deiparine, H Mackie

There is a strong focus in the mining industry to limit its impact on water quality and usage. This is even more evident in developing countries, where mining companies operate within local communities and have to be diligent not to affect them negatively. In mineral processing operations, the vast majority of water reclamation occurs at the tailings thickener area and tailings storage dam. It is often more effective to maximise water recovery at the tailings thickener before material transport to the tailings dam. Tailing dams are relatively inefficient, and experience a high degree of water loss due to evaporation, seepage and water retention. In addition, tailings dams present the biggest environmental liability for mineral resource projects, so it is beneficial to limit their size and loading.In the past, it was common for tailings thickener areas to have a significant footprint with several large diameter conventional thickeners, producing underflows of between 45-55% solids (w/w). At times, these multiple thickeners were difficult to operate, leading to inefficiencies in water recovery and quality. The development of High-Rate Thickeners (HRT) has resulted in improved settling properties and HRTs usually operate at significantly higher solids loadings (= 1.2 t/m2.h) when compared to conventional thickeners (= 0.1 t/m2.h). Subsequently, thickener diameters have reduced in size and HRT technology has become the preferred option for thickener circuit design in both new and existing operations. HRTs also produce higher water recoveries with increased underflow densities = 55% solids (w/w).The Carmen Copper Corporation (“Carmen Copper”) circuit upgrade is a recent example of these HRT benefits, where one, 39 m diameter, Outotec HRT treats the solids flow rate of five 76 m diameter conventional thickeners. This has allowed operations to increase dry plant tonnage by 50%, maintain key performance targets and provide a framework for further plant expansion. This paper details the sustainable approach to the Carmen Copper tailings thickener upgrade, where metallurgical performance, cost-effectiveness and environmental impact were key considerations.CITATION:Morgan, S, Mackie, H, Maloloy-on, C and Deiparine, M, 2015. Carmen Copper – a sustainable approach to tailings thickener upgrades, in Proceedings MetPlant 2015, pp 416–430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Computer applications are ideally suited to the day to day operations of grade control and short term planning on a mine site. By refining this part of the operation there is scope to increase profits by more accurately predicting ore grade and tonnage, and allowing the mining engineer more flexibility in his approach to scheduling. Large numbers of blasthole or ditchwitch samples need to be processed in a fast and efficient manner, and stored in a database for future reference. The mining engineer has to calculate tonnages and subdivide the blast or digging area into mineable areas of waste, low and high grade ore. New grade and tonnage information must be used by the mining engineer to update his short term plan. Answers must be obtained quickly and efficiently, but a high level of individual input is necessary in order that maximum use is made of the information. Geostatistical analysis of samples can be used to refine the interpolation techniques. Reconciliation between the original grade model, the newly sampled area, and the final product should be monitored continually.

Jan 1, 1989

By Wingham D. W

Based upon the previous work of Norman & Loeb, a method was used to assess the comparative wearing properties of ten different alloys being used, or being considered for use, as mill liners and grinding media at Mount Isa, The materials to be tested were obtained in the form of large diameter balls, and were run, along with the regular ball charge, in a large ball mill operating under normal grinding conditions. At selected intervals, the test balls were removed from the mill, weighed and identified, and their relative wear rates determined.INTRODUCTIONInformation in metallurgical journals, from local iron and steel foundries, and from various metal promotional organizations has suggested that the various alloy compositions available should be examined and assessed for possible use as milllfners and grinding media.Previous attempts at evaluation of recommended materials for these applications elsewhere, have usually involved the purchase of large quantities of grinding balls or complete mill liner sets, requiring running periods of up to two years or more. As well as being both a costly and lengthy procedure, the information obtained may be of little significance, due to changes in milling practice, and ore characteristics during the period of operation.To overcome these difficuities, a method was adopted based on the short time wear rate test recommended by Norman & Loeb (1949) and Norman (1957) in which all the materialsunder consideration are ·subjected·concurrently to the conditions of service.Previous calculations of wear rates have been dependent1. Senior Metallurgist (Materials), Mount Isa Mines Limited.2. Metallographer, Mount Isa Mines Limited.Manuscript received at The Institute, 22nd April, 1963, and presented to the1963 Annual Conference.

Jan 1, 1963

By D Craw

Previous studies of alluvial gold in Otago and Southland placer deposits have suggested a gold-mercury association for some deposits derived from Caples Terrane schist, whereas alluvial deposits on Torlesse Terrane basement typically have no mercury. A regional study of gold from Otago Schist vein deposits from both Caples and Torlesse Terranes has revealed the presence of both Au-Ag and Au-Ag-Hg alloys in both terranes. Au-Ag alloy (3 - 4 wt per cent Ag) is typical for gold found in most Torlesse vein deposits, and Au-Ag-Hg alloy (3 - 8 wt per cent Ag, 2 - 8 wt per cent Hg) is found in many Caples vein deposits. Au-Ag-Hg alloys are not exclusive to the Caples Terrane, however, as Au-Ag-Hg alloys with up to 4 wt per cent Hg are found in vein material from the Torlesse-hosted, HydeMacraes Shear Zone. In addition, not all Caples-hosted deposits have a gold-mercury association; gold grains from the Carrick and Invincible gold fields have no detectable mercury. The present study characterises gold compositions from various hard-rock vein deposits and has potential for determining placer-source relationships.

Jan 1, 2003