Search Documents

By Lewis J. W

The mineral sand orebodies of the east coast of Australia occupy approximately three per cent of the dune-heath-wetland coastal environment. They are associated with coastal plant communities ranging from Holocene high dunes carrying mature Eucalypt forests to low- lying heaths on Pleistocene deposits. Commonly, 0.25 to 1.5 per cent of the sand volume mined is removed from the site. Therefore, the volume change is insignificant. The equipment and techniques in use are flexible and the land can be returned in a manner suited to its subsequent use for grazing, subdivision or recreation. Landforms similar to the pre-existing are created in two case studies given. Sophisticated revegetation techniques are practised and are discussed in two case studies. Pre-mining vegetation surveys and post-mining monitoring are used to guide the management of the ecosystem.

Jan 1, 1976

The Ida Valley in Central Otago is one of series of parallel basins filled with freshwater sediments. The basins are in fact tectonic depressions superimposed on NE trending grabenlike structures which occur in the area and are the result of block faulting possibly initiated in Cretaceous times and concluded in late Tertiary and early Quaternary. In Central Otago this tectonic event affected metamorphosed rocks belonging to the eastern facies of the New Zealand Geosyncline and collectively known as the Haast Schist Group. These rocks constitute the basement and the shoulders of the tectonic depressions. The Ida Valley occupies the depression wedged in between the Raggedy Range to the NW and the North Rough Ridge in the SE. The valley is approximately 38 km long, 3 to 7.5 km wide and is drained by the NE flowing Pool Burn, which meets the SW flowing Ida Burn. The resulting unified stream flows into the Manuherikia river which drains the next door depression to the NW. The present work deals with the Ida Valley basin and more specifically with the geology studied within two Prospecting Licence areas held by Gold Mines of NZ Ltd on the southeastern flank of the valley.

Jan 1, 1977

The cost of production from truck and loader fleets is influenced by management development of the culture of the organisation, work practices, systems and procedures of the production and maintenance teams. Establishing if the cost of production is the best that can be achieved then requires the measurement of results against established standards of performance. This paper provides a series of discussion points of the factors that influence the cost of production from men and machines for large scale open pit mining operation and provides some suggested performance standards in the form of Benchmarks. Most of the references have been drawn from established large scale deep pit mines in USA, Canada and Australia which have had to implement and constantly fine tune cost efficiencies in order to survive. The discussion provides:ò a review of priorities or the relative importance of the various cost elements for a mining system;ò suggestions of systems and procedures for the operation and maintenance of machines which are considered to yield the best overall results;ò examples of operations that have developed and implemented management systems and controls that are achieving good results in specific functions; andò suggested benchmarks of performance.

Jan 1, 1992

By Hossaini SMF

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Ramamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris: 611=1+B(63)O.825 acm 6cm where a1= axial compressive stress at failure, MPa; a3 = confining pressure, MPa; acm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (aim ) -0.185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By G J. Corbett

Magmatic-related low sulfidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system.   Low sulphidation systems in the south-west Pacific region exhibit a vertical zonation in deposit types: from porphyry copper-gold at deep levels, quartz-sulfide-gold at mesothermal to deep epithermal levels, carbonate-base metal gold at mainly epithermal levels, and epithermal quartz silver-gold at shallow levels. It is interpreted that the characteristics of each of these styles of deposits is produced by mixing with circulating waters of different physio-chemical compositions.

Jan 1, 1995

By Whiten W. J

The control of mineral processing plants incorporates a number of off-line and on-line actions by plant personnel to obtain satisfactory plant performance. In general, off-line actions centre around intensive data analysis, while on-line activities are either automated control actions or prompted by qualitative interpretations of quantitative and qualitative information. Data sets obtained by various data logging devices and laboratory analysis of samples in many modem plants may be very large and are often unmanageable. This paper presents a method of analysing the data sets typically found in mineral processing, based on cluster analysis. The results of this analysis leads to a more complete understanding of operations in comparison with existing analysis tools used in mineral processing.Improved process configuration, optimised control strategies and in some cases, direct use of the results in monitoring process unit operations may be achieved.

Jan 1, 1992

The products of the steel tube industry play an important part in the production,' transrzission and refining of oil. Steel tube manufacturing is already well established in Australia and supplies the petroleum industry with its requirements" within the .present limitations of the various tube plants., With the discovery of oil in commercial quantities in this country, the steel tube industry could be expected to extend its scope to cover a much wider range; of oil country tubular goods, line pipe and refinery. Tubing.

Jan 1, 1962

By Richards AB

This paper describes the ENVIB software system, which has been developed in a menu-driven form to aid in the monitoring and assess- ment of vibration caused by routine blasting operations and for research and development projects. The paper gives an outline of the capabilities of the system by means of screen-dumps and a general descriptive commentary. Technical notes have been added where appropriate to further describe the system. The ENVIB system covers: I . Analysis of blast vibration results, and preparation of graphs and tables for control and estimation purposes. 2. Effects of atmospheric conditions and air vibration propagation. 3. Real-time acquisition and analysis of analogue blast vibration sig- nals directly from transducer equipment or from FM tapes. 4. Analysis of digital files on floppy disc or transferred via the serial port from blast monitoring equipment. 5. Transfer function calculation for structure response studies.

Jan 1, 1988

By Royston, Woods R

ANI Bradken Vortex Pulp Lifters and Grates, both as original equipment and retrofitted to existing SAG mills, are now in field operation. The development of the Vortex leading curve pulp lifter was based on an analysis of traditional radia

Jan 1, 1997

By Bruce P, Luyendyk

The South Island of New Zealand comprises a collage of distinct tectonostratigraphic terranes. Some tectonic models predict that these terranes formed on or near the margin of Gondwanaland. However, geologic evidence suggests that some of these terranes may be exotic. Over 400 samples from 30 sites were collected from the Brookstreet terrane within the Takitimu Mountains. The section includes the early Permian Takitimu Group and the late Permian White Hill Intrusive Suite. Over 80% of the rocks show a partial or complete regnetization in the present field due to recent acquistion of VRM. Although some remagnetization of the Takitimu Group occurred during the emplacement of the White Hill Intrusives, both early and late Permian direction have been isolated. These directions indicate a mid-latitude origin for the Brookstreet terrane, and suggest a strong clockwise rotation between early and late Permian time. A published paleomagnetic result from the younger, but related, Murihiku terrane suggests that the Brookstreet terrane was sutured to the margin of Gondwanaland by the late Triassic, or that the Brookstreet and Murihiku are two distinct terranes.

Jan 1, 1987

By Little T. N, Bettess D

For many mining operations the challenge of equalling World Best Practices has become the key motivator for increasing mine productivities and for lowering total costs. In most instances this will only be achieved if mines optimise their total system rather than minimising specific costs within unit operations. In the past, drilling and blasting have been viewed as a cost to be minimised rather than operations which should have their impacts fully leveraged. Once a hardrock orebody is defined the activity which has the most substantial impact in determining the efficiency of a mining operation is the blasting. The output from a blast affects every downstream operation; only by understanding the extent and interactions can the mine be optimised. Substantial improvements to hardrock mining, quarrying and excavation operations are achievable. Instead of seeking the regular one to three per cent improvements based on reduction of consumables, mine operators would be well advised to go for much bigger targets of ten to 30 per cent by fully leveraging the drill and blast operations.

Jan 1, 1995

By Hunter T. C

The wirebar furnacing and casting facility commissioned in 1970 at Copper Refineries Pty. Ltd. (CRL), Townsville, comprising a 70 tonne/ hour ASARCO shaft furnace and a Walker type casting wheel, contained several unique design features. Since commissioning, effort has been directed at improving metallurgical control of the casting process. This has resulted in the identification of optimum mould lubricant properties and the use of continuous on-line measurement of molten metal oxygen content. Casting defects such as cracks and surface porosity are readily explained and controlled using these techniques.

Jan 1, 1977

By Reid T. W

This paper describes the results of investigations into the relationship between specific gravity and chemical composition in the Cockatoo Island orebody, In the early investigations the samples were classified into groups according to porosity. This resulted in high, medium and low porosity groups, the latter being further subdivided into ore and waste. Whole number tonnage factors were assigned to each group. In the later investigations the reciprocals of bulk specific gravity and true specific gravity were ex- pressed as linear combinations of iron, silica and alumina using stepwise regression. The efficiency of the models as predictors was tested by dividing the data into two sets; one of which was used to calculate the regression equation and the other to test the efficiency of the equation as

Jan 1, 1976

The South Mine, property of Broken Hill South Limited, is situated at Broken Hill, NSW, Australia, towards the southern end of the main lode. The leases (MLs 7 and 8) cover a length of 2400 feet along the lode outcrop and the workings extend, at this date, to a depth of 1940 feet below the collar of the original main shaft and to 825 feet below sea level. Mining operations have been continuous for about 58 years and during this period nearly 12.5 million tons of ore have been mined. The monthly tonnage extracted approximates 30 000 tons in normal times.The ore is a mixed sulphide containing galena and marmatite; the gangue minerals are principally calcite, rhodonite, quartz and garnet. A typical assay for a monthly period is 14.4 per cent Ph, 5.6 ozs Ag, and 11.6 per cent Zn. The whole of the ore is concentrated on the property by combined gravity and flotation methods. The lead and zinc concentrates produced are railed to other centres for the extraction of the contained metals.

Jan 1, 1994

By Holla L

There exist several legislative provisions in N.S.W. which work together to control surface subsidence due to extraction of coal by underground methods. The important ones are the Coal Mining Act, Coal Mines Regulation Act, Mine Subsidence Compensation Act and Dams Safety Act. In addition, there are guidelines laid down by the Chief Inspector of Coal Mines for mining under and in the vicinity of tidal waters and the ocean. There are also conditions of coal mining leases and conditions of approvals given to undertake various methods of mining which stipulate further controls. The legislative provisions and relative controls are designed to minimise surface damage, ensure safety , of major public utilities, control- surface land use and compensate damage caused by subsidence as a result of coal mining operations. They aim at balanced and responsible development of our valuable coal resources consistent with adequate safeguards to surface improvements and natural features. The paper discusses in detail these legislative provisions and the mechanics of their operation with a view to emphasising the fact that underground coal mining operations are undertaken responsibly and in a planned and rational manner for the overall benefit of the community. Further, the paper aims to demonstrate the need for legislative measures and conditioning of mining operations to keep abreast of developments in the knowledge and skills of mining and subsidence engineers and continuing improvements in mining technologies. Likewise there is a need on the part of engineers and those associated with introduction of new technologies to appreciate the requirements and existence of legislative and other measures having a direct or indirect association with surface subsidence as a result of coal mining operation.

Jan 1, 1986

The stratigraphy of the Singleton Coal Measures is reviewed and a revised stratigrapixy which has been ratified by the N.S.W. Standing Committee for Coalfield geology is nominated and defined by a selected type section. Withir the type section the occurrence of repetitive phases are illustrated and described. Coal. Measure units within the Singleton Coal Mean sures, termed the Wollombi and Wittingham Coal Measures respectively, are correlated with the Newcastle and Tomago Coal Measures. In formal nomenclature the Singleton Coal Measures are designated the Singleton Super Group. The major depositional cycles within the Coal Mea- sures are outlined together with those lesser phases within the Coal bearing sequences that influence the mining conditions likely to be encountered. Both tectonic and sedimentary features of the Singleton Coal Measures are considered and the localized post depositional effects on the coal seams and roof strata in- duced by differential, compactions are emphar Sized.

Jan 1, 1972

By Wilson AC

Permian coal from Western Australia's only producing coalfield at Collie is the dominant fuel used in generating electricity for the State's interconnected grid. Collie coal is sub-bituminous, non-coking and has a low ash, medium volatiles and high moisture content. The seams were laid down in a fluvial basin which extended beyond the Collie Basin and included the Wilga and Boyup Brook Basins at least. Adjacent parts of the southwest Yilgarn Block are prospective for Collie-type basins. In the past few years significant deposits have been delineated within the Perth Basin, specifically on the Vasse Shelf and in the Hill River area. In the former area high quality steaming coals are correlated with the lowest coal bearing member at Collie. The seams are amenable to underground mining and because of their high quality, the coal may have export potential. Sub-bituminous coal deposits of Jurassic age are present in the Hill River area. Exploration has down-graded the prospectivity of the Carnarvon and Canning Basins for sub-bituminous near-surface coal deposits. Tertiary lignite deposits are present in palaeo-drainage systems in the southern part of the State and their potential for development is being evaluated.

Jan 1, 1986

The major coalfields of Australia are almost unique in the occurrence in some areas of CO partly or almost completely replacing CH4,t1e normal seam gas from metamorphism of coal due to time and depth of burial. This CO2 situation has some benefits but mostly it introduces particular safety problems result- ing from the high density of CO2 relative to air, magnifying problems of gas dilution in ventilation, and the greater affinity which coal has for CO2 than for CH4 increasing proneness to gas-dynamic phenomena. The occurrence of most CO2 seam gas can be directly related to igneous intrusion and to its associated pneumatolytic injections. Whilst intrusions locally increase the rank of coal by their contact metamorphic effect, normal coal metamorphism due to time and depth of burial continues after intrusion and injection together with the ongoing metamorph- ic production of CH . This new CH slowly displaces any CO to leave some present-day intruded coals with seam gas with reduced CO2 or even without any significant CO2 associat- ions. The seam gas maps of the Bowen and Sydney Basins and more detailed maps of specific areas exemplify these situations. Mining progress, plus more searching studies of igneous-coal relationships provide improved understanding of the factors involved.

Jan 1, 1986

By Thatcher R

In areas where land suitable for development is a scarce resource, an upgraded post-mining land use can result in economic benefits to both the mining company and to the community.A study undertaken at Aberdare Colliery near Ipswich during 198611987 assessed the costs and benefits of developing the site following mining for grazing, forestry and residential uses. The proposed fmal land use plan comprised a combination of these uses that can be upgraded to higher valued uses once subsidence monitoring of backfilled open-cut areas and dumps indicates that total settlement has reached acceptable levels for development to proceed.The study involved the documentation of existing site environmental parameters and the delineation of site opportunities and constraints. The unpredictable nature of settlement over backfilled open-cuts and overburden dumps represents the major constraint to urban development on mined areas.

Jan 1, 1990

Safety bulletins and stickers issued for the paste backfill plant at Cannington read as follows: æCannington Paste Fill Plant, First of ItÆs Kind in AustraliaÆ. We could even dare to state that the Cannington plant is different than any other paste backfill plant in the world because of the overall design, plant equipment and underground delivery. However, one thing to be certain of is, the paste backfill plant works as designed and a pump is not required to deliver paste underground given the general plant arrangement at Cannington. The past two years have been a process of evolution to design and construct the plant and make it work. This paper will describe the paste process using full mill tails along with placement of cemented paste underground. Discussions will include rationale of fixed plant selection along with various control requirements. BHP World Minerals recently commissioned its paste backfill plant in December 1997. Cannington is placing full mill tails underground via two surface boreholes that deliver either to primary or secondary stopes.

Jan 1, 1998