Search Documents

By W Zhu, J H. Zhao, H Ma

The permeability coefficient is an essential parameter for the study of seepage flow in fractured rock mass. This paper discusses the feasibility and application value of using readily available RQD (rock quality index) data to estimate mine water inflow and grouting quantity. Firstly, the influence of different fracture frequencies on permeability in a unit area was explored by combining numerical simulation and experiment, and the relationship between fracture frequencies and pressure and flow velocity at the monitoring point in fractured rock mass was obtained. Then, the stochastic function generation program was used to establish the flow analysis model in fractured rock mass to explore the relationship between flow velocity, pressure and analyse the universal law between fracture frequency and permeability. The concepts of fracture width and connectivity are introduced to modify the permeability calculation formula and grouting formula. Finally, based on the on-site grouting water control case study, the rock mass quality index is used to estimate the mine water inflow and the grouting quantity. The results show that it is feasible to estimate the fracture frequency and then calculate the permeability coefficient by RQD. The relationship between fracture frequency and RQD and the relationship between structure surface frequency and permeability follow an exponential function. The calculation results are in good agreement with the field monitoring results, which verifies the rationality of the calculation method. The relationship between the rock mass RQD index and the rock mass permeability established in this paper can be used to invert the mechanical parameters of the rock mass or to evaluate the permeability and safety of the rock mass, which is of great significance to the prediction of mine water inflow and the safety evaluation of water inrush disaster management.

Nov 29, 2022

By Kajioka H, Nakamura Y

Na2CO3 is a powerful flux for both dephosphorization and desulphurization in oxidizing atmospheres. In order to study refining with Na2CO3 and the nature of the Na2CO3 slag itself, hot metal (4Kg) was melted in Al203 crucibles in a high frequency induction furnace and oxidised with oxygen under Na2CO3 slag. The behaviour of Na2CO3 at high temperature was observed by thermobalance. It was found that dephosphorization ceases in a few minutes and [,P] after refining is easily lowered to less than 0.010%. [%P] after refining is affected by [Si], [P] of hot metal, the refining temperature and the consumption of Na2CO3. Desulphurization also ceases in a few minutes but it shows curious behaviour, increase of [S], decrease of (S) and increase in sulphur lost, during the latter half of run. [%S] after refining is also affected by [P] of hot metal, the refining temperature and the consumption of Na2C03o

Jan 1, 1980

By Brathwaite RL

The gold-scheelite-quartz lodes of the Wakamarina valley were the most productive of the mesothermal gold-bear in the Marlborough Schist. Most of the production came from the Empire City and Golden Bar mines which worked tug, Golden Bar lode. Only 134 m of its 1800 m strike length are accessible, in the No. 2 level of the Golden Bar Mine. A fau I has downthrown the Golden Bar Mine section by 2 47 m and displaced it left-laterally by 18 m. The lode is a typical ribbon-banded mesothermal vein, averaging c. 1.75 m wide, and enclosing narrow horses of schist country rock. It i composed of bands of milky "buck" quartz with thin laminae of schist. Scheelite occurs in short strings of grains withi quartz on the footwall side of the lode and also in small quartz-carbonate veinlets in the foot wall and hanging wall schist The lode quartz contains only localised traces of pyrite and arsenopyrite. They are more abundant in the wall-rock schist.

Jan 1, 1995

By S Pollak, A Amon

This paper describes the current and finished design work which has been performed for shallow rock station caverns for New York CityÆs first new subway construction in 60 years. A new robust, sophisticated, design procedure has been developed for two up to 30 m wide caverns, with overburden of less then 12 m, and rock cover to span ratios (C/S) in the order of 0.25. The design is based on empirical input parameters like the Q-value, rock mass rating (RMR) values, rock mass class after Cording (1984), cover to span ratios, which have been validated by the use of structural computer models as well as two- and three-dimensional numerical discontinuum models. The design approach is a staged approach using first principles, empirical models and non-linear FEM and DEM models. In addition, the paper describes the factors and circumstances why shallow caverns have been selected instead of cut-and-cover structures and why all the underground station structures have been developed as drained structures.

Jan 1, 2008

IA )W cli',hla cn1cnt fault 7011(-s 0 11Cn cOrnprise a nrc,II of inrcIIinkc(I faults, cvtcnqonal shear and In]rck cxtcnsir>nal vein- fractures. Hydrothermal mineralisation localised around such structures testifies to their importance as conduits for fluid flow. Mesh structures are most commonly developed in situations approximating bulk pure shear but predominantly simple shear meshes also occur. They appear to develop through the infiltration of pressurised fluids into a heterogeneous rock mass with varying material properties. In some circumstances, mesh formation appears to be a precursor to the development of major throughgoing faults. Mesh formation generally involves hydrofracturing (Pf> a3, at least locally) and the condition Pf - 63 to be maintained for the mesh to remain a high permeability conduit, requiring fluid overpressuring at other than shallow depths in extensional-transtensional regimes. The volumetric character of earthquake swarm activity appears to result from the passage of hydrothermal fluids through mesh structures, representing a form of distributed fault-valve action along suprahydrostatic hydraulic gradients arising from magmatic intrusion, compaction overpressuring, metamorphic dewatering, etc.

Jan 1, 1995

By Abdalla MH

The deformation resulting from the presence of a tunnel may signifcantly affected, nearby structures and need to be considered during design of both tunnel and structure. The aim of this paper is to study the effect of different factors which may affect the interaction between the tunnel and the str- ucture. These include; the depth of both tunnel and foundation level of the structure ( z and t ), distance between C.L. of tunnel and loads, breadth of the loaded area, Diameter of tunnel and lining of the tunnel. The problem is studied as a two dimensional plane strain model by the boundary element technique. The results of this study indicated that the presence of a cavity/tunnel increases, in general, the vertical displacement on the ground surface and at the foundation level as well as the horizontal and vertical stresses in the cavity/tunnel level. The effect of eccentricity is increasing as e/D decreasing. For pile foundation there is a quite different- influence of the presence of cavity/tunnel in both cases of friction pile and end bearing pile type of foundation.

Jan 1, 1987

By D J. Fray

In this work, a fused salt electrochemical process was investigated experimentally for production of metals and alloys directly from respective solid oxides by electro-deoxidation. Direct electrochemical reduction of the oxides was carried out in molten CaCl2-based chlorides in an electrolytic cell, incorporating an oxygen-evolving inert anode, over the temperature range of 850 - 950¦C. The technical viability of the process was demonstrated by the electro-deoxidation of pure oxides and oxide mixtures including NiO, Nb2O5, Nb2O5/TiO2 and Nb2O5/SnO2 to produce nickel metal, niobium metal, NbTi alloys and the intermetallic compound, Nb3Sn. Compared to the conventional metallurgical processes for producing these metals and alloys, this new electrochemical process appears to be much less energy intensive, with lower costs and no direct greenhouse gas emissions from the electrolytic reduction process. The present electrolytic reduction process has the potential to be scaled up for the green extraction of a number of non-ferrous base metals and processing of many advanced alloys.

Jan 1, 2006

By Muir D

A review of the various methods of degrad- ing cyanide either from gold processing liquors or electroplating baths is presented with some discussion on their relative merits or problems. Whilst alkaline chlorination is common practice in many U.S. and Canadian plants it poses particular problems for certain plants. Alter- native methods include electrolysis, hydrolysis and air oxidation with activated carbon as catalyst which are also integral steps in the carbon-in-pulp process. A basic study of the degradation of cyanide ion has been carried out therefore to determine the effect of temperature, oxygen and carbon. It is shown that carbon is an excellent catalyst for degradation by air and likely to lead to higher losses of cyanide in a C.I.L. circuit. Degradation by hydrolysis is important at high temperatures and high pH such as employed in the Pressure Zadra or Anglo elution processes. Carbon catalysed degradation of cyanide by oxygen in effluent streams may be an environmentally acceptable alternative to conventional chlorine degradation.

Jan 1, 1987

By Jimbo I, Ogawa O

A series of experiments was carried out to investigate the solubilities of copper, arsenic, antimony and bismuth in silica-saturated iron silicate slags under controlled oxygen partial pressures at 1200 and 1250¦C. Molten copper containing each of the above elements was kept in contact with a slag in a silica crucible for 24 or 48 hours to attain equilibrium. No me- chanical entrapment of metal into the slag was observed. The appearance of the magnetite phase in the slag was avoided by holding oxygen potentials at substantially lower values than that evaluated from available data on iron silicate slags. Solubilities of copper, arsenic, antimony and bismuth in slags were plotted against oxy- gen potentials and both oxidic and atomic types of dissolution were found, except in the case of arsenic, from the dependencies of the solubili- ties on the oxygen potential and from positive intercepts of regression lines when extra- polated to zero oxygen potential. The dissolu- tion of arsenic seemed mostly oxidic. Distri- bution coefficients of arseò,ic, antimony and bismuth between copper and slag are also Discussed.

Jan 1, 1980

By Borgelt B. V, Perry A. J, Wellington H. K

There has been little change in the lead smelting practice at Mount Isa since 1939 when the metallurgy and general practice were outline by Raney and Blott.The purpose of this paper is to descriqe some of the operational details that have influenced the overall production. The slag fall hns been increased by the lowering of the lead content of the concentrate. Further, as it is the practice to include iron on the furnace charge and carry a higher lime content in the slag, both factors have produced notable results in furnace operations.All blast furnace gases are filtered in a baghouse and this unit is. being further extended to take all smelter gases, thus eliminating the existing Cottrell plant handling Dwight-Lloyd gases.The lead smelter was closed down from April 1943, to May 1946, during which time blister copper was produced.The report is subdivided as follows:-1. Filtering and Mixinga. Effect of calcium sulphate on cloth.b. Dwight-Lloyd charge composition.c. Main mixer.d. Return sintel sizing.2. Blast Furnace Operationsa. Introduction.b. Use of orehearth.

Jan 1, 1953

The economically significant seams in the Bowen Basin fall into four age groups, two in the Lower Permian and two in the Upper Permian. Coal deposition in the Galilee Basin did not commence until late in the Lower Per- mi-an and persisted into the Upper Permian. The Lower Permian and early Upper Permian coalfields of the Reids Dome Beds, the Collinsville Coal Measures and the Fair Hill-German Creek Formation are restricted to the west flank of the Bowen Basin. The uppermost Permian Rangal-Elphinstone-Baralaba Coal Measures have widespread distribution across the northern half and on both flanks of the Basin. Coal Measures in the subsidiary basins at BlairAtho/ and Ca/en were probably deposited at the same time as the Collinsville Coal Measures. The structure of the north west flank of the Bowen and the east flank of the Galilee Basin is essentially simple, but in the remainder of the basin doming and faulting complicate the structure. Also, bordering a large sec- tion of the east flank, is the Dawson Tectonic Zone, where the beds are tightly folded and faulting is intense. Cok- ing of seams is common in the northern sector of the Basin associated with igneous intrusion. With the exception of the Duaringa Basin on the east flank of the Bowen Basin, Tertiary sediments and basalt flows are more common at the western basin margin. Thick deposits of Tertiary sediments also occur in the south of the Galilee Basin. Con- sequently, coal subcrop, especially in the older, more westerly situated, coal measures is often at depths in excess of 100 m. East of this, the depth of weathering can be as shallow as 13 m and most of the coal subcrop is acces- sible to mining by open cut techniques. Coals deposited in the early Upper Permian are commonly more vitrain rich than those above and below. In the Bowen Basin, coal rank decreases from the north west to the south east, that is, from the semi-anthracites associated with the Dawson Tectonic Zone to the sub-bituminous coals of the southern Galilee Basin.

Jan 1, 1975

The cost-effectiveness of blasts involving radiating blastholes is cur- rently restricted in the following ways. (a) Significant percentages of potential explosion energy are not being liberated; the collar sections of some charges are being dislocated and/or desensitised by the detonations of adjacent earlier-firing charges. (b) If the minimum charge spacing is too small, detonation of an early- firing charge can initiate an adjacent charge sympathetically, thereby eliminating the benefit of any intended inter-charge delay. (c) The overall distribution of energy is poor. Appreciably better fragmentation would be achieved if current drill- ing patterns were to be replaced by staggered fans/rings having a toe spac- ing : burden ratio of about 4 : 1. This wide-spaced pattern would enable a higher percentage of the potential energy to be released, would reduce the incidence of sympathetic detonation and would provide a superior overall distribution of this liberated energy. If improved fragmentation is not required, the proposed fan/ring design should allow a significant expansion of the blasthole pattern with consequential cost savings in drill- ing, explosives and initiation.

Jan 1, 1988

By A S. Ray, P S. Thomas

The characterisation of the surface area and porosity of opals derived from Tintenbar, a volcanic environment, and Lightning Ridge, a sedimentary environment, using nitrogen gas adsorption at -196¦C is reported. Both opal types were found to have relatively low surface areas and displayed little porosity. The low surface areas observed is indicative of the ability of silica to infill voids and interstices. Thermogravimetric analysis of the samples before and after degassing was carried out to determine the amount of water removed by the degassing process. Negligible difference was found in the water content before and after degassing in the case of the Lightning Ridge sedimentary opal, while the Tintenbar volcanic opal was found to have lost more that 60 per cent of its water during the degassing process. These differences were ascribed to the differences in the silica structure of the opals with the Lightning Ridge opal having a denser cage structure, which traps the molecular water, while a more open structure is postulated for the Tintenbar opal, allowing the water to be relatively easily removed.

Jan 1, 2008

By J Sykes, W Treasure, A Saleem, A Trench, S Ulrich, R S. Davies

Below-ground technical complexity remains a traditional source of project challenge. Above-ground challenges then augment this complexity, including in the domain of commodity marketing. All challenges must be solved to produce quality, saleable, ex-mine product. The situation is further complicated in that technical complexities are not independent of each other, so complexity is best regarded as a system rather than a series of isolated factors. Additional above-ground challenges to mining projects are also increasingly sourced from societal and environmental factors, locally and globally. These challenges not only confer project complexity, but have their source in larger, global wicked problems. Finally, financing and resourcing of projects represents an ever-present challenge for all but the highest-quality mineral deposits. CITATION: Trench, A, Davies, R S, Saleem, A, Sykes, J, Treasure, W and Ulrich, S, 2018. On the sources of complexity in contemporary and future mining projects, in Proceedings Complex Orebodies Conference 2018, pp 65–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By D A. Shushkov

Analcime-bearing rocks are one of the varieties of raw zeolite material, although the characteristics of analcime are not as good as other kinds of zeolites such as clinoptilolite or mordenite. However, some fields of application of analcime-bearing rock have been found, eg a method of water purification has been developed and patented. Analcime-bearing rocks are rather widespread in the Timan region of the Komi Republic of the Russian Federation. They are represented by Upper Permian siltstones and mudstones. The analcime-bearing rocks have the following mineral composition (per cent): clay minerals (50 - 70 per cent), quartz (ten to 30 per cent), analcime (one to 30 per cent), feldspars (two to ten per cent), carbonates (two to five per cent) and pyroclastic material. Analcime aggregates encrust cavities and infill microfissures in rock. Both microcrystalline (crystals <0.01 mm in size) and medium-crystalline (~0.5 mm) aggregates are observed. The mechanical, gravitational, magnetic, sorption and ion-exchange properties of analcime-bearing rocks have been studied. They are characterised by a high index of grindability and a low index of abradability and crush resistance, low values of the benzol-based pore volume and toluene-based specific surface area, and a medium porosity value. The magnesium based ion-exchange capacity (IEC) ranges from 28.7 to 196 mg+equiv/100 g. Analcime-bearing rocks of the Timan region are characterised by low beneficiation potential. Preliminary ultrasonic treatment of the analcime- bearing rocks is efficient for the destruction of intergrowths along their boundaries and production of free analcime aggregates. The proposed beneficiation procedure yields 95 per cent analcime concentrate. In the Komi Republic, analcime-bearing rocks are utilised in agriculture. They are also used for domestic needs (eg as biotoilets for domestic animals) and the solution of ecological problems (regeneration of soil polluted by oil). We have completed experiments on the purification of potable and industrial water using analcime-bearing rock subjected to thermal treatment. The experiments demonstrated that it was possible to decrease water colouration by 20 per cent, turbidity by 79 per cent, permanganate oxidation by 30 per cent and total iron content by 70 per cent.

Jan 1, 2008

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

Western Mining Corporation (W.M.C.) operates a nickel refinery at Kwinana, 30 km south of Perth. The refinery commenced pro- duction in May 1970, with a rated capacity of 15 000 tpa of nickel metal. A hydrometallurgical route was chosen as the most expedient way to produce nickel metal at a time when world demand for nickel was outstripping the supply. Later events dictated that an increase in production from the refinery be achieved. To this end, matte produced from Kalgoorlie Nickel Smelter, which was commissioned in 1972, was used in varying proportions as a complement to the concentrate initially utilised as input to the refinery. The effect of matte addition was to increase the capacity to 30 000 tonnes of nickel per annum. This was accompanied by other benefits which were 1. reduction in energy consumption per unit of nickel produced, 2. improved metal extraction, 3. improved precious metal recovery, 4. reduced production of ammonium sulphate by-product. Refinery operating results for the years 1970 to 1983 show how matte feed has improved refinery performance in these areas.

Jan 1, 1984

Compared with modern longwall coal mining systems, automation has not been developed very far in the underground metal minin industry. One of the main reasons for this is that present har rock mining systems do not produce ore with a controlled degre of fragmentation. The often poor fragmentation from the stopescauses large extra costs and precludes material which 1-ends itself to automationThe paper investigates the possibility c technology for automatic loading and trapconveyor belt to a shaft dump pocket. With this concept, it will be necessary to control the maximum fragment size by careful blasting design. The degree of fragmentation will have to be finer than is common to-day. The study shows that the belt conveyor mining con-cept with controlled fragmentation may be economically competitive with conventional cyclic loading and transport, even for an annual production as low as 0.5 mill. tonnes.. Fragmentation design and cost calculations have been based on a combination of the Kuznetsov relationship between blasting parameters and mean frag-ment size, and the Rosin-Rammler formula for fragment size distribution.

Jan 1, 1985

By J Purandare, D Murdoch

The goal of the life-of-mine plan is to ensure that while the site is left safe, stable and non-polluting, the landscape is such that optimal use can be made of the site post-mining and closure. However, in the face of evolving shareholder expectations and the current international economic climate, numerous mines are ceasing operations and moving into a care and maintenance phase. These changes bring with them a high degree of community concern, not only about the potential legacy of closed operations, but also those mines that continue to operate.While mines across Australia are committed from the earliest planning stage to develop clearly defined post-mining land use and landform objectives, broader expectations related to these objectives may change and evolve during the life of the operation. This is especially the case where a mining operation has a project approval where the land use objectives are aligned to land capability and land use commensurate to that which occurred premining. CITATION:Murdoch, D and Purandare, J, 2016. Optimising land for beneficial use during and after mining, in Proceedings Life-of-Mine 2016 Conference, pp 166–167 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By R Pax

Feed ore variability, the major disturbance into a mineral processing plant receives considerable attention operationally, and at research and strategic levels to ensure that the throughput of the ore are maintained at all times whilst encouraging a sustainable approach to recovering the valuable minerals from ore bodies. Effort and insights from mineralogical and processing characterisation (eg. ore hardness) of sub-ore body domains allows sequencing for processing to ensure consistency and throughput for the size sensitive grinding unit processes. Optimising the blast fragmentation has benefit as does pre-concentration using ore sorting. Blending of ore domains with different characteristics is common for operations. In recent years a number of technologies have become available for on-line and more rapid assessment of ore and have been discussed in a recent paper by Cameron et.al. (2016) as an opportunity for further utilisation of mine-to-mill (and mine to product) strategies. Current concepts have focused on extensive characterisation of ores so that current control practices can be realised and made more effective with relatively slow measurements and actuation. CITATION: Pax, R, 2018. Dynamic concepts for mine to mill operation and optimisation, in Proceedings Complex Orebodies Conference 2018, pp 124–125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018