Search Documents

By Kallioinen J

This paper discusses different possibilities to enhance coarse particle flotation using forth manipulation and improved flotation cell design. Experiments were carried out in laboratory, pilot and industrial scale ranging from 0.0015 to 100 m3/axle. During the work it could be shown that the conventional idea of one single flotation cell type for both fine, immediate and coarse flotation of coarse and fine particles need different impeller tip speeds and a different froth control objective for effective operation. For optimal operation for coarse feeds the tip speed must be reduced and the froth vertical velocity must be increased to compensate the respective drainage velocity and also the water film thickness must be taken care of. Turbulent eddies below the froth interface should be suppressed. The paper discusses the effects of different froth manipulation variables like froth vertical velocity and froth residence time to the recovery and selectivity. A function has been developed, between the residence time of the froth and the flotation cell's ability to produce an improved concentrate grade as a function of different operating and froth manipulation variables.

Jan 1, 1993

By Corner NG

A sea bed sampling programme by CRA Exploration Pty. Limited over an area of 12000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 100 m and contained a high grade core of 33 km2 which averaged 283 mghn3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10-40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 It turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

By A Bagis

Road tunnels are an accepted and effective transportation solution in urban areas to mitigate increasing traffic congestion and facilitate improved urban connectivity in a cost effective manner while meeting societal goals to reduce the impact of construction. In designing a tunnel system, there is a requirement to achieve an acceptable level of in-tunnel air quality, as well as meeting ambient air quality goals. In Australia, there is also a requirement for zero portal emissions which means that all pollutants must be emitted to the atmosphere via a ventilation stack.Traditionally, effective pollutant dispersion has been achieved by constructing tall ventilation stacks which disperse pollutants into the atmosphere at a high level. The dominant variable parameters in the effectiveness of the dispersion under the ventilation engineers control are the efflux velocity, the height of the ventilation outlet and the concentration of pollutants at the point of discharge. During off-peak operations the required ventilation exhaust rate can be reduced due to the decrease in traffic. This can lead to a drop in the efflux velocity from the stack and therefore the effectiveness of the dispersion. This potentially drives the need for a higher outlet, or an increased exhaust rate to achieve a higher efflux velocity with consequent effects on energy consumption.The paper proposes a method of varying the cross-sectional area of the ventilation stack with the use of motorised control dampers, thereby maintaining a sufficiently high efflux velocity throughout the 24 hour period independent of traffic conditions. This allows the use of a potentially shorter ventilation stack.

Mar 8, 2011

The southern portion of the Swan Coastal Plain, a geomor-: phological element formed since late'Tertiary times, contains commercially exploitable accumulations of ilmenite, zircon, rutile'and monazite associated with a series'of raised'shorelines. The:location'of the deposits is controlled by a locally outcropping*Archaen-granite/granulite complex and a sea':current pattern'determined'by'local geography and a prevailing wind direction.'-A progression from medium. to high titanium ilmenite is'evident parallelled by. progressive leucoxenisation as the age of the deposits increases. Variation's in trace element content accompany this process. Circulating groundwater has caused vertical mineralogical variations within-individual deposits and' by p'ecipitation of iron has formed layers of hardpan. The economic sig- nificance''of the Geographe--Bay deposits is'briefly discussed,

Jan 1, 1964

By Chappell BW

A zone of northwest trending dykes extends for over 600 km in the hinterland from Cairns to Mackay. In sate regions the zone is up to 120 km wide. Figure 1 shows their approximate extent, compiled from published regional maps and from specific studies in more limited areas : Palm Islands, Cardwell Ranges, Jourama Falls, Townsville area and Burdekin Delta. The context of the dyke swarm is the Tasman Orogenic Zone, the region of Eastern Australia conprised of Palaeozoic metamorphic, sedimentary, volcanic and plutonic rocks which has experienced a complex history and evolution. In the Whitsunday region, the Tam-an Zone also involves Cretaceous volcanism and plutonism. Geological relationships indicated a wide span of ages for the intrusions in the dyke, swarm zone. They intrude a range of volcanic and sedimentary rocks, and in some areas plutonic rocks. Older dykes, apparently part of the same regional swarm are intruded by sate of the granites.

Jan 1, 1987

By Bulters J, Sheppard I

Two blasthole density logging programmes have been conducted on the Mt Whaleback iron ore mine to evaluate the use of this type of logging as an aid to blast pattern design. The first programme also involved the setting up of a Density Test facility with which to calibrate the density probe. The programmes indicated that about 22-23 blastholes can be consistently logged per day at a cost of $1.30 per metre. Even though this is only half the rate required to log the average number of blastholes drilled daily on Mt Whaleback, testwork indicated that no significant loss of accuracy results if only half the holes in a pattern are logged. The major results of the programmes were: 1. The density range for black pyritic Shale is 2.2-2,9 g/cc. 2. The density range for soft to medium hard BIF is 2.1-3.0 g/cc. 3. The density range for hard BIF is 3.0-3.6 g/cc. 4. The front row blastholes show consistently lower densities than the main body holes due to blast damage. 5. A low density zone extending to a maximum depth of 6 m occurs at the top of most blastholes and results from blast damage from the bench above. These density results have been used to implement savings in drilling and blasting via pattern expansion and charge optimisation of blastholes. Eight ore

Jan 1, 1986

FIRST TOWN PLANNING PROPOSALS Initially, accommodation at the minesite was provided at the Pastoral Homestead situated some seven kilometres north-east of the mine and between 1963 and 1966 was the base of the exploration camp. Tents were used for sleeping of 100 men and the Homestead used for dining and office facilities. With the beginning of ore production and shipment due to commence in 1969 a permanent town location was sought. Early town planning studies had been commissioned by Amax Inc. and Colonial Sugar Refining Co. Ltd. and in 1967 The Broken Hill Proprietary Company Ltd. took over the responsibility for putting them into effect. The location chosen was about four kilometres due east of the mine. Certain dominant factors influenced this choice. It was near enough to the mine to share services, yet far enough away not to be affected by dust and noise and received the additional shelter of a range of hills separating it from the mine. A predominant slope to the east provided good drainage and the ground was easy to excavate for services.

Jan 1, 1976

By Wilson O. A, White R. W G

The Mount Morgan mine occupies a unique place in the mining history of Australia and although not as glamorous during the second phase of its existence, it made a significant contribution to the technical and financial history of the nation throughout its life. The stories of the intrigue surrounding its discovery and early operation, the enormous return received by its original investors in its first five years as a public company, its influence on the local, national and international scene to its final closure have been documented in many publications, the most recent and authoritative being by John Kerr (1982). Institute publications as far back as 1911 have documented details of the mining, metallurgical and engineering practices of the two companies which worked the 100 or so acres which were alleged to be `the richest single gold mine in the world'. Within the Institute records appear the names of Presidents, Institute Medal recipients and others connected with Mount Morgan who have played an important part in the Institute history.

Jan 1, 1993

By P Tobar

The development plan (long-term plan) of El Teniente Mine, Codelco-Chile, includes 100 per cent primary ore, located at increasing depths, which may involve several difficulties related to the application of the current panel caving method, such as a high seismicity level, a coarse fragmentation and ore pass damage. Therefore, it is a strategic priority for the El Teniente mine, to design and to test alternative mining methods, at similar or lower costs to ensure an efficient and safe ore extraction. In this context, the Macrotrench method is developed, as a competitive alternative to the current method. The document describes the panel caving method, the experience achieved in the primary ore exploitation from the geomechanical point of view. It also describes the æmacrotrenchÆ method as an alternative to the current exploitation method. Finally, the comparative advantages of macrotrench in relation to panel caving are presented. The results obtained during the engineering stage include the following aspects:the mining design, the material handling, a geomechanical evaluation of the method, and a comparative analysis.

Jan 1, 2000

Giving the keynote address in the final session of a conference dealing with closely related topics has a disadvantage in that much of what can be said has been said. It also has an advantage, however, because it presents the speaker with the opportunity to integrate and analyse the material presented by the various speakers. I would like to look to the near future in Aust- ralia and the United States of America, to the risks, problem areas, and changes of a rapidly evolving post-industrial era-an era we are begin- ning to experience where industry no longer `calls the tune'. We miners have been quick to point out and emphasize, that ours is a `high-risk' industry in the world of business and commerce. Yet, clearly those who have survived, and been successful, have learned to anticipate and cope with risk and change. This ability has been a distinguishing feature of the industry's leaders who, in market studies and commodity selection, exploration and development, mine planning, metallurgical pro- cessing, and general administration and operation 1. identify areas of risk or inevitable change, 2. analyse, test and quantify those factors of risk or change, and 3. design methods, systems, equipment to elim- inate, moderate, or control or economically compensate for predicted risks or changes.

Jan 1, 1978

From December 1994 to November 1997 Odin MiningÆs Estero Hondo alluvial gold mine in western Ecuador washed almost 3.2 million bank cubic metres of gravel to produce just over 2600 kilograms of pure gold at a recovered grade of about 0.8 grams per bank cubic metre. The operation was a simple open pit. Draglines stripped the overburden, backhoes mined the gravel, and trucks transported the ore to a stationary, gravity-based wash plant for processing. At start-up the planned throughput was 55 000 bank cubic metres/month, but a year later this had been increased to 100 000 bank cubic metres/month. From April 1993 to July 1997 a total of 440 churn drill holes and 15 pits were sunk to test the property. The methods used to prepare the resource and reserve estimates from the raw field data are described, and seven sets of completed estimates are used to track the evolution of the projectÆs resource/reserve base through the exploration, feasibility and production stages.

Jan 1, 2003

THE alkaline method for the estimation of zinc cannot, in the writer's opinion, be relied. upon to within very narrow limits between two assayers on unknown quantities of zinc. The end point is not decisive enough, and allows the personal factor toenter largely into the assay. The following investigation was undertaken to see how accurate the acid method is on Broken Hill concentrates and ores, and what should be the limit between the results of two assayers. The method adopted is as follows:Weigh sufficient amount of ore to give titration (between 20 and 50 cc.), place in tall 400 cc. beaker, cover, add 7 cc. nitric acid and heat till brown fumes cease to be evolved. Wash dock glass into assay, add potassium chlorate, evaporate to dryness on a slow fire with the beaker uncovered. When no smell of chlorine or nitric acid is observed, remove and cool. Add 100 cc. boiling water, then 7 grm. ammonium chloride, W cc. ammonia (.880 sp. gr.), boil for five minutes, filter, wash...

Jan 1, 1911

By G Marling, A Calderon, J Harris, P Kirsch, M Shi, D Sprott, A Kirsch

Large-scale infrastructure construction needs to comprehensively manage risks that can impact the health and well-being of many people, from workers (temporary, contracted or full time), to families and surrounding communities. This paper starts with an analysis of incidents (injury, fatality, other damage) in tunnel construction between 2000 and 2014 and assesses the distribution of these events by continent, year, and severity of outcomes. These incidents are then analysed and mapped to a framework of hazards derived from RISKGATE (2014). A comparative register of current tunnel construction risk management guidance is derived from current Australian codes of practice and this register is also mapped to the RISKGATE framework of hazards to identify where coal industry knowledge may offer utility to the tunnelling industry.An initiative of the Australian Coal Association Research Program (ACARP), RISKGATE is an interactive online risk management system developed to assist the mining industry in implementing continual improvement in the management of major unwanted events. To date, a comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, outbursts, coal bumps and bursts, human/machine interface, manual tasks, slips/trips/falls, inrush and occupational hygiene. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.This paper proposes and outlines how knowledge within the RISKGATE platform could be applied to managing the significant health and safety risks associated with tunnelling. The authors suggest that to varying degrees the knowledge already captured in RISKGATE is likely to be transferable to tunnelling construction operations. Please note that this paper focuses on tunnel construction and does not address risk management of tunnels in operation (eg road transportation or utility networks).CITATION:Kirsch, P, Kirsch, A, Calderon, A, Marling, G, Harris, J, Shi, M and Sprott, D, 2014. Management of health and safety in tunnelling – application of Australian coal mining knowledge, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By K Mayank, A N. Mainza, I Govender, M Narasimha, A Mittal

In mineral processing industries grinding is the most energy-consuming process. A tumbling mill is an essential grinding equipment widely used for particle size reduction. Power consumption, impact forces and trajectory paths are critical parameters for characterising a tumbling mill to determine grinding efficiency. The effect of lifters and mill speed plays a vital role in such parameters. However, most of the studies ignore the impact of the lifter and do not investigate the effect of slurry dynamics on charge motion. The focus of the present work is to prepare a computational model that can accurately predict the complex multi-phase dynamics of charge particles, air and slurry inside the mill using a model that couples computational fluid dynamics (CFD) and the discrete element method (DEM). The details of impact forces with lifter profiles and mill speed variations will be refined even further using the CFD-DEM coupling approach. The slurry-air free surface is modelled using the volume of fluid (VOF) method, and the charge motion is modelled using the DEM. The phases are coupled using the interface momentum exchange between the charge and the fluid slurry. The coupled model is validated against experimental results from the positron-emitting particle tracking (PEPT) data. The validated model compares the effect of slurry content on charge dynamics with the dry DEM model. The presence of slurry is observed to dampen the tangential and shear contact forces.

Aug 24, 2022

By P Mavros, K A. Matis, N K. Lazaridis

A large number of techniques are in use today to limit membrane fouling, among them certainly is air bubbling (which constitutes the transport medium in flotation) as applied in wastewater treatment; meanwhile, dispersed-air flotation is suitable as a pretreatment stage for microfiltration. The invented and investigated hybrid cell combines the advantages of both flotation and membrane separation, while overcoming their limitations, producing clean water from industrial wastewater. Metals recovery from dilute aqueous solutions is a promising application of this innovative hybrid process of flotation and microfiltration, further to solid/liquid separation. In this study, ceramic flat-sheet membrane modules were inserted inside a typical flotation cell in the laboratory tests, using multichannel geometry, combining flotation with microfiltration by submerged membranes; the latter requiring periodic backflushing. The specific objective was to apply this process for the efficient separation of effluents containing metal cations (here, zinc). The main examined parameters were: the initial metal concentration, flotation surfactant applied and air flowrate. The successful contribution of precipitate flotation was highlighted, while the observed metal removals were of the order of ~100 per cent.

Jan 1, 2005

By R Bourcier, T Rafferty

Following an underground coal mine explosion, it is important that ventilation is quickly restored to ventilate the mine and affect a mine rescue. To achieve this, surface ventilation fans must be suitably protected from explosion damage, but still able to be quickly restored.A review of all Australian coal mine regulations was carried out, revealing that Australia has no prescriptive regulations that specify the design of explosion relief panels and the protection of ventilation fans in the event of an underground explosion.To better define the level of protection required, this paper reviews and extracts details from relevant major international regulations and standards on the subject.A suitable design methodology for the protection of ventilation fans is presented that could be applied in Australia, using a combination of explosion relief panels, appropriate isolation of the fan, and ventilation shaft/mine design.CITATION:Rafferty, T and Bourcier, R, 2013. The protection of surface ventilation fan installations from underground explosions, in Proceedings The Australian Mine Ventilation Conference , pp 169-173 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R Marchant, D Willingham

"Predictive maintenance (also known as PHM or equipment ‘health monitoring’) refers to the intelligent monitoring of equipment to avoid future equipment failures. In contrast to conventional preventive maintenance, the maintenance schedule is not determined by a prescribed timeline; instead, it is determined by analytic algorithms, such as machine learning, using data collected from equipment sensors and/or via simulation.Predictive maintenance offers the following benefits for operators and equipment manufacturers:reduction of equipment downtime by identifying issues before failure, thereby enabling convenient scheduling of equipment service and extending equipment lifetimeautomatic determination of the root cause of the failure, enabling appropriate service to be performed without utilising resources to determine a diagnosis avoidance of costs of unnecessary maintenance and unexpected failures improved safety and product quality.Algorithms and data are critical to predictive maintenance success. Sensor data preprocessing is performed using advanced statistical and signal processing techniques. In the case that data isn’t available for the full range of operating modes, operating scenarios can be simulated. Machine learning techniques are then used to estimate equipment health. Once tested, predictive maintenance algorithms may be operationalised in an IT environment such as a server or cloud. Alternatively, algorithms may be implemented in an embedded system directly on the equipment, allowing for faster response times and significantly reducing the amount of data sent over the network.In this paper, we use both historical and simulated data of the plant under various modes of operation including run to failure, and we then leverage machine learning techniques in MATLAB to estimate degradation and remaining useful life. This technique, of combining both simulation models and machine learning, in the areas of predictive maintenance and equipment health monitoring has been adopted by Safran, makers of aircraft jet engines, since 2007. They now have over 160 modules developed (Lacaille and Aurelie, 2015).Citation:Willingham, D and Marchant, R, 2016. Predictive Maintenance Using Simulation and Machine Learning, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J A. de la Torre, I R. Cerna, G K. Karadjian

The La Colorada underground mine in Zacatecas, Mexico is a mechanised cut-and-fill silver mine with a capacity of 1250 t/d. The project focused on training the mine’s experienced operators for a fleet of underground trucks, through the use of a training simulator. The project was run by the simulator vendor, in collaboration with the mine’s maintenance, safety and production management.A training program was created targeting maintenance reduction, productivity improvement and increased utilisation and availability. Operators were first acclimatised to the simulated environment, had their current performance baselined, then received targeted coaching, with the process repeated to reinforce learnings. Concurrently, production, maintenance, and safety data was being measured in the real world to measure skills transfer. Due to limited telemetry available from the equipment, many of the data points for the project were sourced from maintenance logs, and accounting data.Equipment failure data measured from unscheduled maintenance records showed an overall 6.5 per cent decrease in unscheduled maintenance following the implementation of the training program. This rate of reduction correlated with the significant decrease in equipment abuse behaviours measured within the simulator during this period. Additionally, overall maintenance activities showed a significant decrease, confirming that reductions in unscheduled maintenance were not achieved through increases in scheduled maintenance. The reduction in equipment damage also increased availability and utilisation of the truck fleet. This highlights that the maintenance improvements not only reduced maintenance costs, but made the fleet available for more production. Moreover, the variability of the operator performance was decreased by 86 per cent, and the difference between their best operator and the worst is less than the baseline; this showed a gap where machine abuse, productivity and cost are impacted directly.This project illustrated that even small-scale mining operations with an experienced operator workforce can achieve positive return on investment (ROI) from simulation-based training. It also highlights that in the absence of equipment telemetry, alternative data sources such as accounting data and maintenance logs can be used to quantify ROI from training.CITATION:Karadjian, G K, de la Torre, J A and Cerna, I R, 2017. Innovations in underground hard rock operator efficiency – through simulation-based training technologies and processes, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 53–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

Blasthole cone samples are used for grade control in most of the iron ore mines of the Pilbara of Western Australia. This method of sampling is straightforward when the target sampling interval matches the mining bench height but is problematic when the blasted bench is 'flitch' mined in two or more passes. Crucially, the sampler needs to decide which part of the blast cone represents the upper and lower flitches to be mined. This sampling selection decision is usually made by assuming a certain proportion represents the subdrill component of a sampling face in a blasthole cone and the two flitches are split equally from the remaining portion. In this study of a West Australian channel iron deposit, sampling experiments were carried out to determine the actual proportions of a sampling face in a blasthole cone by spray painting the blast cones at flitch and subdrill boundaries during the drilling process. Measurements were then taken to assess the differences between assumed sampling face proportions and actual proportions. A set of paired samples was also collected from a number of blastholes with one set using the assumed proportions of each flitch for each sample, while the other set sampled the actual proportions, which were identified from the cone painting process.

Mar 1, 2010

By N Boughen, K Moffat, L Brooks, A Zhang

In 2015, Ernst and Young (EY) ranked socio-political license to operate (SPLTO) as the fifth greatest challenge to the mining sector (EY, 2015). The EY report asserts that SPLTO will continue to present a risk to the mining sector in the context of ‘increased activism, digitally connected stakeholders and politicians who need to respond to general consensus’. While there is no consensus on a definition, SPLTO is commonly regarded as the ongoing acceptance or approval of an operation by affected stakeholders (Moffat and Zhang, 2014; Thomson and Joyce, 2008) as well as those stakeholders that can affect the operation (Graafland, 2002). Warhurst (2001) relates the process of stakeholders granting SPLTO to the establishment of meaningful partnerships between operations, communities and government based on a variety of factors that build trust between stakeholders.From these accounts, we can see that understanding stakeholder attitudes about company performance and impacts on stakeholders directly affected by an operation are important in any attempts to measure SPLTO. Understanding the level of acceptance of an operation within these stakeholders provides a good proxy or outcome measure of SPLTO. Moreover, trust seems to be a central variable in the translation of these experiences of an operation into acceptance. What the mine or company does, its behaviour, degrades or builds trust with stakeholders, and this then affects acceptance (Moffat and Zhang, 2014).In addition, a strong emphasis is placed on the nature of the relationship between companies and stakeholders as influenced by inter-group interactions. It is not just what companies do well or poorly with respect to environmental impacts, for example, that will determine trust and acceptance, but how the company relates to its stakeholders at personal and group levels.These relationships between communities of stakeholders and extractive companies are dynamic. Brown and Fraser (2006) recognised the importance of industry being able to respond to the changing nature of societal approval and acceptance, arguing that ‘business must have regard for evolving social attitudes and expectations if it is to maintain its ‘social licence’’.This paper will describe a series of five pilot projects conducted by CSIRO with Anglo American in Australia and South Africa to generate a real-time understanding of SPLTO to guide more reflexive and effective social performance strategies.CITATION:Moffat, K, Boughen, N, Brooks, L and Zhang, A, 2016. Social licence in real-time – using dynamic methods to support a new kind of community relationship, in Proceedings Life-of-Mine 2016 Conference, pp 191–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016