Search Documents

By M Nagarajan, S Esen

This paper presents three case studies from three surface coalmines. The first case study is from a coalmine where a dragline operates in 60 m wide and 1 km long strips. Typical overburden height ranges from 30 m to 50 m. The base case blast was modelled using an advanced blasting model (Distinct Motion Code – DMC) to establish the baseline using the blasting parameters in use before optimisation. DMC was used to model the alternative blasting scenarios to obtain the following key objectives:the post-blast muck pile profile was required to have an optimum height of ~28 moptimise cast percentageachieve a well-fragmented muck pile for the draglinethe muck pile profile should be appropriate for the dragline entry into the strip.Achieving these objectives would optimise the dragline performance through reducing rehandle and improving advance along the strip. DMC modelling resulted in the following outcomes:the required muck pile profile could be achievedthe cast percentage increased from 21.1 to 25.1 – a four per cent increaserehandle volumes were reduced.Establishing a good quality assurance / quality control (QA/QC) process was essential to delivering a blast that could achieve these outcomes. The blast was fired successfully and the dragline completed the strip approximately two weeks ahead of the time taken for the previous strip.The second case study is from a coalmine where D11 dozers are used to move the blasted material to the spoil. An optimum profile was required for the dozers for this low-cost mining operation. To achieve this, an electronic blasting system (uni tronicTM 600) was introduced to optimise the muck pile profiles being delivered. The new muck pile profiles showed improved cast percentage from 10.6 per cent to 17.8 per cent. The changes in the muck pile centre of mass displacement improved dozer efficiency as a result of pushing material shorter distances to its final position. Dozer productivity (bcm/h) statistically did not change but coal was being exposed at a faster rate.The third case study summarises the results from a site where dozers are used to minimise the total mining cost. Traditionally, excavators had been used on-site with conventional blast designs. After firing the first cast shot, the blasted material was found reasonably well-fragmented. Although dozing productivity hasn’t been quantified on-site, operators were providing positive feedback (easier push) due to the reasonably good muck pile profile suiting to the dozers. This site also realised significant savings with the dozing as compared to their truck/shovel operation.CITATION:Esen, S and Nagarajan, M, 2015. Muck pile shaping for draglines and dozers at surface coalmines, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 409–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Stepanenko, G Stovpchenko, L Lisova, D Togobitskaya, L Medovar

Classical electroslag remelting of consumable electrodes is a drop-by-drop melt feeding through a slag layer into a renewing molten metal bath, slowly solidifying into a homogeneous, dense, defectfree ingot in a copper water-cooled mould. The new look at the additive nature of the electroslag remelting (ESR) process in a protective atmosphere allowed us to formulate the principles of a comprehensive thermodynamic-based model that can predict dynamic changes in slag and metal composition at certain ingot remelting. The model considers drastically different slag-to-metal mass ratios at the beginning and end of remelting and predicts gas, slag and metal composition in a chain of thermodynamic subsystems. Despite consisting of calcium fluoride and stable oxides, the ESR slag can oxidise main and active elements from steel and alloys (primarily aluminium, titanium and silicon) due to chemical reactions between slag and metal. ESR is not an electrochemical process in its nature. However, slags are ionic melts and deviation in their composition causes a change in their properties, affecting both operation mode and ingot quality. Another important understanding derived from the modern metallurgy technological route is that the ability to refine metal from impurities is not a priority for the ESR because consumable electrode has already passed all stages of refining and deep degassing at ladle treatment that changes ESR slags engineering principles. The critical importance became slag’s ability to generate process heat and keep the melting composition in the metal bath unchanged (except for non-metallic inclusions assimilation). Slag engineering for ESR required a compromise between chemical inertness to a metal composition and desired physical properties deriving from technological reasons. The Directed Chemical Bonds Concept (DCBC) in a multicomponent oxide system was used to build predictive models of electric conductivity and the melting temperature of fluoride-oxide slag based on their chemical composition. Both models help to design a customised composition of effective slags for steel and alloy groups or individual grades, and they are significant steps in the development of a comprehensive model of electroslag remelting.

Aug 21, 2024

Alfred Nobel first invented a practical detonator in 1863 and then the blasting cap in 1865. At that time the detonator was used on the end of a length of safety fuse to initiate nitroglycerine-based explosives. Since then the detonator has gone through a number of changes. The instantaneous electric detonator was the first to allow remote firing. The electric delay detonator followed and allowed for timing between holes. In the mid 1970s the NONEL« Tube was invented. This tube combined with NONEL« detonators meant that many of the safety issues, such as stray current and radio frequency, associated with electric delay detonators were eliminated. This system gave the mining industry a reliable and fairly accurate system with which to detonate shots of any size. Since the early 1980s a large amount of research and development work has been done around the world to create a more accurate detonator for the mining and quarrying industry. After years of research, electronic detonators have emerged as the most accurate and precise initiation system available to the mining and quarry industry today. Electronics provide the user with millisecond timing accuracy. The improved level of timing control allows operations to improve fragmentation, throw and reduce vibration levels. There are now a number of different electronic detonator suppliers on the market today. In 2004 Dyno Nobel formed a joint venture called DetNet with AECI. DetNet has a suite of electronic detonators: DigiDet«, HotShot« and QuickShot«. This paper will focus on the HotShot« system, the first of the three new initiation systems to be released to the market in Australia by Dyno Nobel.

Jan 1, 2005

By J Loeb, R Ramanathan, H Ingham, P Cameron

Most mining operations, including iron ore, maintain a focus on continuous improvement and asset optimisation in their operations. As all the unit operations in the Mine-to-Mill value chain are interdependent, available technologies that address efficiencies across the value chain are once again in the spotlight as companies are driven to improve productivity and maximise mine site profits to increase return on capital invested. Core to continuous improvement is the need to understand the baseline and impact of changes to the process. In this paper, we discuss some of the critical attributes in the Mine-to-Mill process, including their influence on productivity and cost, the need for direct measurement and areas where they should be applied. Many initiatives can be considered to improve Mine-to-Mill processes. Mining operations are planned and executed based on designs and models to achieve the operation's objectives. However, there are many variables in the different parts of the value chain, such as blasting, material handling, crushing and screening. Therefore, measurement of the key attributes establishes the baseline for Mine-to-Mill (or Pit to Plant) performance, which is necessary to understand the impact of any proposed improvements to the process design and execution and monitor the outcomes on an ongoing basis sustain the improvements that have been implemented. This paper focuses on two types of measurement – blast movement and particle size of materials through the Mine-to-Mill process. Several innovative technologies and control loops are readily available to measure these attributes and assist operations to improve productivity and mine site profits. The size of the tangible benefits, which can flow from measuring and optimising fragmentation and blast movement, provide a remarkable return on the investment. Realising these benefits needs a focus outside conventional operation silos as a successful Mine-to-Mill project requires a multidiscipline approach across all the silos in the value chain. Required technologies are available; adding the necessary ingredients of communication and co-operation by all concerned across the silos will ensure the benefits are realised.

Nov 8, 2021

By A Finch, C Pridmore

The Cosmo Project falls within the Archaean to Palaeo-Proterozoic Pine Creek Orogen, one of the major mineral provinces of Australia.The Cosmo Deposit is interpreted to be a series of steep north-west-plunging gold mineralised vein, breccia and shear systems within the tight Howley Anticline and hosted within interbedded siltstones, mudstones, banded iron, phyllites, dolerite sills and greywacke.A folded environment poses a number of technical challenges, particularly for estimation.Handling of tightly folded and in some cases narrow domains might include subdomaining for orientation, omni-directional three-dimensional (3D) estimation within constrained domains or software-enabled unfolding/un-wrinkling procedures (transformation of the data and estimate space into a two-dimensional environment). Each technique has its own unique set of advantages and disadvantages.A further method (one applied at Cosmo) is where the estimation parameters (specifically search and variography orientation) are modified in a frequent or ‘dynamic’ sense to suit the orientation of the domain whilst maintaining 3D space. Control of the resource estimation orientation can be done in several ways, including the use of sectional panels of a specific size or, alternatively, orientation sector divisions. The sector approach provides some significant reductions in processing time over the panel technique and could be applied in a number of software packages.Three-dimensional ‘dynamic’ interpolation reconciles well with production data from Cosmo, whilst the sector method provides a practical technique that can be executed without the complications of transformation or the need for labour-intensive orientation subdomaining and with acceptable resource estimation run time.CITATION:Finch, A and Pridmore, C, 2014. Dynamic interpolation – estimation in a folded environment at the Cosmo Deposit, Northern Territory, Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 107–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By T Baumgartl, B Richards

The association of specific plants and plant communities with soils developed over underlying superficial orebodies and mineralisation has been long recognised. It has given rise to the use of plant indicators for geobotanical exploration as a regular component of primary minerals reconnaissance where there is an undisturbed vegetation cover. That the chemical composition of indicator plants is a measure of their soil environment has further led to biogeochemical prospecting methods for minerals and its use in the mapping of underlying ore deposits. Where there is a strong surface expression of metal and metalloid anomalies, concentrations of potentially phytotoxic elements may reach a level at which they have strong selective impacts on plant populations. In such circumstances, natural selection has operated in the development of a unique flora composed of plant species and individuals with genetically-based tolerances to the stressed environment in which they continue to survive. These plants are called metallophytes. Metallophytes occur globally on all metalliferous sites, both in pristine undisturbed environments and in areas of mineral workings, ancient and modern. However, the best-developed primary metallophyte vegetation is found in the most ancient areas where there has been a long-term evolutionary impact of the underlying geology through ore weathering and dispersion of metals into the rhizosphere zone. Natural selection of metal-tolerant races of plants in these largely undisturbed areas can eventually lead to speciation and the development of an endemic regional metallophyte flora (Baker et al , 2010). Mineral wastes resulting from mining activities also allow colonisation by metal-tolerant individuals leading to the establishment of metallophyte communities. The distribution and extent of such communities is determined by regional and local factors relating to climate and substrate conditions and the availability of suitable plant resources on which natural selection can operate (Baker, 2009).The ability of metallophytes to tolerate extreme metal concentrations commends them as the optimal choice for ecological restoration of mineral wastes and metal-contaminated sites. Metallophytes have recently also spawned several novel phytotechnologies, including phytoremediation and phytomining (Chaney et al, 2000, 2005; Baker and Whiting, 2008). Action towards conserving the global metallophyte resource base is imperative because many species are under threat of extinction from new and extensive mining activities (Whiting et al, 2004). This has been identified as a priority in the Mining, Minerals and Sustainable Development (MMSD) Project of the Global Mining Initiative in 2002 but positive responses from the minerals industry have been slow. The last decade has, however, seen an ever-increasing interest in metal-tolerant and metal-accumulating plants, both from an academic standpoint and their use in revegetation and phytostabilisation (Tordoff et al, 2000; Baker and Whiting, 2008; Baker, 2009). Few studies have highlighted the need to conserve and develop these unique plants (Whiting et al , 2004). This presentation identifies future research needs for the conservation and exploitation of the global metallophyte biodiversity and its potential in sustainable mine closure. CITATION:Baumgartl, T and Richards, B, 2012. Evaporation and salt transport under variable climatic conditions, in Proceedings Life-of-Mine 2012 , pp 179-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By L Vimercati, R Williams

Transitioning to a green future requires the mining industry to adopt sustainable practices. Filtered tailings are become a key expectation of the communities we operate in and are growing in a number or mining commodities including bauxite, nickel, gold and iron ore. The filtration technologies required range from dewatering screens to vacuum and pressure filters. Particular challenges faced in iron ore applications include large scale which means several units of large size are often required. In addition, a high specific gravity that cause sedimentation issues and a high abrasion level make demands on achieving reliability level at above 90 per cent. This paper describes the testing, selection criteria and specific features required to provide a rational option for equipment and plant design. An example of how this has been applied in an iron ore application in Brazil is used to demonstrate a successful outcome. This project installed four overhead beam filter presses each producing around 200 t/hr utilising a recessed chamber plate, feed pressures up to 15 bar, cake thickness of 5 mm. The moisture lower than 20 per cent that was produced was considered to provide material with handling and geotechnical properties to guarantee a safe stacking. Regular high pressure washing at 100 bar was considered imperative to maintain cloth life and process performance. The correct management of the system (OPEX control) by PLC control ensures a balance between machine potentials and plant needs. With this equilibrium it is possible to limit mechanical wear preserving equipment lifetime.

Sep 18, 2023

By P Ramsaywok

The use of saline water for mineral beneficiation in arid regions is general practice and also the case with Exxaro Namakwa Sands, situated on the west coast of South Africa. Although it is ‘cost effective’ to use sea water for mineral beneficiation, downstream process separation efficiencies may be negatively affected. This is more specific to surface dependent separation techniques such as electrostatic and high tension (HT) separation. If minimal fresh water is available then, proper washing is often neglected. Salt crystals can form on particle surfaces during the drying process before electrostatic separation.This paper describes a study that has been conducted to determine the effect of upfront salt water processing on downstream electrostatic/HT separation. The study indicated that minor quantities of salt can cause the separation efficiency to decrease substantially.

Oct 5, 2011

By Marshall T. E, Finfinger G. L

Gulf Coast domal salt mining operations have had sporadic encounters with methane gas emitted without any warning. In virtually all confirmed cases, the methane was localized in methane enriched zones. In a few cases large quantities of methane were expelled rapidly with salt outbursts, resulting in dangerous methane concentrations. Estimates of methane liberated by face blasts in methane-enriched areas is needed in determining how much air should be supplied to the face for proper dilution. A relationship between the gas content of salt samples collected from the face and the amount of methane liberated would be helpful in estimating how much methane will be produced by a face blast. Little is known about the layering or stratification of methane in large area-low velocity airways. This publication reports on three tests conducted by the Bureau of Mines which monitored the immediate return air of four faces during blasting. The test locations were in a methane gas-enriched section that had previously experienced two large outbursts and many smaller ones. A comparison was made between gas content values of face salt samples from the dissolution test and the gas liberation quantities. The characteristic movements of the methane in a large room with low air velocities were charted. This will help to better understand the factors involved in proper placement of methane sensors as a warning system.

Jan 1, 1988

By C D. McCullough, M Gerner

Rarely do opportunities arise allowing closure of a mine site to be planned as a key beneficial land use asset within a new urban growth area; particularly so well prior to cessation of mining.Pit lakes are common mine closure legacies for many open cut mines and may form in open cut mine voids extending below the water table upon closure. Mine closure guidelines increasingly require post-mining land uses of equivalent capacity to premining conditions and that minimise long-term post-mining liabilities and maximise benefits to stakeholders and the environment. However, risks presented by pit lakes are regularly neglected in closure planning or are not able to be addressed to allow beneficial end use of the lake or surrounding land.This paper describes strategic planning initiated by quarry owners ten years before mining ceases. In liaison with the planning agencies, the planned closure of a large 100-year-old limestone quarry pit will form a lake on mine completion, with a well-considered beneficial end use in an urban setting in mind. The quarry pit and adjoining land at Batesford South about the edge of the City of Greater Geelong, Victoria, Australia. Geelong is experiencing growth pressures that necessitate development of a new growth area from about 2025.A multidisciplinary expert team assessed the constraints, opportunities and feasibility of rehabilitating the quarry and pit lake and developing the surrounding land as Geelong’s next urban growth area.The concept is exciting and demonstrates that a former mine site could become a valued home to about 40 000–45 000 people. About 30 per cent of the land will also be developed as an ecological riverine corridor including the pit lake that will become a regionally iconic lake as the centrepiece of an urban development.Our paper outlines technical challenges and how these can be met to achieve closure and beneficial use that meets the social, economic and environmental expectations of contemporary urban planning.CITATION:Gerner, M and McCullough, C?D, 2014. Planning for the future – development of beneficial end use from a quarry pit lake, Victoria, Australia, in Proceedings Life-of-Mine 2014 , pp 99–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M Yahyaei, F Reyes, R Lage, V Jokovic

Equipment wear is strongly related to the performance of grinding circuits. In particular, SAG mills are subjected to the wear of their shell liners and grates. Changes in lifter height and face angle impact mill performance, while classification at the mill discharge is also affected as grates wear out. Moreover, liner mass loss caused by wear affects how operators interpret readings of sensors such as load cells or bearings pressure. Automating and optimising grinding circuits under these constrain becomes challenging due to the nonlinear and dynamic nature of the system. The operation of SAG mill grinding circuits remains largely dependent on human intervention, which frequently results in inconsistencies in performance across shifts, reflecting the operator’s personal preferences, experience, and other human factors. The influence of human factors can be reduced by careful training of operators as well as by automation using advanced supervisory control. The latter approaches could benefit from the development of dynamic process models that consider the effects of wear on the performance of equipment over time. This paper presents detailed industrial data showing the effects of wear on SAG mill performance. Additionally, a dynamic SAG mill model that accounts for these phenomena is proposed and demonstrated in a simulated environment. This model is shown to mimic the effect of wear on the performance of industrial scale mills and the operational constraints they are subject to, thus extending traditional SAG mill models. Incorporating wear into modelling and simulation platforms can improve the understanding of the effects that wear can have on the performance of key assets in comminution circuits and may allow the development of more robust model-based advanced process control strategies.

Aug 24, 2022

By K Tanguturi, B Belle, R Balusu

Management of high rates of goaf gas emissions between 4000 and 6000 L/s of methane gas in longwall panels is a challenging issue, particularly in start-up areas of the panels. There is a need for investigation of the effect of various goaf gas drainage concepts and techniques, and development of effective gas drainage strategies for management of high goaf gas emissions in start-up areas of the longwall panels. This paper presents the results of various computational fluid dynamics (CFD) simulations that were carried out to investigate the effect of different goaf gas drainage strategies and combinations for gas management in the start-up area of the longwall panels. Results indicated that the gas (methane) concentration in goaf holes on the tailgate (TG) side vary between 50 and 75 per cent under the simulated field conditions with flat coal seam gradients. The results also indicated that operation of more goaf holes for draining the goaf gas on the TG side results in high ingress of oxygen and further reduction in gas concentration in goaf gas drainage holes. The simulations also included scenarios with goaf gas drainage holes on the maingate (MG) side, TG cut-through seal and near the start-up area. This paper presents the results of various goaf gas drainage strategies and discusses the effect of various combinations in order to develop effective goaf gas drainage strategies for gas management in start-up areas of the longwall panels.CITATION:Tanguturi, K, Balusu, R and Belle, B, 2015. Development of goaf gas drainage strategies for start-up areas of highly gassy longwall panels, in Proceedings The Australian Mine Ventilation Conference, pp 251–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

Gravity gold recovery has been practiced for thousands of years, making it one of the oldest forms of mineral processing. Gold is 19 times heavier than water although the barren rock is generally only 2.7 times heavier. Any potential gold ore needs to be characterised to assess its amenability to a gravity recoverable gold (GRG) process based on well planned and executed test work. Scale up considerations need to be considered in designing a gravity circuit. The economic impact of a gravity circuit should be justified based on the installed cost and likely benefits. Maximising gravity gold recovery results in a faster cash flow, lower operating cost per ounce and higher overall gold recoveries compared to the several weeks required to recover gold adsorbed onto carbon. The advent of centrifugal concentrators such as the Knelson and Falcon, coupled with intensive leaching of concentrates (ILR), has revolutionised gravity gold circuit designs. Considerations associated with the sizing of the centrifugal machines and the percentage of the circulating load (bleed) that should be processed is discussed in this paper. The trends with gravity circuit layout, engineering, as well as optimum dumping cycles, are important areas which require close consideration. Key aspects of these are presented in this paper. There are a number of circuit configurations to be considered, including the integration of different gravity concentrators. Other gravity process design considerations such as fewer modules, the effect of equipment size and enhancement of process efficiency using preconcentration, together with factors that affect OPEX and CAPEX are addressed. Practical considerations of maintenance, security from theft, minimisation of risk and water balance considerations are discussed using different equipment and circuit configurations. The trend towards using gravity recovery in flotation plants is also reviewed. A number of examples are cited and good design aspects highlighted.

Aug 1, 2010

By S Basu, S L. A Gowravaram

CaF2 has been a common constituent in a wide variety of welding fluxes, including those used for submerged arc welding (SAW). The widespread use of CaF2 stems from its role in lowering the liquidus temperature as well as the viscosity of the molten slag that covers the weld pool. However, the harmful effect of fluoride evaporation from molten flux, on the environment as well as the health of the users is becoming increasingly evident over the years. This has led to increasing attention towards reducing the CaF2 concentration in the fluxes. The fluoride-free formulations face the challenging requirement to maintain the thermo-physical properties (viscosity, liquidus temperature etc) like those observed in fluoride-containing fluxes. In the present work, three fluxes with compositions in the CaO-MnO-SiO2-Al2O3 system have been identified as promising alternatives to the CaF2-rich fluxes. However, the thermo-physical properties of any such flux need to be comparable to CaF2-based commercial SAW fluxes before it can be adopted for regular use. The single hot thermocouple technique (SHTT) has been used by several researchers in the past as a tool for observing the melting and solidification characteristics of fluxes. This device has been developed in the present work and is used to characterise the melting behaviour of the fluxes. The measured solidus and liquidus temperatures from SHTT were compared with the results from differential thermal analysis (DTA) and simulations using the FactSage™ software for a comprehensive understanding. In spite of having a slight deviation in the measured values from the multiple techniques, the results obtained from these multiple methods show that the selected compositions could be potential CaF2 free alternative welding fluxes.

Jun 19, 2024

By S Bourke, R Stone, B Hill

Since Jameson Cell flotation technology was first installed in a coal flotation application in 1988/89 at Newlands Coal Handling and Preparation Plant (CHPP) there have been fundamental improvements to its design which has led to its current status as the leading technology in Australia for fine coal flotation. These improvements, which include key hardware modifications, consist of the re-development of the orifice plate to produce considerable increase in wear life and reduction in power consumption for a given air entrainment and a significant increase in the amount of air that is entrained. Modifications to the downcomer allow maximisation of residence time and air entrainment while changes to the feed and air distribution system allows a reduction in installation cost and a reduction of solids ingress into the air line. Additionally, operational improvements such as the use of recycle to maintain constant flow to the cell feed are discussed. The recent installation at Hail Creek in the Bowen Basin, which consists of three B6000/20 Jameson Cells (6 m diameter bottom-fed distributor with 20 downcomers) will be reviewed as a case study. The latest design and operability of the cells are summarised and compared against one of the original designs at Riverside CHPP also in the Bowen Basin.

Jan 1, 2005

By C P. C David, J P. T Domingo

Addressing nutrient deficiency, among other factors, is vital to the growth and establishment of plants in mine spoils and tailings ponds. Although several organic amendments are available for this purpose, it is important to determine the appropriate ameliorant for the selected plant species. This research examined the effect of different amendments on the growth and ground cover of Centrosema molle, Calopogonium mucunoides and Sorghum spp. in copper/gold tailings. Plant growth and ground cover drastically increased with the application of organic ameliorants, especially manure. Among the three plants, Calopogonium exhibited the best growth and has shown its capability to establish a dense ground cover even in unamended tailings. Results suggest that the plant species and the ameliorants used in this study could be effective in a low-input approach to mine rehabilitation.CITATION:Domingo, J P T and David, C P C, 2014. Legume and grass revegetation of mine tailings, in Proceedings Life-of-Mine 2014 , pp 525–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By S Cyphers, J Missen, B Jansen

The AGL Loy Yang Mine is one of the largest and most significant coalmines in Australia. Commencing in 1982, this mine produces 30–35 Mt/a to supply more than 50 per cent of Victoria’s electrical power requirements. At this mine there are unique geotechnical challenges to overcome to ensure its safe operation including: significant mine depth, low density of coal in the operating and permanent mine batters, the influence of groundwater and deep sediment aquifer pressures. One of the challenges is the behaviour of brown coal, which is neither a soil nor a rock and displays long-term creep stress relief. Other geotechnical challenges include ensuring stability in high unconsolidated dumps, potential large-scale block movement in mine batters driven by crack water pressure and heave from high-pressure aquifers.The paper will outline the geological and hydrogeological setting and potential failure mechanisms, and detail an integrated geographic information system and reporting regime that in part addresses ground control management at the mine. The paper will also outline the management processes for a dynamic geotechnical environment and the benefits of the alliance arrangements to meet the geotechnical requirements at the mine and the effective personnel integration in the mine technical services team.CITATION:Jansen, B, Missen, J and Cyphers, S, 2014. Geotechnical management at the AGL Loy Yang Mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By L Dubron

This study details a mineralogical and textural characterisation of West African iron ores with an emphasis on their behaviour during mineral processing. By means of both qualitative and quantitative characterisation, a simulation of the beneficiation process applied to these iron ores is performed. A series of different analytical tools are used, including:X-Ray Diffraction (XRD) for qualitative mineralogical analysis;• qualitative optical microscopy (phase identifi cation, description of micro-textures) and (semi)• quantitative optical microscopy (counting of particles, phases and textural types); and• chemical analysis.All the information provided by these analytical methods are combined into a quantitative mineralogical and textural analysis, here called ‘modal analysis’, which enables us to simulate the capability of West African iron ores to be benefi ciated by magnetic and gravimetric separation techniques.On one hand, both qualitative XRD and optical microscopy have revealed the presence of the following mineralogical phases: magnetite, haematite, goethite and quartz. On the other hand, the chemical analyses provide us with quantitative inputs expressed as oxides. We have converted the oxides into mineralogical contents expressed as magnetite, haematite, goethite and quartz. In this way, we build a simple quantitative mineralogical analysis.Beside this, the semi-quantitative approach of the characterisation by optical microscopy also provides us with a liberation study, enabling us to split the gangue-bearing content between two types of particles:1. liberated gangue-bearing particles, and2. composite particles composed by both iron (oxhydr) oxides and gangue-bearing minerals.We have assumed that we could anticipate the behaviour of these two kinds of particles through a mineral process, by simulating the removal of at least the liberated particles of gangue. Optical microscopy also revealed a trend in the weathering profi le of the Tokadeh ore horizon with a decrease from bottom to top of magnetite and an increase of both goethite and martite showing a higher level of oxidation and hydration in the upper ore horizon.We have applied this removal extent upon the quartz content of the mineralogical quantitative analysis and we have re-calculated the quantitative mineralogical analysis considering the expected decrease in the quartz content. Finally, by converting the re-calculated (oxhydr) oxides contents into iron grades and summing them, we do obtain a fi nal simulated iron grade for the upgraded products.

Jul 11, 2011

Geological models for the exploration and evaluation of epithermal Au and porphyry Cu-Au deposits rely upon a classification of different deposit styles and an understanding of the evolutionary processes of deposit formation. These models guide the interpretation of subsurface deposit anatomy in order to target drill testing and assist the explorationist to focus on the more prospective projects. It is important for the explorationist to distinguish between different styles of magmatic arc Au deposits as each style displays distinctive characteristics with exploration implications. Magmatic arc Au deposits are distinguished as porphyry Cu-Au formed at depths of 1 - 2 km at the apophysis to larger, buried, magmatic sources which are also the ultimate metal sources for the varying styles of shallower level epithermal Au deposits. Low sulfidation epithermal Au deposits characteristically develop from dilute circulating meteoric waters and are distinguished as the group with a closer relationship to intrusive source rocks, and slightly higher sulfide contents (still generally

Jan 1, 2004

By A Golsby

Both primary and secondary ventilation is important in underground mining. Secondary ventilation refers to the provision of ventilation to development ends, stopes and services facilities, which constitute secondary circuits tapped off the primary circuit or main through flow of air.An unbalanced primary and secondary combination can cause re-circulation, which is inefficient and potentially hazardous. These inefficiencies extend into operational and other considerations, such as power.Most cost justification analysis covers capital and physical consumables. These analyses are often not comprehensive or holistic. This case study is an example of ‘how to holistically justify’ a secondary ventilation circuit and optimise it to meet all stakeholder needs.This paper particularly addresses the following:how to account for all stakeholders in a secondary ventilation cost justificationthe secondary ventilation componentsthe cost justification outcomes and how to measure themsome of the sensitivitiesthe stakeholdershow to present the justification to meet the stakeholder needssecondary ventilation cost justification.CITATION:Golsby, A, 2015. Secondary ventilation as a value proposition – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015