Search Documents

By Kareise G. J, Leung K

The McArthur River (HYC) deposit, located in the Northern Territory of Australia, was discovered by Mt Isa Mines Limited geologists in 1955. It is one of the largest sedimentary stratiform zinc-lead-silver deposits known. Previous attempts to exploit the deposit have been thwarted by its geographical location, the capital expenditure required to establish an operation and the fine-grained nature of the mineralisation. The steeply dipping western margin of the deposit is covered by up to 25 m of overburden, and lies beneath the McArthur River and its flood plain. Dips are eastward, with the eastern edge of the deposit at a depth of about 400 m below the surface. The average thickness of the deposit is 55 m, and it covers an area of about 1.8 by 1.3 km. Seven stratiform orebodies are interbedded with sedimentary breccia, tuff and poorly mineralised siltstone. Mineralisation consists of finely intergrown sphalerite and galena, hosted by pyritic siltstone of the middle Proterozoic McArthur Group. Selective underground mining of the lower orebodies will extract more than one million tonnes of ore per annum. The dip of the mineralisation demands that mining will be by way of apparent dip room and pillar. Declines will provide access and haulage, and wherever possible development will be in ore. Initially, haulage will be by trackless diesel powered trucks, but these will be replaced by a conveyer system. A single zinc-lead-silver concentrate will be produced from a simple flowsheet. This flowsheet has been developed in the laboratory and demonstrated during an extensive pilot plant campaign. A single stage SAG mill will be utilised to grind the ore down to a P80 = 45 ltm (80 per cent of particles passing 45 ¦rn. Conventional flotation cells will produce a single rougher concentrate that will be reground to No

Jan 1, 1993

For Australian mining projects, sustainable groundwater use is typically defined as a groundwater extraction regime, measured over a specified planning time frame, which allows acceptable levels of stress and protects dependent economic, social and environmental values (DEH, 2004). This principle is compatible with most stakeholdersÆ understanding of our national environmental objectives, yet the application of this policy on a project-specific scale is not always straightforward. Three examples of sustainability issues in the management of groundwater in mining are presented. These examples highlight each of the three dependent values: environmental, economic and social.

Jan 1, 2006

By Y S. Zhang

Natural phenomena and human engineering construction activities had great influence on the geosciences space. Natural disasters, particularly mine disaster and other geological disasters happened frequently, which brought great losses both in people’s lives and economics, therefore, to explore the essential causes and mechanisms of disaster by some useful approaches is the most important step in mine disaster prevention. In a variety of methods, building an aground-underground seamlessly integrated model, and then analysing the formation and development mechanism of mining disaster based on this model is a useful way. In this paper, we studied an aground-underground seamlessly Integrated modelling method, and correspondingly given an aground-underground seamlessly integrated 3D spatial model, CSG+CD-TIN+GTP-TTS, by which we can carry out analysis of surface subsidence and underground laneway distortion efficiently, finally preliminary applications verified the effectiveness of this method.

Nov 22, 2011

By M Warnken

Major cities are not only the focal point for AustralianÆs work, leisure and homes, they also are the focal point for the flow of resources into the built environment, motor cars and transportation and urban consumables. The steady increases in æstockÆ and waste generation, in line with GDP growth, means that cities will become the mine sites of the future if the inherent value is recovered from these materials at end of life. The urban waste stream can be characterised as containing approximately nine per cent hydrocarbon-based materials; 57 per cent biomass-based material; 28 per cent fully mineralised materials that are inert, five per cent metals and less than one per cent of problematic materials that are potentially hazardous and toxic. In order to convert these wastes into value added inputs into the economy, a number of technological interventions are required. These æurban waste mining techniquesÆ revolve around source separation and material streaming. One issue that needs to be overcome when determining which mining technique to implement, is identifying the option that will deliver optimal value, both from a financial and a sustainability perspective. The difference between embodied energy and calorific value is a case in point. Highest net resource value (HNRV) is a concept that can assist in choosing between different resource recovery options. The assessment can be done at a strategic level, or can be used to work out material specific issues. For example, used tyres can be recovered for their energy content at an approximate cost of $120 per tonne, whereas mechanical processing of used tyres can deliver a net benefit of $192.

Jan 1, 2006

By E Corpuz, J Weissman, S Winter, R Evans

The surface-to-inseam (SIS) directional drilling technique has been utilised at Oaky Creek Coal for more than a decade to predrain both the Oaky No 1 and Oaky North mining areas. The cumulative drilling program constitutes a total of 140 lateral and 200 vertical holes, and 405 km of lateral drilling.The use of SIS gas drainage has been successful with the following site-specific benefits being recognised:ability to drain German Creek seam gas contents to residual gas levels of new mining areas within an 18-month period from commencement of well productionstructural geological verification of the mine design well in advance of development mining occurring in an areaability to conduct successful predrainage of the overlying Aquila seam to reduce subsequent goaf emissions.Appropriate and up-to-date geological knowledge during the design and drilling process is a significant influence to achieving success. Vertical production wells need to be located in a position that is most effective to remove water from hole. The lateral hole should not include intersections with significant geological structure.SIS drilling provides continuous seam roof/floor data to help define seam geometry and locate geological hazards with high accuracy. In faulted ground and with variable seam gradients, SIS data can resolve geological ambiguities from seismic sections and enhance seam correlation that would otherwise be available only from discrete and closely-spaced infill vertical exploration drilling.Here, we review some examples of SIS configurations and practice to highlight key learnings in drilling long inseam holes (up to 1900 m per arm) ahead of development and mining. Aspects on prerequisites, evolution of network design, tolerances and drainage outcomes in a variety of geological situations are discussed as technical basis towards a viable and effective SIS drilling program.CITATION:Corpuz, E, Evans, R, Weissman, J and Winter, S, 2015. Surface-to-inseam (SIS) drilling at Oaky Creek coal mine – SIS design aspects and drilling environment, in Proceedings The Australian Mine Ventilation Conference, pp 93–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By G M. Mudd

Mine tailings represent one of the two largest sources of mine waste from the minerals industries (the other being waste rock). Given the problems of declining ore grades and growing production, tailings generation is increasing exponentially across the global mining industry. Common practice is for mines to build large containment dams to store tailings during operations, which are then rehabilitated following mine closure. At some sites, however, the controversial practices of riverine or marine dumping of tailings is still practiced. As recent tailings dam failures have shown, there are legitimate questions being raised about the long-term viability of leaving tailings above ground due to the risks of collapse and failure. At present, it is rare for mines to emplace tailings back into former mine voids following mine closure, most commonly into a former open pit mine void (although a fraction of the tailings may be used for underground mine backfill, this is minor in scale). The approach of in-pit tailings has numerous advantages, such as inherent physical stability, low to negligible acid and metalliferous drainage (AMD) risks, as well as allowing more productive use of formerly mined land. In tropical areas where surface repositories are prone to leakage with potential for AMD and widespread dispersal of radionuclides (in the case of uranium mining), in-pit management provides particularly strong advantages – thorough hydrogeological studies are required, however, to address residual groundwater contamination risks and to establish sound, long-term environmental monitoring regimes for groundwater quality and subsidence issues. This paper presents a study of in-pit tailings management and compares it with surface repositories established in a tropical climate. The comparisons lead to the conclusion that, at least under tropical conditions, in-pit tailings management should be considered as world’s best practice – especially for radioactive uranium tailings.

Aug 8, 2011

By R E. Gerald II, B Zhang, T Sander, J D. Smith, J Huang, R J. O’Malley, H Tekle

In the steelmaking process, mold fluxes are essential for ensuring thermal insulation, refining, and the efficiency of continuous casting. Real-time understanding of the in-service composition of slags and fluxes are crucial for optimising the steel production process and improving the quality of the final product. An in situ fibre-optic Raman probe that enables the study of the structure, composition, and viscosity of molten slags and fluxes at steelmaking temperatures has been developed and demonstrated both in the lab and in foundry scale experiments. The focus of this study is on the structural, compositional, and property analysis of molten fluxes in a laboratory setting, with the aim of applying this technology for in situ monitoring during industrial production. Raman spectra were successfully collected at various temperatures from 1000°C to 1400°C in real-time and analysed using a deconvolution algorithm to isolate and quantify peaks in the spectra associated with the specific structures of molecular components in molten and solidifying flux. The research successfully combines in situ Raman spectroscopy with high-temperature viscosity data, specifically targeting CaO-CaF-SiO2-Al2O3 based mould flux systems. Specified ratios of the deconvoluted Raman peaks, such as Al-O-Al/Si-O-Si ratio, shows good correlation with the flux chemistry, while the Q3/Q0 peak ratio shows good correlation with viscosity. A ruggedised Raman probe system was also developed and demonstrated in an 80 kg induction furnace. Ultimately, the goal of this work is to demonstrate in situ slag and mould flux analysis in industrial processes, such as in the continuous caster or electric arc furnace (EAF).

Aug 21, 2024

By R Shelton

The Big Wainihinihi River and tunnel are located on the western side of the Southern Alps of New Zealand within the active Alpine Fault zone, which marks the boundary between the Pacific and Australian Tectonic Plates. The tunnel was built over 100 years ago to supply water for gold mining, but it now conveys water from a high-energy intake to a canal that supplies three of TrustPower’s hydro-electric power stations with a combined installed generating capacity of 10 MW. Part of the tunnel passes through an unstable 50° schist slope, which fi rst suffered a wedge failure in the 1929 Arthur’s Pass Earthquake and was reinstated in the mid-1970s for hydro generation. In 2008, TrustPower’s monitoring system showed that the wedge failure had remobilised and that urgent remediation was required.Harker Underground Construction (Harker) was awarded a design-build contract to restore the tunnel to service by tunnelling a new central section. Their geotechnical engineers, Peters and Cheung, reviewed the tunnel’s stability and proposed a new, safer tunnel alignment, deep behind the failure wedges. This work was based on their failure model, cost-benefit studies, and engineering geology completion mapping at the time of re-opening.Construction innovation was an important factor in ensuring the project’s success, as were detailed geological and geotechnical information, a robust methodology, strong client relationship and planning. To suit the varying rock conditions and restricted space, Harker combined a traditional drill-and-blast method with light-weight modular steel sets and timber supports to reduce construction costs and mitigate support risk. To make material handing easier in the tight conditions, a special electric locomotive was designed and built and blasting confi gurations were adapted to suit varying rock conditions in the highly fractured schist.The isolated site meant interesting and unexpected challenges, particularly communications and resources (both human and material). Despite that, the project was completed within budget, on schedule, and with no lost-time injuries.

Mar 8, 2011

By C Moorhead, J Jones

A common problem in the mining industry is that company geologists can operate in relative isolation to the rest of the company (Jones and Moorhead, 2011). This may result in poor knowledge transfer and often priority conflicts with geology, operations and project departments. This problem is amplified by the acquisition of mineralogy capabilities and other metallurgical (met) test work undertaken by many companies in order to solve for complex orebody problems. Met data is often not located and viewed in 3D space so that geologists and engineers can create and work with geometallurgical (geomet) models (Bye, 2006). Visualisation of data in an interactive graphical 3D model provides a bridge enabling met professionals to collaborate with engineers and geologists to provide a common understanding of the relevance of geomet data.In recognition of this problem, Newcrest has undertaken an effective collaboration strategy to improve internal and external engagement through the use of large visualisation displays (Jones, 2009). The displays are underpinned by IT systems and information management practices that recognise the needs of underlying disciplines. Today it is generally understood within Newcrest that this is required to improve decision-making, deliver faster cycle times and improve governance.Collaboration in companies has been generally associated with the introduction of new IT functions (IBM, 2008). However, the science and engineering process that are used to structure modern IT-based collaboration systems and practices are now known to be simplistic compared to the long-standing practices associated with collaboration and knowledge management in disciplines such as geology and mining.CITATION:Jones, J and Moorhead, C, 2013. Geometallurgical communication as a distributed information system, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 133-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

In classical drill and blast underground mining methods, especially narrow vein operations economic quantities of broken ore can be left behind following normal mucking operations on the stope floors. The ore left behind can have significant economic value and if not collected can be lost forever. This paper reviews techniques for cleaning this material from stopes that have been used in the past and reviews possible modern techniques that can be applied to ensure this valuable material is removed from the stopes.

Aug 1, 2010

By B C. McLellan

The decline of ore grades on land, increasing demand and high prices for various minerals have led to an increased interest in mining the deep ocean sea floor. The potential deep ocean reserves are vast and in some circumstances the grades are high enough to consider mining. However, the consequences of such mining are as yet uncertain. This paper will present the results of a comparative assessment of life cycle impacts of deep ocean minerals. Two alternative extraction technologies from different deep ocean resource types were examined and key commodities are considered. Initial results indicate that the energy requirements will be higher than the average land-based resources, but may fall within the range of the deepest terrestrial mines.CITATION:McLellan, B C, 2015. Comparative life cycle impacts of deep ocean minerals and land-based counterparts, in Proceedings Third International Future Mining Conference, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By C G. Ryan, D R. Cooke

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow-level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-chalcopyrite samples yield a narrow range of δ34 SCDT values (-1.0 to 0.9 ë; n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). Vein quartz from the mineralised zone at Waitangi yields δ18OSMOW values from 6.8 to 12.7 ë (n=23). Fluid inclusion studies indicate a homogenisation temperature range of 190¦ - 296¦C and salinity range of 0.2 - 3.0 wt per cent NaCl equivalent. Similar temperature and salinity ranges have been recorded for the other gold deposits in the Coromandel Peninsula. PIXE (Proton Induced X-ray Emission) analysis revealed that the Waitangi ore fluids have 1090 - 2700 ppm K (average 1600), 145 - 205 ppm Ca (average 180), 80 - 100 ppm Mn (average 90), and 80 - 200 ppm Fe (average 120) but no detectable Cu, Zn, Br, Rb, Sr, Pb and Bi (only one fluid inclusion contains 28 ppm Zn). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source (either directly, or by leaching of igneous sulphides). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1 - 5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in δ18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Mixing of ore fluids with convective ground water is a likely mechanism for gold deposition in a shallow environment for the Waitangi vein system and there is also lack of fluid inclusion evidence (eg liquid-rich and vapour-rich inclusions in the same growth zone) for boiling of ore fluids. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that δ18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1999

By S Hille, J Karageorgos

With the increased variability of todayÆs large-scale mining operations, consistent flotation performance is important to improving and sustaining overall recovery through the circuit. The Newcrest Telfer Mine has implemented advanced process control technology to obtain stable level operation and consistent mass pull in the copper rougher and scavenger flotation circuits. The final result has been an overall reduction in variability, which impacts on both copper and gold recovery. This paper describes the methodology and implementation of the improvements in control at the Newcrest Telfer Mine as being an essential part of the business for minerals processing.

Jan 1, 2007

Maximising margins in today's competitive international commodity markets demands superior productivity. This requires more than simply selecting the best equipment. It requires efficient production and commercial processes together with management systems recognised as international best practice. This paper introduces an integrated way of working that includes management systems for successfully changing work practices and attitudes, developing managers and increasing accountability. It provides an improvement methodology that includes systematic involvement of people in true continuous improvement of processes for maximising productivity and safety while minimising costs. Even though the principles are proven in all industry sectors worldwide, they are not always used correctly. This paper provides examples of traditional performance measurement systems to show how managers miss opportunities to control and improve both production and supporting service processes. It also describes the basic methodology for correct use of the principles and provides examples of correct implementation of modem systems in mining. The charts from actual mining case studies will be elaborated upon in the conference presentation. This paper's main aim is to provide background material for the presentation by introducing integrated principles for building best practice management systems for superior productivity and safety - for higher margins.

Jan 1, 1996

Reduction of Iron Content from Silica by Gravitational Processes In this research work, it was attempted to reduce the iron contents (Fe2O3) in silica sample which was provided from Shenin silica mine using gravitational processes including jig machine, multi gravity separator (MGS), shaking table and spiral. The silica sample contains 93.75 per cent SiO2, 0.44 per cent Fe2O3, 2.78 per cent Al2O3, and 0.08 per cent TiO2 and the Fe2O3 has to be reduced to about 0.1 per cent or less than 0.02 per cent. Mineralogical studies and XRD analysis indicated the presence of haematite, pyrite and goethite as the major iron impurity phases. Mineralogical studies of polished and thin sections yielded that the degree of freedom of silica is more than 80 per cent in the range of -300 +212 mm. After elimination of fine particles, at first nine tests were carried out on crusher product (in two size fractions), wet rod mil product and scrubber product by means of Jig Machine. The best results were obtained with about 0.15 per cent Fe2O3 on rod mill and scrubber product which was not desirable. Thereafter 7 tests were carried out using shaking table; the best results were obtained with about 0.14 per cent Fe2O3 on rod mill and scrubber product which was not desirable. MGS showed the worst result in order to iron removal from silica which was not desirable. Finally 9 testes were carried out using spiral whish is the best gravitational separator for elimination of iron impurities from silica. The best result of spiral tests were achieved on scrubber product. In this test concentrate weight percent and its Fe2O3 grade were 82.32 per cent and 0.085 per cent respectively. Finally a test was carried out using 2 stages of spiral in order to develop flow sheet. In this test concentrate weight percent and its Fe2O3 grade were 78.8 per cent and 0.1 per cent respectively. This product can be used to produce float (clear flat) glass.

Sep 13, 2010

Chlorine as a lixiviant for gold possesses a number of significant chemical and Idnetic advantages over cyanide but because of its corrosive and vaporous nature the method of implementation needs to be significantly modified. At comparable reagent concentrations the dissolution rate for gold in the C12/Cl- systems is some 10 - 100 times that achieved in the 02/CN system. The dissolution rate in the chlorine system is largely a function of the concentration of C12, Cl- and pH. Under conditions of low Cl', (less than 50 g/1), the dissolution rate begins to drop off dramatically over the pH range from 3 - 4. Increasing the level of dissolved chloride ions shifts the pH of this rate reduction to around pH 5 at 100 g/l NaCl, and to around pH 6 at 300 g/l NaCl.

Jan 1, 1991

By C Rothfuss, X Wang, S J. Herbert, K Prasad

The extraction of groundwater to produce gas from coal seam gas (CSG) reservoirs has highlighted the opportunity for beneficial uses of groundwater in Australia. This paper presents an assessment of alternate groundwater modelling approaches that can be used for assessment of one beneficial use option, that of injection. This assessment examines the outcome of the use of different simulation methods on predictions of hydrodynamic behaviour.In this paper, a simplified hydraulic concept of a multi-aquifer system within the hypothetical injection field was used to investigate the hydrodynamic behaviour of injection into the Precipice Sandstone. Comparisons were made through the analysis of a Theis 3D analytical solution with 2D and 3D numerical solutions. The paper discusses the different solution methods and the impact of these on predictions of pressure and flux. Differences in 2D and 3D solutions result in implications if planning injection as a beneficial use of water. For example, the 2D solution resulted in faster and higher injection pressure build-up when compared to the 3D solutions. The 2D modelling could result in either plans that require higher capital expenditure for a greater number of wells in order to spread the pressure effect and remain below the maximum injection pressure or a reduced injection rate. Meanwhile, the 3D modelling with sensitivity analysis could result in planning for lower capital expenditure for fewer wells required to spread the pressure effect and remain below the maximum injection pressure. CITATION:Wang, X, Herbert, S J,?Rothfuss, C and Prasad, K, 2013. Assessment of effectiveness of artificial recharge for coal seam gas water management based on numerical modelling, in Proceedings Water in Mining 2013 , pp 67-72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By S Warden, T Neville, P Leckie

At its simplest, the classification and characterisation of an orebody is a matter of Where, What and When. Where and with what spatial resolution are measurements taken, What properties are measured, and When are the data acquired, processed, and delivered to create the most value. This paper delves into how existing and near-term advances in measurement technologies, field automation, and whole-system-digitisation are combining to open new routes for mine and exploration productivity improvement. Commencing when the initial exploration hole is dug, the advancement in deployment of survey technology—from expert-operated, to driller-operated, to driller-integrated—is used to demonstrate a template for adoption of higher technology measurements. We then introduce and discuss the multi-use measurement as offering outsized returns from a single measurement run, highlighting two new technologies that acquire rock strength while drilling and downhole assay data as examples. For rock strength, we highlight a novel approach to determining Uniaxial Compressive Strength (UCS) while drilling, its relationship to and advantages over Mechanical Specific Energy (MSE), and how it offers utility to multiple downstream processes. For downhole assay, we detail how a back-tophysics approach to Pulsed Fast and Thermal Neutron Activation (PFTNA) analysis offers significant advantages over other measurement methods and earlier implementations of PFTNA, generating a rich data set that can significantly extend and improve the information on which mining decisions are made. Finally, we discuss the possibilities enabled via optimising data delivery, collection, and curation— noting a fundamental limitation of historical systems and exploring the possibilities that will be unlocked by soon-to-market solutions that better enable Orebody Characterisation data to (virtually) move in space and time with rock material post-blasting. Ultimately, the value of optimising the Where, What, and When from point of measurement to the moment it generates maximum value will create greater life-of-asset production for a lower cost and energy input.

Sep 1, 2024

By T Bookless, J Pownell, D Meadows

The ever increasing trend of the gold price has meant that ore deposits that were previously considered too complex, or unattractive by virtue of their low gold grade, are now being investigated more closely. These ore deposits present a greater risk of failure than previously was the case. To ensure that the risk of project failure is reduced and the maximum value is derived from the deposit, its mineralogy, as well as other characteristics, should be well understood such that the optimum process can be designed.Quite often the flow sheet design is assembled using individual process components, from various sources, and without consideration of the complete system. Test work programs require careful planning and an open viewpoint in terms of comminution circuit design particularly with respect to ever increasing power costs across the globe. As an example, high pressure grinding roll (HPGR) technology in many cases offers better mineral liberation than the more traditional comminution devices and it does so at a reduced energy input, and yet HPGR test work is often restricted in its scope due to the perceived novelty of the technology and the resultant lack of generally agreed and accepted test work routes.In this paper the authors outline a typical HPGR test work process route driven by the needs of different ore types and illustrate that to optimise the project value, any test work program should start from the premise that thorough understanding of the ore is vital.CITATION:Bookless, T, Meadows, D and Pownell, J, 2013. Enhancing project value through a designed high pressure grinding roll test work program, in Proceedings World Gold 2013 , pp 291-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P J. Howard

Atlas Iron Limited’s McCamey’s North project lies at the eastern end of the Hamersley Basin, approximately 50 km east of Newman, Western Australia, and 3 km northeast of BHP Billiton’s Jimblebar Mine. The presence of significant surface iron mineralisation identified during field reconnaissance, has subsequently been further defined by detailed mapping and RC drilling.The project area is dominated by outcrops of moderate to steeply north and south dipping banded iron formation, cherts and shales of the Boolgeeda Iron Formation overlying rhyolites and rhyodacites of the Woongarra Volcanics. In lower lying areas recent colluvium and alluvium mask the Archaean geology. Drilling and downhole geophysics has allowed a composite stratigraphic section to be compiled through almost the entire Boolgeeda Iron Formation.Surface orientations and subsurface stratigraphic correlations using natural gamma logs indicate large scale open folding about east-west trending fold axes across the project area; while small scale tight to isoclinal folding with similar fold axis orientations are visible at the outcrop scale. These folds are cut by a number of moderate to steeply south-dipping normal faults defining a series of north-dipping fault blocks which repeat the stratigraphy across the project area.Bedded iron mineralisation consists mainly of haematite-martite and goethite ores with best results of 78 m @ 60.5 per cent Fe. Vitreous goethite is observed at the surface of the mineralised horizons. The mineralisation exhibits a strong stratigraphic control and extend down-dip up to 120 m below surface. The strike extent of the mineralisation is still to be determined. An inferred resource of 39 Mt at 58 per cent Fe has been defi ned to date (ASX: AGO 3 February 2011).The fi ndings at McCamey’s North indicate that there is potential for economic iron mineralisation to exist in other areas of Boolgeeda Iron Formation within the Hamersley Basin.

Jul 11, 2011