Search Documents

By P Collier

From 1972 until 1989 when operations were suspended Bougainville Copper Limited (BCL, owned 53.58 per cent by Rio Tinto Limited) operated a large open pit mine and processing facility at Panguna on Bougainville Island, Papua New Guinea producing copper concentrate containing significant quantities of gold and silver.BCL has a stated vision of recommencing operations at Panguna. In 2008, Rio Tinto, on behalf of BCL, conducted a multi-disciplinary study to assess the technical and financial viability of redeveloping the Panguna operation. One of the key outputs of the study was a Joint Ore Reserves Committee (JORC) Code compliant mineral resource statement based on the existing block model and fundamental data, archived since mine closure. Historical data (including the resource block model and drill hole data) was recovered from computer archives by a former Panguna mine employee familiar with the various obsolete data formats, thus maintaining an unbroken chain of custody of the data by Rio Tinto since operations were suspended. No additional data were collected as part of this study.The extensive data and documentation archive facilitated a sufficiently detailed evaluation of the fundamental data and model to support an updated resource statement. Table 1 of the JORC Code was used to guide the model validation process.Reconciliation of blasthole and metallurgical plant data with the reserve model, indicated that the copper and gold drill hole composite database was significantly biased towards underestimation in several key domains due to a combination of the following: mineralisation loss during core loss, core loss (minor), vertical drill holes failing to intersect sufficient subvertical mineralised fractures and veins, drill hole spacing too wide, and variable diamond drill hole core size. The resource model evaluation was based on three material types (all previously mined at Panguna), that were defined based on cut-off grade and rock type parameters: direct feed ore – material for delivery directly to the plant, preconcentration and screening ore – subeconomic material beneficiated to produce fines of economic grade, and waste. Three pit shells and designs were generated based on three separate sets of economic parameters. These economic parameters were also used to assign material types to the block model. The three resulting models were then evaluated against the corresponding pit shells.Classification of the resource was approached conservatively due to the inherent bias in the drill hole data. Consequently only Indicated and Inferred resources were tabulated.The study highlighted the importance of maintaining detailed documentation pertaining to resource estimates and operational history, particularly reconciliation, and the value that can be added by a simple, low-cost data compilation exercise.

Aug 22, 2011

By S Maritsa, E K. Chiwandika, S M. Masuka

The iron and steel industry is experiencing an increase in the use of iron and steel commodities within societies, decarbonisation pressures, depletion of high iron ore grades and high energy consumption. This necessitates scrap metal recycling, low-grade ore utilisation using the induction or electric arc furnace to achieve the global target of net zero CO2 emission. The available highquality scrap metal cannot sustain the steel industry but the world has unused hematite-goethite ores. It is the aim of this research that this resource be utilised using the induction furnace to sustain the steel industry in an environmentally friendly manner. Indurated pellets prepared from the hematite-goethite ore, 5 wt per cent limestone and 5 wt per cent coal addition were smelted in the induction furnace at 1350 ± 50°C with 25 mins holding time. The effects of basicity and carbon content were also investigated to optimise the smelting parameters. The results showed that the careful control of the basicity, and iron-to-carbon ratio maximised total metal recovery. The optimal basicity ratio was determined to be 1.3 and a carbon to iron ratio of 1.4 achieved a total metal recovery of 73 per cent. The metal recovery was closely related to the estimated slag melting temperature. The basicity ratio of 1.3 achieved the lowest slag melting temperature estimated to be around 1380°C based on the CaO-SiO2-Al2O3 phase diagram. The recovered metal had a comparable chemical composition and microstructure to that products from an ITmk3 furnace.

Jun 19, 2024

By J Wheeler

The objective of this paper is to examine the operation of high frequency screens in closed circuit grinding, where the outcomes achieved indicate favourable economic gains at the comminution stage and downstream processes, including flotation, dewatering, and filtration operations. The classification process in grinding circuits has been slowly evolving within the last century. The history of classification devices brings to mind rake classifiers and spiral classifiers, which although having higher efficiencies compared to hydrocyclones, were not able to keep pace with the evolution of concentrator equipment treating higher tonnages. This higher tonnage throughput has tended to drive the concept of utilising hydrocyclones as the classification stage in closed grinding circuits. The comminution process is commonly the most energy intensive stage of mineral processing. Researchers have determined that the classification stage in the comminution process has the greatest potential for improvement. This paper is intended to inform mineral process engineers of the benefits that high frequency screens offer over hydrocyclones. This will be done by reviewing the purpose for the evolution of classification in the comminution process, documenting past and recent studies, and explaining the modern technology that is currently available.

Aug 8, 2011

By T Goldsmith

The mining industry is cyclical, but those are more than normal business cycles. In the early 2000s the industry saw the start of China as a game changer for the mining industry which lead to catch phrases like ‘stronger for longer’ and even ‘stronger forever’. Enter the global financial crises and the more recent slow-down in the Chinese economy and confidence that the future is bright has dimmed! This paper looks at the long-term forces that are likely to impact the global mining sector and explain why the industry has an excellent future. However, the industry is not without its many challenges and while demand may be in a prolonged step change, the ability to generate profits will depend on the fitness of each asset and company.The author also discusses the hated terms of ‘boom’ and ‘bust’ and considers how the industry can reduce them, but normally exacerbates them. The ability of the junior sector to raise funds being a primary example and one that remains closed to all but the very best exploration assets. There is also consideration of Australia’s position as a mining country in the future world.CITATION:Goldsmith, T, 2014. The future of the global mining sector, in Proceedings Ninth International Mining Geology Conference 2014 , pp 15–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By K Barns, H Law, T Whebell, P Scobie, T Perkins, J Siliezar, M Larson

With processing a variety of orebodies at Glencore’s Ernest Henry Mining (EHM) has come a changing mineralogy and more complex requirements for treatment in the concentrator. From mid-2013 and into 2014 the grind size required to achieve sufficient mineral liberation for production of a quality concentrate has reduced significantly. What was once a final P80 of 35–45 microns was forced to 20 microns. This has necessitated some creative changes to the flow sheet that previously had a 937?kW Vertimill regrinding a rougher concentrate to 40 microns. EHM is able to utilise an existing M10 000 3 MW IsaMill previously used for magnetite processing, to provide a quick convenient solution without large scale capital expenditures. Operating the Vertimill and IsaMill in parallel in closed circuit was successful at reducing the P80 of the regrind circuit to below 20 microns which increased the final concentrate grade by four per cent. This circuit and intermediate circuits used are discussed. Performance of the Vertimill and IsaMill is compared for efficiency optimisation to improve the overall circuit performance.CITATION:Siliezar, J, Whebell, T, Perkins, T, Law, H, Scobie, P, Larson, M and Barns, K, 2014. From magnetite to chalcopyrite – a story of versatility and efficiency at Glencore’s Ernest Henry mining?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Q Gong, J Li, J Zhao, Y Zheng

Excavation by tunnel boring machines (TBMs) offers many advantages over conventional excavation methods, in terms of safety level, working environment, advance rate and overall cost. While TBMs have been extensively used in civil tunnel construction, they are also viewed as a competitive alternative to the drill-and-blast method for underground mining, attracting increasing attention from the mining industry. This paper presents an overview and general assessment on applications of TBMs in mines, by reviewing more than 60 TBM applications in underground/open pit coal and hard rock mines around the world. The projects range from the early exploratory trials of TBMs in mines in Germany, England, South Africa and America in the 1960s and 1970s, to the ongoing projects in Australia, China and Chile. The paper focuses on the geological compatibilities, the problems encountered, the solutions undertaken and the lessons learned from those projects. The paper summarises the progress made in the past and highlights the challenges faced by TBMs in mining due to complex ground conditions and geometrical requirements. With the technological advances of TBM and experiences gained in the past, more applications of TBMs are expected in underground coal and hard rock mines.CITATION:Zheng, Y, Gong, Q, Li, J and Zhao, J, 2014. A review of the applications of tunnel boring machines in mines, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 691–704 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J M. Galvin

The traditional engineering approach to assessing stability is based on comparing resisting force (capacity) to driving force (demand), or strength to working stress. In underground coal geomechanics, considerable effort has been expended on quantifying the strength of rock structures. However, this has not been matched by advances in determining the load acting on these structures, reflecting a reluctance by some to embrace numerical modelling to assess load magnitudes and distributions. Numerical modelling is a valuable aid as loading environments are a function of both the stiffness of the mine workings and the stiffness of the superincumbent strata and are statically indeterminate in most cases.This paper defines stiffness, which is often confused with elastic modulus. It shows that, effectively, stiffness encapsulates geology, depth of mining, panel width, pillar width and mining height. Therefore, these factors are variables that need to be taken into account when determining stress magnitudes and distributions about mine workings. A range of examples are presented that illustrate the significance of the stiffness of the superincumbent strata on surface subsidence; the magnitude and distribution of pillar and abutment load; and aspects of bord and pillar mining, pillar extraction and longwall mining. These examples provide bases for identifying the limitations of some empirical approaches to mine design, identifying how to compensate for some of these in design processes; and emphasising the need to make greater use of numerical modelling in understanding and quantifying loading environments in underground coal mining.CITATION:Galvin, J M, 2014. The significance of superincumbent strata stiffness and its impacts on coalmine design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 3–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By R van Wyk

In today’s mining environment the use of heavy mechanical devices and other high-tech electronic devices like two-way radios, cellular phones and even automated mining systems, form a vital part of the daily operations of a mining site. These human-made devices and some of the naturally occurring events, like lightning and gamma radiation, can have negative effects on electronic detonators and the associated control equipment.On larger mining operations the necessity to move the point of safety for blasting further away from the blast area, introduced remote firing via radio frequencies for electronic detonator systems. Other influences on electronic detonators can be abuse or ignorance. To ensure the safety of the end-user, an electronic detonator must be resistant to some common mistakes that users can make. One of main concerns here is resistance to static discharge or incorrect wiring. Despite the daily use of electronic detonator solutions, scepticism and concern still exists amongst those who believe the system raises the risk of a premature initiation of the blast through some form of interference trigger.This paper will help users understand how electronic detonators and the associated control equipment protects itself from external influences. Focus will be on protection schemes to counter static and over-voltage discharge and methods to ensure protection of secure wireless radio links and detonator communications. With well engineered communication systems and solid static and over-voltage protection, an electronic detonator system can be more reliable and safer than other detonator systems. The following main points will be discussed:what makes a detonator an electronic detonator,static electricity and over-voltage protection,the general influence of electromagnetic energy on the detonator,the influence of lightning on detonators,the protection of radio communication’s links as used by remote firing equipment, andthe safety protection features built into remote firing equipment.

Nov 8, 2011

The Newmont Waihi Operations are centred on the Martha mine at Waihi, New Zealand. The mine has produced over 6.6 million ounces of gold from both openpit and underground sources since operations began in 1878. The current open pit operations commenced in 1988 and in the year to 30 June 2002 produced 129,790 ounces of gold at a cash cost of USD122 per ounce. This paper provides an overview of current operations and future directions.

Jan 1, 2002

By M Bloss, B Roberts

BHP Billiton Olympic Dam required a well-tested software product suitable for strategic optimisation and scheduling of options for a potential underground mining project. The company has a standard software package called Blasor® that is used for open pit optimisation of complex deposits such as iron ore, copper-gold-uranium and silver-lead-zinc. It applies a mixed integer programming formulation (MIP) to produce conceptual pushback designs and an optimised pushback sequence. Schedules can then be run on the resulting mine designs. Existing pushback designs can also be imported into the model and an optimum schedule generated. One of the key advantages of Blasor is that multiple strategic mine schedules can be quickly generated according to the various scenarios, options and constraints that are being investigated.It was realised that Blasor, if carefully configured, could be adapted for use in underground planning. The concept of using Blasor as an optimiser for underground strategic scenarios is to represent the underground stope and development data in the form and structure of an open pit mine. In simple terms, underground stoping areas are modelled in the form of pushbacks (phases) with vertical walls. The phase dependency tools in Blasor are used to link mine blocks and their access development drives. These underground phases are imported into the optimiser. Artificial block models are constructed using stope design tonnage and grade data at various fixed cut-offs. A variable cut-off grade model has also been developed using a method of parcels to represent each cut-off grade increment.So far, this approach has been successfully used to investigate the optimum stope design cut-off for various strategic options, the economic potential of a series of mining and processing configurations and to provide guidance on the optimum sequence for developing and mining the various stoping blocks in the resource. Examination of the results has highlighted the most suitable development paths for more detailed study.CITATION:Roberts, B and Bloss, M, 2014. Adaptation of an open pit optimiser for underground strategic planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 249–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By N Lewis

Recent major urban trunk sewer infrastructure projects in Melbourne have involved construction of nearly 10 km of tunnel boring machine (TBM) driven tunnels in a range of geological conditions varying from soft alluvial soils to hard volcanic rock. To provide both construction and permanent access to the new trunk sewer network, a total of 17 shafts between 5 m and 13 m in diameter, and up to 64 m in depth have been constructed. This paper describes the design and construction of the temporary shaft support systems for the shafts.The range and variability of geological conditions at each shaft site required the adoption of the following shaft support systems across the projects – jet grouting, sheet piles, diaphragm wall, secant pile, contiguous pile, reinforced shotcrete rings and rock bolts.Groundwater control, settlement, TBM launch and reception chambers at the shaft base, chambers and TBM launches at mid-depth of shafts, connection shafts between new and existing sewers and bypass pumping shafts are among the challenges that have been met.This paper reports on the some of the challenges involved and experience gained in developing design and construction solutions for large diameter shafts that are excavated within varying geology in Melbourne over the past three years.

Mar 8, 2011

By J Franz, S Bock, N Hentrich

Artificial ground freezing is the unrivalled method for groundwater control during mine shaft sinking. Moreover, ground freezing may also provide temporary ground support. The fast development of fibre-optic temperature monitoring devices, three-dimensional freeze pipe survey methods and numerical modelling software provide grounds for developing new and reliable tools for ground control during freeze shaft sinking. This paper presents examples of predictive numerical models that are based on back-analysis and calibration of temperature data that covers the complete construction cycle from pre-freezing through to artificial thawing. The back-analyses showed that standard numerical models are not capable of predicting the prevailing thermo-mechanical conditions satisfactorily. This paper describes the development and implementation of new tools for improved consideration of concrete hydration and latent heat, along with the introduction of other algorithms that improve and simplify the efforts of managing complex numerical models. A function is presented that allows for an automated correction of the model’s mesh based on results of three-dimensional freeze pipe surveys. This paper demonstrates that the latter consideration is important, because the often employed assumption of idealised freeze circle geometry in numerical models impacts on the accuracy of such model’s predictions. Subsequently, the verification of these extended numerical models is demonstrated. Due to its flexibility, the FLAC3DTM code was employed for the numerical modelling. This software provides the possibility of implementing additional functions written in internal FISH or Python language into the models. It is concluded that state-of-the-art techniques for freeze hole drilling and surveying, on-site monitoring and advanced numerical analysis provide a significant potential for both the design and the operation of largescale ground freezing measures. The application of the extended numerical models for predictive simulations during construction allows for temporary shaft lining optimisation, for assisting in operational decision making and for compensating temporary loss of monitoring data. Suggestions are made for required future work in order to further improve the developed ground control tools. CITATION:Bock, S, Franz, J and Hentrich, N, 2018. New tools for ground control in freeze shaft sinking, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 393–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

By P Kittler

In the spectrum of mining-related disciplines, geometallurgy sits between resource geology and metallurgical engineering. Unlike its neighbours, it is a relatively young discipline and its concepts, procedures and techniques are still evolving. Relevant geometallurgical issues differ from one deposit to the next so there is no single template that can be used in all situations, meaning that geometallurgy programs are nearly always customised and tailored to the deposit and the situation.Over time, a number of key mistakes are seen to emerge regularly. The eventual impact of these mistakes can vary from suboptimal performance of mine and plant to complete failure of the operation. For instance, poor characterisation of ore lithologies and their spatial distribution can have negative impacts on processing plant throughput. However, when combined with failure to identify critical blending constraints it can result in a totally inoperable plant.A number of common mistakes committed during geometallurgical programs are discussed and some preferred alternative approaches are suggested

Sep 5, 2011

By K Jupp, T J. Howard

Cliffs Natural Resources Pty Ltd (CNR) operates iron ore mines in the Koolyanobbing region of Western Australia. Ore is mined from three locations, separated by many kilometres. The ore is stockpiled at these locations, according to an in-house ore classification system (based on grade and source) and then trucked to the crushing and screening plant at Koolyanobbing. Lump and fines products are railed to Esperance for ship loading and export to Asian customers. CNR prides itself on the relatively low inter-shipment grade variability of the products. The Koolyanobbing crusher is fed using a daily blend plan, generated to maintain lump and fines product grades within acceptable tolerance ranges around targets. Achieving low variability requires predicting lump and fines grades as accurately as practical from the estimated head grades of the ROM ores potentially going into the blend. The grade prediction model may be either a direct prediction of crushed lump and fines grades and lump percentage, or be split into two stages: the bias between blasthole estimated head grade and crusher head grade and then the lump-fines algorithm for splitting the head grade between lump and fines products. The lump-fines algorithm comprises the percentage of lump and the difference between the lump and fines grades. We describe a weighted least squares (WLS) regression model for predicting crusher grades and lump proportion from the estimated head grade for Fe, P, SiO2, Al2O3, Mn and S. The method is applied to CNR production data, where the regression model explains approximately 60 per cent of the variance in the crushed ore grade, for both lump and fines. A further small but significant improvement in prediction can be achieved by including the ore classification data in the model. The regression errors exhibit strong positive serial correlation, indicating trends in grade error across multiple blend records. To compensate for the longer-term error, an exponentially smoothed model was developed and applied to the daily grade blend errors. This gave an increase in the longer-term variance explained and therefore an improvement in grade prediction.

Jan 1, 2009

Process mineralogy is an inter-discipline in the fields of mineralogy and mineral processing. As a predicting and trouble-shooting tool, process mineralogy helps address all mineralogical issues and problems related to mineral processing. It provides useful information on process design and optimisation, flow sheet development and cost reduction. As more and more complex and refractory ores are being discovered and processed, it is believed that process mineralogy will gain more attention and play a more important role in process design and optimisation. This paper will first discuss the scope of process mineralogy and mineralogical factors that may affect mineral processing of various ores, and then focuses on the application of process mineralogy in process design and optimisation through case studies.

Jan 1, 2008

By A B. Jahed, Ö Aydan, T Ito

In this study, the authors compiled some case history data and present some typical examples of rock slope stability issues in Afghanistan with a special emphasis on Kandahar region and categorise rock slope failures according to the principles of modern rock slope engineering. The slopes considered involve rock-cut, natural rock slopes mainly. The effect of structural geology and discontinuous nature of rock mass on both slope-cuts and natural rock slopes is taken into account and some preliminary assessments on the stable and unstable rock slopes are presented. Furthermore, the seismic effect on their stability is also considered. It is also pointed out that similar issues could be observed in open pit mines, which may be exploited in years to come.

Nov 29, 2022

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M J. Gillespie, P D. Erskine

Mine site rehabilitation generally includes the re-shaping of overburden to create a final landform, manipulation of substrates and subsequent revegetation. Due to the wide range of environmental variables that influence rehabilitation progression, having clearly-stated final land-use goals and ongoing significant contributions to the planning process, from prefeasibility through to mine closure, is essential for achieving stable landforms and sustainable rehabilitated communities. Two examples of rehabilitation processes in the phosphate rich region of North West Queensland are used to illustrate some of the possible benefits of early planning and communication of rehabilitation requirements.Approximately 160 km south of Mount Isa, Incitec Pivot Limited operates a 35 year old open cut mine at Phosphate Hill. Monitoring of rehabilitation areas and selected analogue sites is undertaken annually, but the initial landform design, substrate management and species selection has created a difficult environment for revegetated areas to successfully establish. Constant management input (such as weed management, erosion control, supplementary seeding, etc) will, therefore, be required over a long time frame.The second example uses exploratory drilling and historic costean pits at Legend International HoldingÆs Paradise South site, 135 km north of Mount Isa, to determine the success of natural vegetation colonisation on waste rock and compacted soils, and the effects of cattle grazing on recolonisation. This information can be used by planners of the mine life to inform possible end-land use decisions and proposed completion criteria.In a semi-arid environment such as North West Queensland, the creation of a post-mine landscape suitable for nature conservation and/or grazing can be an arduous task. The input from environmental personnel at all stages of the mining process will positively impact upon the quality of the resulting rehabilitation and ensure undesirable legacy issues are minimised.CITATION:Gillespie, M J and Erskine, P D, 2012. Importance of early rehabilitation planning - Case studies from North West Queensland, in Proceedings Life-of-Mine 2012 , pp 187-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By S Bluhm, R Funnell

Creative mine-designs are constantly being applied in the deep platinum mining industry in South Africa. Recently, this has resulted in deep hot mine-designs including room and pillar, bord and pillar or stall and pillar layouts and the use of in-stope trackless mechanisation. In these mines, the ventilation systems use refrigerated air and high fan pressures and as a result ventilation leakage can have a huge impact. Leakage is a serious impediment to cost-effective operation and potential leakage in future projects is a major factor in judging project viability. This paper describes certain mine layouts and quantifies the extent of the leakage. Based on typical field data, a range of seals from ævery poorÆ to ævery goodÆ was defined and used to estimate overall leakage. Within these mine networks the ventilation pressure, temperature and density all vary significantly and with the multiplicity of leakage paths it was necessary to make use of the VUMA-network simulation package. For the examples examined, the leakage was found to be up to 85 per cent for æpoorÆ category seals and up to 50 per cent for ægoodÆ category seals. The total air flow (and refrigeration) requirements grow exponentially with strike distance due to the compounding effects of higher pressure and more leakage paths. It is shown that beyond certain depths and strike distances the leakage will become so great that it will be impossible to operate cost-effectively û even with ægoodÆ seals. Indeed, in these examples the projects were not considered viable in their original format because of the high ventilation-cooling costs and the mine-designs were modified to include footwall drive systems û the cost of which was justified by the reduced strategic risk to operating ineffectiveness due to leakage.

Jan 1, 2005