Search Documents

By I Warren, M P. Simpson

Adularia-sericite epithermal ore deposits have well-documented alteration mineral zonation patterns with distinctive geochemical signatures. Proper use of whole-rock geochemistry can provide useful vectors for exploration and can enhance efforts to characterise and quantify the mineralogy and intensity of hydrothermal alteration.   Analyses of Au and Ag provide the most direct vectors to orebodies, and pathfinder elements such as As, Sb, Hg, Zn, Pb and Se are similarly zoned around at least some orebodies. However, the minerals that contain these elements occur almost exclusively in veins, and therefore identifying geochemical vectors related to wallrock alteration that is zoned outward from orebodies is crucial for effective exploration.   Distal alteration zones contain quartz-illite-chlorite-carbonate-pyrite, whereas samples proximal to veins contain quartz-adularia-pyrite, with lesser though variable illite-chlorite-carbonate. Therefore, adularia-sericite epithermal ore deposits show K alteration in their cores. The resulting K-metasomatism can be evaluated in several ways. Areas that have been most intensely altered are commonly characterised by highest K contents, but these results can be complicated by variations in rock type across the prospective area. Potassium mass balance results provide a robust and rigorous assessment of K-metasomatism, however, knowledge about the composition of fresh rocks and correct identification of fresh precursor compositions of altered rocks are required. Three alteration indices provide effective evaluation of K-metasomatism: 1.   the K number, which is the ratio K/(2Ca+K+Na) (molar); 2.   Barrie values [(K2O * 100) / Sr]; and 3.   the Rb/Sr ratio. In most places these provide similar vectors, although K numbers can be complicated by the appearance of hydrothermal calcite and/or albite.   Plots of K/Al vs (2 Ca + K + Na)/Al (molar) allow estimation of the intensity of K-metasomatism and its mineralogical products, thereby complementing traditional XRD and petrographic studies of alteration minerals.

Jan 1, 2005

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By H Bao, M Nehring, M Kizil, P Knights

The mining sector, a notably energy-intensive industry worldwide, is a major consumer of fossil fuels, leading to significant carbon emissions globally. The move towards electrification, coupled with advancements in battery technology, has redirected focus from traditional diesel-powered solutions to battery-powered alternatives. This paper introduces a novel mining haulage system, termed the Battery Trolley system, and examines its theoretical foundations, configurations, and operational processes. It offers a comprehensive analysis of the system’s characteristics and limitations. Through a hypothetical road simulation, the study analyses various battery mining trucks, calculating energy consumption based on force parameters and tailoring battery sizes to contemporary materials and technology. When assessing various battery truck alternatives—considering aspects such as battery size, effective payload, duty cycle, energy efficiency, productivity, and single-shift production—a range of performance outcomes and characters become apparent within the mining context. The findings indicate that Battery Trolley configurations, requiring smaller battery capacities, entail lesser compromises on effective payload. Consequently, these configurations achieve a higher duty cycle, reduced energy consumption per tonne, heightened productivity, and enhanced singleshift production capabilities compared to Battery-only alternatives. The comparative analysis of Battery Trolley with stationary charging (BT-S) and Battery Trolley – dynamic charging (BT-D) underlines that battery Trolley systems are capable of overcoming the challenges associated with battery size, thus successfully fulfilling the production demands of large truck applications in mining. This positions Battery Trolley systems as a more advantageous option for the decarbonisation of mining fleets, underscoring their potential in contributing to the sector’s sustainable evolution.

Sep 1, 2024

The lignites of Otago and Southland offer a potentially viable future feedstock for electricity production and possible conversion to petrochemicals or liquid fuels. The deposits, when combined, represent New ZealandÆs largest energy inventory; equivalent to about 74 000 petajoules û or approximately 35 times current natural gas reserves. Too often dismissed as irrelevant to New ZealandÆs energy future because of adverse perceptions of the value of low rank coals, the strategic value of this resource is in fact huge.   Investigations of the lignites extend back over more than 50 years (LFTB various, CRL Energy Ltd). Whilst it is not the intention of this paper to review this work, these investigations have confirmed the suitability of the resource as a feedstock for thermochemical conversion. Current estimates of South Island lignite mining costs are NZ$1.0 - 3.0/GJ (Natusch 2005), making these resources amongst the most competitively-priced energy sources available world-wide.   This value, however, will only be captured if we as a country begin to envisage a world-scale, long-life, integrated and multi-faceted development sized to supply world markets for chemicals or fuels. Recent CAE studies (Hooper and Riddolls, 2005) have emphasised the vital importance of ensuring that any exploitation of this resource maximises their value to New Zealand. The question that thus must be applied is how might large-scale utilisation of the resource fit with New ZealandÆs primary energy supply, and its potential for the export of high-value commodities.   From the broader perspective of New ZealandÆs total energy supply equation we need to examine other supply options beyond just the generation of electricity. We face in this country a situation wherein almost all our liquid fuels feedstock has to be imported with projections for an increasing dependence on imported oil. In addition NZ has a natural gas reserves-to-production ratio of less than ten years, and dwindling supply from local production. Without further natural gas discoveries, New Zealand has only a window of approximately five years before we will need to commit to imported LNG or some other thermal fuels option.   In other words, New Zealand is facing an uncertain future unless we can restore energy inventories to cover an adequate strategic reserve capacity as well as enable long-term investment in alternative sources. Within this context the South Island lignite resources are thus deserving of more attention. The extent of the resource is well known, its suitability for conversion reasonably assessed, and its magnitude such that there is little doubt that lignite conversion could adequately meet NZÆs future energy needs for many years out.   This paper reviews coal gasification technology, its application to lignite and the possibilities for future development of the lignite resources. It is argued that the strategic imperative for this country is to secure the lignite resources as a primary energy source for this country well into the latter half of this century.

Jan 1, 2005

By M Wortley, J Korteniemi, D La Rosa, L Rajavuori

Geometallurgical modelling of an orebody provides benefits to a mine by gaining a better understanding of the ore characteristics and how they affect the performance of the concentrator. With this knowledge, plant operating conditions can be adjusted to optimise throughput and recovery in advance of the arrival of particular ore types. Therefore, it is extremely important that the origin of the ore being processed is known as accurately as possible. Depending on the homogeneity of the ore characteristics, reliance on assumptions about stockpile residence times, scheduling and material handling can render the best geometallurgical models useless.The solution adopted at Agnico Eagle’s Kittilä mine was to utilise Metso SmartTags™ and in-house expertise to develop a system that continuously and accurately links geotechnical and lab data from the mine to the performance of the plant. This application presented several unique opportunities and challenges. For example, this was the first installation of a SmartTag™ system for geometallurgical modelling in an underground mine. Challenges included the fact that the system installation is routinely subjected to temperatures below -20°C.The system was installed and commissioned in early 2013 and has been operating continuously since. Kittilä has begun to see the benefits of the system, with an increased understanding of how different ores are processed in the concentrator. Other advantages include the ability to alert operators about the arrival of difficult ores and a better understanding of the ore handling systems.This paper describes the installation and use of the system at Kittilä and details some of the geometallurgical relationships that have been developed using the data collected so far.CITATION:La Rosa, D, Rajavuori, L, Korteniemi, J and Wortley, M, 2014. Geometallurgical modelling and ore tracking at Kittilä Mine, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 291–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Zhou, L Crompton, K P. Galvin, J L. Sutherland, C P. Lowes, C Bezuidenhout, J Bijzet

Platinum Group Metal (PGM) bearing ores from the Upper Group 2 (UG2) reef often contain significant concentrations of chromite which can potentially be upgraded to produce a saleable product. A common approach is to implement gravity separation on the PGM flotation circuit tailings. However, where the particle size range of interest is broad and the lower size limit ultra-fine, the challenge is how to maximise the recovery at a saleable product grade without compromising throughput. This study was concerned with the performance of a REFLUX™ Classifier for beneficiation of a PGM bearing chromite ore and the benefits of size classification. The sample had a nominal top size of 0.5 mm and was processed over the complete size range and in two discrete size classes following classification at 106 µm. The primary goal was to produce a concentrate exceeding 40 wt. per cent Cr2O3, ideally approaching 42 wt. per cent Cr2O3, with minimal PGM losses above 106 µm. A major challenge was to process at the required solids throughput in a single stage with the feed pulp density constrained to a nominal upper limit of 30 wt. per cent solids. It was found that varying the controller density set point of the REFLUX™ Classifier produced strong control of the product grade. Products as high as 41.1 wt. per cent Cr2O3 were produced at 78.6 per cent recovery for the +106 µm material, while in the −106 µm portion the product grade was as high as 41.4 wt. per cent Cr2O3 at 83.2 per cent recovery. Processing the feed in discrete size classes enabled the volumetric feed and fluidisation rates to be optimised for a given application; hence, superior performance was achieved at the finer sizes. This work has demonstrated the value in considering feed preparation as well as technology selection in developing a robust process solution.

Aug 24, 2022

By M Hawkins

The Clem Jones Tunnel (formally known as the North-South Bypass Tunnel), a A$2.88 billion road tunnel project in Brisbane, Queensland, was successfully completed almost seven months ahead of schedule. The project included two parallel 4.7 km long road tunnels, 740 m of intermediate roadway access ramps and two auxiliary ventilation tunnels. The tunnels incorporate intelligent tunnel systems, best practice fire and life safety standards and typical civil tunnel elements.Over the duration of the project the Parsons Brinckerhoff (PB) and AECOM (formally Maunsell) design joint venture (MPB) were Lead Designers to the Leighton Contractors and Baulderstone Bilfinger Berger Joint Venture (LBBJV). Construction of the toll road commenced in September 2006 and was completed in March 2010, with the tunnel opening then. Contributing to the success of this project was the continued support the lead designers gave throughout the construction period.This paper will focus on some of the structural elements that contributed to the success of the project – in particular the cable tunnel structure, a small precast, culvert shaped element under the pavement of the mainline tunnel, and the fit-out of the Gibbon Street shaft which were designed to be constructed in a combination of precast and in situ concrete.The cable tunnel was incorporated early in the design phase and runs the length of much of the tunnel. This paper will outline the challenges faced by the designers with implementing this system which provided significant construction advantages, among which were being able to install a separate ventilation duct during construction and to start fitting out the mechanical and electrical conduits and drainage system while tunnelling was still underway.The Gibbon Street shaft had a length and width of 20 m by 40 m and an overall depth of 38 m. A 20 m high structure of precast and in situ concrete was constructed in the base to accommodate mechanical and electrical equipment and provide a take-off access for the southern ventilation tunnel. The construction purpose for this structure was to provide a junction between the tunnel boring machine (TBM) and the roadheader-style tunnels, a staging platform for commencing the roadheader tunnelling, and a platform where the TBMs could be dismantled and removed.The design was assessed and reviewed many times throughout the construction process to address the needs of each of these stages. Innovative use of precast concrete was used to minimise construction time.Additionally, the designers provided support to the construction team from the time of design completion through to the tunnel opening. This meant that the changes to the design and adjustment of construction loadings could also be assessed. The fi nal outcome resulted in an efficient construction sequence and a project that has provided an excellent outcome for the client, stakeholders and community.

Mar 8, 2011

By L Mollison, K W. Mills, N R. P Baczynski, M F. Lee, I A. de Bruyn

This is the first of two papers concerned with rock stress inputs to various mine design issues at the large Ok Tedi open pit mine in Papua New Guinea. The companion paper (also published at this conference) is ‘The Application of Rock Stress Inputs to Stability Assessments at Ok Tedi Mine, Papua New Guinea’ (de Bruyn et al, 2014).Stresses are a required input for numerical modelling of mine design issues. However, for some operations, like the very large Ok Tedi open pit mine in remote rugged mountainous terrain, direct and representative measurement of rock stresses can be technically difficult and expensive. In such situations, development of an appropriate and sufficient understanding of rock stresses can be challenging.This was addressed for Ok Tedi by considering the following:The tectonic and regional geologic setting of the mine.Results from three different programs of rock stress measurement over 19 years, including hydraulic fracturing (1991), acoustic emission (2007) and overcoring (2010). Some interesting results of the overcoring work are discussed. It was done in a 4 km long drainage tunnel, which intersected a thick monzodiorite intrusive that has metamorphosed contacts to host contact Ieru Formation siltstones; anomalously low horizontal stresses were measured within the monzodiorite.Compilation of rock stress measurements from other New Guinea mines and prospects, both in Papua New Guinea and Indonesian West Papua.Comparisons between the variable Ok Tedi rock stresses and similar data from other porphyry copper deposits.CITATION:Lee, M F, Baczynski, N R P, Mills, K W, de Bruyn, I A and Mollison, L, 2014. Rock stresses at Ok Tedi, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By S S Solomons

In 1991 the uranium spot market price dropped to approximately US$7/Ib U308, a historical low in real terms and the short-term outlook for the industry in the next five years was grim. At this time the Ranger operation was producing uranium concentrate at its design capacity of approximately 3 000 tonnes/year. The loss of two major long-term contracts owing to price and reduced power utility demand due to excess inventories meant that the company could not match production to sales. Continuance at this production level would have resulted in a rapid buildup of product inventory and the tie-up of significant cash reserves. After analysing various options, an innovative operating strategy was devised such that production and sales were approximately balanced without a significant impact on the unit production cost or a long term effect on the plant or operation. A campaign mining/milling operation commenced and approximately 40 per cent of the workforce were retrenched. Multi-skilling of all employees was a critical aspect of ensuring a successful outcome. This paper examines the strategy and reports on the success of the operation two years after the restructuring exercise was effected in November 1991.

Jan 1, 1994

By S C. Dominy

Gravity amenable gold ores are those that after comminution produce liberated particles, composites and/or carriers that can be recovered by gravity separation means. Recovery depends upon mineralisation type and the comminution and concentration method used. Any in situ ore with more than 20 per cent of gold greater than 100 µm in size is likely to have a strong gravity recoverable component. A less traditional approach is where the gold is sulfide-locked and the gold carrier plus any liberated gold is recovered via continuous gravity recovery following fine crushing. Specific tests are undertaken to determine the level of gravity amenable gold within a deposit. The principal methodology is the gravity recoverable gold (GRG) test, which consists of three sequential liberation and recovery stages. For continuous gravity recovery (CGR), the sample is fed over a laboratory Wilfley table to simulate continuous recovery of the gold. Tails from the feed can be progressively re-ground and re-tabled to develop a grade-recovery curve. Primary geology and gold particle size-distribution have a strong effect on the mass of sample required to provide representative results for both tests. Where low-grade ore contains very coarse gold, substantially larger sample masses are required. Experience has shown that GRG and CGR values can vary throughout an orebody, particularly within different geological-grade domains. A testing regime must consider sample frequency and support.

Sep 5, 2011

By T Angerer, N H. Maund, S Hagemann, D R. Cowan

Cliffs Natural Resources Pty Ltd - Asia Pacific Iron Ore's (formerly Portman Iron Ore Limited) K deposit (Dowd's Hill), at its Koolyanobbing operation in Western Australia, hosts enriched magnetite mineralisation below the presently mined haematite-goethite ore zone. Two distinct northwest-southeast elongated, highly magnetic anomalous bodies that dip to the north-east appear to be sourced by this deeper mineralisation. Magnetic modelling indicates significant remanent magnetisation with Qratios around 1.5, directed shallow down. The north-west anomaly is overlain by a ridge of uneconomic banded iron formation (BIF) and the present waste dump, whereas the south-east body was partly exposed during ongoing mining of overlying haematite-goethite ore. Sections of the magnetite mineralisation in this south-east anomaly were intersected previously by diamond drill holes. Review of the historic cores identified potential magnetite enrichment, with grades and mineralogy that might be amenable to beneficiation. A first-phase reverse circulation drilling program was designed to further delineate the trend and extent of the two anomalies. The following magnetite mineralisation assemblages are recognised from cores, reverse circulation (RC) drill cuttings and pit mapping of the south-east magnetic body: higher-grade magnetite-haematite ¦ goethite and magnetite ¦ pyrite and lower-grade, recrystallised magnetite-quartz (BIF), magnetite-carbonate, magnetite-talc and minor magnetite-bearing mafic schist. Disseminated specularite is locally present in theassemblages. Talc-schist and massive pyrite occur along the footwall contact. Magnetic susceptibility measured from drill chips within the magnetite-enriched zones reveals an apparent susceptibility values range of 0.2 to 1.3 SI. Preliminary results from Satmagan and Davis tube recovery analysis shows that the magnetite content in these mineralised zones correlate well with existing geophysical data and magnetic susceptibility measurements.

Jan 1, 2009

By S Gossmann, J Barlow, S Denner

"Unconventional gas resources, including coal seam gas (CSG) reservoirs, can be located above and below aquifers that provide groundwater for agricultural, industrial, urban and other uses. Development of these resources may, therefore, lead to potential impacts on groundwater supply.Management of reservoir/aquifer interconnections necessitates a program of focused data acquisition. For example, groundwater transfer from shallow aquifers to underlying CSG reservoirs may occur where CSG-containing units subcrop beneath shallow aquifers, possibly at significant distances from operating wells.Arrow Energy is undertaking studies of connectivity between aquifers including an investigation in collaboration with the Queensland Office of Groundwater Impact Assessment to evaluate connectivity between the Condamine Alluvium (CA) and CSG-containing Walloon Coal Measures (WCM).The Condamine Valley hosts highly productive agricultural land with groundwater resources heavily utilised for irrigation. Water demand outstrips available supply and groundwater has been subject to restrictions on further development since the early 1970s. Developments that could have an additional impact on groundwater resources in the CA are of major concern to local landholders. This paper describes: planned field investigations at two sites: 1. Stratheden, where pumping from the WCM will be undertaken 2. Daleglade, where pumping from the CA will occur how the data to be collected from field investigations will be used to refine predictions of flux between the CA and the WCM.CITATION:Denner, S, Gossmann, S and Barlow, J, 2013. Planned field investigation of connectivity between the Condamine Alluvium and Walloon Coal Measures, in Proceedings Water in Mining 2013, pp 91-98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By J Rutter, D Francois-Bongarcon, M Federov, N Odiar, M Scott

There are two fundamental methods for metalliferous sensing of primary crushed ore available for deployment at operations. These methods can be classed as surface measurement techniques (including XRF, LIBS, NIR, SWIR) or penetrative/semi-penetrative measurement techniques (including PGNAA, PFTNA, GAA, MR). While the individual sensing technologies exploit different physical phenomena to measure metal content, penetrative sensor measurements of grade are often regarded to be superior to surface measurement techniques due to the much larger sampling volume penetrative techniques provide. Surface sensing techniques often utilise simpler, established technologies that have considerable benefits in the speed of analysis, capital costs, ease of deployment, social license to operate and operational safety. This paper investigates whether surface sensing techniques achieve adequate sampling representativity of primary crushed rock mass to provide economic benefit over penetrative sensing technologies for bulk ore sorting applications. The paper details the methodology used to assess whether surface XRF measurements change throughout various stages of comminution, and increased surface exposure, from primary crushed ore (top size of -175mm) to finely crushed product for assay (top size -2mm). The methodology was applied to 2 ore mineralisation styles, across variable metals and grades, to identify any associated opportunities and limitations to surface sensing techniques. The results assist in developing a method to determine if surface sensing and measuring via XRF is an adequate representation of the rock mass for bulk ore sorting applications and identify any associated limitations in particle size distribution, mineralisation or natural deportment strength to guide suitable application of surface sensing techniques.

Nov 10, 2020

By M Camarda, A Pirson, F Vasconcelos, J Mesquita

ArcelorMittal Prijedor is a goethitic iron ore mine located in the north-west of Bosnia and Herzegovina, which mainly supplies ArcelorMittal’s European subsidiaries. Annual production of the asset stands at the level of 1.5–2.1 million tons of iron ore product which is sent to ArcelorMittal Zenica steelmaking plant. Two types of products with approximately 50 per cent Fe are generated in Prijedor through a process composed by crushing, screening, and magnetic separation stages. Within this process one of the tailings produced is called ‘ultrafines’. The ‘ultrafines’ product corresponds to the desliming hydrocyclones overflow in Prijedor plant, which is classified in a size fraction below 25 μm and corresponds to about 5 per cent of feed. This material is richer in iron than the coarser size fractions of the ore but do not present a good performance in concentration processes. In this way, several studies have been carried out during the last years to find solutions to use the ‘ultrafines’ material without success. In this context, the possibility of dehydroxylate the goethite contained in the material transforming the mineral into hematite and thus increasing the iron grade of the final product was investigated. During the research, several dehydroxylation tests with different temperatures and time of exposure were performed. Using dihydroxylation process at temperatures higher than 800°C it was possible to produce a material with 43 per cent Fe from the original 39 per cent Fe ‘ultrafines’ sample. In addition, the dehydroxylation tests confirmed that goethite becomes completely transformed into hematite at 400°C (with an exposure time of 60 mins) and material is completely sintered at 1200°C. A simulation study based on dehydroxylation tests results showed that it would be possible to use a ‘ultrafines’ product with Fe grade higher than 45 per cent to produce a material with 50 per cent Fe through a complete dehydroxylation process.

Sep 18, 2023

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

By I D. Gregson, A Gandhe, A S. Garcia, K M. MacAndrew

"Falls of ground still cause around one-third of all underground mining fatalities. The recent introduction of mechanised room and pillar working into Indian coalmines is an example of the application of new design by measurement and safety monitoring strategies, which can be used to reduce falls of ground risks in mines.Rock Mechanics Technology, now part of Golder Associates UK Ltd (Golder), is providing rock bolt support and pillar design services to the mines using a design by measurement approach. This involves in situ monitoring to confirm support and pillar designs and pillar extraction sequences.Site examples are given of the support designs determined and the monitoring programs undertaken for both design and safety.Routine safety monitoring of roof movement using telltales is also described. A new auto warning telltale has been developed specifically to warn of imminent caving as pillars are extracted.The approach used by Golder has played a major role in ensuring the success of these projects. As a consequence, mechanised room and pillar working is now firmly established in India, and wider application is planned to help meet future demand for coal.The experience confirms that the design by measurement method for this application has important advantages over conventional design approaches using analytical or empirical methods. Firstly, it measures the design performance or outcome rather than trying to calculate or predict it. Secondly, it provides the opportunity for the design to be adjusted to obtain the optimum outcome. Thirdly, it can do this at a local level, so that the support design can be matched to changing conditions to give the most cost-effective design. Finally, it incorporates long-term monitoring of support performance, again at a local level, so that subsequent change can be identified to enable corrective measures to be implemented in a timely manner and to ensure that ground control safety is maintained.CITATION:MacAndrew, K M, Garcia, A S, Gregson, I D and Gandhe, A, 2014. Application of design by measurement for support and pillar design in mechanised room and pillar coal mining in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By M Revell, B Sainsbury, D Sainsbury

This paper extends the existing knowledge associated with the design and placement of prefabricated pastefill barricades through a consideration of asymmetric drive geometry and conditions. The load capacity of prefabricated barricades and their failure modes are considered in relation to abutment geology and barricade geometry that includes curvature and span and drive geometry that includes abutment angles, haunch angles and misalignment. Design charts are provided for typical barricade sizes to provide general guidance for design capacities and optimising location placement based on asymmetric drive geometry. A recent barricade failure is considered in relation to the drive geometry and the potential impact it had on the installed capacity.

Nov 29, 2022

By I D. Gregson, A S. Garcia, K M. MacAndrew

The design work undertaken by Rock Mechanics Technology (now part of Golder Associates (Golder)) has played a major part in successfully establishing mechanised room and pillar working in Indian coalmines, both for the development of new districts and for the re-establishment of old districts prior to pillar extraction on panel retreat.Golder has used appropriate design of pillars, extraction sequences and final snook sizes to minimise ground control risks during pillar extraction. Where the strata will not cave reliably, partial extraction systems leaving either a crush pillar or a substantial yield pillar have been adopted.Remote monitoring of selected pillars during the extraction process using stress cells, extensometry and convergence measurements provides confirmation of pillar behaviour and verification of designs.A new telltale device, giving a visible warning of impending caving, is now installed at all Indian pillar extraction sites and is proving very successful.CITATION:MacAndrew, K M, Garcia, A S and Gregson, I D, 2014. Coalmine pillar design and performance during mechanised pillar extraction in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 347–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M A. Jardine, J A. Miller, M Becker, M Harris

"Although the role of texture has been increasingly recognised as a geometallurgical indicator of ore characteristics and their variability, the ability to appropriately quantify and correlate it with metallurgical performance remains an ongoing challenge. In this study, we propose the 3D characterisation and quantification of ore textures from drill core using X-ray computed tomography (XCT) with an appropriate image analysis methodology (grey level co-occurrence matrices, GLCM). This methodology has been specially customised for application of 3D XCT grey-scale volumes. This approach has potential as an online mine site analysis tool providing detailed 3D information on both quantitative texture and simple mineralogy.The approach is illustrated in this paper using drill core samples that were manually extracted from various rock types and textures representing the Nkomati Main Mineralized Zone (MMZ) sulfide nickel ore deposit. A preliminary classification of the samples was performed based on their particle size distribution after laboratory scale rod milling. Accompanying QEMSCAN analyses were also used to guide the interpretation of the grey-scale mineralogy and texture in the 3D XCT volumes. The resultant GLCM produced from quantitative 3D image analysis of the XCT volumes indicated sensitivity to ore variability and was able to capture a simple mineralogy and grain size distribution. The approach holds many possibilities for geometallurgy, of which the potential for automation is promising.CITATION:Becker, M, Jardine, M A, Miller, J A and Harris, M, 2016. X-ray Computed Tomography – a Geometallurgical Tool for 3D Textural Analysis of Drill Core?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 231–240 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Coal mining legislation makes frequent reference to æSafety Management SystemsÆ but there is a chronic shortage of useful guidance material as to how these might be applied to hazardous exposures. Several studies have indicated that for each death that is reported as a result of an industrial æaccidentÆ, there are five deaths that caused by occupational exposures. Because the deaths from occupational exposures do not occur on site and often well after employment has ceased, they are generally unreported. Improved access to mortality data from coroners, the Australian Institute of Health and Welfare and superannuation service providers (early claims from death and total permanent disability), has given rise to some analysis of death and disability data that provides evidence that there are emerging opportunities to develop and improve safety management systems for hazardous occupational exposures. Issues explored include how safety management systems might be developed in relation to dusts and chemicals and other hazardous exposures to ensure the risk of disorders with long latency periods are reliably assessed and the exposures effectively managed. The current standards and guidelines which refer to safety management systems in general or to management of exposure related hazards are examined. Many standards are based on dose-response studies that provide for an acceptable percentage of workers to suffer adverse health outcomes. An alternative management system might be to apply dose-response relations to health surveillance to identify æat riskÆ individuals and effectively manage health and related safety risk at an early stage.

Jan 1, 2005