Search Documents

In mining industries, materials loading and handling costs represent a significant component of the total (capital and operation) costs. A variety of methods have been applied in surface mine equipment selection in order to select the suitable loading and haulage system with the lowest total cost. The optimal size and number of equipment calculation are very important task for mining engineering because loading and haulage equipment are major proportion of open pit mining cost. Capital and operating cost are considered in objective function with respect to interest rate, insurance and tax in non-linear form. Shovel and truck annual productivity constraint, fleet matching constraint and number of truck per shovel constraint are incorporated in this optimisation problem with continuous variables. This formulation will yield total cost minimisation per hour and good accuracy compared to previous methods.

Dec 6, 2010

By M Wimmer

LKAB operates two underground iron ore mines located in the northern part of Sweden, both using sublevel caving (SLC) as the mining method. Knowledge of the mechanisms of gravity flow is important since it affects both ore recovery and waste dilution. This paper describes results from a large-scale field test carried out at the Kiruna mine with a focus on gravity flow. It is part of Work Package 2 in the I2Mine project financed by the EU. A total of ten rings were blasted. Smart Markers based on radio frequency identification technology were used to monitor the gravity flow. An accurate delineation of the isolated extraction zone requires reliable detection of all recovered Smart Markers and precise knowledge of the 3D position of the markers within the burden. It was therefore necessary to carry out borehole deviation measurements (collar, alignment and trajectory). The blast performance was monitored by high-speed filming, near-field vibration monitoring and velocity of detonation measurements. Three-dimensional stereo images were taken from the drawpoint and the loaded bucket after each mucking cycle. Based upon that, fragmentation was assessed both in 2D and 3D. Furthermore, volumetric differences were determined at the drawpoint, which reflects the mobility of loaded material. For draw control, the Fe content is estimated by measuring weight and assuming a full bucket. The measured volume of rock in each bucket further improves this estimate. Possible flow disturbances occurring at the drawpoint were revealed by video recording. Two-dimensional laser scanning was carried out during mucking to track the position of the bucket and estimate the position and slope of the muck pile.The results from this test clearly show that the gravity flow in the large-scale sublevel cave in Kiruna mine is often of disturbed character. Standard draw occurred only in three rings and shallow draw in the remaining seven rings. In five cases, shallow draw developed towards standard draw, but occurred at rather late stages during extraction (70–125 per cent). The maximum width of the draw varied between 10 m and 13 m except for one ring (6 m). The draw reaches the cave rather early (5–25 per cent extraction) in shallow draw situations and much later (about 50 per cent) during standard draw. Waste originates from above in most cases, while more significant portions often occur at about 20–45 per cent extraction.All the results from this extensive field test are not yet fully analysed, and further field tests are planned. A more detailed insight into gravity flow in large-scale SLC and possible influence by drilling, blasting and the mucking procedure is expected in the future.CITATION:Nordqvist, A and Wimmer, M, 2016. Holistic approach to study gravity flow at the Kiruna sublevel caving mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 401–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By I M. Platten, C J. S Sangster, Y Xie, S C. Dominy

Cononish is a steep, narrow NE-SW trending vein system that was emplaced into late Proterozoic metasediments. It shows brittle style deformation and postdates metamorphism and associated Caledonian foliations. The ore shoots plunge 45¦SW, have a 40 to 80?m intersection with the existing underground development and extend between 40 and 260?m down plunge. Small-scale sulfide-bearing domains within the vein carry the highest gold grades. They collectively define the ore shoots, where one or two and rarely three of the domains are present at an individual site in the vein. Gold occurs as electrum, with minor native gold. Silver occurs additionally as tellurides and native metal. The gold/electrum is fine-grained, generally <100?¦m in size and locally clusters. Visible gold up to 2000?¦m in size is rare. Gold and silver are generally spatially associated with sulfides in quartz. The main sulfide is pyrite, but galena, chalcopyrite and sphalerite occur also. Electrum and gold occur with galena in pyrite-hosted fractures. Gold is also associated with the contacts between galena and pyrite grains. Discontinuity of individual domains, variation in domain thickness and internal heterogeneity results in short scale variation in grade across the structure. Over 16?km of diamond drilling and a 1.2?km exploration adit has provided data to support a Mineral Resource estimate of 169?000?oz Au and 631?000?oz Ag reported in accordance with the 2004 JORC Code.CITATION:Dominy, S C, Platten, I M, Xie, Y and Sangster, C J S, 2013. Gold-silver vein mineralisation at Cononish, Scotland, in Proceedings World Gold 2013 , pp 445-454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By K H. Esbensen, K Engström

The conclusion from the debate over the last decade in the mining sector is that, for grade control, reverse circulation (RC) drill sampling gives more reliable results due to less sampling problems than blasthole samples. However, by conducting the latter with well-controlled procedures there still exist fair possibilities to counteract the major blasthole sampling problems and achieve fit-for-purpose representativeness, especially if based on minimal loss of fines. In the present PhD study, extensive replicate experiments and variographic characterisations are conducted to evaluate the performance of manual blasthole (BH) sampling and sectorial segment sampling. The experiments were performed in Luossavaara-Kiirunavaara AB (LKAB)’s Leveäniemi open pit mine in the north of Sweden. The experimental area is an apatite-magnetite iron ore deposit of the Kiruna type, with the demand to exhibit a maximum of local heterogeneity to allow the experiment the largest possible conclusion powers. Gathering and splitting the complete BH drill cutting cones (fines cone, coarse cone) served as an authoritative reference on which to assess the representativity of the two BH sampling methods.Results show that manual BH drill sampling is able to produce samples with an acceptable accuracy and precision if performed properly and with insight. Based on variographic comparison, segment sampling shows similar precision for chemical grades as the manual sampling, while the particle size distributions were more deviating for segment sampling than for manual sampling at the high and low size ranges. Possible reasons for these partly surprising results are discussed.For further investigation of the performance of BH versus RC drill sampling, a second experiment has been planned on a parallel profile. This will result in an unprecedented opportunity for a full variographic comparison between RC and BH sampling, aimed at designing specific, fit-for-purpose sampling procedures as a function of ore quality, cut-off grades and important contaminant levels.CITATION:Engström, K and Esbensen, K H, 2017. Blasthole sampling (replicate and variographic experiments) in LKAB open pit iron ore mines – fit-for-purpose representativity?, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Z Gao, D Liao, W Sun, S G. Pooley, J Wang, Z Shi, G Jing, S Ren, Q Chen

Yuanjing processing plant is a scheelite and wolframite plant in southern China. Water shortages and recent environmental regulations mean that the plant must reuse the wastewater that comes from the mining operation. This paper describes the efforts to reuse the mining and ore washing wastewater (MOW) in the processing plant. Initial attempts to reuse the MOW in the strong magnetic separation were unsuccessful because the magnetic media pack was seriously fouled by the micro-fine precipitate generated. The focus changed to reuse the MOW in the scheelite flotation circuit, which includes one roughing, one cleaning and three scavenging steps. Laboratory batch tests showed this would likely be successful because using MOW reliably improved the flotation performance in the laboratory tests. Then a 20 day industrial trial was run in the plant. The trial was very successful with the enrichment ratio of WO3 increasing from 17.4 to 23.6, while the recovery remained around 79.2 per cent. The industrial trial was so successful the company immediately adopted the new scheme, which has remained in use ever since. This technical solution not only alleviated serious water shortages, and satisfied environmental regulations but also improved the plant performance.

Aug 24, 2022

By D Craw

Formation of gold-bearing veins in Otago Schist was intimately linked to the structural evolution of the schist belt. The currently-exploited Macraes gold deposit formed in a regional scale shear zone during latemetamorphic uplift of the schist belt. Further exploration for this type of deposit will be facilitated by an increased understanding of the late-metamorphic structural evolution of the schist belt. To this end, a three-dimensional cross section through the Otago Schist has been drawn using structural data gathered at outcrops in a 20 - 40 km wide transect across central Otago. This is the first continuous detailed structural section to be drawn through the belt. The section spans an area from Textural Zone 1 metagreywacke of the Torlesse terrane in the northeast through TZ 4 schist in the central region and across the Caples-Torlesse boundary to Textural Zone 3 schist of the Caples terrane in the southwest. Two different late-metamorphic structural generations are identified in this section: the long-recognised Manorburn Generation, and a new æPoolburn GenerationÆ. The location of the Caples-Torlesse boundary has been refined on this transect by field mapping combined with whole rock geochemistry.

Jan 1, 2001

By G Eastwood, C Joyce, P Ryan, G M. Johnston

Over the years, predictive techniques for Acid Mine Drainage (AMD) and the natural processes affecting acid generation have received considerable attention. Less emphasis has been placed on the sampling strategy and the integration of testwork results with the geological data base. The sampling strategy employed and the development of a geological model to determine the spatial distribution and volume of acid producing material are often crucial for developing cost-effective containment and mitigation measures. The geological model provides a link between the occurrence, timing, destination and placement of mined waste rock. Careful and accurate interrogation of a comprehensive geological database provides this linkage. The AMD testwork program at Cadia in NSW has been designed to identify the temporal selective handling requirements that will be required during operation. Sampling involved collection of representative combinations of all waste rock types identified within an extensive geological database. These samples were subjected to static, kinetic and accelerated weathering predictive tests. Preliminary results have been used to construct a waste block model for the deposit that identifies the quantity and distribution of acid producing material. Integration of the block model with the mine scheduling determines when the material will be mined.

Jan 1, 1996

By L Lorenzen

The selection of samples for metallurgical test work is generally focused on providing geologically representative samples. One of the major problems experienced with metallurgical test work using drill hole data, is the small sample sets selected for metallurgical testing. Major process and financial decisions are being made from results obtained using snapshot samples. Snapshot samples means that samples are basically selected only by grade and spatial location with the assumption that the rest of the orebody or portion of orebody is similar and will respond metallurgically the same way – ie the assumption is that the mineralogy and lithology are basically the same as the test sample. From the test work, algorithms were usually developed and used to describe throughput and recovery using some explanatory variables including grade (mineral chemistry) and ore hardness. These algorithms were then used in the recovery models to determine tonnes produced and plant throughput. However, the metallurgical parameters are a function of many geological factors including grade, lithology, alteration, mineralogy, spatial relationships and SG. In previous years, the limited mineralogical information available was deemed enough for the metallurgist to make decisions as to how many samples are needed to evaluate the metallurgical performance of the ore during processing, and subsequently the basis for the plant design. If the orebody is consistent and not complex or refractory (thus, relative simple lithology), then only spatial and grade samples will be needed to evaluate the throughput and recovery, so limited mineralogical information may be acceptable. There is now, however, an increasing realisation that the mineralogy and geology change, as do the metallurgical characteristics of the orebody, so limited samples may not be sufficient for effective metallurgical test work.It is the purpose of this paper to discuss the effect correct mineralogical information has on the subsequent metallurgical test work program and process selection using a case study. Factors such as type of rock, rainfall and topography are thought to influence the minerals that ultimately form in various orebodies, with the result that different orebodies often react differently during metallurgical test work programs. It is therefore important to obtain accurate mineralogical and elemental deportment data, which will also indicate where the valuable metal containing minerals are located within the orebody. The better you plan and execute your metallurgical test work program during the early phases, the more accurate the decision-making process will be during the selection phase. Improved integration between geology and metallurgy data gathering (geometallurgy) during early phases will result in more accurate predictions with regard to throughput and recovery during modelling and process. Equipment selection will be considerably simpler in later phases with early planning, with improved mine and process scheduling and subsequent net present value (NPV).

Sep 5, 2011

The Central Andes in Peru, Chile, Bolivia, and Argentina , contain two contiguous terranes which were accreted to Gondwanaland between the end of the Devonian and the end of the Triassic. These terranes, Arequipa in the north, and Chilenia in the south, differ from each other in the timing and style of their metallogenic development. However, they contain over 90% of the Central Andean porphyry copper resource. The copper porphyries in the Arequipa terrane are Paleocene to lower Oligocene in age, whereas the Chilenia deposits are mid-upper Cretaceous and mid-upper Miocene. Porphyry copper deposits occur outside these terranes, but are all Miocene in age. Miocene porphyry-style mineralisation also exists in the Arequipa terrane, but is copper-deficient and gold-rich. The accreted terranes may have favoured porphyry and other styles of copper mineralisation because they possessed relatively thin continental crust compared to adjacent parts of the Andes. Crustal thickening which commenced at about 30 Ma in the Arequipa terrane coincided with a major change to polymetallic, precious metal mineralisation which commonly displays high sulfidation characteristics.

Jan 1, 1995

The objective of a mine planning exercise is to plan a safe mine that maximises net present value (NPV) for the project. Two primary elements are key to design of a mine plan optimised to maximise profit: selection of an optimised production rate and selection of an optimised equipment fleet. Both depend upon accurate estimations of capital and operating costs for the equipment and for the life cycle of the mining operation. Once a trial production rate is determined, a primary equipment fleet, ie excavators, haulers, and blasthole drills, can be determined based on material characteristics and haulage distances and gradients. An auxiliary fleet, dozers, road maintainers, service trucks, etc can be determined using less rigid productivity criteria. With an equipment fleet determined, operating and support personnel can be assigned based on shift requirements and equipment operating needs; and material and supply requirements can be estimated. Knowing the areal dimensions of the major equipment items, road widths and repair shop dimensions can be determined. Personnel numbers and supply requirements determine the square metre sizes of offices, change rooms, and storage facilities. Reliable sources of capital and operating unit prices and costs for all these items are referenced in the paper. Once preliminary capital and operating cost estimates are calculated by applying unit costs to equipment, personnel, material and supply needs, potential profit can be tested using DCF techniques. An optimised mine plan can then be determined by testing the potential profitability of multiple mine production rates. Because of the economies of scale, full capital and operating cost estimates must be completed for each production rate in order to produce meaningful comparisons.

Dec 6, 2010

By H He, S Tillotson, S Gibbons, J Shaw

"Water evaluation and management during mining exploration and operational activities is crucial to minimise direct and indirect operational costs and also in delivering mining companies the less tangible, but equally critical æsocial license to operateÆ.Mining is often carried out in remote areas, where the mine will be the most significant and visible user and potential contaminator of water resources. However, wherever it is located, a mineÆs use of water must be managed in the context of two key aspects: the natural parameters of the resource; its abundance, its temporal variability and its chemical and physical qualities other users of the resource; other industry, potable water supplies and ecological requirements of local habitats.It is vital, therefore, that this commodity be assessed to an appropriate degree to help establish the viability and sustainability of the mining project and identify those other stakeholders who may be affected by the mining companyÆs activities.This paper outlines the background to catchment-scale model and presents a cost-effective method for establishing a robust water baseline and creating a water management tool to be used throughout whole mine life cycle. Numerical surface and groundwater modelling has long been established as a tool for reactive management, following collation of yearsÆ worth of data. Now, using freely available remote sensing data and desk study information, analytical modelling techniques can be used cost effectively to provide mining companies with a tool for assessing and managing their water consumption requirements at the outset of a new project venture.The paper includes a selection of case studies to show how the use of analytical modelling can be used as an evaluation and management tool to help not only assess general watershed parameters and water availability but also how it can be used as a tool to provide decision makers with the information to complete æwhat if?Æ scenario assessments. The case studies illustrate how a combined hydrological and hydrogeological model may enable identification of sensitive receptors, water competition issues and contaminant migration pathways to help manage the risks associated with water consumption and its potential contamination from exploration and operational activities.CITATION:Gibbons, S, Shaw, J, Tillotson, S and He, H, 2013. Catchment-scale water modelling and its role in risk management during mining exploration, in Proceedings Water in Mining 2013, pp 175-188 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By P R. L Browne

Study of geothermal systems in the Taupo Volcanic Zone (TVZ) has significantly advanced our understanding of the processes of epithermal mineralisation. The three main lessons learnt are: 1. knowledge of their chemical anatomy; 2. precious metal transport and deposition; and 3. hydrothermal alteration zoning. These are described in the context of ore formation and exploration.

Jan 1, 1997

By G Baiden

The removal of rock blockages in mining operations has long been a risky undertaking, especially in high overhead conditions. Moreover, the assessment of where to put charges and the placement of them has been difficult due to the lack of visibility and safe access to the area. Traditionally, wedging long poles with explosives on them to keep the operator at a relatively safe distance has been the tried and true method of attempting to remove the blockages. Unfortunately, this is not a perfect system as it usually takes several attempts to remove the blockage. Each successive attempt results in even more dangerous conditions for workers and/or damage to the mine due to the successively larger amounts of explosives used until the hang-up finally comes down.Over the years, different ideas have been proposed to improve this process and reduce the inherent safety risks. Some of the technologies that have been trialled include projectiles fired at the hang-up; large, cumbersome arms; and massive amounts of explosives, each of which come with their own inherent safety risks that result in dangerous situations for miners and the mine.After gaining a thorough understanding of the process, Penguin Automated Systems Inc has developed a robotic system that is capable of working in a rock blockage safely. The idea combines the latest in telerobotics technology with 3D scanning and underground geospatial positioning. The hang-up removal is performed by scanning the inside of the hang-up to rapidly develop a geospatially placed 3D model for the operator to use. The 3D model is detailed enough that the operator can attempt to pick the ‘keystone’. A blasting engineer or the operator can then determine the exact position where the explosive charge should be placed in the 3D model and thus at the actual hang-up. The operator, controlling the robotic arm, uses the 3D virtual reality model of the robot system and the actual drawpoint information model to display the location information, the arm can then reach into the hang-up to position the charge using the kinematic model of the robot system. The 3D model is used to provide views inside the hang-up so that the operator can move the arm safely and precisely. This process allows the operator to place the charge (using the 3D representation of the drawpoint) from a long distance away. As the process continues, the end of the arm drills the rock and precisely loads the explosives. The robot then returns the blasting cable to the command station, which is located in a truck at a safe distance from the blockage.This paper will review the development of the system and present the results to date.CITATION:Baiden, G, 2016. Robotic hang-up assessment and removal of rock blockages in mining operations using virtual reality for safety, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 745–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By C Tickell

Achieving occupational health and environmental noise objectives is a major consideration in the planning or operational phase of resource development and industrial projects to meet the needs of the workforce and community and comply with legislative requirements. For material handling systems, ventilation plants, mobile equipment, process plants and fixed infrastructure, noise emissions need to be considered at the design phase. The preferred approach is to provide noise emission technical specifications, but in many cases this is not stipulated. An occupational noise requirement, such as ‘not to exceed 85 dBA at 1 m’, is often provided, but this will not achieve the required occupational or environmental noise objectives and may cause overly stringent requirements when they may not be needed. It should be noted that when developing the technical specification, measuring compliance needs to be taken into account as, in some cases, measuring may be very difficult or even not possible.This paper will discuss the requirements for providing an effective noise specification that ensures the environmental and occupational noise objectives are able to be achieved and that, once installed, compliance can be measured. It discusses planning such as when to set the objective, correlating the appropriate objectives for the environmental and occupational noise requirements, allowing for measurement tolerance, providing a suitable criteria and data format for the suppliers to respond to and methodology to measure compliance. Different phases of a project require different approaches to planning for noise management and these will be discussed in the paper. Examples from 35 years of industry experience will be included.CITATION:Tickell, C, 2016. Preparing effective specifications for occupational health and environmental noise objectives in mining project design and delivery, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 781–788 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Gold mines produce unique water treatment requirements. This paper focuses on case studies of innovative processes used for treatment of water resulting from gold mining and processing. The case studies include treatment of mine dewatering water for beneficial application from an Australian gold mine, Bendigo Mining, as well as treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Gold mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Gold mining and processing often accumulate wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and odorous sulfates. Environmental discharge requirements as well as community needs for water drive mine operators to consider the most appropriate water treatment process. Treatment of gold mine water can require processes including oxidation, pH adjustment, coagulation, flocculation, clarification, further oxidation/adsorption of specific metals such as manganese, filtration, salt reduction utilising reverse osmosis, brine minimisation and other innovative technologies. These processes are discussed through the case studies with examination of the specific treatment process that is required. This paper uses real case studies of gold water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is toward explaining innovative processes where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the local community.

Jan 1, 2007

Base metal sulphide mineralisation on the northern end of Great Barrier Island is spatially associated with hypabyssal intermediate to acidic intrusives, in transgressive structures in indurated, complexly deformed greywackes and argillites. Copper predominates in the mineralisation, with minor accompanying lead and zinc and also some gold and silver. However, in some cases lead or zinc may be the dominant constituent. The mineralisation is generally characterised by only narrow envelopes of weak alteration (propyliticassemblages dominated by chlorite and epidote) and with only minor amounts of quartz accompanying the sulphides, which form a cement in zones of hydraulic fracturing. There are two distinct structural settings to the mineralisation: at MinerÆs Head, in a structurally complex situation in a shell-like zone of crackling in hornfelsed greywacke, in association with both north- and east-striking fractures and rubble breccias associated with the apical part of a large intrusive; and in very narrow, but very strike-persistent, 1inear steeply-dipping fracture zones, exposed on the north coast and inland areas near Tataweka.

Jan 1, 1984

By M McCarthy

Over the last six years Mandalay Resources has increased production rates and improved safety outcomes at its Costerfield mine in Victoria, Australia. This mine is an underground operation utilising narrow mining techniques to extract vertical veins, and produces up to 80 000 equivalent ounces of gold per annum, in both gold and antimony value.The operational challenges of narrow vein mining include controlling overbreak when veins being mined are only 300 mm wide. The mine has developed methods and modified equipment to suit extraction of these veins. Productivity improvements over the period have involved development of a stoping method and equipment to suit 1.8 m wide development drives. Over the last five years and during a skills shortage, recruitment, training and retention of personnel has been key to keeping corporate knowledge and skills to execute a careful efficient mining technique to minimise overbreak.Managing an underground operation close to nearby residents has unique challenges. Historically Victorian residents had family members work as underground miners; however, in the current day with few underground operations in this jurisdiction, community knowledge of mining has decreased. The Costerfield Operations are only 100 m from the nearest residence and the company values community engagement, partnership and investment with local Heathcote organisations.The mine has invested substantially in executive coaching of its leadership team early, which has paid dividends in problem solving potential of that team and ensuring the operation delivers on its promises to all stakeholders. The operation has become safer and employees are now more aware of their individual contribution in producing safe, efficient gold and antimony that benefit the whole operation, community and the region.CITATION:McCarthy, M, 2016. Costerfield – a narrow vein case study, in Proceedings International Mine Management Conference, pp 331-338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

There are circumstances where the ordinary techniques of experimental variography in geostatistics û now in common use despite their recent origin û are not quite successful. This paper describes a new addition to the geostatisticians tool kit developed by one of the renowned leaders in the field to cope specifically with these circumstances. Possible application of this technique will be outlined when it will be seen that there are still problems remaining to be solved in its use for economic evaluation of deposits with irregular mineralisation.

Jan 1, 1984

By M Johnson, M Horrigan

The scope of this report is to examine the aforementioned hypothesis by performing a detailed analytical comparison of a P&H electric rope shovel to an O&K diesel powered hydraulic excavator. In order to complement the integrity of the concluding results, two different size categories will be analysed in order to demonstrate that the findings can be extrapolated and applied to all the machinesÆ size classes. These two size classes are categorised by their bucket sizes and they are in the range of 43 - 58 cubic metres and 23 - 26 cubic metres. It should be noted that electric powered hydraulic excavators will not be considered in this report. In order to compare the electric and hydraulic types, the machine variants that will be analysed are commercial cost-effectiveness and operational flexibility. Although operational flexibility can be an ambiguous characteristic, a clear and thorough definition describing its exact meaning has been included. In order to simplify this study, all the data collected for this comparison have been for overburden removal, eliminating the variation that occurs with the movements of the shovel when selectively mining in the ore deposit. Thus, it ensures that all the data that is compared stems from a common origin for all the shovels. In other words the information will be compared when digging in the same material, loading into the same sized haul trucks, and when possible, with the same operators. Theoretical data received form the respective manufacturers, and actual data obtained from Mount Whaleback, was used for this comparison. This leads to the final comparison, where the operational flexibility and the cost-effectiveness are evaluated, with respect to their individual importance, ultimately influencing the final recommendation.

Jan 1, 2002

By J E. Wheeler, S B. Valine, L G. Albuquerque

It has long been known that closed circuit grinding with a classifier improves grinding efficiency, reduces unit specific power consumption, and reduces over grinding. The classification device removes material from the circuit that has reached the desired size and returns coarse material back to the mill for further grinding. The efficiency of the classifier is an important factor in the overall performance of a grinding circuit. The classifier affects the capacity of the grinding circuit and the metallurgical performance of downstream operations. A review of historical research and modern case studies is used to demonstrate the benefits of high frequency screens for classification in grinding circuits.CITATION:Valine, S B, Wheeler, J E and Albuquerque, L G, 2012. Applications of fine screens in grinding circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 389-394 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012