Search Documents

By Bradley Stoughton

(Cleveland Meeting, October, 1912.) [SECRETARY'S NOTE.-To avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.-J. S.] INTRODUCTION. THIS paper gives the results : first, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows: 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such as, for example, the wear of railroad-rails, of steel and chilled-iron .rolls, car-wheels, etc. 2. These improvements seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example : A series of tests on cast iron

Nov 1, 1912

By William E. Ford, Edward Salisbury Dana

URANINITE. Cleveite. Broggerite. Nivenite. Pitchblende. Isometric. In octahedrons (o), also with dodecahedra1 faces (d) ; less often in cubes with o and d. Crystals rare. Usually massive and botryoidal; also in grains; structure sometimes columnar, or curved lamellar. Fracture conchoidal to uneven. Brittle. H. = 5'5. G. = 9'0 to 9'7 of crystals; of massive altered forms from 6'4 upwards. Luster submetallic, to greasy or pitch-like, and dull. Color grayish, greenish, brownish, velvet- black. Streak brownish black, grayish, olive-green, a little shining. Opaque. Comp. -A uranate of uranyl, lead, usually thorium (or zirconium), often the metals of the lanthanum and yttrium groups; also containing the gases nitrogen, helium and argon, in varying amounts up to 2'6 p. c. Calcium and water (essential?) are present in small quantities; iron also, but only as an impurity. The relation between the bases varies widely and no definite for- mula can be given. Radium was first discovered in this mineral and it has been shown that it and the helium present are products of the breaking down of the uranium.

Jan 1, 1922

By Alfred H. Bell

IN 1945, Illinois produced 75,210,000 bid. of oil, or 4.4 percent of the total for the United States, and ranked sixth in the nation in oil production for the third consecutive year. Production decreased about 3 per cent from that of 1944, when the total Illinois production was 77,413,000 bbl. This is the smallest percentage of decrease in production in the state for any year since a peak was reached in 1940. Daily average production for 1945 was approximately 206,000 bbl. Daily averages by months were as follows:

Jan 1, 1946

Erwin S. SperRy, Bridgeport, Conn.: The analysis of refined copper is a subject of great importance, and has not received the attention it deserves. Copper metallurgists, therefore, will welcome the paper of Mr. Heath with satisfaction. The state of the art of the chemical analysis of copper has been such that consumers, if they could not afford to run any risk, have been obliged to buy copper from the smelter having the best reputation, and a specification for copper to meet certain requirements could not be drawn up by the mere giving of the chemical constituents. Mr. Heath has brought the analysis of the copper to such a state that when a specification calls for copper " equal to Lake copper " one will know immediately what percentage of the pure metal to expect. It seems to be a pretty well established fact that the copper of Lake Superior is practically free from antimony and bitmuth ; and, with the exception of arsenic, the other elements are easily separated from copper by electro-deposition in an acid solution. The authorities differ in regard to the question whether antimony is deposited with the copper in an acid solution. Classen* recommends the employment of a solution containing 10 per cent. of free nitric acid, sp.gr.1.21, and the strength of the current from 0.3 to 0.4 ampere, in order to prevent the other metals from being deposited with the copper; and for this reason, I presume, the method has been generally used. I, myself, have been accustomed to use such a solution for the analysis of copper-alloys, but have found that for such alloys only a small quantity of nitric acid is necessary, if sulphuric acid is present in sufficient amount to give the solution the required conductivity.

Jan 1, 1898

By Gordon E. Frantti

Under the auspices of the Geophysical Committee of Michigan College of Mining and Technology, an investigation was made in Michigan's Upper Peninsula to obtain geophysical data related to the regional subsurface geology in the area covered by Paleozoic sediments. The area surveyed includes that portion of the Upper Peninsula which lies between R18W to R26W and T41N and T49N, covering approximately 1300 square miles. On the index map, Fig. 1, it is represented by the cross-hatched zone west of Munising. Four of the five sites of detailed investigation are indicated by the letters A, B, C, and D. A detailed gravity and magnetic survey had previously been conducted by J. G. Wilson near Perkins, 8 miles north of Rapid River, on a local anomalous area. Results of his work, which showed a large positive magnetic anomaly associated with a gravity anomaly, aroused interest in the possible economic significance of the formations underlying the Paleozoic sediments in this part of the Upper Peninsula.

Jan 1, 1956

By William H. Bassett, C. J. Snyder

Cable sheaths made from common lead have been used to protect underground cables since the beginning of the power-cable industry. Only within the last few years, however, has a systematic study of the production methods and of the causes of failures in cable sheathing been undertaken. Recent increases in the use and demands for service made upon power cables have emphasized the importance of high-quality cable sheaths. It was customary for the users to attribute the cause for their sheath failures to the lack of purity of the lead, but this contention has not been borne out by field and laboratory inspection of the sheaths. During the past two years the writers have had an opportunity to examine various types of sheaths that were removed from power cables after failure. These samples were obtained from various parts of the country and represent, it is supposed, the production of the principal cable manufacturers. Aside from corrosion, the common field difficulties can be classified either as mechanical or structural, as outlined below, and when structural irregularities are found they can all be attributed to manufacturing causes and in no way reflect the purity of the lead. Clasxification of Cable Sheath Failures Other Than Corrosive Mechanical Irregularities A. Splits caused by excessive internal pressure B. Injuries such as nail holes, cuts, tsars, etc. C. Intercrystalline cracks caused by vibration Structural Irregularities A. Splits C. Voids in wall of sheath a. Caused by imperfect welds a. Blisters 13. Holes through sheath b. Laminations a. Caused by yellow oxide inclu- D. Questionable structures sions in sheath wall a. Prominent flow lines b. Blowouts by entrapped gases b. Large areas filled with suboxide during manufacture c. Scattered yellow oxide or dirt C. Caused by inclusions of dirt and

Jan 1, 1933

Jan 1, 1970

By D. J. Mack, R. E. Reiswig

Six examples of the peritectoid transformation were selected from the literature and studied by the method of isothermal transformation. The kinetics and mechanisms of five of the examples are presented as TTT diagrams and photomicrographs. The exist-enc- of a peritectoid in the sixth case is doubtful. ALTHOUGH the peritectoid transformation per se has been known for many years, no precise published data exist concerning the kinetics or mechanisms involved in transformations of this type, except for the brief treatment by Rhines, et al. 1,10 Bearing in mind the fact that investigations of recent years are uncovering more and more peritectoids and suspected peritectoids, a thorough study of the well-established peritectoids appeared to be in order. It was for this reason that a study of the kinetics and morphological mechanisms of six binary peritectoids was undertaken. The six peritectoids selected from the literature for study were those reported at 7.02 wt pct Al-Ag, 26.0 wt pct Sb-Cu, 30.5 wt pct Sb-Cu, 32.3 wt pct Sn-Cu, 8.35 wt pct Si-Cu, and 21.2 wt pct Al-Cu. These selections were based on availability and purity of components, ease of preparation and heat-treatment, and estimated reliability of the available equilibrium diagrams in the regions of interest. EXPERIMENTAL PROCEDURE The alloys used in this investigation were induction melted in electrode-grade graphite and chill-cast in cast-iron split molds. In all cases, the alloys were so brittle that they could easily be broken into samples weighing 1 or 2 g. Chemical analyses showed that the alloys used were close to the respective peritectoid compositions reported in the literature and that the impurity levels were low in all cases. Metallographic examination showed uniform distributions of phases in all samples, indicating uniformity of composition in the samples studied. Isothermal transformation studies were carried out in fused-salt media, using the familiar inter-rupted-quench method. Uniformity of temperature in the salt baths was maintained by continuous stirring with a stainless-steel agitator. On the basis of actual observations of the temperature fluctuations, the estimated temperature control was + 10C for the Ag-Al and Cu-Sb alloys and ±30C for the Cu-Sn, Cu-Si, and Cu-Al alloys. The accuracy of all temperature measurements was estimated to be ±1°C. It was found necessary to mount metallographic specimens of the Ag-Al alloy in cold-curing methyl methacrylate, since the temperatures encountered in mounting in bakelite or lucite caused an appreciable degree of transformation to the ß phase. For the other alloys, wood-flour-filled bakelite mounts were used to avoid extraneous X-ray diffraction lines during the later examination of the metallographic specimens on a Norelco Geiger-counter d if f r ac tomete r. In the X-ray diffraction procedure, agreement between the published diffraction patterns and those obtained in this study was good. This was particularly important for phase identification, since the literature contained little in the way of micrograph description in some cases. Etching of the silver-aluminum alloy for metallographic examination was done by swabbing with either of the following reagents: 1) 10 g CrO3, 1 g (NH4), SO2, 0.5 g NH4NO3, 100 ml H2O, or 2) 10 ml NH4OH, 1 ml 20 pct KOH, 4 ml 3 pct H2O2, 5 ml H2O. The other alloys were etched with the usual bichromate etchant: 2 g K2Cr2O7, 1.5 g NaC1, 8 ml conc. H2SO4, 100 ml H20 (swabbed vigorously). EXPERIMENTAL RESULTS A) The Ag-Al peritectoid at 7.02 wt pct Al— The phase equilibrium involved in this peritectoid is shown in Fig. I.2 The phase boundaries in the vicinity of the peritectoid were most comprehensively established by Hume-Rothery, et al,3 who placed the equilibrium temperature at 448 °C and the equilibrium compositions of the a ß' and y phases at 6.11, 7.02, and 7.24 wt pct Al, respective The alloy used in this study analyzed4 6.95 wt pct A making it slightly hypoperitectoid according to the accepted equilibrium diagram. The rate of the transformation a+ y — ß' varies rapidly with degree of undercooling below the equilibrium temperature, passing through a maximum in the vicinity of 350°C. Thus the TTT dia-

Jan 1, 1960

By CHARLES COURT

I must tell you at the outset that I come to this conference deeply disturbed at the 'role of Government in international dealings in mineral and energy resources'. I am disturbed by- the confusion that now passes for policy. I am disturbed by the short- range view of critical problems taken by a majority of Governments. I am equally disturbed by the even shorter range of view taken by a growing army of industries. Many of them clamour for Governments to solve their problems in a specific way, with little regard for any other sector but their own-and with even less regard for the fact that every time a Government takes over some of their responsibilities they surrender some of their freedom. I would not say that longer range views don't exist. But I would say that they don't prevail at the present time. Instead, we are seeing the constant development of many policies for individual problems which don't tackle the fundamental causes. We must get back to basics without delay.

Jan 1, 1978

Jan 1, 1897

Secretary's Note.—M. Beutter's introductory remarks, being simply a resume of Prof. Hone's paper, with a disclaimer of the intention to criticise it, have been omitted, and the remainder of this contribution lias been somewhat condensed, without omitting any essential statements. M. Beutter, St. Etienne, France* (communication to the Secretary†):—Professor Home observes in $ 47 of his paper that the fluid-compression of steel diminishes piping by forcing the liquid and viscous metal, while the pipe is forming, or after it has formed, into the space so produced, and proceeds to study the different systems of compression, alluding to the four principal ones: Whitworth, Illingmorth, Williams, and Harmet. Having now for many years had in use the last-named process, that of M. Henri Harmet, I shall attempt to explain the difference between it and the three other processes named. The Harmet process does not diminish or close the pipe after it has formed, but prevents it from forming; and I may add that it is the only one of the four which produces this result. It is true that the Whitworth process diminishes the interior hollow by localizing it around the central axis of the ingot, which is afterwards removed by trepanning the hollow forg-ings for which this process has been, I believe, always exclusively used. The Illingworth and Williams processes, which, in my opinion, are applicable only to small ingots, of necessity allow the pipe to form, or (to use the expression of Professor Howe) they allow the surface of the lake of liquid steel to sink into the interior of the ingot, since they involve waiting a certain time before compression, so that (in the case of the Williams process) the ingot-mold can be opened without danger, or (in the case of the Illingworth process) so as to avoid the risk that the steel may enter the grooves produced by the removal of the distance-bars. During the time required for

Jan 1, 1908

Jan 1, 1967

By J. Menashi, D. A. Douglas, A. S. Rappas

Aqueous solutions of Na2Cr04 are reduced with CO to produce hydrous Cr2O3 and NaHCO3/Na2CO3. CH3OH, HCOO- and HCHO in the presence of CO2 also reduce Cr(VI) and yield similar products. It is shown that the rate of Cr(VI) reduction can be represented by the expression -d [Cr(VI) ]/dt = k[Cr(VI)]0.5[R], where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mol (43,000 Btu per lb mol). Rapid reduction rates are attained at temperatures in excess of 220°C (428°F). With these three reductants, a green acid-insoluble readily filterable hydrous Cr203, is formed. With HCHO, significant reduction of Cr(VI) occurs at about 80° to 100° C (176° to 212° F). The product is an acid-soluble violet modification of hydrous Cr203. Solutions of Na2CrO4 contaminated with Mo(VI) and W(VI) can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels.

Jan 1, 1986

By M. W. Bartley, Hugh M. Roberts

Substantial deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper pert of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconform-able, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series, The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement. Introduction Under the waters of Steep Rock Lake, Ontario, situated on the Canadian National Railway, 142 miles west of Port Arthur, the presence of three ore zones containing red and brown Bessemer hematite has been established. These were discovered and have been partly explored by means of diamond and churn drilling, The positions of the ore zones, designated as A, B and C, are shown on the accompanying maps and cross sections. This exploratory work, begun in 1938 by Joseph Errington* and Julian G. Cross, has been carried on by Steep Rock Iron Mines Ltd., and was continued during the winter of 1941-1942. For more than 60 years explorers have known that large quantities of hard hema. tite float of good grade existed along the south shore of Steep Rock Lake, and the presence of ore beneath the lake was inferred by many early geologists and explorers. Despite numerous previous attempts to find ore in place, actual discovery awaited the recent period of intensive exploratory effort in Canada. The results obtained in the drill holes put down since 1938 by steep Rock Iron Mines Ltd. are not only of interest, in themselves, to those concerned with the development of ore deposits, but, taken in connection with the surface exposures of adjoining formations, they form the assemblage of facts from which the geological reasoning in this paper proceeds; accordingly, they are set out here as briefly and exactly as may be.

Jan 1, 1949

By M. W. Bartley, Hugh M. Roberts

Substantial deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper pert of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconform-able, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series, The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement. Introduction Under the waters of Steep Rock Lake, Ontario, situated on the Canadian National Railway, 142 miles west of Port Arthur, the presence of three ore zones containing red and brown Bessemer hematite has been established. These were discovered and have been partly explored by means of diamond and churn drilling, The positions of the ore zones, designated as A, B and C, are shown on the accompanying maps and cross sections. This exploratory work, begun in 1938 by Joseph Errington* and Julian G. Cross, has been carried on by Steep Rock Iron Mines Ltd., and was continued during the winter of 1941-1942. For more than 60 years explorers have known that large quantities of hard hema. tite float of good grade existed along the south shore of Steep Rock Lake, and the presence of ore beneath the lake was inferred by many early geologists and explorers. Despite numerous previous attempts to find ore in place, actual discovery awaited the recent period of intensive exploratory effort in Canada. The results obtained in the drill holes put down since 1938 by steep Rock Iron Mines Ltd. are not only of interest, in themselves, to those concerned with the development of ore deposits, but, taken in connection with the surface exposures of adjoining formations, they form the assemblage of facts from which the geological reasoning in this paper proceeds; accordingly, they are set out here as briefly and exactly as may be.

Jan 1, 1949

By P. H. Metzger, D. W. Fuerstenau

The activation of sphalerite was found to occur at a much lower rate with Pb++ then with Cut++ or Ag+. To prevent activation with Pb++, the ratio [m in solution must approximate 103. An example is given illustrating how this condition is met in practice through the addition of zinc sulfate and soda ash. In selective lead-zinc flotation, the mill operator, especially the one who is concentrating a partially oxidized ore, often must add zinc sulfate and/or soda ash for effective depression of the sphalerite. In the present paper the authors show how this practice prevents the activation of sphalerite in the presence of Pb++. A number of years ago Gaudin (1) postulated that Zn++ might control the activation of sphalerite with Pb++ through competitive adsorption. However, recent experimentation has shown the activation of sphalerite with Ag+ and Cut++ to be a chemical reaction in which silver or copper ions replace zinc in the sphalerite lattice through the formation of a more insoluble sul-fide (2,3,4) Thus, if activation with Pb++ is similar to that with Ag+ or Cu t+, zinc salts should control the activation of sphalerite not through competitive adsorption but because the ratio of [zn++/Pb++] in solution regulates the extent of the chemical exchange between Zn++ and Pb++ in the solid phase. The objective of this investigation has been to study the kinetics and equilibrium conditions for the uptake of Pb++ by sphalerite and to investigate the prevention of lead activation with zinc salts. BASIC PRINCIPLES Sphalerite activation has been shown to be a replacement reaction wherein a less soluble compound is formed at the expense of the more soluble zinc sul-fide (2,3,4) For example, if sphalerite is placed in an aqueous silver nitrate solution, ZnS gives to the solution more S= than can exist together with Ag+, and hence the following reaction takes place: ZnS + 2 Ag+? Ag2 S + Zn ++; k = [zn ++]/[Ag ++]2 = 10 26 (1) Therefore, ZnS will dissolve in the presence of Ag+ and activation of sphalerite with Ag+ will proceed after monolayer coverage by solid state diffusion until equilibrium conditions are reached in the system (2, 4) Because of the large difference in the solubility of ZnS and Ag2S, zinc salts cannot affect the reaction unless a complexing agent, such as cyanide ions, is present to complex Ag+ more tightly than Zn++ . By complexing Ag+ and Zn++ in solution, the uptake of Ag+ by sphalerite can be regulated by controlling the ratio m. . Experimentally (2) it was found that the activation of sphalerite by Ag+ could be prevented through the addition of NaCN if this ratio reached a value of approximately 10 26. The mechanism of sphalerite activation with copper salts is given by the following reactions: ZnS + Cu ++ ? CuS + Zn + + ; (2) k = [Zn++]/[Cu++] = 10 11 ZnS + Cu + ? Cu2S+ Zn++; (3) Experimentally Mao (3) found that the activation of sphalerite with Cu++ or Cu + was prevented if the ratios expressed in Equations 2 and 3 were approximately l09 and l022, respectively, with cyanide ions as the deactivator. Although zinc salts do not affect the activation of sphalerite with silver or copper ions in the absence of a complexing agent, activation with lead ions theoretically can be controlled by the addition of zinc salts because of the relatively small differences between the solubility of ZnS and PbS (5). Equilibrium

Jan 1, 1961

By H. M. Chance

Jan 1, 1887

SAN FRANCISCO SECTION Roy H. ELLIOTT, Chairman - T. A. RICKARD, Vice-chairman W. H. SHOCKLEY, Secretary-Treasurer, 959 Waverley St., Palo Alto, Cal. D. A4. RIORDAN C. F. TOLMAN, JR. A joint meeting of the local sections of the several national engineering societies represented in San Francisco was held at the Engineers'. Club on Thursday evening, Sept. 26, 1918. The subject for the evening, "Fuel Conservation," was ably discussed by a-number of representatives of the Federal Administration and by engineers interested in the generation and utilization of all kinds of power on the Pacific Coast. The following extracts from papers presented at this meeting have been selected as being of the greatest interest and value to members of this Institute. Problems of the Fuel Administration ALBERT E. SCHWABACHER.-America's war needs call for 100,000,000 more tons of coal this year than in 1917, and 200,000,000 tons more than in 1914, when the war started, and this increase must come from a weaker man-power than that of 1917. It must be transported by a railroad system that has not been improved since the war started, and has been burdened with inconceivably greater demands than were made upon it before the war. This tremendous increased demand must be met by most intensive work in three directions; increased production, efficient conservation, and a distribution system which will insure against lost motion. While every European country has decreased its coal production since the war began, the United States has mined 50,000,000 tons more coal, during the first year of the war, and will increase this by another 50,000,000 the present year. Every 8 days there are being mined and transported as great a weight of coal as of the entire wheat crop of the United States. Of the 735,000,000 tons of coal which must be made available for consumption by our railroads, ships, war industries and people, 100,000,000 tons will come from the anthracite fields, the remainder from the bituminous fields. In 1917 there were produced about 330,000,000 bbl. of oil, and this year an additional amount over last year's production, of approximately 23,000,000 bbl. will be required. Water power developed 5,000,000 hp., the demand greatly exceeding the available supply.

Jan 12, 1918

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast' and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By R. W. Vieth, S. A. Bradford

THE orientations of tetragonal tin crystals are commonly examined by either the transmission Laue method or the back-reflection Laue method. The predominant planes and zone axes of the pattern are plotted on a Wulff net and indexed by measuring the angles between planes and directions. The problem of identifying the Laue spots has been approached in several different ways. Nicholas 1 tabulated interplanar angles for ten planes but did not relate the angles to permutation of indices or sign. A table of angles between adjacent planes and of angles between adjacent zones was published by Chandrasekhar and veal.' These tables are very helpful, provided the film shows all the low-order zones that occur within about 20 deg of each other. Frounfelker and Hirthe's compilation3 of angles between the (001) plane and twenty-nine other planes is useful for the indexing, only if the (001) spot can be found on the film. For all but the simplest orientations, however, more information is needed to index the diffraction spots. Standard stereographic projections, such as those published by Bicelli, 4 provide part of the information required. By their nature, these projections show the positions of only a few zone axes. In the tetragonal system many low-order zone axes are not normal to the planes having the same indices. Consequently, planes and directions can have entirely different positions on a stereographic projection. For example, the [011] zone axis is 33 deg from the normal to the (011) plane. The crystallographic orientation usually has to be deduced from a combination of the predominant zone axes and a few low-order planes that appear on the film. In addition to a standard stereographic projection of the planes, a stereographic projection of the directions is needed. Such a projection can be constructed from the angles given in Table I. To provide more information about angles between planes and directions, we have calculated interplanar angles up to (332) and angles between planes and directions up to [332] on an IBM 1620 computer. The angles are differentiated according to permutations of sign and indices. Those doing research on tin single crystals are welcome to request a copy of these tables from the authors.

Jan 1, 1967