Search Documents

By Richard L. Ashbrook, John F. Wallace

Several high-temperature eutectics of cobalt and nickel alloys were modified by small additions of selected elements. Thes-e alloys were compared to unmodified melts for microstructural variations. A few modified compositions were selected on the basis of structure and their tensile and stress-rupture behavior determined. The results of stress-rupture tests in air at 1800 F and room-temperature tensile tests of four high-temperature eutectics showed modification capable of producing substantial improvements in properties. The microstructures were altered and mechanical properties improved by: a.) dispersing a subordinate phase more uniformly throughout the matrix; b) replacing large continuous -network or platelike constituents with small equiaxed discontinuous phases; and c) by forming new, finely divided phases. tHE term "modification" is most commonly used to describe the refinement in microstructure of the Al-Si eutectic that occurs as a result of rapid cooling from the melt or on slow cooling after treatment with small amounts of sodium.1 "Modification" has also been used to describe the change from flake to spheroidal graphite in the austenite-graphite eutectic of cast iron.2 This change of graphite shape is accomplished by small additions of cerium or magnesium.3 Other systems have also been shown to be capable of modification, for example: Pb-Sn by copper;4 Al-Cu by sodium;5 Al-Mn by sodium;5 and Pb-Sb by aluminum.5 Although modification of Al-Si alloys and cast irons is usually accompanied by improved mechanical properties, a general definition of modification has been suggested to include the effect of small quantities of impurity elements on the microstructures of all eutectic alloys, regardless of the effect on the mechanical properties.6 In this paper, the term "modification" is employed in a broad sense to include the formation of third phases or even the supplanting of one of the binary eutectic phases by a third phase. The mechanism of modification, as for any solidification phenomenon, must be considered primarily in terms of nucleation and growth. Although both nuclea-tion and growth mechanisms are required to explain all the phenomena observed in connection with the solidification of modified eutectics, various investigators have usually favored one or the other.7"16 It has been shown that modification of a binary eutectic can be effected by addition of a solute element that has greatly different distribution coefficients or k values in the two phases of the eutectic. Under these conditions, differences in the temperatures at the solid-liquid interfaces of the two phases retard the growth of one phase with respect to the other.4 It has also been shown that increased undercooling favors a transition from a rodlike eutectic to a globular eutectic.17 A mechanism proposed for the transition from lamellar to rodlike eutectics depends on the concept of constitutional super cooling.18 The modification of eutectic alloys may be of interest for high-temperature service as well as at room temperature. Although "high-temperature eutectic alloys" may appear to be a contradiction in terms, many eutectic systems, including those studied in this work, have melting points in excess of 2400°F. One of the mechanisms by which high-temperature alloys are strengthened is dispersion of a relatively brittle phase such as an oxide, carbide, or an inter-metallic compound throughout a ductile matrix. For a given volume fraction of dispersed phase, strength is increased by decreasing the size and spacing of the dispersed particles.19'20 Furthermore, room-temperature ductility may also be increased by changing the shape of a brittle dispersed phase from platelike to equiaxed or spheroidal.8 Overaging and redissolving of the secondary phase limit the maximum temperature to which precipitation-hardened alloys can be used. However, in a binary eutectic system, both phases coexist up to the melting point. Although all eutectic structures are not completely stable,21 a dispersion-hardened cast high-temperature alloy might result if a fine distribution of one of the eutectic phases could be obtained during solidification. An additional reason for interest in eutectic alloys is their excellent castability.22 Since eutectic alloys, like pure metals, freeze at a single temperature rather than over a range of temperatures, their castability is superior to solid-solution alloys with long liquidus to solidus ranges. The purpose of this research was to study the effects of small solute additions on the microstructure and mechanical properties of a number of high-melting-point eutectic compositions.

Jan 1, 1967

By AIME AIME

THE Engineering Education Committee of the Institute convened at the Engineering Societies Building on Feb. 18, .1929, with. E. A. Holbrook, dean of the Schools of Mines and Engineering, University of Pittsburgh, in the chair. STATISTICAL' STUDY OF STUDENTS IN MINING The first paper, a statistical study of the students enrolled in courses leading to a mining degree in 40 institutions, was presented by H. D. Keiser,, assistant editor of the Engineering and Mining Journal; who gave a brief outline of an article he was about to publish in ?that journal?. The complete article appears in the issue for March 30; 1929: To avoid repetition the results are summarized as follows: A request was sent to 42 institutions which give courses in mining' for the number of students enrolled as freshmen; sophomores; juniors, seniors and special students in mining for the years 1925-26, 1926-27, 1927-28, 1928-29. Two of these colleges replied that there were no students in mining. Students' enrolled in courses in metallurgy, geology and engineering, other than mining, were excluded from the statistics:. The statistics received were arranged in, four groups, according to the completeness of the information. One complete group of 25 institutions 'shows as follows:

Jan 1, 1929

By Frederick G. Clapp

SINCE oil journals commenced to feature the progress of Iraq pipe-line developments and since newspapers undertook to follow the discussions between a certain large oil company and an Asiatic nation, I have repeatedly been asked questions that are only answerable by setting forth the essential geographic and historical facts of concessions in that part of the world. In so doing effort will be made to correct erroneous statements made in various quarters: and mistakes herein are being kept as low in number as possible. Perhaps the best-known concession in the Middle East is the one of the Iraq Petroleum Co., covering the greater part of the portion of the kingdom of that name- lying east of the Tigris River. West of the stream is the concession of the British Oil Development Co., which takes in all presumed petroliferous areas in western Iraq. No other important oil concessions exist in that country, except for the lands of the Khanikin Oil Co., which operates in "Transferred Territories" on the border of Persia. East of and continuous with the Iraq fields are those of Persia where the Anglo-Persian Oil Co. holds the well-known D'Arcy concession comprising three-quarters of the country, omitting the five northern provinces. This is the only valid existing concession in Persia, so far as known, except certain old firmans that permit development at Semnan in central Persia and possibly also certain regional grants to a French banking syndicate in eastern Mazanderan Province.

Jan 1, 1933

By MARSHALL D. DRAPER

THERE are said to be about 150 operating companies in Kotchiu, most of these being small, corresponding in degree to lessees in western mines in the United States. Of the total number there are probably forty large companies having their own smelting plants equipped with one or two furnaces, slag crushing plant and other accessory equipment. A few plants, not more than ten, do custom smelting. There are in all about fifty smelting plants in Kotchiu. With little variation, the equipment and methods are the same. The plant usually consists of two furnaces, one being in operation while the other is being relined 01- re- paired. An adjoining house contains one or more of the large buffalo-drawn Chilean mills for crushing slag. A few houses for the working coolies, with more pretentious ones for the owners, complete the establishment, the whole being surrounded by a compound wall 8 ft. high.

Jan 1, 1931

Jan 1, 1923

Jan 1, 1923

Jan 1, 1967

By Owen Thornton

Recently equations have been presented by Rose and Bruce' and by Rose², showing how the relative permeability of a reservoir rock may be determined from the capillary character of the rock. In particular, equations were developed to show the relationship between capillary pressure and the effective permeability to the wetting phase in a poly-phase flow system. The equations are as follows (nomenclature the same as in the Rose and Bruce paper) Rose and Bruce assume that the average length of path (L,), which the wetting fluid follows in flowing through a porous media is independent of the saturation to the wetting phase, so that 1 is a constant dependent only on the k rock, and the permeability to the wetting phase is a function of the saturation and of the capillnry pressure: In measuring the flow of ekctric current through partially saturated core samples, it has been observed that the electrical resistance usually is not a simple linear function of saturation. This fact indicates that the average length of path in the flow of electric current is not independent of saturation, but rather that the tortuosity of the path depends upon the average saturation to the conducting fluid as well as upon the characteristics of the rock. itself. Inasmuch as the flow of fluid and the flow of electric current in many respects are analogous, it may be indicated further that the length of path for fluid also may not be independent of saturation. The following relationship can be derived to express the resistance to flow of electric current through a core sample partially saturated with conductive wetting phase, the non-wetting phase being non-conductive: where L is the average length of path followed by the current in flowing through a length L of partially saturated core, where L is the length of current path when the core is fully saturated, and where Rs and R, are the specific resistivities of the partially saturated and saturated core sample, respectively. It will be noted that R., the specific resistivity of the core sample when S, = 1.0, is equal to the "formation resistivity factor"' multiplied by the specific resistivity of the saturating fluid. If it be assumed that the average lengths of path for fluid flow and for the flow of electric current are the same, then equation (5) may be combined with equations (l), (2) and (3) to give the following relationship: The above equation suggests including a correction for tortuosity when calculating the relative permeability of a reservoir rock to a wetting phase. The correction factor may be obtained from the resistivity-saturation relationship. For instance, the following calcu- lations are obtained for the unconsoli-dated sands described by Leverett Kw Kw Sw R°/Rs Pt/Pc¹ (Calc.) (Obs.) 0.30 0.08 0.88 0.02 0.0 0.40 0.16 0.94 0.06 0.04 0.50 0.27 0.97 0.14 0.11 0.60 0.40 0.98 0.26 0.21 0.70 0.53 0.98 0.39 0.35 0.80 0.68 0.99 0.57 0.54 0.90 0.84 0.99 0.77 0.76 1.00 1.00 1.00 1.00 1.00 It will be noted that the agreement between the calculated points and the observed data is rather good. Further investigation of the above method for obtaining relative permeabilities may be merited. For many sands within specified ranges of saturations the following relationship has been found to hold approximately': — =SW"......(7) Rs The exponent n in the above equation has been found to equal two for many sands so that equation (6) reduces to the following: The writer acknowledges the permission of The Texas Co. to submit this note for publication. 1. Walter Rose and W. A. Bruce—Jnl. of Pet. Tech., Vol. 1, No. 5, p. 127 (1949). 2. Walter Rose—Jnl. of Petr. Tech., Vol. 1, No. 5, p. 111 (1949). 3. G. E. Archie— -Trans. AIME, 146, 54 (1942). 4. M. C. Leverett— Trans. AIME, 142, 152 (1941). 5. M. C. Leverett—Trans. AIME, 132, 149 (1939).

Jan 1, 1949

By Owen Thornton

Recently equations have been presented by Rose and Bruce' and by Rose², showing how the relative permeability of a reservoir rock may be determined from the capillary character of the rock. In particular, equations were developed to show the relationship between capillary pressure and the effective permeability to the wetting phase in a poly-phase flow system. The equations are as follows (nomenclature the same as in the Rose and Bruce paper) Rose and Bruce assume that the average length of path (L,), which the wetting fluid follows in flowing through a porous media is independent of the saturation to the wetting phase, so that 1 is a constant dependent only on the k rock, and the permeability to the wetting phase is a function of the saturation and of the capillnry pressure: In measuring the flow of ekctric current through partially saturated core samples, it has been observed that the electrical resistance usually is not a simple linear function of saturation. This fact indicates that the average length of path in the flow of electric current is not independent of saturation, but rather that the tortuosity of the path depends upon the average saturation to the conducting fluid as well as upon the characteristics of the rock. itself. Inasmuch as the flow of fluid and the flow of electric current in many respects are analogous, it may be indicated further that the length of path for fluid also may not be independent of saturation. The following relationship can be derived to express the resistance to flow of electric current through a core sample partially saturated with conductive wetting phase, the non-wetting phase being non-conductive: where L is the average length of path followed by the current in flowing through a length L of partially saturated core, where L is the length of current path when the core is fully saturated, and where Rs and R, are the specific resistivities of the partially saturated and saturated core sample, respectively. It will be noted that R., the specific resistivity of the core sample when S, = 1.0, is equal to the "formation resistivity factor"' multiplied by the specific resistivity of the saturating fluid. If it be assumed that the average lengths of path for fluid flow and for the flow of electric current are the same, then equation (5) may be combined with equations (l), (2) and (3) to give the following relationship: The above equation suggests including a correction for tortuosity when calculating the relative permeability of a reservoir rock to a wetting phase. The correction factor may be obtained from the resistivity-saturation relationship. For instance, the following calcu- lations are obtained for the unconsoli-dated sands described by Leverett Kw Kw Sw R°/Rs Pt/Pc¹ (Calc.) (Obs.) 0.30 0.08 0.88 0.02 0.0 0.40 0.16 0.94 0.06 0.04 0.50 0.27 0.97 0.14 0.11 0.60 0.40 0.98 0.26 0.21 0.70 0.53 0.98 0.39 0.35 0.80 0.68 0.99 0.57 0.54 0.90 0.84 0.99 0.77 0.76 1.00 1.00 1.00 1.00 1.00 It will be noted that the agreement between the calculated points and the observed data is rather good. Further investigation of the above method for obtaining relative permeabilities may be merited. For many sands within specified ranges of saturations the following relationship has been found to hold approximately': — =SW"......(7) Rs The exponent n in the above equation has been found to equal two for many sands so that equation (6) reduces to the following: The writer acknowledges the permission of The Texas Co. to submit this note for publication. 1. Walter Rose and W. A. Bruce—Jnl. of Pet. Tech., Vol. 1, No. 5, p. 127 (1949). 2. Walter Rose—Jnl. of Petr. Tech., Vol. 1, No. 5, p. 111 (1949). 3. G. E. Archie— -Trans. AIME, 146, 54 (1942). 4. M. C. Leverett— Trans. AIME, 142, 152 (1941). 5. M. C. Leverett—Trans. AIME, 132, 149 (1939).

Jan 1, 1949

By Robert T. MacMillan

Of all the mineral substances utilized by man, salt or sodium chloride has one of the longest and most varied histories. Because all animal life is descended from marine organisms, sodium and chlorine became necessary to life, and as sodium chloride meets requirements most readily, common salt has been essential to human and animal diets from earliest times. As civilization progressed, man learned to evaporate sea water and brines of saline lakes and springs to obtain salt, and gradually ceased to depend on the flesh of animals and the occasional salt outcrops or "salt licks" they frequented. He also learned that salt had a multitude of uses, particularly as a preservative of meat and other foods. The importance of salt in the minds of early men may be readily seen from many allusions in the Bible and other ancient writings. Expressions such as "not worth his salt," and "the salt of the earth" are deeply embedded in the English language. Salt has symbolized friendship, fidelity, purity, and hospitality. It has been used as currency; had religious significance; caused wars; and has been a favorite commodity for taxation. The English word "salary" stems from the Latin word for salt, in which Roman soldiers received part of their pay. Although salt today retains its dietary importance, it has thousands of other uses. Of each 100 pounds produced in the United States less than three pounds is for table use. The other 97 pounds goes for agricultural, industrial, and chemical uses. Fortunately, reserves of salt are enormous and reasonably well distributed on the face of the earth. The sea is an inexhaustible source of salt which may be had at prices which vary with climate and other factors. In addition, large underground salt deposits and many salt lakes, springs and playas are scattered throughout the world. Most countries have access to a salt supply, although some are more favored than others. Properties Crystallized sodium chloride or common salt is known as halite. Its molecular weight is 58.454 and it contains, by weight, 39.34 pct sodium and 60.66 pct chlorine. Alternate positions in the cubic lattice are occupied, respectively, by negative chloride and positive sodium ions; the crystal form is isometric. Crystallization from water produces concentric shells, and when broken, a crystal shows conchoidal fracture. Salt has a hardness of 2.5; its specific gravity ranges from 2.1 to 2.6 for rock salt and is 2.165 for the pure crystal. The refractive index is 1.554; it melts at 800.8 ± 0.5°C and boils at 1413°C. Its heat of fusion is 123.59 cal/ gram. Salt is transparent or translucent and highly diathermous. It is colorless when pure and has a vitreous luster. Salt containing traces of iron oxides has varying shades of yellow, orange, brown, pink, or red. The peculiar shade of red sometimes found in that produced by solar evaporation of sea water has been attributed to tiny organisms. Blue mottlings sometimes seen in halite crystals have been attributed to colloidal sodium. Salt is soluble in water to the extent of 35.7 parts per 100 parts of water at 0°C and 39.8 parts per 100 of water at 100°C. The small difference in solubility with increasing temperature is important in the economics of producing salt by evaporating brine. Salt has a negative heat of solution which is 1.281 kg-cal/ mole at 18°C in 200 moles of water.

Jan 1, 1960

By G. A. Beske, P. Hilsch, J. Wulff

The effects of the growth precipitates on the su-perconduching properties of an Al- 15 al. pel Zu alloy have been studied using magneization, transition lem-perature, and residual resistivity measurements. Aging at 230C for 1/2 to 11 he produces an increase in Hfp, Ike field of first penetration, and tut increase in trapped flux. The upper critical field, Hc2 remains constant for such aging tunes. Aging at 200°C produces a decrease in Hfp and an increase in trapped flux. The transition temperature remains constant at Tc - 1.227° ± 0.02°K for aging at 220°C for tims of from 1/2 to 10 hr, and for aging at 200°C it remains constant at Tc. = 1.18° i 0.02°K for times from 1/2 hv to 26 hr. The observed behavior indicates that the superconducting matrix when aged at 220°C behaves tike a type U su-perconducior, but when aged at 200°C behares like a type I superconductor. The magnetization changes after aging can be attributed to the growth and clutnge in distribution of the precipitate in a matrix of fixed composition. IT has been realized for some time that the superconducting properties of alloys are highly structure-sensitive. This is evident in the work of Mould and Mapother1 who examined the properties of an aluminum alloy. Precipitation effects have also been briefly mentioned in other studies.2-4 Bonnin and coworkers5 have observed a sharp inc rease in trapped flux in an A1-Mg alloy when the residual resistivity reaches a value that indicates it is a type II superconductor. Recently Blanc, Goodman, and Nemoz5p have reported on precipitation effects in A1-Ag alloys. Detailed studies of precipitation in Pb-Sn and Pb-Cd alloys made by Livingston6 serve to show that the upper critical fields are enhanced by quenched-in solute. Furthermore. at various stages in the precipitation process? the upper critical field is determined largely by the remanent solute. The observed magnetic hysteresis and trapped flux in such alloys result from the interaction between precipitate and the flux filaments in the mixed state. The flux trapping appears to depend largely on the precipitate distribution and is greater if the superconductor is type II than if it is type I. To examine the effect of precipitation in another alloy system, particularly one in which the composition of the superconducting phase does not change significantly during the course of precipitation, the Al-Zn system seems interesting, especially in view of the transition temperature and resistivity studies of Chiou and seraphim.' Furthermore, the recent detailed electron-microscope studies of an Al-Zn alloy by Richards and Garwood8 provide a guide for relating superconducting properties to changes in structure. For these reasons, magnetization, transition temperature, and residual resistivity measurements for varying times of heat treatment at two temperatures were made with a -15 at. pct Al-Zn alloy. The results are reported in this paper. I) EXPERIMENTAL The alloy used was prepared by Cominco Products Inc. from 99.9999 A1 and 99.999 Zn. It was chill-cast, swaged, and drawn to 0.125-in.-diam rod. The analyzed composition was 15.6 at. pct Zn (31.1 wt pct). A jeweler's saw was used to cut the 0.125-in.-diam rod into the 0.875-in. lengths needed for magnetization measurements. The ends of the cylinders were slightly beveled to remove the sharp edges. A portion of the original 0.125-in.-diam rod was drawn into 0.010-in.-diam wire and used for transition temperature measurements. Specimens were suspended from wires within a vertical furnace during heat treatment. All were homogenized at 500°C for a minimum of 3 days and subsequently solutionized for times in excess of 6 hr. The solutionizing temperature was held constant to +3°C. Individual specimens were homogenized, quenched, and aged several times and no effects indicating loss of zinc were noted. The suspended specimens were quenched by cutting the wires and allowing the specimens to fall into a silicone oil bath held at the aging temperature. They were then isothermally transforked by aging in the same bath used for quenching. After aging for the required time (approximately 10 min aging was necessary before the upper critical field reached a fixed value), they were briefly (1 to 2 sec) dipped into an acetone bath at room temperature to remove adherent oil and then immediately transferred to liquid nitrogen where they remained until inserted into the helium bath (usually within an hour). The temperature of the aging bath was held constant to +3°C for longer aging times. The cryostat used for the measurement of superconducting properties consisted of outer and inner dewars for liquid nitrogen and liquid helium, Stokes 6-in. booster diffusion pump and Stokes Model 212 mechanical pump, temperature controller to measure and control the temperature of the helium bath, and a superconducting solenoid with inserted search coils to provide the magnetic field and measure the magnetic moment of the specimens. A schematic diagram of the cryostat is shown in Fig. 1. An ultimate temperature of 0.85°K was reached with this apparatus. The temperature controller used is similar to the one described by Blake and chase.' A 0.5 pct Allen-Bradley carbon resistor and a nichronle heater (200

Jan 1, 1968

By S. Warren Hobbs

The section of the Northwestern United States that includes the northern Rocky Mountains and adjacent areas to the west and east is one of large mineral production and important mineral potential. The metallic ore deposits vary widely in age and type and their geologic settings are similarly diverse. A brief resume of the region's physiographic characteristics and geology sets the framework for the selected ore districts that are described in following papers and makes it possible to place these ore deposits in their proper reference to space and time.

Jan 1, 1968

By M. Prats

This paper presents a method for obtaining the correct values of the breakthrough sweep efficiency of the staggered line drive, taking into account the proper shape of the breakthrough streamline. Results obtained were different from those previously published, which were obtained by using an inexact shape of the breakrhrough streamline. INTRODUCTION In Section 9.31 of Muskat's' The Flow of Hotnogeticous Fluids Through Porous Media, it is stated that in a staggered line drive flood "the streamline of highest average velocity [is] the line of centers between input and output wells" (see Fig. I). Muskat used this concept to determine the relationship between the breakthrough sweep efficiency and the geometry of the staggered line drive pattern. Although it is clear from symmetry considerations that the breakthrough streamline passes through the midpoint between input and output wells, it is equally clear, as shown in Fig. 239 of Ref. 1, that the breakthrough streamline is not represented very well by the straight line joining the input and output wells. Therefore, it is desirable to determine the proper relationship between the breakthrough sweep efficiency and the pattern geometry by using the proper shape of the breakthrough streamline. METHOD OF SOLUTION It was found that the effect of the geometry of the staggered line drive on the breakthrough sweep efficiency can be investigated easily by making use of the method developed in Ref. 2. With this method, it can be shown that the general complex potential for the staggered line drive, which can be considered as a rectangular five-spot, is given in the coordinate system of Fig. 1, by O(z) = In cn(z\m) = +(x,y) + i $(x, y) . (1) where z = x + iy, +(x, y) is the potential distribution and $(x, y) is the stream function. The function cn (zm) is a Jacobian elliptic function of parameter m and has simple zeros at z,. = (2n + 1) K + 21iK and simple poles at z, = 2nK + (21 + 1)iK. Thus, the complex potential behaves like a(z) = ln(z - zr.) in the neighborhood of the production wells and behaves like a(z) = - ln(z - Z,) in the neighborhood of the injection wells. Since (z - z1.v) = rll.ei, we note that the potential + has the proper logarithmic behavior near the two wells, while the stream function $ varies with the angle, decreasing clockwise around the production well and increasing clockwise around the injection well. The functions K(m) and K'(tn), related by K(m) = K'(m,), where m + m, = 1, are known as the complete elliptic integrals of the first kind. By use of other properties of the Jacobian elliptic functions, the general stream function distribution for the staggered line drive can be obtained from Eq. 1: From the Jacobian elliptic function values, sn(0lm) = 0 dn(O(m) = cn(0jm) = 1, and f[K'(m)Iml = 03, it follows that the stream function given by Eq. 2 satisfies the proper symmetry conditions near a production well P located at [K(m), 01 and an injection well I located at [0, K' (m)]. That is, the line IOP in Fig. 1 is a streamline with value G (0. 0) = -0. and the straight lines connecting I and P to the point [K(m), K' (m)] is a streamline of value $[K(m), K' (m)] = -7/2. Similar symmetry conditions are obtained near other wells. It should be nuled that for m = m1, = 0.5, Eq. 2 reduces to the stream function distribution of the regular five-spot given in Ref. 7. SHAPE OF THE BREAKTHROUGH STREAMLINE It is apparent, from symmetry considerations, that the breakthrough streamline ($,) passes through the point [K(m)/2, K' (m)/2]. Its value there is so that the shape of the breakthrough streamline $,, is given by

Jan 1, 1957

By A. W. Gauger

WITHOUT QUESTION the Commonwealth of Pennsylvania contains the most remarkable coal deposits of the whole world. Within its borders ,are to be found excellent coals ranging in rank from the high volatile bituminous of the western part of 'the state through the low volatile or semi-bituminous of central Pennsylvania to that aristocrat of solid fuels, anthracite, found in the East. . . . But while other states and even the Federa1 Government have recognized the needs of the coal industry, Pennsylvania has not. Though bituminous coal represents one of the most important industries in the state, far more important in annual productive wealth than agriculture, for example, hundreds, of thousands of dollars have been spent on agricultural research whereas little or nothing has been spent on coal investigation.

Jan 1, 1932

By K. A. Grange, W. S. Holt, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By W. S. Holt, K. A. Grange, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By W. S. Holt, E. T. Tkac, R. A. Grange

QUANTITATIVE knowledge of the time element involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 135-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Ae3 and Ae1), the temperature range of martensite formation, and the end-quench hardenability. These data are directly applicable to the heat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. MATERIAL All specimens were prepared from a 13-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: Mn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, i.57: MO, 0.36: Al, 1.26. The forged bar was normalized from 1750°F (955°C) and then tempered for one hour at 1200°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. EQUILIBRIUM TRANSFORMATION TEMPERATURES In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Ae3, and the maximum temperature at which austenite is completely unstable, Ae1, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1946

By John A. Gann

WITHIN a very few years magnesium has sprung from oblivion, from classification as a technically unknown, little appreciated, and expensive material to front-page importance in many fields of engineering. Bunsen may be considered the real founder of our present magnesium industry. In 1852; he prepared this metal by the electrolysis of fused magnesium chloride in a porcelain crucible. In the following years the electro¬lytic process became recognized as superior to chemical reduction methods and Germany became the world's chief producer, installing the first electrolytic magnesium plant in 1886. ' Thirty years later, national defense requirements, occasioned by the outbreak of the World War and the cutting off of imports, caused France, England, and the United States to begin production. Most of this magnesium was used for military purposes so the close of the war resulted in a large curtailment in production. A few companies, however, encouraged by the early success of the Germans and by the rapid developments taking place in aeronautics, and confident in the certain future and ultimate value of this metal, undertook extensive re¬searches in its production and utilization. A variety of production methods, both chemical and electrochemical, were investigated and some of them operated on a commercial scale. Reduction of the oxide with carbon at high temperatures and the electrolysis of the oxide in a fluoride

Jan 1, 1932

By W. P. Haynes

ESTIMATED United States crude-oil production during 1943 established a new annual peak of 1,500,000,000 barrels, a daily average of 4,118,000 barrels. This would be an increase of 315,000 barrels per day, or 8 per cent over 1942 and 7 per cent over 1941, the previous peak. During the first ten months of the year, production jumped from 3,782,000 barrels per day in January to 4,400,000 in October. Available data for the last two months of the year indicate a leveling off of this trend, with daily rates slightly above 4,400,000 barrels.

Jan 1, 1944

By N. O. Gray, John Henderson

Hydrogen-reduction data for naturally occurring single crystals and Prepared polycrystals of dense hematite have been presented. Results cover the temperature range 400o to 1000oC, for particles from ten sources, ranging in size from 0.07 to 10 mm and in shape from spheres to cylinders, cubes, and thin slabs. A consistent pattern of behavior has been demonstrated for single crystals and the reduction mechanism shown to be temperature-dependent. Below 579oC reduction is a simple topochemical process but at higher temperatuves it is complex and occurs in two distinct stages. Prepared particles from these laboratories behave in a similar manner to the single crystals. Data from two investigators showing topochernical reduction of Prepared particles above 575°C are inconsistent with that for other dense hematites. It is concluded that topochenzical reaction should not be used as a model for generalized rate expressions for dense hematites. SINCE 1958, McKewan1-6 has brought to prominence a simple concept of dense hematite reduction. This model is that oxygen is lost from a hematite particle undergoing reduction only from an oxide-iron interface that recedes in such a way that the oxide remaining retains the original shape of the particle, i.e., reduction occurs topochemically. An adjunct to this concept is that any intermediate oxides in the transition from hematite to iron only form thin layers so that oxygen cannot be lost from the particle without movement of the oxide-iron interface. Further, the rate of oxygen loss from the particle is said to be proportional to the area of the receding interface so that the iron layer grows linearly with time and the over-all reduction process can be described by the equation where ro and do are the initial particle radius and density, respectively, R is the fraction of the original oxygen lost, i.e., the fractional reduction, at time t, and K is the rate constant. The idea of an underlying simplicity in hematite reduction is attractive because it gives a tractable basis from which general theories of hematite reduction can be developed and it has received wide support,7-14 based mainly on the large amount of data13 that can be fitted to Eq. [I]. However, despite the fact that this equation has been derived for dense materials, the bulk of the data that have been used to test it13 have been for materials of only about 90 pct of theoretical density (5.26 g cm-3) or less, so that its generality for dense hematites has not been demonstrated. In any case, as will be seen, adherence of reduction data to Eq. [1] does not necessarily imply that reaction occurs topochemically. In this work only data for hematites approaching theoretical density are considered and it will be shown that in only one study besides McKewan's is topochemical behavior observed over the whole range of temperature investigated. For the majority of materials a linear rate of interface advance is observed to complete reduction only when wustite is not a stable intermediate phase in the transition of hematite to iron, i.e., at temperatures below about 575°C. Above this temperature, reduction is an exceedingly complex series of reactions that takes place in two distinct stages and it is only in the first stage that reaction in any way resembles a topochemical process. This means then that, far from representing general behavior as has commonly been supposed, topochemical reaction for dense hematites is only a particular behavior that may be observed under some circumstances. EXPERIMENTAL Hydrogen-reduction data have been collected and cross-checked in these laboratories by three techniques, weight loss, collection of water evolved in the reduction reactions, and direct metallographic examination. Details of these techniques are discussed elsewhere," where it is shown that results obtained by the three methods are in close agreement. The weight-loss method, by which most of the results were obtained, consisted of hanging the sample in a platinum mesh basket from an Ainsworth Model AV-AU-1 vacuum recording balance inside a vertical l 1/4-in.-ID alumina tube furnace. Dry deoxidized hydrogen was flowed downwards through the tube at 2 to 4 liters min-1 (stp). Single crystals from two sources and artificial oxides from three sources have been examined. The single crystals were from hematite deposits at Yampi Sound, Western Australia, and Brazil, the latter being obtained from Gregory, Bottley and Co., London, U.K. The "Yampi Blue" crystals were hand-picked from washed, magnetically concentrated, sized fractions, -200 mesh BSS (mean diameter ca 0.07 mm) and —36 + 44 mesh BSS (mean diameter ca 0.4 mm) while 10-mm cubes were cut from the Brazilian crystals with a diamond saw. The starting materials for the prepared particles were hematites designated, respectively, "Specpure Iron Oxide", Laboratory No. S639 from Johnson Matthey & Co. Ltd., London, U.K., "Calcined Ferric Oxide" from B.D.H. Laboratory Chemicals Division, Poole, U.K., and "Pigment Grade Oxide", EPR-50, from C. K. Williams & Co., Easton, Pa., U.S.A. Approximately spherical particles were prepared from the artificial oxides by rolling the material, moistened if necessary, in a glass jar, and cylindrical compacts approximately 10 mm in diam and of approximately equal height were pressed in a steel die at 200 psi. These spheres and cylinders were subsequently fired in oxygen for 20 to 100 hr at 1370°C. The

Jan 1, 1967