Search Documents

By B. B. Rath, Hsun Hu

Rates of migration of large-angle boundaries have been studied in zone-refined aluminum crystals, defonned 80 pct by rolling in the (110)[112] orientation at -78°C followed by a recovery anneal at 80°C. Artificially nucleated grains show a marked variation. by an order of magnitude, in their growth rates in different directions. The average activation energy for the migration of all boundaries was found to be about 16,000 cal per mole. The anisotropy of the boundary migration is rationalized on the basis of the boundary structure. It has been observed by Beck and HU,1 Kohara el al,2,3 and Czjzek and Haessner4 that recrystallized grains formed upon annealing Of deformed sing1e crystals of aluminum show anisotropic growth characteristics. Kohara et al. found that single crystals rolled in the (110)[112] orientation, when random nuclei were provided on one side of the crystal by rubbing with emery paper and annealing, developed a sharp recrys-tallization texture on the other side of the crystal upon further annealing. This sharp recrystallization texture consisted of four components, which were related to the deformation texture of the crystal, i.e. (110)[112], by rotations of ±40 deg around each of the two common [ 111] axes' They also noted that recrystallized grains were elongated in directions perpendicular to either of these two common [1111 axes. They attributed this anisotropic growth to the difference in the rate of self-diffusion or diffusion of impurity atoms along the tilt and the twist boundaries. A somewhat similar investigation was conducted by Czjzek and Haessner4 On strained single-crystal sheets Of alum- inum. These authors claimed that the matrix structure of the deformed crystal had a greater effect on the growth anisotropy of the recrystallized grains than did the boundary orientation itself. In the present investigation quantitative measurements of the rate of grain boundary migration in anisotropic growth have been made in zone-refined aluminum (99.9999+pct pure) crystals deformed 80 pct by rolling in the (110) 112] orientation. Crystals of this particular orientation were chosen because of the following desirable features: 1) the crystal does not change its orientation during rolling; 2) the rolling plane contains all the significant crystallographic directions; and 3) when annealed, following deformation, the crystal does not re-crystallize spontaneously but polygonizes to a stable and homogeneous structure. Hence, the initial orientation of the crystal and a constant strain energy in the matrix can be maintained during subsequent grain boundary migration studies. It is essential to keep the driving force constant for the study of boundary mobility.5 EXPERIMENTAL PROCEDURE A cylindrical single crystal of 1 in. diam was grown by the Bridgman method in a high-purity graphite mold. The resistance ratio, R(4.2°K) /R(298°K) , of the grown crystal was approximately 2.0 x 10-4. A number of slices, 1/4 in. thick, were cut from the crystal along the (110) plane and were mechanically and electrolyti-cally polished to remove the strained surface layer. The crystals were then rolled along the [112] direction to 80 pct reduction in thickness at -78°C. To minimize surface friction, the crystals were rolled between two layers of 0.005-in. teflon sheet. Rolling was interrupted, prior to completion, to remove the surface layers and the edges by electropolishing. These and similar precautions in handling the rolled crystals

Jan 1, 1967

By W. J. Leas, L. A. Rapoport

As a preliminary, consicleration is given to the conventional definition of relative permeability and to the conditions governing the simultaneous flow of oil and gas through porous media. For the conditions of flow prevailing throughout most of a gas drive reservoir, the oil and gas can reasonably be supposed to be in capillary equilibrium with each other. Under these conditions, and these conditions only, the relative permeability to liquid can be expressed as a function of saturation. The relative permeability to liquid in that case is dependent upon the distribution of fluids which itself is shown to be related to the capillary pressure, and, in turn, to the saturation. As a consequence, relative permeability to liquid can be expressed in terms of the volume and surface area of a network of liquid channels bounded by the rock and the gas phase. While the volume of this network can be evaluated accurately, the surface area cannot. However, for any such volume, maximum and minimum values of the corresponding surface area can be calculated from capillary pressure data. It is then possible to establish for any saturation the limits within which the value of the relative permeability to liquid must lie. As a consequence of the theoretical development, the validity of an experimental method for measuring relative permeability to liquid which utilizes a stationary gas phase is demonstrated. In this method capillary barriers are cemented to the ends of the core sample to permit the maintenance of capillary equilibrium between the two phases. At the same time, this procedure eliminates undesirable secondary phenomena such as end effects, fissure effects, etc., the presence of which adversely affect the results of other laboratory methods. The results obtained by theoretical calculations, and experimentally, are discussed. In view of the overall precision that can presently be obtained in reservoir calculations, the agreement between the calculated and measured relative permeability to liquid data can be considered satisfactory. In conclusion, for reasons of economy and simplicity, the procedure of calculating limiting relative permeability to liquid curves from capillary pressure data is indicated for general engineering purposes. It is shown that the above procedure can easily be extended to the cases where connate water is present. Its use for reservoir studies is particularly recommended in conjunction with the method for measuring relative permeability to gas' which simultaneously yields the capillary pressure data necessary for the calculations. THEORETICAL Definition of Relative Permeabilities — Basic Equations for Heterogeneous Flow The equations by which the relative permeability concept is defined and upon which the formulation of all of the gas-oil flow problems rests at the present time are expressed as: V, = — Grad PL = — Grad PL ....(la) PL µL, k k KG VG = —K - Grad PG k- Grad Pc .... (lb) Mo where ,. and G refer to liquid and gas; V is the volumetric rate of flow per unit gross area. µ the viscosity, Grad P the potential gradient. and k the specific permeability of the porous medium.* (For horizontal flow, Grad P becomes the pressure gradient; otherwise, gravity must be included.) According to these expressions, each of the constituent phases is considered similar to a homogeneous system where the volumetric rate of flow is proportional to the pressure gradient, and for each of which the constants of proportionality, k, and kG, are termed effective permeabilities. by analogy to the specific permeability as defined by Darcy's law in its original form. In order to obtain a convenient basis of comparison, the effective permeabilities are referred to the specific permeability, k, of the considered porous medium, with the help of the relations: k1. = KI. k kQ = Kn k..........(2) K,. and Kr. are defined as the relative permeabilities to the liquid and to the gas phase respectively, and frequently expressed in per cent of specific permeability. It may be seen that Equations (1); which appear to be a direct generalization of Darcy's law, correspond to the assignment at any given time of a set of "local" permeabilities to each point of the porous medium, and represent in a differential form the two fluid flow system as a simple superposition of the individual single flow systems. The above interpretation implies that the effective or relative permeabilities are independent of pressure or rate of flow,

Jan 1, 1951

By L. A. Rapoport, W. J. Leas

As a preliminary, consicleration is given to the conventional definition of relative permeability and to the conditions governing the simultaneous flow of oil and gas through porous media. For the conditions of flow prevailing throughout most of a gas drive reservoir, the oil and gas can reasonably be supposed to be in capillary equilibrium with each other. Under these conditions, and these conditions only, the relative permeability to liquid can be expressed as a function of saturation. The relative permeability to liquid in that case is dependent upon the distribution of fluids which itself is shown to be related to the capillary pressure, and, in turn, to the saturation. As a consequence, relative permeability to liquid can be expressed in terms of the volume and surface area of a network of liquid channels bounded by the rock and the gas phase. While the volume of this network can be evaluated accurately, the surface area cannot. However, for any such volume, maximum and minimum values of the corresponding surface area can be calculated from capillary pressure data. It is then possible to establish for any saturation the limits within which the value of the relative permeability to liquid must lie. As a consequence of the theoretical development, the validity of an experimental method for measuring relative permeability to liquid which utilizes a stationary gas phase is demonstrated. In this method capillary barriers are cemented to the ends of the core sample to permit the maintenance of capillary equilibrium between the two phases. At the same time, this procedure eliminates undesirable secondary phenomena such as end effects, fissure effects, etc., the presence of which adversely affect the results of other laboratory methods. The results obtained by theoretical calculations, and experimentally, are discussed. In view of the overall precision that can presently be obtained in reservoir calculations, the agreement between the calculated and measured relative permeability to liquid data can be considered satisfactory. In conclusion, for reasons of economy and simplicity, the procedure of calculating limiting relative permeability to liquid curves from capillary pressure data is indicated for general engineering purposes. It is shown that the above procedure can easily be extended to the cases where connate water is present. Its use for reservoir studies is particularly recommended in conjunction with the method for measuring relative permeability to gas' which simultaneously yields the capillary pressure data necessary for the calculations. THEORETICAL Definition of Relative Permeabilities — Basic Equations for Heterogeneous Flow The equations by which the relative permeability concept is defined and upon which the formulation of all of the gas-oil flow problems rests at the present time are expressed as: V, = — Grad PL = — Grad PL ....(la) PL µL, k k KG VG = —K - Grad PG k- Grad Pc .... (lb) Mo where ,. and G refer to liquid and gas; V is the volumetric rate of flow per unit gross area. µ the viscosity, Grad P the potential gradient. and k the specific permeability of the porous medium.* (For horizontal flow, Grad P becomes the pressure gradient; otherwise, gravity must be included.) According to these expressions, each of the constituent phases is considered similar to a homogeneous system where the volumetric rate of flow is proportional to the pressure gradient, and for each of which the constants of proportionality, k, and kG, are termed effective permeabilities. by analogy to the specific permeability as defined by Darcy's law in its original form. In order to obtain a convenient basis of comparison, the effective permeabilities are referred to the specific permeability, k, of the considered porous medium, with the help of the relations: k1. = KI. k kQ = Kn k..........(2) K,. and Kr. are defined as the relative permeabilities to the liquid and to the gas phase respectively, and frequently expressed in per cent of specific permeability. It may be seen that Equations (1); which appear to be a direct generalization of Darcy's law, correspond to the assignment at any given time of a set of "local" permeabilities to each point of the porous medium, and represent in a differential form the two fluid flow system as a simple superposition of the individual single flow systems. The above interpretation implies that the effective or relative permeabilities are independent of pressure or rate of flow,

Jan 1, 1951

By A. E. Dwight, A. F. Berndt

ThE published U-Ru equilibrium diagram indicates the existence of six intermetallic compounds in this system.' The structure of only two of the compounds, u2Ru2,3 and URU3,4 have been identified. This communication reports on the crystal structure and density of Uau3, which is formed by a peritectoid transformation at 1025° ± 5°C: U3Ru4 + U3Ru5 = U2Ru3. An alloy with the stoichiometric formula U2Ru3 was prepared by arc melting electrolytic uranium and ruthenium of 99.9 pct purity on a water-cooled copper hearth under an argon atmosphere. After homo-genization at 1000°C for 3 days, a metallographic examination revealed that the peritectoid transformation was complete and less than 5 pct of a second phase was present. A powdered sample, obtained by crushing the brittle compound, was annealed for 1 hr at 1000°C and air-cooled. Debye-Scherrer patterns were obtained with filtered CrKa, FeKa, CoKa, or CuKa radiation. The X-ray patterns of U2Ru3 weFe indexed as an fcc structure with a. = 12.895 0.00lA. The unit-cell constant and its standard deviation were calculated by a computer program described by Mueller, Heaton, and Miller.5 The density, measured by an immersion method, was 14.45 g cm-3. A calculated density of 14.48 g cm-3 was obtained on the assumption that twenty-four formula units (120 atoms) comprise a unit cell. The space group is either oh7 Fd3m, or the less symmetric, T4h, Fd3, since reflections indexed as hk0 with h + k + 4n are absent. All values of h2 + k2 + 12 permitted by both space groups are listed in Table I together with dc, do, and I. values. The calculated d spacings were obtained by the computer program of Mueller, Meyer, and simonsen.6 The observed d spacings above 0.77A were obtained from X-ray" patterns prepared with CuKa radiation, above 0.90A with CoKa radiaaion, above 0.98A with FeKa radiation, and above 1.16A with CrKa radiation. An attempt was made to identify the crystal structure of U2Ru3 by comparison with published data on other A2B3 compounds. A recent compilation7 of intermetallic compounds lists thirty-two structure types with the A2B3 stoichiometry. Only two of the structure types are fcc and they are Sb2O3(r), senarmontite, with 16 Sb2O3 per unit cell, and In2Te3 for which several structures have been proposed.8 However, the two cases cited do not have twenty-four formula units in the unit cell. We therefore, cannot identify UPRU3 with any of the other known A2B3 compounds. Ternary alloys were made in which 5 at. pct Os, Rh, or A1 were substituted for 5 pct of the Ru in U2Ru3. The osmium substitution increased the unit cell constant to 12.899 * .001A, which is to be expected since the atomic volume of osmium is slightly larger than

Jan 1, 1969

By Lars Rossemyr, Terkel Rosenqvist

The equilibrium Mn + 2 IiCl = MnCl2(g) + H2 has been studied at 1090°C for pure manganese and for Mn-Si alloys. For this reoction a standard free energy of Fo1363, = - 19,700 i 300 col ioas found. Combined with other thermal data, the standard free energy of the reaction Mn(s, ß) + Cl2 = MnCl2(g) was derived: Fo=- 56,140 + 9.78 T log T - 40.10 T For the formation of the various manganese silicides the following free energies were obtained. 5 Mn + 3 Si - M1z5Si3 ?F°1363 = -41,500 i 1500 cal Mn + Si - h.lnSi ?F°1363= -10,000 i 500 cnl Mn + 2 Si = MnSiz ?F°1363= -11,500 ± 500 cal In the search for a method suitable for the study of thermodynamic properties of certain alloy systems, it was found that the heterogeneous equilibrium between the alloy and a gas mixture consisting of hydrogen chloride, hydrogen, and volatile metal chlorides has considerable advantages. In addition to giving thermodynamic information about the alloys, such measurements may be used to derive thermodynamic data for the volatile metal chloride itself. The present paper gives some results which were obtained for manganese silicides and manganous chloride. Similar studies are presently being carried out for the iron silicides. The phase diagram of the Mn-Si system is rather well known,' but no information exists to the authors' knowledge about the thermodynamic properties of manganese silicides or about the chemical activities in molten Mn-Si alloys. At elevated temperature, manganese may react with hydrogen chloride according to the equation: Mn(s, ß ) + 2 HC1 = MnC1, (g ) + H2 [ 1] with the equilibrium constant The value of K, may be determined from measurements of the gas composition in equilibrium with pure manganese. When this value is used in connection with measurements on manganese alloys, the chemical activity of manganese in the alloy may be derived. Initial calculations showed that around 1000" to 1200°C the equilibrium constant K1 has a value of a few thousand, i.e., the reaction is shifted far to the right. In order to study this rather unbalanced gas composition, a flow method was used in two slightly different modifications. For all experiments with manganese silicides and for some experiments with pure manganese the apparatus shown on Fig. 1 was used. A bed of the metal or alloy was placed in a tube furnace. The refractory tube had an internal diameter of 14 mm and the bed was 75 mm long. Electrolytic manganese of high purity and silicon, 99.95 pct Si, were used as raw materials. All alloys were prepared by melting weighed amounts of the elements in a high frequency induction furnace in argon atmosphere. The melting was done in a silica crucible which was placed inside a graphite shell. The alloys were crushed to - 10 +40 mesh and analyzed chemically. Also, for the pure elements, the same size fraction was used. A controlled gas mixture of purified hydrogen and from 3 to 12 pct HC1 was passed through the bed where it reacted with manganese according to Eq. [I]. The volatile manganese chloride was collected in a condenser placed in the cooler part of the furnace tube. The gas mixture before and after the furnace was sampled and analyzed by absorption of

Jan 1, 1962

By A. N. Mitinsky

(San Francisco Meeting, September, 1915) THE theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are, proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,1 that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably clue to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually -assumed, though incorrectly, that the proportional limit is determined by the ultimate -strength. In Germany the point at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both 'be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved-or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining. the elastic limit by alternately loading and unloading

Jan 8, 1915

By Laurance Reid

HIGH compression ratios, resulting from high injection pressures and relatively low recovery process pressures, constitute a major problem, which has confronted those engaged in gas recycling for condensate production since the beginning of that practice. Despite the numerous process developments and improvements, no entirely satisfactory solution for this prob-lem has been presented to date. Often, where the residue gas from the recovery process must be recompressed for subsurface injection, there is a substantial difference between the required injection pressure and the plant-operating pressure required to produce maximum recovery of condensate. These limitations result in high compression ratios, which, in turn, neces-sitate excessive compressor investment and operating cost. As an alternative, the operating pressure may be increased in order to lessen the compressor requirements but such a saving often is purchased at the expense of decreased condensate recovery, caused by operation at the higher pressure. Regardless of the choice, the net result is a diminished return on the capital invested in the project. The goal of future development in this field must be the complete recovery of all valuable hydrocarbon components in the reservoir fluid at pressures that, regarded as compressor suction pressure, will require minimum compressor horsepower to inject the residue gas into the formation. A com-pression ratio of 1.5 has been established as an optimum for modern compressor equipment." Therefore, in order to con-form to this optimum condition, a 3000-lb. injection pressure would require that the condensate recovery process be operated at 2000 lb. per sq. inch.

Jan 1, 1940

By J. R. Bell, W. J. Childs, J. H. Bucher, G. A. Wilber

A technique for determining recrystallization times as short as 0.10 sec was developed utilizing the "Gleeble", a commercially available testing system designed for the study of short-time, high-temperaLure themal and mechanical processes. The procedure consisted of heating a small tensile specimen to a given temperature of hot deformation, loading to a given reduction in area, unloading, delaying various intervals at temperature, and then reloading- to failure. The magnitude of the ultimate load obtained upon reloading decreased with delay lime as recrys-lallization proceeded. The technique was applied to austenite recrystallization in AISI 1010 and AISI 1010 uith 0.02 pct Cb steels. For each steel the reduction in area given the specimen on the first pull was mainlairred at 30 ± 5 pct and recrystallization times deterntined at various temperatures. The results indicaled a significantly slower rate of recrystallization for the columbium-modified composition, suggested the presence of- a recovery stage in the softening process , and indicated a greatly increased softening rate at a temperatuve where significant allotropic transformation to a partially ferritic Structure could occur. In recent years increasing attention has been paid to the fact that the process of recrystallization of austenite deformed at elevated temperatures is far from instantaneous at many practical hot-working temperatures.1-3 This realization has given rise to such terms as hot cold-working1 or warm-working,2 These terms generally describe processes where the recrystallization rate at the temperature of deformation is slow enough to have an appreciable effect on mechanical properties despite a relatively high deformation ternperature. The mechanical properties of interest can be either the properties at the deformation temperature as in hot-workability studies4 or the room-temperature properties after cooling as in the many recent studies of various thermomechanical processes172 where heat treatment and deformation are intentionally combined to give a unique set of room-temperature properties. Because of this interest in processes where the austenite recrystallization kinetics can be an important variable, the development of quantitative methods of following the course of short-time, high-temperature recrystallization has received increasing attention.l,3,5 The experimental methods to date have, in general, relied upon rapidly deforming the austenite, holding at temperature for various brief intervals, quenching as G.A.WILBER and W. J. CHILDS, Members AIME,are Research-Fellow and Professor, respectively, Rensselaer Polytechnic Institute, Troy, N. Y. J. R. BELL and J. H. BUCHER, Member AIME, are Research Engineer and Research Supervisor, respectively, Graham Research Laboratory, Jones & Laughlin Steel Co., Pittsburgh, Pa. Manuscript submitted March 13, 1968. IMD. rapidly as possible, and then using room-temperature measurements to follow the recrystallization process. Although such methods can be successfully applied to certain alloy steels, the existence of the allotropic transformation during cooling of plain-carbon or low-alloy steels tends to obscure the results. Thus, such room-temperature measurements as hardness and X-ray line widths do not correlate well with the extent of austenite recrystallization before quenching,5 and results based on room-temperature microstruc-tural observations are dependent upon the success in correlating the observed structure with the prior aus-tenitic grain structure.1,3,5 The purpose of the present work was to develop a quantitative method for the determination of short-time, high-temperature recrystallization rates, based on measurements made at the temperature of deformation. EXPERIMENTAL TECHNIQUE The basic technique consisted of heating a small tensile specimen to a given temperature of hot deformation, loading to a given reduction in area, unloading, delaying various intervals at temperature, and then reloading to failure. The data were obtained in the form of traces of load and elongation as a function of time. Due to the high deformation temperature, the strain hardening introduced during initial loading was progressively annealed out with holding time after unloading and the loads obtained upon reloading decreased as this softening proceeded. Although the value of the second load at any Consistent point On the load-elongation curve could have been used as a measure of the degree of softening, the most convenient to use was the ultimate load. The softening indicated by the decrease in the second ultimate load with time is essentially a process of annealing of cold-worked material at a high deformation temperature. Although some recovery grain growth may contribute to such a softening process, it is generally considered that the major softening which must take place to achieve complete removal of substantial Strain hardening will occur by the formation of new, stress-free grains. As the results of this work indicate that essentially complete removal of strain hardening did in fact occur. the primary softening process will be attributed to recrystallization, and specific reference made where it appears that other mechanisms may be contributing to the total observed softening. It would, of course, be of interest to attempt to correlate the results of this work with the actual austenite fraction recrystallized as determined by other techniques. This was not attempted in the present work because it would have required running a large number of additional specimens and, as discussed previously, there is limited assurance that the results would accurately reflect the prior austenite fraction recrys-

Jan 1, 1969

By C. R. Sandberg, L. S. Gournay, R. F. Sippel

The effect of fluid-flow rate and fluid viscosity on oil-water relative permeability determinations was studied using the "dynamic flow technique." In this work relative per-nleability curves were obtained for homogeneous small core .samples from several sandstorle outcrop form-utions. Radio-tracers were used for the determination of fluid saturation and for the detection of saturation gradients. Cobalt-60 in the form of cobaltous chloride was used as a water-phase tracer in some of the experiments. Iodine-131 in the form of iodobenzene and Mercury-20-3 in the form of mercury diphenyl were used as oil-phase tracers in other experiments. Flow rates for each phase were varied within a range of 2.5 to 140.6 ml/hr. Oil-phase vis-cosities under flowing condition,> were varied from 0.398 to 1.683 cp. The relative permbilities ob-tained were found to he solely a function of saturation and independent of flow rare, provided there was no .Saturation gradient induced in the core sample by "boundary effect." Even though equilibrium with re-sped to flowing conditions was obtained at the lower flow rates, where a saturation gradient exists, this equilibrium is of a "contingent"-type rather than the "steady-state" equi-librium implicit in the relative per-meability concept. The only effect of increasing the oil or non-wetting phase viscosity was to decrease the flow rate required for the elimina-tion of the boundary effect. Fairly good agreement between experimentally determined and calculated values of the boundary effect was obtained when the non-wet-ring oil phase was the only Flowing phase. INTRODUCTION In the characterization of reservoir rock, as well as in the solution of reservoir production problems, it is most desirable to have reliablc rela-tive permeability measurements for the rock and fluids of interest. Many techniques have been developed for the laboratory determination of the relative permeability of both large and small core samples. In varying degree, difficulties attend the use of all of the methods. Each of the methods requires the metered flow of fluids of known viscosity through the core sample under conditions wherein the pressure drop in the individual flowing phases can be measured or closely approximated. Since the relative permeability is a function of the saturation and distribution of the flowing fluids, some means of obtaining such information is also required. The laboratory determination of the relative permeability of a sample should give the same relative permeability saturation relationship that would exist if the sample were in place in the oil reservoir. The attainment of this objective is complicated by the fact that the use of small core samples for laboratory measurements is usually necessary. As a result, errors in measuring the relative permeability arise from boundary effects at either the fluid input or output ends of the sample; no significant boundary effect is anticipated at the sides of the sample normal to direction of fluid flow. At the input end of the sample a boundary effect exists if the flow fluids are not com- mingled as they would be in the reservoir. At the output end of the sample a boundary effect exists as a result of discontinuity of the capillary properties of the system. Here the flowing fluids leave the small flow channels and enter a collecting system having much enlarged flow channels. Thus, there is a tendency for the wetting phase to be retained by the core sample because of the attraction of the core sample for the wetting fluid. No reference is made to these boundary effects in either Darcy's equation or in the relative permeability concept. As a consequence the saturation effect peculiar to the input end of the core sample may cause an error in the effective permeability measurement, since some portion of the core sample must be utilized for commingling of the flow fluids. At the output portion of the core sample a saturation gradient or a saturation change along the axis of flow results. Since relative permeability is a function of fluid saturation, this saturation gradient may cause a variable permeability measurement, especially since extent and character of the saturation gradient can vary with fluid-flow rate. The most convenient method of minimizing the boundary effect, especially at the output end of the sample, is to flow the fluids of interest through the core sample at such high rates that the capillary forces arc insignificant as compared to the viscous forces involved in the fluid flow. Since recent work of a preliminary nature has indicated that fluid dispersion in the porous medium increases with the flow rate, the high flow minimizes the boundary effect at the input end of the core sample by enhancing the mixing of the fluids.

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By Elmer W., Pehrson

NOT much serious consideration was liven to the military aspects of raw materials before World War 1. Following the outbreak of war in Europe in 1914, however. this situation was promptly changed. Disruption of allied shipping and German submarine warfare soon cut off a substantial part of the material the United Staten was accustomed to receiving from overseas. At the same time, raw material requirements rose rapidly as the tempo of industrial preparedness was stepped up in anticipation of war. By April 1917, when we entered the war, serious shortages threatened and consideralde attention was being given to our "deficcient" raw materials. The term "war mineral," began to appear after we became active combatants. But there is no evidence that "strategics" and "critical." as now used, had entered the lexicon of our raw materials experts during the last war nor were there apparently any officially recog¬nized list or definitions of what con¬stituted war materials. According to G. A. Roush in his book, `'Strategic Mineral Supplies," C. K. Leith, while serving as mineral advisor to the War Industries Board. compiled the first unofficial list of deficient minerals in 1917.

Jan 1, 1944

By Walter R. Crane

PAGE I. Apparatus and Methods.......... 406 1. The Magnetic Circuit...........406 2. Apparatus Employed in the Traction-Method...... 406 a. The Coils............409 b. The Pole-Pieces..........409 3. Methods of Testing Fields Produced by Different Pole.Pices.. ..409 c. Testing with a Search.Coil........410 d. Testing with Iron-Filings and Glass Tube.. .. .410 4. General Forma of Pole-Pieces.........411 e. Flat Poles............411 f. Conical Poles........... 411 g. Spherical Poles...........411 h. Chisel-Edged (Chamfered) Poles.......412 II. Magnetic Fields...........412 5. Methods of Testinq for Magnetic Permeability...... 421 i. The Rod-Method..........423 j. Method Employed in These Experiments......424 k. Difference in the Results of the Two Methods..... 425 l. The Traction-Method.........427 m. Effect of Loosening the Charge.......430 n Corrections...........432 6. Theory.............433 o. Effect of Varying Weight on Tractive Force..... 434 p. Effect of Varying Pole-Distance.......436 q. Effect of Varying Magnetization.......436 T. Effect of Varying Size.. .......437 a. Summary,........... 441 III. The Relative Magnetic Permeability of Various Minerals,. 443 The form and strength of magnetic fields have attracted much attention. especially in connection with the designing of dynamo-electric machinery—an art which has been revolution-

Jan 1, 1902

By H. Foster Bain

Jan 1, 1910

By W. Rostoker

PART of a program of research on the Ti-A1 system1 involved a study of the lattice parameters of the titanium-rich a solid solution, which has a hexagonal close-packed structure. For this work, a 14 cm Debye-Scherrer powder camera and filtered CuK, radiation was used. For each pattern, the parameters were calculated by a least squares solution of the five strongest high angle lines. This provides an accuracy of i0.005A or better. The results are shown graphically in Fig. 1. It will be seen that an unusual change of slope occurs in the curve for the C parameter at high aluminum contents. Such anomalous changes in slope have been recorded by RaynorV or several magnesium-rich solid solutions. The effects were interpreted in terms of a special contribution to the lattice distortion due to factors of electronic origin predicted by Jones." Jones' theory, in substance, suggested that an unusually large expansion of the lattice would begin when the electron per atom concentration in the alloy was increased to a value at which an overlap just began from one Brillouin zone to another. Con-

Jan 1, 1953

By W. D. Robertson, Raymond C. Boettner

A study was made of the change in density during the first (transient) and second (linear) stages of the creep curve of polycrystalline copper as a function of 1) stress, 2) temperature, 3) plastic strain, 4) impurity and atmosphere effects, and 5) structure, including single crystals. Voids were not observed in single crystals strained 15 pct at 500°C, or in a polycrystal-line aggregate produced by recrystallizing a single crystal, within the limit of sensitivity, Ae/e = 1 x 10-4. It appears that voids are heterogeneously nucleated at grain boundaries by an insoluble phase, or phases, which can be removed by directional solidification. The principal controlling mechanism of void growth appears to be condensation of vacancies at grain boundaries. Vacancies are transported to a boundary and condense as a consequence of the tensile stress component across the boundary, which depends on the orientation and configuration of the boundary plane and on boundary shear across ledges and other irregularities. The ultimate source of vacancies is the free surface and diffusional transport is by way of the boundary plane. PREVIOUS investigations have dealt with the nucle-ation of voids at grain boundaries under creep condition~'-~ and with the connection between grain boundary voids and subsequent brittle fracture.5-7 Growth of voids during the creep process, particularly in the transient and linear stages of creep, has not been studied with the same intensity. Therefore, it seems pertinent to investigate the process of void growth with respect to the related creep curve, and the morphology of growing voids with respect to the structure.

Jan 1, 1962

[FUQUA, H. B. and Thompson, B. E.: Oil and Gas Development and Production in North Texas for 1933, 107, 320; for 1934, 114, 417 Oil and Gas Development in West Texas 114, 438 FURMAN, W. F.: Heat and Corrosion-resisting Alloys. Printed in Oil & Gas Jnl., June 13, 1935 Furnace-bottom sand, uniformity, 73, 390 Furnace control, Isley apparatus, M27, 502 Furnaces (See also Holt-Dern; Blast Furnaces; Roasters; Wirebar, etc.): annealing: electric, 89, 424 gas-fired, 89, 425 gas vs. wood for nonferrous metals, 89, 422]

Jan 1, 1936

By E. M. Wise

IT is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. CONCLUSIONS 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportional limit, very low; elongation, 37.5 per cent in 2 inches. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545° and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or no grain growth resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times.

Jan 1, 1940

By James R. Cudworth

OUR colleges and universities have met many difficulties during the past year. From a period of small enrollments and depleted faculties, the educational institutions have passed quickly to a period of the largest enrollments in their history with inadequate facilities and staffs. The results of the shortsighted policy of the Selective Service system which drained the technical schools and universities of many of the students who were potential teachers are now being felt. The movement of faculty members into positions in industry during the war years has resulted in many of them forsaking permanently the educational field for the higher salaried positions they now occupy. Competition is keen between the educational institutions, and between the institutions and industry, for technically trained men. Dean Holbrook's statement in last year's annual review that he thought it would take three or four years to restore our engineering departments to their former level in quality of instructors is even more convincing today. Somehow, the institutions must not only reach their former level in quality of instruction but they must also increase the quantity of their staffs to meet the demands of the ex-service men and the high school graduates for engineering education. The enrollments in the mineral industry fields of mining, metallurgical, geological, petroleum, and ceramic engineering, although greatly increased, are not expanding as much as in the more widely known fields of electrical, mechanical, aeronautical, and civil engineering. In fact, many educators are tremendously worried about the segregation of so many young men in a relatively few fields while the needs of others will remain unanswered.

Jan 1, 1947

By Carle R. Hayward

The growing importance of metallography has caused a corresponding interest in the improvement of apparatus for preparing specimens of metals and alloys for microscopic examination. The purpose of this paper is to describe an electric heating-furnace, a grinding- and polishing-machine, and a device for mounting specimens, which are used in the metallographical work at the Massachusetts Institute of Technology. These three pieces of apparatus were designed and made in the laboratory of the Institute, and each possesses some original features which may be of interest. Electric Heating-Furnace. The accurate control of heat necessary for metallographic work is best obtained by the electric-resistance furnace. Uufortunately, however, even the platinum-wound furnaces cleteriorate with use and ultimately burn out, while the cheaper resistance-materials are often short-lived. Since the resistance-coil must be replaced from time to time, it is of advantage to be able to make this change with as little trouble as possible, and this is an important feature in the furnace shown in Fig. 1. A is a cylindrical galvanized-iron can, with two handles, B. A porcelain tube, C, passes through the central hole in the cover of the can and rests upon the asbestos disk, D; the bottom of the tube is held in place by the asbestos ring, 3. The space, F, around the tube is filled with powdered magnesia. G is an ordinary assay-crucible, with the cover inverted so as to present a smooth top for supporting a second porcelain tube, H. The latter is wound with " Excello " resistance-tape, 0.014

Jan 1, 1912