Search Documents

By Neils Hansen

The microstructure of dispersion-strengthened aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum oxide has been examined by optical and transmission electron microscopy, and the flow stress has been determined at room temperature and at 400C by tensile testing. Products were examined as recrystallized and as high-temperature extruded, and the microstructures consisted of a fine dispersion of oxide particles in a matrix divided by respectively recrystallized grain boundaries and subgrain boundaries. The flow stress (0.2 pct offset) at room temperature of recrystallized dispersion strengthened aluminum aluminum-oxide products is the superposition of dispersion strengthening and grain boundary strengthening. This superposition has been found to be linear. The flow stress (a) can be related to the grain size (t) by the Petch equation: ing content of oxide and k is a constant independent of the oxide content. For extruded products a similar relation has been found by replacing the grain size by the subgrain size. The k-value is of the same order for the two types of structure, which shows that the subgrain boundaries are as effective slip barriers as grain boundaries. Tensile testing at 400C of re-crystallized and extruded products shows that oxide dispersion strengthening is very effective, whereas the strengthening effect of grain boundaries and subgrain boundaries is small. THE microstructure of dispersion-strengthened products consists of hard particles finely distributed in a metal matrix. The strengthening effect of the dispersed phase has been fairly well established,1 and it has been found that the size and volume fractions of the dispersed particles are important structural parameters. However, in many dispersion-strengthened products which have been worked and heat-treated during manufacture the matrix is divided into well-defined grains or sub-grains, which may also have a strengthening effect. A model of the matrix strengthening in dispersed products worked during manufacture has been proposed,2 introducing the energy of the structure as a strengthening factor, especially at low temperatures. A difficulty in this model is, however, to relate this (stored) energy to the structural parameters directly observable as for instance grain size. The strengthening effect of the matrix grain size after recrystallization has been in- vestigated for nickel-thoria (TD-Nickel) products3 and for copper aluminum-oxide products. Conclusive results were, however, not obtained as the grain size of TD-nickel was constant. 5 to II , after recrystallization at temperatures from 700 to 1200°C and as the copper products containing 5 to 1 wt pct of aluminum oxide could not be recrystallized even after severe cold reduction and heat treatment at 1050C. For aluminum aluminum-oxide products containing from 1 to 5 wt pct of aluminum oxide it has been shown that the tensile strength at room temperature decreases when an extruded product is cold-worked and recrystallized. The matrix in the extruded products is divided into well-defined subgrains of micron size, and as the grain size of the recrystallized products is about two orders of magnitude higher, it is obvious that grain boundary strengthening occurs. Preliminary results8 have indicated that the flow stress containing no grain boundaries, A is a constant and t is the subgrain size. At elevated temperatures the effect of boundaries is more complex; it has been shown11 that recrystallized products having an oxide content of about 3 wt pct are more creep resistant than extruded material in the temperature range 400° to 600°C, whereas on application of a higher strain rate the tensile flow stress (0.2 pct offset) is higher in extruded than in recrystallized aluminum—5 wt pct aluminum oxide products at temperatures from room temperature to 427°C (800), Finally it has been shown12 that the Brinell hardness at 350°C of extruded products having about the same content of aluminum oxide increases with decreasing grain size, determined by X-ray line-width measurements. The present study was undertaken to obtain a quantitative relationship between the tensile strength and the grain size of aluminum aluminum-oxide products in the recrystallized as well as in the extruded state. The tensile testing was performed at room temperature and at 400uC. The grain size of the recrystallized products was varied by changing the degree of cold-work preceding the recrystallization heat treatment. In extruded products grain (or subgrain) size variations were obtained by high-temperature heat treatment after extrusion. EXPERIMENTAL a) Materials. Aluminum aluminum-oxide products have been manufactured by consolidation of aluminum powder covered with a layer of aluminum oxide formed during powder manufacturing. The products examined were manufactured from atomized powder containing

Jan 1, 1970

By F. Wald, A. J. Rosenberg

The general features of the constitution of the B-Pt system were determined using standard rnetal-lograph~c, thermoanalytic, and X-ray diffraction techniques. Three compound were found. Two of these, Pt3B and Pt,B, are formed by peritectic reactions at 523° and 890°C, respectively. The third, Pt3B,, is congruently melting with a flat maximum at 940°C but decomposes eutectoidally in to Pt,B ant1 boron nt - 600° to 650°C. THE low-temperature allomorph of boron (red, simple rhombohedra1 a boron) is of scientific and technological interest as an elemental semiconductor.' However, the studies of this material have been hampered by its reported instability above 1200"~ which precludes crystal growth from the melt (mp - 2200°C). Crystallization from platinum solutions has been suggested as an alternative crystal-growth technique, but has met with only limited success.' The technique depends upon the existence of a significant difference between the eutectic temperature and the transformation temperature of boron. In order to clarify the conditions for further crystal-growth experiments, we found it desirable to redetermine the main features of the B-Pt phase diagram since previous reports on the system1'5'6'7 are in marked disagreement. EXPERIMENTAL The experimental methods used were thermal analysis, metallography, X-ray analysis, and, to a lesser extent, measurements of microhardness. Most of the alloys were prepared from spectrograph-ically standardized boron obtained from Johnson-Matthey &Co., Ltd. (212 ppm impurities, exclusive of carbon and oxygen) and platinum powder obtained from F. Bishop & Co. (200 ppm impurities, mainly of other platinum group metals). Some alloys were also prepared with very high-purity, float-zone refined boron (99.9999 pct obtained from "Wacker Chemie" and extrahigh-purity platinum (99.999 pct) obtained from Johnson-Matthey & Co., Ltd. The reported results did not depend on the choices of these starting materials. Five-gram alloy specimens containing 10, 20, 25, 27.5, 30, 33.3, 34, 35, 37, 37.5, 38, 39, 40, 41, 42, 43, 45, 50, 55, 60, 70, and 80 at. pct B were made by melting the elements together in boron nitride crucibles using rf heating of a graphite susceptor, either in vacuum or under high-purity argon. All alloys were heated to at least 1800°C for -5 to 15 min. Most of the alloys did not wet the crucibles when the latter were outgassed by preheating under vacuum. In any event, no weight loss was detected after melting, and the nominal composition was assumed for all specimens. Thermal analysis on 2.5-g samples were carried out in boron-nitride crucibles under a vacuum of 5 x X torr. The apparatus was heated in a "Kan-thal A 1" wound furnace, which limited the maximum temperature to about 1100°C. The output of the indicator thermocouple was fed to a dc recorder with a 1-mv full-scale span and an adjustable zero. The apparatus was calibrated repeatedly, using the freezing points of high-purity aluminum, silver, and gold. The results justified the use of the NBS voltage vs temperature tables for Pt/Pt 10 pct Rh thermocouples. All thermal analyses were run at least twice and both the heating and cooling effects were recorded. Most of the alloys had a very strong tendency to supercool. However, the use of mechanical vibration permitted reproducibility within *5°C for all alloys, except in the region around 40 at. pct B. Only the cooling effects are plotted in Fig. 2, since they appear to be more reliable. For metallography, the alloys were cut with a diamond cutting wheel, cast in a polymethacrylate resin, ground and polished with diamond paste, and etched with dilute aqua regia, a common etch for platinum alloys. Both copper and molybdenum radiation were employed to obtain X-ray diffraction data using Debye-Scherrer cameras and a "Norelco" diffractometer Diffractometry with high scanning speeds (1 deg per min) using nickel filtered CuK, radiation was used to identify the main regions of the diagram. However, molybdenum radiation was used for the detection of boron, since the latter showed very strong absorption and fluorescence effects with CuK, radiation. RESULTS AND DISCUSSION Three intermediate compounds, corresponding to the compositions Pt3B, Pt2B, and Pt3B2, were found in the system. Fig. 1 reproduces their X-ray diffraction spectra, together with those of pure boron and pure platinum. As can be seen from the thermal-analysis data in Fig. 2, Pt3B and Pt2B are formed by

Jan 1, 1965

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.' The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963

By L. D. Jaffe, D. C. Buffum

EARLIER the authors and coworkers had pre sented data on isothermal temper embrittlement of an SAE 3140 steel?' In that work, however, attention was concentrated on embrittlement at 575°C and below. Preliminary measurements showed that embrittlement at 675 °C was much mote rapid than would be expected from the data at the lower temperatures: and indicated the need for further work above 575°C. The possibility of an upper nose in the time-temperature embrittlement diagram above 575°C was pointed out. Procedure The same heat of SAE 3140 steel was used as in the previous work, and experimental methods were the same. All blanks were austenitized 1 hr at 900°C and water, quenched. Groups were then tempered 1 hr at 675"C, water quenched, and given embrittling treatments for times of 5 min to 240 hr at 675" to 600 °C, as shown in Table I. Other groups, after the temper and quench, were embrittled 48 to 1440 hr at 550°C. Another series was tempered 240 hr at 675"C, quenched, and held for various times at 650" to 375°C (Table 11). For comparison, a series was tempered for these same times at 700°, 675", and 650°C (Table 111). The Ae, temperature for this heat of steel had been determined as approximately 690°C;1*a the treatments at 700°C were introduced to determine the effects of tempering in a range where a little austenite would fonn. A large number of other treatments, involving holding at two temperatures in succession after the temper, and occasionally slow cooling or heating, were also studied. These treatments are listed in the tables. Austenitizing was done in air; all subsequent treatments were in salt. Blanks were always water quenched after the last treatment. The heat-treated blanks were machined to standard V-notch Charpy specimens. A transition curve for each group was obtained by breaking the specimens at various temperatures on a 217 ft-lb impact machine having a striking velocity of 16.8 fps, and plotting the observed percentage of fibrous fracture vs the test temperature. From this plot, the transition temperature was taken as the lowest temperature at which the fracture appeared 100 pct fibrous; its accuracy is estimated as +5"C. Generally, hardness was measured on every bar. Since a decrease in hardness itself seems to decrease the transition temperature somewhat, a correctiona of —0.28"C per Bhn was applied to permit comparison of the transition temperatures on a uniform basis of 24 Rc. The transition temperature and hardness results are given in Tables I through VI. Where overlap of earlier work1.' occurred, data were combined.

Jan 1, 1958

Jan 1, 1899

By P. Chiotti, J. T. Mason

Ther?nal, X-ray, metallographic, and vapor pressure data were obtained to establish the phase diagram and standard free energy, enthalpy, and entropy of formation for the compounds in the Sw-Zn system. Four compounds, SmZn, SmZn2 , SmZn4.s, and SmZn8.5, melt congruently at 960°, 94Z°, 908°, and 940°C, respectively. The cornpounds SlnZns, Sm3Znll, and SnzZn7.3 undergo peritectic decomposition at 855", 870°, and 890C, respectively. Another compound of uncertain stoichiometry, SmZn11, undergoes peritectic decomposition at 760°C. Four entectics were observed with the following compositions in weight percent zinc and eutectic tenzperatures in degrees Centigrade: 12 pct, 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. An allotropic transformation and a composition range were observed for the SmZnz compound. The transfor)nation varies from 905" to 865°C as the zinc content increases from 16.0 to 48.5 wt pct, respectively. The free energy of formation of the compounds at 50PC varies between -15.9 kcal per mole for SmZn to -51.1 kcal per mole for SmZn,.,. Corresponding enthalpies vary between -19.2 to -78.3 kcal per mole. The ther-modynamic properties for the liquid alloys are described by the relations: A search of the literature revealed very little information on the Sm-Zn system. Chao et al.&apos; as well as Iandelli and palenzonai have reported the structure of SmZn to be cubic B2 type and Kuz&apos;ma et al3. have reported the structure of -sm2zn17 to be of the Th2Ni17 type. The purpose of this work was to establish the phase diagram of this system, to determine the zinc vapor pressure over the solid two-phase regions of the SYstem, and to calculate the thermodynamic properties of the compounds. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in this investigation were Bunker Hill slab zinc 99.99 wt pct pure and Ames Laboratory samarium. Analysis of the samarium by chemical, spectrographic, and vacuum-fusion methods gave the following average impurities in ppm: Nd, <200; Eu, <100; Gd, <100; Y, <50;Ca, 225; Ta, 400; Mg, 10; Cu, ~50; 0, 175; H, 20; and N, 15. The elements Fe, Si, Cr, Ni, Al, and W were not detected. The samarium was received as sponge metal and was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys with zinc contents up to the Sm2Znl, stoichio-metry. At higher zinc contents the grain boundaries of the tantalum containers were penetrated by the alloy and the containers failed during prolonged annealing. About 25 g of massive zinc and samarium sponge were sealed in tantalum crucibles equipped with thermocouple wells. These crucibles were in turn sealed in stainless-steel jackets. All closures were made by arc welding under an argon atmosphere. The samples were equilibrated in an oscillating furnace and in some cases were given various heat treatments in a soaking furnace. After appropriate heat treatment the steel jackets were removed and the alloy subjected to differential thermal analysis. The apparatus was calibrated against pure zinc and pure copper and found to reproduce the accepted melting points within 1°C. Alloys were subsequently subjected to metallographic examination and those of appropriate compositions were used for X-ray diffraction analysis and for zinc vapor pressure determinations. The vapor pressures were determined by the dewpoint method. Both the differential analysis and dewpoint measuring apparatuses have been described in earlier papers.4, 5 All alloy samples were etched with Nital (0.5 to 3 pct nitric acid in alcohol) except the samarium-rich alloys. These more reactive alloys were electro-polished in a 1 to 6 pct HClO4 in methanol solution at -700c at a potential of 50 v. EXPERIMENTAL RESULTS Phase Diagram. The results of thermal analysis are indicated by the points on the phase diagram, Fig. 1. Eight compounds and four eutectics were observed. The composition of the compounds and their melting or peritectic temperatures are given on the phase diagram. The four eutectic compositions in wt pct zinc and eutectic temperatures in % are: 12 pct,- 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. The stoichiometry of the most zinc-rich compound is still uncertain, but is very likely either SmZnll or SmZnlz. However, to simplify the presentation which follows it will be referred to as SmZnll. As shown on the phase diagram the phase regions for some of the samarium-rich alloys have not been unambiguously established. A sample of pure samarium was observed to transform at 924°C and to melt at 1074"C, in good agreement with corresponding val-

Jan 1, 1968

By L. W. Blau

RESEARCH work in exploration and production was further reduced during 1943 owing, partly, to difficulties in the acquisition of apparatus and, principally, to the exodus of research men to governmental agencies conducting research and to the armed forces.

Jan 1, 1944

The Library is a cooperative activity of the American Institute of Mining and Metallurgical Engineers, the American Society of Civil Engineers, the American Institute of Electrical Engineers and the American Society of Mechanical Engineers. It is administered as a public reference library of engineering and the allied sciences. It contains 133,000 volumes and pamphlets, 6700 maps and receives currently most of the important periodicals in its field. In order to place the resources of the Library at the disposal of those unable to visit it in person, the Library is prepared to furnish lists of references to engineering subjects, copies or translations of articles, and similar assistance. Charges sufficient to cover the cost of this work are made.

Jan 1, 1933

Denver, the Mile High, Queen City of the Plains, your host for AIME&apos;s 99th Annual Meeting has many exciting and picturesque places for you to visit during your stay. A host of restaurants cater to every taste; supper clubs and theaters provide nighttime entertainment; there are sports facilities and a plethora of shops for the ladies. When it comes to dining out, there are many excellent restaurants within walking distance of the Denver Hilton --among them, three in Brooks Towers: the Gitana, the Boston Half Shell serving the finest seafood, and Marvelous Mary&apos;s. In the Larimer Square area there in the Bratskellar with a true Germanic atmosphere and Sperte&apos;s Laffite offering a typical New Orleans setting.

Jan 1, 1970

By A. W. Gauger

SMELTING of iron ore, manufacture of steel, and the fabrication of ferrous metal products are all processes that require energy. Charcoal was adequate, to supply this energy for the relatively simple processes of the early iron-masters. In the fourth decade of the nineteenth century, anthracite and bituminous coal and later coke supplanted charcoal for the smelting of iron. So far as the chemical phases of the process were concerned, charcoal was an ideal iron-furnace fuel. It had practically no sulphur, and its ash, besides being low in quantity, consisted chiefly of lime and alkalies, thus supplying a part of the flux required for smelting the ore. The ash of coal and coke on the other hand, being largely silica, had itself to be fluxed with bases added to the charge. Physically, however, coke proved to have many advantages over charcoal, which could not be used in the furnaces of today. The chief reason, however, for the change from charcoal to coke was the impossibility of maintaining an adequate wood supply.

Jan 1, 1941

By A. P. Young, F. C. Holden

IN many of the early investigations of the aging of titanium alloys, it was observed that the retained beta phase could be aged to a high hardness without an apparent change in microstructure; moreover, in some alloys it was found that even a very rapid quench produced beta having an anomalously high hardness. What appeared to be hard beta phase was designated as "beta prime," to distinguish it from the softer normal retained beta phase. Frost and co-workers&apos;.&apos; demonstrated that the increased hardness is caused by the formation of a metastable phase, omega, which can be identified from its X-ray diffraction pattern. This reaction also has been studied by Brotzen, et a1.,3 and the structure of the omega phase has been published by Silcock, et al.," and by Austin and Doig.3 The X-ray diffraction analysis by Austin and Doig indicated that omega is low in alloy content, approaching the composition of the stable alpha. The aging process proceeds by the path Thus, overaging results in the formation of alpha and the ultimate disappearance of omega. This is accompanied by a decrease in hardness and a recovery of ductility. The present work represents a study of the aging process in a high-purity Ti-6.4 Mn alloy, in which optical and electron microscopy, X-ray diffraction, and hardness data were correlated. The specimens, 1/8-in. sections cut from 1/4-in.-diam rod, were heated in argon to a temperature just into the beta field (810°C), held for 1 hr, and water-quenched. The aging samples were heated in air for 1 hr at 300 to 500°C. The specimens were ground and mechanically polished, finishing with alternate etching and polishing on a slow-speed wheel to remove disturbed metal from the surface. The surface finally was swab-etched, rinsed with tap water, and air-dried. The etchant used was an aqueous solution containing 1 1/2 pct HF and 3 1/2 pct HNO3. This procedure is identical with that used for preparing metallographic specimens, except that the optimum degree of final etching required for electron microscopy may vary from that used for light microscopy. Metal replicas, backed with silica, were prepared from plastic strip-pings for examination with the electron microscope. Complete details of the procedures used for preparing these replicas are available elsewhere." Fig. 1 shows a comparison between the structures revealed by the electron microscope and those obtained by conventional light microscopy. Hardness and X-ray diffraction data are listed in Table I. No evidence of a second phase is apparent in the optical micrographs for the as-quenched sample, or for the specimens aged at 300 or 400°C; fine alpha particles can be seen in the specimen aged at 500°C. In the electron micrographs, visible equiaxed pocks appear in the as-quenched specimen, and, with increasing density, in the samples aged at 300 and 400°C. After aging at 500°C, the structure becomes markedly coarser and develops an oriented appearance of a second phase, coincident with the appearance of visible alpha particles in the light micrographs. These observations are confirmed by X-ray diffraction and hardness data. In these specimens, aged for 1 hr, the intensity of the omega pattern increases to a maximum at the 400°C aging temperature, corresponding to maximum hardness and the maximum density of pocks in the electron micrographs. At this point the beta phase shows a definite enrichment in Mn. At 500°C, little or no omega re-

Jan 1, 1959

By S. T. Wlodek

The surface and subscale oxidation reactions were followed by means of continuous weight-gain and metallographic techniques over the range 1600" to 2200°F (871° to 1204 °C) for up to 400 hr. Full identification of all scale and subscale reaction products was obtained by electron and X-ray diffraction. At or below 1800°F (982°C) a linear rate of reaction (QL = 46.0 kcal per mole) governed the oxidation process, extending for up to 100 hr at 1600°F (871 "C). During linear oxidation the surface scale consisted of an amorphous SiO2 film overgrown with Cr 2O 3 and NiCr204. This initial linear process was followed, and above 1800°F completely replaced, by two successive parabolic rate laws (Qp = 60 and 57 kcal per mole). This parabolic reaction involved the formation of a complex scale consisting of Cr2 O3 and smaller amounts of NiCr2O4. Parabolic oxidation appeared to coincide with the disruplion of the silica film present during linear oxidation and was followed by subscale (internal) oxidation of crystobalite and NiCr2O4. The balance between the subscale and surface oxidation reactions controls the oxidation of this commercial alloy. The amorphous silica film appears to result in the linear rate and diffusion through Cr2O3 is the more likely rate-limiting step during parabolic oxidation. THE oxidation of a multicomponent composition is a complex phenomenon not presently amenable to a rigorous classical interpretation. Nevertheless, even a qualitative understanding of the scaling and subscale reactions that occur in a commercial composition can illuminate the reactions that limit its high-temperature stability in an oxidizing environment. This study of the oxidation of Hastelloy Alloy X presents the first of a series of studies with the above approach in mind. Hastelloy X exhibits one of the best combinations of strength and oxidation resistance available in a wrought, solution-strengthened, nickel-base alloy. Although during long time exposure some precipitation of M6C and M23C8 carbides as well as a complex Laves phase occurs, the amounts are probably small enough to have no appreciable effect on the chemistry of the matrix. Radavich has identified the oxidation products on Hastelloy X oxidized for 5 min to 10 hr at 1115°F as NiO and the NiCr2O4 spinel. Oxidation for 5 to 15 min at 1500°F produced a scale of spinel, NiO, and a rhombohedra1 phase, probably Cr2Os. Sannier et 2. have reported continuous weight-gain data for Hastelloy X at 1650" and 2010°F and internal-oxidation measurements after 150 hr at 2010°F. In addition, much of the data on binary Ni-Cr alloys recently reviewed by Kubaschewski and okins&apos; and Ignatov and Shamgunova4 as well as studies of binary Ni-Mo alloys5 are also pertinent to the oxidation of this composition. EXPERIMENTAL Continuous weight-gain measurements and metallographic measurements of subscale reactions were the main experimental techniques used in this study. X-ray and electron diffraction backed up by a limited amount of electron-microprobe analysis served to characterize the nature of the scale- and subscale-reaction products. Two heats of commercial sheet of the composition given in Table I and identified as A and B were used in the bulk of this study. Internal-oxidation measurements were made on a third heat of material in the form of a 0.5-in.-diam bar. In order to assure homogeneity, all heats were reannealed 4 hr at 2175°F prior to sample preparation. weight-Gain Measurement. All specimens (1.5 by 0.4 by 0.03 in.) were abraded through 600 paper, electropolished, and lightly etched in an alcohol-10 pct HCl solution. An electrolyte of 150 cu cm H,O, 500 cu cm HsPO4 (85 pct conc), and 3 g CrO3 at a current density of 0.9 amp per sq cm or a solution of 10 pct HaW4 in alcohol used at 4 v and 0.3 amp per sq cm was used for electropolishing. The resultant surface exhibited a finish of 3 ± 1 p rms. Continuous weight-gain tests were made at 1600°, 1700°, 1800°, 1900°, 2000", and 2200°F on auer&apos; type balances capable of recording a total weight change of 110 mg with an accuracy of k0.1 mg. All tests were made in air dried to a dew point of -70°F and metered into the 2-in.-diam reaction

Jan 1, 1964

By John J. Collins

[CONTENTS PAGE Purpose and scopeI Core samplingI Sludge sampling.....7 Combining core and sludge assays13 Deviation and surveying of drill holes17 Conclusions24 Acknowledgments25 Bibliography25] PURPOSE AND SCOPE The purpose of this paper is to review a few of the problems involved in the interpretation of diamond-drill core and sludge samples, with the hope that it will stimulate discussion and bring forth some of the information on the subject that has been accumulated by various organizations. The release of these data would benefit the mining industry as a whole. Particularly valuable would be the details of drilling programs that have been tested by actual mining operations, as most of the available published material is unsupported by production records. The scope of this paper is limited to a few of the commonest problems of interpreting diamond-drill core and sludge samples and the deviation of holes. It does not include the description of routine operations performed by the drillers, nor the estimation of ore reserves. The methods of calculating reserves have been described 25,26,31,32.50,65 but more information is needed on the results shown by actual mining operations. CORE SAMPLING The accuracy of diamond-drill-hole sampling depends in large measure on the percentage of core recovery. As a general rule, the longer the run, the poorer is the recovery. Although the longer runs allow cheaper drilling costs, the determining factor should be the percentage of recovery desired. The problem is one of balancing accuracy against costs. Holes of larger diameter may show improved recovery, except as Joralemon* points out that there are some conditions in which small holes give better core recovery than large holes. This is particularly true, he says, in rocks like shattered quartzite, where larger core tends to break in angular fragments and grind up, while the diameter of smaller core is less than the distance between joint planes and grinding is not so serious. In a large measure the length of the sample run should depend on the type of deposit. Favorable drilling may allow uniform sample runs of 5 ft., 10 ft., or perhaps 20 ft. In veins or beds of relatively narrow widths and changing characteristics, however, the ore zone may be overrun and ground in a core barrel full of waste rock. Generally it is desirable to break the sample at a change in the rock or ore. Such a change, often indicated by a color change in the sludge water, should be a signal for the driller to make a "dry" block and to pull out that run regardless of the length. Such a procedure permits the segregation of waste from ore samples so

Jan 1, 1946

By John J. Collins

Page Purpose and scope..................... 521 Core sampling......................... 521 Sludge sampling....................... 527 Combining core and sludge assays ...... 533 Deviation and surveying of drill holes. . . . 537 Conclusions........................... 544 Acknowledgments...................... 545 Bibliography.......................... 545 Purpose and Scope The purpose of this paper is to review a few of the problems involved in the interpretation of diamond-drill core and sludge samples, with the hope that it will stimulate discussion and bring forth some of the information on the subject that has been accumulated by various organizations. The release of these data would benefit the mining industry as a whole. Particularly valuable would be the details of drilling programs that have been tested by actual mining operations, as most of the available published material is unsupported by production records. The scope of this paper is limited to a few of the commonest problems of interpreting diamond-drill core and sludge samples and the deviation of holes. It does not include the description of routine operations performed by the drillers, nor the estimation of ore reserves. The methods of calculating reserves have been described,25,26,31,32,50,65 but more informa- tion is needed on the results shown by actual mining operations. Core Sampling The accuracy of diamond-drill-hole Sampling depends in large measure on the percentage of core recovery. As a general rule, the longer the run, the poorer is the recovery. Although the longer runs allow cheaper drilling costs, the determining factor should be the percentage of recovery desired. The problem is one of balancing accuracy against costs. Holes of larger diameter may show improved recovery, except as Joralemon* points out that there are some conditions in which small holes give better core recovery than large holes. This is particularly true, he says; in rocks like shattered quartzite, where larger core tends to break in angular fragments and grind up, while the diameter of smaller core is less than the distance between joint planes and grinding is not so serious. In a large measure the length of the sample run should depend on the type of deposit. Favorable drilling may allow uniform sample runs of 5 ft., 10 ft., or perhaps 20 ft. In veins or beds of relatively narrow widths and changing characteristics, however, the ore zone may be overrun and ground in a core barrel full of waste rock. Generally it is desirable to break the sample at a change in the rock or ore. Such a change; often indicated by a color change in the sludge water, should be a a for the driller to make a "dry" block and to pull out that run regardless of the length. Such a procedure permits the segregation of waste from ore samples so

Jan 1, 1946

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni, 16 per cent Cr, 35 per cent Ni, 12 per cent Cr, 60 per cent Ni, etc ) in recent years has been accompanied by continued demands by the consumer for improvement in properties The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper† The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure The creep-test laboratory constructed for the American Brake Shoe and Foundry Co is designed to permit 1000-hr tests in the temperature range of 1200° to 2200°F with a choice of applied stress extending from 50 to 50,000 lb per sq in in increments of 50 lb per sq in To simplify the calculation of weight combinations, the loading beams (Fig I) are provided with counterweights to eliminate the tare The precision of the knife-edges (10 1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle Check of the loading weights proved the maximum error to be 0 06 per cent Axial alignment is provided by crossed knife-edges in the grip seats The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U S Steel Corporation An 80 per cent Pt, 20 per cent Rh No 19 B and S gauge wire is used as the heating element The details of construction are shown in the radiograph reproduced in Fig 2 The windings are held in place on an alundum tube with alundum cement, the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F over a 4-in gauge length (Fig 3) To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By W. David Menzie

An inventory of the mineral resources of a region is a most desirable basis for planning their systematic development. In the absence of appropriate samples upon which to base a reliable estimate of this inventory, investigators have resorted to a number of indirect approaches; the unit regional value concept forms the basis for one such approach. The produced resources of a region are a function of the inventory multiplied by the degree of intensity (some fraction between zero and one) of development of the resources. A convenient means of expressing this amount is to accumulate the weight and value of resource and to prorate the totals over the area represented by the unit sampled; i.e., weight and value per unit area or tonnes/km.2 and U.S. 1967 $/km.2. When this approach is used for the U.S.A., South Africa and Rhodesia the average value of (log.) U.S. 67$/km.2 for the states of the U.S.A. and South Africa are similar ($55,176 U.S.$67/km.2 and $52,538/km.2 respectively); whereas, Rhodesia is relatively underdeveloped (10,301 U.S.67$/km.2). On the other hand if the individual commodities are used as a basis for comparison, the U.S.A. shows the greatest diversity (67 commodities out of a possible total of 75) with South Africa next (50 commodities) and Rhodesia last with only 26 commodities. Since it is known that area and value are not simply related perhaps diversity is directly related to area. Again the kinds of commodities which have contributed the greatest value to the totals differs, with fuels (petroleum, coal and natural gas) predominating in the U.S.A. totals; whereas, South Africa and Rhodesia obtain their greatest contributions from gold, diamonds (S. Africa) coal and asbestos. In each case the greatest value of resources is produced from sedimentary rocks. As a somewhat different kind of example, consider a single resource (petroleum, the most valuable in the U.S.A.) over a large area (number of sampling units) the U.S.A. by state. Furthermore, assume that the model frequency distribution of the amount of petroleum (tonnes/km.2) is log normal. Then the present production fails to match the model first because 17 states (34% out of 50) have not produced petroleum. Of the remaining 33 states, Louisiana has produced the most (15,177 tonnes/km.2) and the frequency histogram is still skew. A spatial analysis of the distribution of the amount of petroleum by state shows that the samples (i.e., states) are not random; the non-producers and producers tend to cluster. It remains to be seen if this is indeed a true representation of the incidence of petroleum or is a function of the exploration philosophy currently in vogue.

Jan 1, 1977

By L. B. Herring, Harold Decker

The area under discussion includes districts 2 and 4, so designated by the Texas Railroad Commission,‡ and comprises the following 26 counties: Bee, Brooks, Calhoun, Cameron, De Witt, Duval, Goliad, Gonzales, Hidalgo, Jackson, Jim Hogg, Jim Wells, Karnes, Kenedy, Kleburg, Lavaca, Live Oak, Nueces, Refu-gio, San Patricia, Starr, Victoria, Webb, Willacy, Wilson and Zapata. Drilling and Production The total number of wells drilled in this district during 1944 is shown in Table 5. This indicates a 41 per cent increase in all drilling over 1943. In spite of every handicap created by the war, the oil industry more than met the crisis in its drilling program in this district. Last year we thought it would be impossible to add to the total number of wells drilled in the previous yea;, but in spite of the lack of manpower and materials this large increase was shown. During 1944 this district produced 124,201,978 bbl. of oil from 11,607 producing wells, whereas in 1943 it produced 88,421,693 bbl. from 11,211 producing wells. This is an increase of 35,780,285 bbl. of oil. Some decline has been shown in the older fields arid undoubtedly the majority of wells in the district are producing at too high a rate. However, this district has been able to meet any demands made on it by the Petroleum Administration for War for increased production. Discoveries and Extensions There was a slight decline over the preceding year in the number of wildcats drilled, but the number of discoveries increased. In most instances subsequent development has not been sufficient to arrive at preliminary valuations but it appears that the over-all oil discoveries were below normal and that the gas discovcrics were relatively more important. The Canolis and Tijerina pools, Jim Wells County, and the Dan Sullivan pool, Brooks County, appear to be the outstanding oil discoveries of the year. No important oil reserve was discovered or developed in the Wilcox horizons, although considerable wildcatting was done. Important extensions were made at Agua Dulce and Stratton in Nueces and Teleberg Counties. Production was increased appreciably at Willimar, Willacy County, and Seeligson, Jim Wells County, in sands and areas which were apparently productive at the beginning of the year. Refining Most of the major work in the changing and completing of refineries was finished this past year. Some of the most modern refineries in the industry are now located in the Corpus Christi area. Gas and Condensate No new recycling projects were commenced during the year, nor were there any important additions to the old operations. No major gas reserve was developed, although several new discoveries suggest potentid possibilities.

Jan 1, 1945

By J. V. Gluck

In the present paper," as in earlier publications, V1&apos;2"1 the authors present experimentally obtained relations for the free energy of solution of oxygen in various metals as a function of temperature. The relations are linear and given in slope-intercept form. The authors give values for the "probable error" of the slope and intercept, citing Birge&apos;s method17 for obtaining these quantities. Birge discussed these methods as early as the period 1929-32.25726 In Ref. 25 the probable error is defined as "the numerical value which the true error is as likely to exceed as not", i.e., 50 pct probability. Ref. 26 is even more detailed and includes a lengthy discussion of the applicability of the Gaussian distribution to experimental data. However, the use of the "probable error" has come under some question. For example, Ezekiel&apos;~ states that "the use of the probable error tends to make the results appear rather more accurate than the standard error". Moroney28 stated (in 1951) that "the term &apos;probable error&apos; was used in former times to denote 0.67450 (50 pct confidence using the normal distribution)....the term, a poor one, is now very much obsolescent. It has been said that &apos;it is neither an error nor probable&apos; ". Bennett and Franklin in 1954" in discussing statistical confidence levels mentioned that "the customary use of the 5 and 1 pct levels is not completely a matter of chance; these levels probably represent a balance between the desire to be correct and the desire to be specific. Also in most people&apos;s minds the borderline between something that could possibly happen and something that is not likely to happen is somewhere in this region. Certainly 5 or 1 pct confidence limits are to be preferred to limits such as the &apos;probable error&apos; which has only a 50/50 chance of including the correct value." It may readily be seen that the 95 pct confidence level, which is given by 1.960 (assuming large sample size), thus corresponds to approximately three times the "probable error". Indeed, limits of one standard deviation correspond only to about 68 pct probability. Even if we triple the tolerances given by the authors in the equations of their Table 111, the deviations do not become excessive and would not detract from their excellent results. It could then be said with a high degree of confidence (95%) that the precision of the slope and intercept values is about *3-5 percent of their absolute levels rather than the 1-2 percent implied in Table 111. This is then compatible with an earlier suggestion of Gokcen~&apos; of a probable accuracy of 5 pct in dissolved oxygen measurements by the technique employed. Alternatively, the authors could have

Jan 1, 1967

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in &apos;Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in &apos;Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948