Search Documents

By A. Lawley S. Schuster

The tensile behavior of copper foils prepared from rolled bulk material has been studied over the thickness range 2 to 53 , and for a range of pain sizes. For foils of comparable grain size, having the cube texture and tested along (100), yield strength increases with decreasing foil thickness t below -26p, with a corresponding decrease in ductility. Deformation occurs in the form of localized slip clusters distributed throughout the gage section. To the extent that the tensile strength (10 to 18 kg mm-) is unaffected by foil thickness, and that the foils possess fair ductility, the stress-strain behavior resembles that of bulk material rather than that of whiskers or evaporated films of comparable dimensions. The dependence of yield strength o on foil thickness t below -26p is of the form: oy = oo + kt-1/2. Possible explanations for the stress increase are considered based on 1) the dependence of active dislocation source length on foil dimensions, 2) the locking of surface sources, or the blocking of mobile sources at the surface due to surface film. It is now well-established that filamentary whiskers of many materials show exceptionally high strength compared with bulk crystals.'-11 As the diameter of the whiskers decreases to -1, the observed fracture strength approaches, and in certain cases exceeds, the calculated shear stress for the nucleation of slip in a perfect crystal.' In general, the stress-strain curve is entirely elastic, with strains at fracture approaching 1 pct. Similarly, thin films12-24 of evaporated or electrodeposi-ted material have been shown to possess tensile strengths three to seven times that of bulk material, with total strains at fracture -1 to 2 pct. In the present study, attention has been directed to the room-temperature tensile behavior of thin foils of copper over the thickness range 2 to 53, prepared from rolled bulk material. Yield stress, ultimate tensile strength, elongation to fracture, and work-hardening behavior are measured as a function of grain size and foil thickness. Structurally such foils are superior to either evaporated or electrodeposited films, and in the recrystallized condition exhibit considerable ductility. Apart from preliminary work by Sumino and Yamamoto25 on the work-hardening behavior of rolled and recrystallized copper foils, no systematic tensile studies have been carried out on material of this form. EXPERIMENTAL PROCEDURE Tensile specimens were prepared from 99.995 pct purity rolled copper foils of thickness 2, 6, 12, 26, and 53, obtained from the Hamilton Watch Co., Lancaster, Pa. Irrespective of specimen shape, it is necessary to use tensile foils with edges free from notches or tears. To this end, any form of cutting operation was excluded, and the tensile foils prepared using a photoengraving process, the details of which are described elsewhere.26 Since tensile data are required under conditions of uni-axial stress, the specimen shape is extremely important. Ideally, the foil should be infinitely long, allowing a gradual taper from the grip area to the gage section; however, from a practical standpoint, long foils are easily damaged during testing. A modified tensile specimen was therefore selected having a parallel gage section 1.25 by 0.20 in. with a tapered shoulder section increasing to 0.5 in. at the grips, and an over-all length between grips of 4 in., Fig. 1. In practically all tests, these foils fractured within the parallel gage section. By approximating the foil contour (Fig. 1) to a hyperbola it is possible to analyze the stress distribution in the tensile foil using two-dimensional elasticity

Jan 1, 1964

By AIME AIME

ALL technical men who are planning to visit the Century of Progress Exposition in Chicago this summer-and all reports indicate that it will be worth visiting-should try to be there during Engineers' Week, beginning June 26. At that time most of the national engineering societies of the country will hold important meetings in that city. Engineers will thus have an opportunity not only to see the Fair at a time when special programs have been arranged for their benefit, but will have the opportunity to meet their professional brothers and to attend technical sessions of direct interest to them. The A.I.M.E. headquarters will be at the Stevens Hotel, and it will be to the interest of every Institute member who expects to attend the Fair at that time to secure his accommodations as promptly as possible. A request to the Chairman of the Chicago Section, A.I.M.E., or to the Secretary's office in New York, will bring a copy of the program as soon as it is available, together with any in- formation desired about hotel accommodations or other matters. The Chairman of the Chicago Section is J. R. Van Pelt, and his address is Museum of Science and Industry, 1525 East 53rd St., Chicago.

Jan 1, 1933

By M. A. Elliott

The technology of gasifying coal to produce synthesis and pipeline gas has advanced significantly in the Past 20 to 30 years. This period has seen the extensive use of oxygen in coal gasification, the development of suspension gasification processes and fluidized-bed gasifiers, the operation of various gasification processes at elevated pressures, and operation of gasifiers under slagging conditions. These developments are discussed, and their application to commercial and pilot plant gasifiers is reviewed. Typical processes for synthesis gas production are described, and operating results are compared. Pipeline or high-Btu gas may be produced from coal either by catalytic conversion of synthesis gas to methane, or by the direct reaction of coal with hydrogen (hydrogasification) to produce a methane-rich gas. Neither of these methods has been applied commercially, but developments pertaining to each of them are reviewed, and general processing schemes are discussed. The use of coal as a raw material for manufacturing gas has a long and distinguished history. In fact, the gas industry began in the early 1800's when William Murdock demonstrated that it was feasible to produce and distribute gas made by retorting coal. Coal was used exclusively for gas manufacture until the middle of the 19th centruy, when Lowe invented the carbureted water gas process. In that process, coke was one of the raw materials used, so coal was still an important factor in gas manufacture. However the availability and relatively low cost of natural gas in the United States, and its widespread distribution by long-distance pipelines in recent years, has virtually eliminated the use of coal as a raw material for gas manufacture in this country. It should not be inferred from the foregoing that the technology of coal gasification has remained static in the United States and abroad. In fact, in the past two decades many new concepts have been developed in both the science and the technology of gasification. This progress has been a result of the considerable expansion in research on the fundamental chemistry and physics of gasification reactions, and in development work on gasification processes. This expansion in effort stems in part from increased interest in the use of gas as a raw material for the synthesis of chemicals and liquid fuels, and in part from the need to develop methods for gasifying coal and other solid fossil fuels to ensure a long-range supply of energy in the form of gaseous fuel. In these uses of gas, synthesis gas, a mixture of hydrogen and carbon monoxide in various proportions, is the starting material. It may be converted catalytically to gaseous and liquid hydrocarbons and other chemicals, or to hydrogen for use in hydrogenation or reduction reactions. Since coal is our most abundant fossil fuel, it is inevitable that one day it will regain its prominence as a raw material for gas manufacture. It is of interest, therefore, to consider the present status of gasification technology, directing attention particularly to advances made in recent years. Inasmuch as many comprehensive treatises l-3 and review4-7 of gasification technology are available, no attempt will be made in the present review to cover all processes in detail. Instead, the discussion will be concerned chiefly with typical processes embodying the advances that are most likely to be generally applied. ADVANCES IN GASIFICATION TECHNOLOGY For purposes of this discussion the starting point will be the conventional processes that were used for many years for the complete gasification of coal. These were: 1) carbonization in coke ovens followed by gasification of coke with air and steam in cyclic water-gas generators, and 2) fixed-bed air-blown producers. Both of these methods have obvious deficiencies when we consider that the ideal complete gasification process would be a single-stage, continuous

Jan 1, 1961

By J. E. House, C. J. Lewis

In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-pregnant sulfuric acid leach solution is contacted with an organic extractant dispersed in kerosene; the uranium enters the organic phase and associates itself with the organic extractants. Simultaneously an-ions or cations, as the case may be, leave the organic extractant phase and enter the aqueous phase. The two phases are then allowed to separate by virtue of their immiscibility. Based on the data available, a generalized procedure for the recovery of molybdenum from the sodium carbonate scrub liquor of acid leach uranium mills using secondary and tertiary amine extractants is presented, as is another generalized procedure for the recovery of molybdenum from the bleed stream of alkaline leach uranium mill circuits. Such economic appraisal as can be made at this stage of the development is also indicated. Molybdenum occurs in most uranium ores. Whether the uranium is solubilized by the acid leach route or by the alkaline leach process, some of the molybdenum present in the ore is solubilized along with the uranium. Molybdenum in uranium mill pregant solutions may cause processing difficulties, among which may be mentioned the poisoning of resins, the precipitation of organo-molybdenum complexes, or the build-up of molybdenum in recycle streams. While the uranium milling industry has been successful in applying measures to overcome the problems arising from the presence of molybdenum in the circuits, such measures nevertheless add to the cost of producing uranium yellow cake concentrate. Table I shows the analysis of typical uranium pregnant leach solutions. Uranium recovery by solvent extraction is presently practiced only in conjunction with acid leach circuits, and it may be noted that of about 16,000 tons of uranium ore daily processed by sulfuric acid leach, more than half of this tonnage follows the solvent extraction route. Uranium mills leaching ore with sodium carbonate-sodium bicarbonate solution (the so-called alkaline leach circuit) do not use solvent extraction. In this case the uranium pregnant solution is sufficiently pure to permit the direct precipitation of uranium concentrate with subsequent recycle of the alkaline leach solution. While solvent extraction procedures may be developed which are economically attractive for the alkaline leach uranium process, this has so far not been the case. The earlier uranium mill solvent extraction circuits used organo-phosphate extraction reagents, among which di-2-ethylhexyl phosphoric acid was popular. It should be borne in mind that uranium in its sulfuric acid leach solution exists in an equilibrium involving uranium in both anion and cation forms: uo + 2S0 = [uo2(so4)2] For this reason uranium may be extracted by either cation extractors or anion extractors and this is likewise true of molybdenum. However, the organo-phosphate extractants also load ferric iron which is usually present in the uranium acid leach solution. For this reason, it is necessary to reduce this solution substantially to the ferrous state ahead of solvent extraction using organo-phosphate reagents. The amines, being anion extractors, selectively reject iron and thus render the iron reduction step unnecessary. In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-

Jan 1, 1961

A New Ingersoll-Rand Turbo Blower The Ingersoll-Rand Co. has added to its Turbo Compressors and Blowers a low-pressure machine t o handle volumes from 3,000 to 35,000 cu. ft. per minute at from 1-2 ½ lb. These are particularly adapted to such service as foundry cupola blowing, atomizing oil for oil burners, supplying blast to heating and annealing furnaces of various kinds, blowing air for water-gas generators, pneumatic conveying and ventilating. They are of the single stage, double flow type and are furnished either electric motor, steam turbine or water wheel driven.

Jan 6, 1916

Organization Place Date 1917 American Institute of Architects Philadelphia,.,; Pa. Dec. 26-29 American Society of Mechanical Engineers New York City. Dec. 26-29 American Mining Congress State Chapter Phoenix, Ariz. Dec. 26-29

Jan 11, 1917

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

THREE regional meetings are planned for this summer and fall following the spring meeting held under the auspices of the Iron and Steel Committee and the Ohio Section at Cleveland in April and in lieu of a general fall meeting of the Institute. Plans for all of them are maturing rapidly. Excellent programs and. interesting visits to points of local tech¬nical interest are already assured. THE SALT LAKE CITY MEETING This meeting will be under the auspices of the Milling Committee and the Utah Section. It will be one of the features of the joint convention held the week of August 22 to 26 with the Western Division of the American Mining Congress. The Congress will be responsible for the general arrangements and for the program on the first day. The following general committees have been appointed:

Jan 7, 1927

By Chung Yu, Wang

CHINA can he roughly divided into three metallogenetic province: North China, the Yangtze Valley, and South China. In North China the old Pre-Cambrian schists and gneisses are represented by the abundance of quartz mines in which sporadic occurrences of copper, lead, zinc, gold, and silver are sometimes found in subordinate quantities. Along the Yangtze Valley and in Central China, extending eastward as far as Shantung, are found here and there intrusions of dioritic rocks, in which occur the famous contact deposits of iron ore, besides which minor quantities of copper. lead, and zinc are also found. In South China the igneous intrunsions are of granitoid type in which, or in the vicinity of which, occur in certain regions immense deposits of antimony, tungsten, tin, and mercury. Broadly speaking. most of the famous coal mines are now situated in regions north of the Yangtze River, in which occur also the sedimentary deposits of iron in contradistinction to the contact deposits of iron along the Yangtze Valley.

Jan 1, 1943

By Robert B. Kistler, Ward C. Smith

The borate industry is one of the few sectors of the mining and mineral-processing industry which the United States still dominates. Since about 1927, the United States has supplied over half of the world's total boron and borate raw materials, and many of the chemical derivatives as well. Chiefly responsible for this record are companies producing sodium borates from two large deposits in southern California, at Boron (Kramer) and Searles Lake. The sodium borates, or products derived from borax and borax-containing brines, are the preferred borates for industry because they are soluble in water and combine readily with most other chemicals. Calcium borates (or sodium-free compounds) are required for certain end uses, but in general, nonsodium borates are used only where borax is not avail- able. During the past hundred years, the use of boron compounds throughout the world has risen from a few tons per year to the equivalent of about a million tons of B2O3. Leadership in supplying borates has shifted from country to country and from region to region during this period, generally as the result of the development of newly discovered deposits that were better in quality, more accessible, or more economically exploitable than previous sources (Table 1). Primary Products and End Uses The principal borate products offered by primary producers in the United States are listed in Table 2. In general, these products are utilized worldwide by almost all consumers, regardless of the original source of the primary borates. In the United States, the primary borates all originate in southern California. Colemanite is produced as crude or processed crude ore from the Death Valley area and is utilized by the fiber glass and ceramic industries without further treatment. Production from Searles Lake, Calif., is from brines that are processed in chemical plants where borax and other compounds are recovered and the principal borate products are produced. At Boron, Calif., the world's leading producer is mining a deposit of mineral borax and operating a chemical refinery. The mineral borax is mined together with included clay, and refined borax or "lo-mol" is one of the refinery products. The mineral and the chemical compound are identical, Na2B4O7- lOH2O. In addition to ship- ping all major refined borate products from Boron, the company ships semiprocessed ore concentrates to treatment plants elsewhere.

Jan 1, 1975

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

By C. Crussard, R. Tamhankar

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers accord-ing to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Gerhurd Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Staff Coordinator, James J. Burke THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Past-President; John Chiprnan, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman; Dennis Carney, John Chip-man, J. C. Fulton, J. H. Hollomon, H. H. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and D. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman, F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham, .Jr., Robert F. Hehemonn, R. I. Jaffee, F. E. Jaumot, Jr., Irving R. Kramer, A. J. Lena, Harold Margolin, C. J. McHorgue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alan U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B. King, F. C. Langenberg, W. 0. Philbrook, and T. 0. Winkler. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AIME members. Single copies, $4.00, single copies foreign, $5.00. The AIME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AIME New York ... Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts... Second class postage paid at New Yark, N. Y., and Ann Arbor, Mich. Volume 212, Number 6.

Jan 1, 1959

By Charles Jones

IN the winter of 1902, while occupying the position of mining and examining engineer for the Mountain Copper Co., Ltd., of Keswick, Cal., I had occasion to discuss with the General Manager, among other things, the question of the enormous waste of sulphur in smelting cupriferous, pyrite ore, and to cast about for means to utilize this waste or to render the fumes innocuous to vegetation. The decreasing rate of production of California farms, the consequent need of fertilizers, and the opportunity thus offered to utilize large quantities of sulphuric acid in the manufacture of superphosphates naturally brought the subject to the practical and commercial side of phosphates. I was informed that the company had made efforts to find phosphates in the West, without success. I advised as a start placing inquiries for phosphate deposits on the Pacific coast in the current mining ,journals. This was done, with the result that in January, 1903, from an advertisement in the Mining and Scientific Press we got track of a deposit in Rich county, Utah, through T.J . Wilson, of the Southern Pacific railroad in San Francisco. As soon as snow in the mountains would permit, in May, 1903, I undertook an examination of the property, with the result of recognizing the importance of the find, in spite of its lack of facilities for transportation at a commercial figure. On June 15, 1903, I concluded my report by saying, "This may be one of the world's deposits of phosphates." On Nov. 17, 1903, I concluded my report for the season in the following words : " I have now no hesitation in saying that I believe the Carboniferous formation so largely developed in the Wasatch mountains of Utah and the mountains of the Great Basin will prove to be one of the greatest storehouses of phosphoric acid in the world."

Jan 10, 1913

By B. H. Caudle, L. G. Loncarie

Pilot flooding is one method of evaluating a proposed secondary recovery project. However, the amount and rate of oil recovery from an unconfined pilot area is not usually the same as from an equal area in a large-scale flood. This is true because fluids are free to move across the boundary of a pilot area. The result is that some of the oil produced in a pilot flood may come from outside the designated area and some of the displaced oil may leave the pilot area completely. This paper presents the results of fluid-flow model studies on a five-spot pilot flood. Mobility ratios between 0.1 and to have been studied. The effects of changing the ratio of injection to withdrawal rates are shown. INTRODUCTION A small-scale field test, or pilot flood, is an accepted method for evaluating the applicability of a secondary recovery operation and the economic potential of that operation for a reservoir. The pilot flood is carried on in the same manner, with the same injected materials and at the same pressures as would be used were the secondary recovery program to be expanded to a larger area of the field or to the entire field. If the reservoir fluid and reservoir rock properties are the same in the pilot area as in the rest of the reservoir, the production, injection and other pertinent data associated with the pilot test will represent and measure what should be expected from a full-scale development of this secondary recovery program. There is one major exception which, unfortunately, has been overlooked by many and which has been awaiting quantitative definition. This is the sweep-out pattern the reservoir engineer must use in interpreting the pilot flood and in extrapolating it to the full-scale development. The sweep-out area in a pilot flood is not contained within the five-spot pattern. Further, there is oil flow into and/or out of the five-spot during a pilot test. Thus, production data from pilots must be interpreted with this different flow system and sweep pattern in mind. We have studied the sweep-out pattern that will exist for some conditions of operation of pilot flooding a single five-spot (four injection wells and one producer). In our study, reported here, we have assumed that the reservoir is relatively homogeneous and of uniform thickness in the pilot area. The results of this study en-able the engineer to predict the recovery, injection requirements and project life for a full-scale operation from the pilot flooding data. The effects of various injection to withdrawal-rate ratios and mobility ratios in a relatively gas-free (10 per cent pore volume or less) system are shown. Experimental Method The technique used in this study was the same as that for the X-ray shadowgraph studies of sweep-out pattern efficiencies.' The model of the pilot and surrounding area was made from a uniform packing of round-grain sand consolidated with an epoxy resin. Fig. 1 shows the relation between the model and the pilot area. Only one-eighth of the pilot area had to be represented in the model because we assumed equal injec-

By E. J. Haug, K. L. Clifford, K. L. Purdy

St. Joe Minerals Corp.'s Southeast Missouri Mining and Milling Division produces lead, zinc and copper sulfide concentrates at three of its operations. The Viburnum and Fletcher mills have been described in previous papers. The new Bushy Creek mill, dedicated in May of 1973, is an updated version of the Fletcher mill incorporating 8.5 m3 (300 cu ft) lead and zinc

Jan 2, 1979

By L. J. Health

Synthetic rock with predictable porosity and permeability has been Prepared from mixtures of sand, cement and water. Three series of mixes were investigated primarily for the relation between porosity and permeability for certain grain sizes and proportions. Synthetic rock prepared of 65 per cent large grains, 27 per cent small grains and 8 per cent Portland cement, gave measurable results ranging in porosity from 22.5 to 40 per cent and in permeability from 0.1 darcies to 6 darcies. This variation in porosity and permeability was caused by varying the amount of blending water. Drainage-cycle relative permeability characteristics of the synthetic rock were similar to those of natural reservoir rock. INTRODUCTION The fundamental behavior characteristics of fluids flowing through porous media have been described in the literature. Practical application of these flow characteristics to field conditions is too complicated except where assumptions are overly simplified. The use of dimensionally scaled models to simulate oil reservoirs has been described in the literature. 1-3 These and other papers have presented the theoretical and experimental justification for model design. Others have presented elements of model construction and their operation. In most investigations the porous media have consisted of either u ncon soli da ted sand, glass beads, broken glass or plastic-impregnated granular substances—materials in which the flow behavior is not identical to that in natural reservoir rock. The relative permeability curves for unconsoli-dated sands differ from those for consolidated sandstone. The effect of saturation history on relative permeability measurements is discussed by Geffen, et a1.4 Wyga15 has shown quite conclusively that a process of artificial cementation can be used to render un consolidated packs into synthetic sandstones having properties similar to those of natural rock. Many theoretical and experimental studies have been made in attempts to determine the structure and properties of unconsolidated sand, the most notable being by Naar and Wygal.6 Others have theorized and experimented with the fundamental characteristics of reservoir rocks. This study was conducted to determine if some general relationship could be established between the size of sand grains and the porosity and permeability in consolidated binary packs. This paper presents the results obtained by changing some of the factors which affect the porosity and permeability of synthetically prepared sandstone. In addition, drainage relative permeability curves are presented. EXPERIMENTAL PROCEDURE Mixtures of Portland cement with water and aggregate generally are designed to have certain characteristics, but essentially all are planned to be impervious to water or other liquids. Synthetic sandstone simulating oil reservoir rock, however, must be designed to have a given permeability (sometimes several darcies), a porosity which is primarily the effective porosity but quantitatively similar to natural rock, and other characteristics comparable to reservoir rock, such as wettability, pore geometry, tortuosity, etc. Unconsolidated ternary mixtures of spheres gave both a theoretically computed and an experimentally observed minimum porosity of about 25 per cent.7 By using a particle-distribution system, one-size particle packs had reproducible porosities in the reproducible range of 35 to 37 per cent.6 For model reservoir studies of the prototype system, a synthetic rock having a porosity of 25 per cent or less and a permeability of 2 darcies was required. The rock had to be uniform and competent enough to handle. Synthetic sandstone cores were prepared utilizing the technique developed by Wygal.5 Some slight variations in the procedure were incorporated. The sand was sieved through U. S. Standard sieves. A 18-20 sand denotes that the sand passed the Number

Jan 1, 1966

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe's love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd's register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

Jan 1, 1968

By L. B. Davidson

The petroleum literature contains many reports on the relative permeability properties of porous media. However, only recently have studies of relative permeability at elevated temperatures been made.1 -5 Each of these studies presents relative permeability data on water-oil systems in linear sandpacks or sandstone cores under isothermal conditions. The results of these investigations are dissimilar. Edmondsonl found that in Berea sandstone a temperature-dependent effect was present, while Shilobod,2 using the same material, found no temperature dependence after normalizing for initial water saturation. Workers at Texas A&M U.3-5 found that the ratio kw/ko was temperature dependent in an unconsolidated system. The differences in results of these studies are probably a consequence of differences in the material employed, in the experimental procedures followed, and in the properties of the porous systems used. This paper describes an experimental investigation of permeability ratio temperature dependence, conducted to clarify some of the results obtained by previous workers. Each experiment described in this paper involved the isothermal displacement of Chevron No. 15 white oil by either nitrogen, steam, or distilled water and displacement of water by nitrogen. All permeability ratios were calculated using the Welge procedure. Values of the water-oil permeability ratio were obtained over the temperature range 75OF to 540°F. Results indicate the ratio is temperature dependent at low water saturations, probably due to interfacial effects. However, as the saturation is increased, temperature dependence decreases until, above some minimum saturation, the ratio becomes insensitive to temperature. Previously published work indicates that the dependence reappears at very high water saturations, a region of the ratio curve not completely examined in the present study. It appears that water-oil permeability ratios are temperature dependent at the extremes of the ratio curve where changes in interfacial tension with temperature induce variations in residual saturations. Between the extremes, there is a region in which the permeability ratio is insensitive to temperature. The size and location of this region is probably a function of the characteristics of the porous system. Gas-oil permeability ratios calculated from nitrogen-white oil displacement experiments indicate a definite temperature dependence over the range 75OF to 500°F and over the entire gas saturation range studied. Evidence discussed in this report indicates that this dependence is a consequence of molecular slippage in the gas phase. This is an extension of the Klinkenberg effect6 to two-phase systems at high temperatures (the existence of slippage in two-phase systems at room temperature has been demonstrated7). Evidence for a similar source of temperature dependence in superheated steam-white oil experiments

Jan 1, 1970