Search Documents

Executive JVW REYNOLDS, Chairman SYDNEY H BALL E DEGOLYER WILLIAM H BASSETT SAMUEL A TAYLOR Finance GEORGE D BARRON, Chairman H A GUESS GEORGE OTIS SMITH Membership ] H CALLOW, Chairman GEORGE D BARRON WILBER JUDSON JOHN A CHURCH, JR H N SPICER Alternates LEWIS W FRANCIS LOUIS D HUNTOON F T RUBIDGE

Jan 1, 1923

By C. A. Hansen

The furnace used for experimental work is shown in Fig. 1. One fireclay sagger, or pot, was set within another and the space between the two filled with Silox heat insulation. The hearth is a cast-iron plate with an imbedded ribbon of nichrome wire; this wire heater is connected to a potential regulator, which permits a very close voltage control. A mechanically driven arm is fitted with rabble blades so arranged that a uniformly thick ore bed may be maintained indefinitely. This arm is usually driven at about one revolution per minute but its speed of rotation can be varied as desired. Compressed air is led into the furnace through a meter, and it was found necessary to preheat the air in order to secure the definitely isothermal conditions sought. With this arrangement, it is possible to maintain any desired temperature constant within about 5" C. for any desired length of time and to

Jan 1, 1921

By A. L. Holley

The members of the society are doubtless aware that the production of American Bessemer steel works is constantly increasing; that the same converters and machinery are doing more work every year. This enlarged output is due to various causes, chiefly the following: 1st. Better organization—better knowledge on the part of both managers and men, of the plant and the process; of the way to economize the more exhausting labor, and of the arrangement of the details of labor and operations so that they shall not conflict; also, more pluck—a greater willingness to take risks, or, more properly, such an intimate knowledge of the nature and capacities of the refractory linings in various stages of disrepair, and the probable be- . havior of the fluid metal at various stages of its treatment, that the precise nature of the risk may be better known, so that the works may be crowded to their full capacity. In the early practice, after getting four or five consecutive heats in a day, the men preferred to " let well enough alone," and to devote the remaining time to preparation for another turn. Now, thirty, and sometimes forty heats are regularly made during the twenty-four hours, day after day, without the frequent occurrence and without the fear of breakdowns or " messes," as the spilling of steel charges was graphically named in Sheffield. 2d. Although no new refractory materials have been developed, improved means of preparing such as we have, and of imbedding

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By D. C. Jackling

I BESPEAK your indulgence for a brief expression of the views of a patriarch in the field of mineral industry technology relative to young men's problems in that sphere of education and endeavor. Wherever hereafter I employ the terms "technical education," "engineer," "technologist," or similar expressions, these are intended to be understood as relating to the broad field of the sciences and arts applicable to the mineral industries. First, the usefulness of technical education to either the possessor of it or those to whom its services may be made available industrially depends primarily upon the quality of the education and the capabilities of the educated to put his talents to effective and constructive employment in his chosen field of applied science.

Jan 1, 1940

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available.

Jan 5, 1927

By J. W. H. Clare

An equilibrium isotherm at 550°C is given for ternary alloys rich in aluminum containing 0 to 15 wt pct Cr and 0 to 20 wt pct Mn. Phases encountered are: aluminum solid solution; stable temary compound G; and MnAl8,. In addition, a limited number of alloys were annealed at 450°C to check for differences from the 550°C isotherm. These experiments limited the composition of the G phase at 550°C and further experiments established that the G Dhase is not stable above 590 ± 1 °C. RAYNOR and Little1 established several equilibrium isotherms using aluminum-rich alloys containing up to 5 pct of the elements chromium and manganese. These isotherms showed that, in addition to an a solid solution and the two binary intermediate compounds 8 and MnAl6, a stable ternary compound ex-isted in the system. This phase was called the G phase because of its ghostly appearance in micro-sections. Little, Raynor, and Hume-Rothery2 found a similar phase in binary aluminum-manganese alloys and, as a result of their experiments, concluded that the G phase was a metastable phase existing in the aluminum-manganese system. This phase was stabilized by the addition of chromium. The constitutional work of Raynor and Little,' although showing the existence of the G phase in the aluminum-chromium-manganese system, did not establish precisely the composition limits of the phase or the temperature above which the phase became unstable and disappeared from the system. The work described in this paper was undertaken to provide this information. An examination of the previous work' showed that an isotherm at 550°C would provide the required data regarding composition in the shortest possible time, as the (a + G) phase field narrows considerably at higher temperatures. The same work showed that the G phase ceased to exist between 580° and 595°C. A more precise estimate of the transformation temperature would therefore be obtained by annealing selected alloys at successively higher temperatures beginning at 580°C. EXPERIMENTAL PROCEDURE 1) Materials Used—The experimental alloys were prepared from four master alloys containing 15.00 w pct Cr, 15.28 wt pct Cr, 19.80 wt pct Mn, and 19.38 wt pct Mn which were made from super-purity aluminum, electrolytic chromium, and electrolytic manganese. The aluminum was of 99.996 pct purity, the principal impurities being copper, iron, and silicon. The chromium and manganese were 99.9 pct pure, the principal impurities being antimony, calcium, and magnesium. 2) Preparation of the Experimental Alloys—The alloys were prepared in 20-g quantities by melting together the requisite amounts of master alloy and aluminum in an alumina-lined crucible and, after thorough stirring with an alumina rod, cast into a cold copper mold to give ingots 1/4 in. in diam and 3 in. in length.

Jan 1, 1960

By Samuel Hoyt

THE writer has long been interested in seeking an explanation of the upper heat effect in the copper-tin alloys over the a + ß range, first described in 1913. These notes are offered, not at all as the final explanation of this heat effect, but rather to indicate certain progress which has been made toward establishing what happens over this temperature interval. While working on the thermal analysis of the copper-rich kalchoids (copper-tin-zinc alloys), it was noted that those alloys containing major portions of tin and minor portions of zinc exhibited two marked heat effects, one at about 520° C. and the other at about 600° C., instead of the single effect which is generally observed in either of the two binary series. This matter was discussed with Dr. Guertler, who suggested that a heat effect at about 600° C. in the pure copper-tin alloys might be expected. This led to a more searching examination of the thermal critical points in the pure copper-tin alloys, with the result that a marked, although somewhat weak, heat effect was located at about 600°. Somewhat later, this upper heat effect was discussed with Dr. Burgess, and it was requested that the Bureau of Standards make heating and cooling curves of one of these alloys for the purpose of removing any possible doubt as to the actual presence of the heat effect. Results obtained by the Bureau are given in Plate I. In an earlier paper1 differential curves were published showing that the heat effect occurred at constant temperature over the a + ß range and increased in magnitude with the amount of a up to a point somewhat above 20 per cent. tin. No heat effect was noticed at this temperature in the eutectoid alloy. The existence of this heat effect seems to require a modification of the present copper-tin diagram in the a + ß field, and it has been the object of the work here presented to secure the evidence upon which such a change should be based.

Jan 12, 1918

New York Meets first Wednesday after first Tuesday of each month. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. WILLIAM A. POMEROY. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia FRANK A. ROSS Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A.,THOMSON.

Jan 4, 1915

One of the first all-hydraulic crawler drills in service at a US open-pit mine has significantly exceeded the penetration rates of comparable pneumatic crawler rigs, according to Atlas Copco Inc. Overall production with the hydraulic unit has been double that of pneumatic crawlers in use. The installation is at the Foote Mineral Co. surface mine at Kings Mountain, N.C., where the company is engaged in mining spodumene, a combination of lithium, aluminum, and silicates. The ore is found in pegmatite dikes, a tough and abrasive host rock with compressive strength of tip to 5800 kPa (40,000 psi).

Jan 9, 1978

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Mar. 10 to Apr. 10, 1915: Oscar Lachmund, Greenwood, B. C. Harvey B. Small, Mangaugue, Colombia. S. W. Ough, Pachuca, Mexico. M. F. Sayre, Schenectady, N. Y. B. W. Vallat, Detroit, Mich. James W. Hambleton, Parral, Mexico. Charles Mentzel, New York, N. I . Philip L. Gill, Woodmere, L. I., N. 1. M. K. Rodgers, San Francisco, Cal. John T. Fuller is President of the F. Shepherd Mining Co., operating at Rush Mountain, Ark.

Jan 5, 1915

Jan 2, 1976

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th -Reserve Engineers. BAINS, THOMAS M., Major, Engineer Officers' Reserve Corps. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22d Regiment, N. Y. N. G. BARLING, H. B., Ist Lieutenant', Engineer Officers' Reserve Corps. BIGELOW, BRAXTON. BLOOMFIELD, E. C., Lieutenant. , BORROW, F. K. BROCK, R. W., Major, 19th Reserve Battalion of Canadians. BROOKS, ALFRED H., Captain, Engineer Officers' Reserve Corps. BROWNE, DE COURCY, 1st Lieutenant, Ordnance Dept., Fortress Monroe, Va.

Jan 9, 1917

By H. K. Birnbaum

The termination of a twin lamella in the interior of a crystal requires accommodation of the strains at the tip of the twin which result from coherency of the twin and matrix. In zinc and magnesium crystals,

Jan 1, 1960

By Albert E. Wiggin

PagE I. Early History of Boston & Montana Mill at Great Falls (1891 to 1905). 210 a. Original Mill Built in 1891.........210 b. Coarser Concentration Tried...211 c. Screen Sizing of Fine Jig Feed Introduced..211 d. Installation of Finer Grinding.......211 e. Steam Stamp Tried in Place of Blake Crushers..... 211 j. Mill Increased from Three to Six Sections........ 213 g. Tonnage Increased from 300 to 450 Tons per Section... 212 h. Round Tables Replaced by Wilfley Tables....212 I1. Hancock Jig Replaces Evans Jig...212 a. Description of Hancock Jig...213 - b. Tests Made on- Hancock Jig..213 1. Treating Natural Feed..215 2. Treating Sized Feed..215 3. Treating Classified Feed .215 c. Tests Made on Evans Jig...216 III. Richards Pulsator Classifier System...218 a. Experimental Work.....218 b. Installation of System in Section No. 4,....... 220 IV. Woodbury Classifier and Jig System.............222 V. The Great Falls System................ 222 a. As Installed at Anaconda............ 224 1. Coarse Crushing and Jigging Division...... 225 2. Hancock Jig Division........... 226 3. Fine Middling Division.......... 229 4. Table Division............. 230 5. Slime Division.........230 b. Special Features of Great ails Flow sheet....... 231 1. Development of Hancock Jig Flow Sheet..... 231 2. Development of Finishing Table Flow Sheet.... 232 3. Treatment of Coarse Middling Table Products .. 232 4. Results of Test Made on 500-Ton Section at Great Falls Mill...........234 VI. Comparison of Great Falls and Evans System at Anaconda.... 236

Jan 1, 1914

The plans for the activities of the Petroleum Division for the coming year do not differ materially from those of the past several years. The fall meeting is scheduled for Oct. 12 and 13 and is to be held at Tulsa, Oklahoma. The Division, of course, will take part in the annual meeting of the Institute at New York. A fall meeting will also be held in California at approximately the same time as the meeting at Tulsa. A number of papers are to be presented at the two meetings simultaneously. The various committees are at work arranging the programs. The Division will continue to be active in its various fields of endeavor, such as stabilization, production reviews, and economics, but special stress is to be laid on the engineering and research fields. In the past the Division has served as a forum for open and frank discussion of problems confronting the engineers in the oil industry. It is hoped that it will continue to function in this capacity. Papers presenting original ideas and extending the boundaries of knowledge and understanding in the field of petroleum production will be welcomed. Members who have interesting information to contribute should not wait until called upon by one of the Committees, but should offer a paper at the earliest opportunity. The past year has seen a decided strengthening of the control over production, with prospects of even more rigid control in the future. It is essential that production programs under such control be carefully planned and it is highly desirable that petroleum engineers take an active part in the planning, to insure efficient production of oil and minimize the waste of this natural resource. At a time like this, when it is difficult to keep the production of oil within reasonable limits, it may seem unnecessary to improve the efficiency of production methods, but, as has been aptly said, the trouble is not that we have too great a reserve of oil but that we are producing tomorrow's oil today. Therefore it behooves those who are entrusted with the engineering and scientific phases of production to learn how to get the greatest yield economically possible from the present and future fields in order that we may enjoy the advantages of petroleum products for a long time to come.

Jan 1, 1934

By G. G. Marino, J. W. Mahar

This paper provides an understanding of the behavior and potential damage of homes resulting from sag-type mine subsidence. This is done with extensive research of numerous case histories in Illinois collected by the authors. The house response to subsidence-induced ground displacements are summarized and evaluated. A damage level criteria, specifically developed for residential structures, is presented based primarily on repair costs. Damage levels and the associated subsidence profile characteristics for each case history are compared.

Jan 1, 1986

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, Louis K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08 ADACHI, JINZOO 11 Shiba Park, Shiba-ku, Tokyo, Japan. '88 ADAMI, C. J., Min. Engr., St. Joseph and Doe Run Lead Companies, Bonne Terre, Mo. '12

Jan 1, 1917

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The current world production of iron oxide pigments is estimated by the author to be between 499 and 590 kt (550,000 and 650,000 st) based on 1979 data. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970) and increasing to $97 million by 1980 (Spinrad, 1980). Nomenclature With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments. Classification An important characteristic of a pigment is its color and, therefore, a logical separation can be made on this basis. A. Yellow Iron Oxide Pigments 1. Natural mineral origin a) Goethite b) Lepidocrocite c) Ochres d) Siennas e) Limonite 2. Synthetic pigments a) Goethite B. Red Iron Oxide Pigments 1. Natural mineral origin a) Hematite b) Siderite (calcined) c) Pyrites (calcined) 2. Synthetic pigments a) Hematite C. Brown Iron Oxide Pigments 1. Natural mineral origin a) Umbers b) Limonite (calcined) c) Siderite (calcined) d) Goethite (bog ore or sulfur mud) 2. Synthetic pigments a) Blends of hematite, goethite, and magnetite

Jan 1, 1983