Search Documents

By B. Fazan, O. D. Sherby, J. E. Dorn

McLean's technique was employed to determine the effect of temperature on the contribution of grain boundary shearing to the total creep strain in pure aluminum over the range of 610° to 747°K. The contribution of grain boundary shearing at the same stress was found to depend upon a temperature-compensated time, where the activation energy AH was practically identical with that for total high temperature creep. SEVERAL outstanding investigations by McLeanl-' have demonstrated that the total creep strain in polycrystalline aluminum at 473°K arises from microscopically detectable slip, subgrain tilting, and grain boundary shearing. Whereas microscopically detectable slip arises from dislocations that move out of the grains, subgrain tilting is due to entrapment of dislocations of like sign in subgrain bound-arles. Consequently, creep in polycrystalline aggregates appears to be the resultant of two mechanisms, namely, migration of dislocations and grain boundary shearing. This suggests that an appropriate law for creep should contain two additive terms ?1 = ?d + ?yb where the total creep strain, ?1, depends on the sums of the creep strains arising from motion of dislocations, ?d, and from grain boundary shearing, ?yb. But extensive investigations5 over wide ranges of alloys, grain sizes, temperatures, and stresses have shown that the total creep strain is quite accurately dependent on the single term functional relationship ?1 = f (?), s = constant where s is the stress (constant),* ? = te-?H/RT, t is the time under stress, AH is the activation energy, R is gas constant, and T is absolute temperature. Since Eq. 2 was found to be valid over those ranges where appreciable grain boundary shearing is observed, it appears probable that the activation energy for grain boundary shearing might be identical with the activation energy for migration of dislocations. Thus, under a given stress, it could be thought that where fd and fgb represent the appropriate functions for each mechanism of creep. The primary objective of this investigation was to obtain a direct check on the accuracy of this hypothesis. Experimental Procedure and Results Rolled aluminum sheet (99.987 pct Al), 0.100 in. thick, was used in this investigation. Creep specimens having a 0.25 in. wide, 3 in. long gage section were so machined that their axes were in the rolling direction. All specimens were annealed for 9 hr at 894°K before testing to produce a mean grain diameter of about 0.1 in. One face of each specimen was polished electrolytically in 10 pct HBF4. In order to permit accurate measurements of grain boundary shearing, the polished surface was lightly scribed with a ruling machine accurate to ±0.0001 in. to give a uniform grid of lines which were 0.01 in. apart. Although it was thought that surface working might modify the creep behavior in the vicinity of the scribed grid lines, this technique nonetheless was employed because such local differences in creep properties should not modify seriously the fractions of the total creep strain due to grain boundary shearing or to migration of dislocations. All creep tests were conducted under constant load with an initial stress of 250 psi. The specimen tem-

Jan 1, 1955

1. Mintek reports The folowing reports are available from Mintek, Private Bag X3015, Randburg, 2125 South Africa. They are available at R25 (plus R3,25 GST) per copy to South African addressees, and US$25 per copy (including airmail postage) to addressees elsewhere. Report M91D A mineralogical investigation of samples from the Renosterkop tin prospect near Upington, by M.J. Southwood. First issued Jul. 1983, reissued May 1989. 16 pp. Report M256D The upgrading of Mamatwan manganese ores heavy-medium separation, by P. W. Overbeek. First issued Apr. 1986, reissued May 1989. Report M299D A mineralogical investigation of samples from the Eenzaamheid cobalt-molybdenum deposit, by C.D. de Nooy. First issued Jan. 1987; reissued May 1989. Report M301D The evaluation of manganese metal powder by automatic image analysis, by E.J. Oosthuyzen. First issued Feb. 1987, reissued May 1989. 13 pp. Report M311D Mineralogical and beneficiation studies of ore from Lutzputz, by R.N. Guest and C.T. Logan. First issued Mar. 1987, reissued May 1989. 13 pp. Report M314D The beneficiation of a sample of magnesium ca/crete, by L. Jonker. First issued Apr. 1987, reissued May 1989. 13pp. Report M369 The determination, by flow-injection analysis, of thiocyanate, by E.A. Jones and M-J. Hennings. Jun. 1989. 7pp. Report M389 A spectrophotometric method for the determination of zinc by flow-injection analysis, by D.E. Barnes and RA. Jones. Jul. 1989. 15 pp.2. Recent publications Pumps-principles and practice. Available from K. Myles & Associates CC, P .0. Box 2212, Northclif 2115. :200pp. R99 including GST. Standard handbook of hazardous waste treatment and disposal, edited by H.M. Freeman. Bergano Book Co., P .0. Box 190, Fairfield, CT 06430, USA. 1120 pp. US$130.Quality control handbook, by J. Juran and F. Gryna Jr. Bergano Book Co. (address as above). 4th 00. 1536pp. US$125.Refractories in the manufacture and transport of pig iron. Verlag Schmid GMBH, P.O. Box 6609, 7800 Freiburg, West Germany. DM 100. The user-computer interface in process control, byW.E. Gilmore, D.I. Gertman, and H.S. Blackman. London, Harcourt Brace Jovanovich Ltd, 1989. " 312pp. $29.Aluminum alloys-contemporary research and applications, edited by A.K. Vasudevan and R.D. Doherty. London, Harcourt Brace Jovanovich Ltd, 1989. " 676 pp. " £90.3. TMS publications issued recently The folowing publications are available from The Minerals, Metals & Materials Society, 420 Commonwealth Drive, Warendale, PA 15086, USA (Telephone: (412) 776-9000, Telex: 9103809397, Fax: 4127763770). Advances in magnesium alloys and composites, by H. Paris and W.H. Hunt (eds.). 145 pp. $65. Arsenic metallurgy-fundamentals and applications, by R. Reddy (ed.). 515 pp. $104. Casting of near net shape products, by Y. Sahai (ed.). 7oopp. $155.Continuous casting of non-ferous metals and alloys, by H.D. Merchant, D.E. Tyler, and E.H. Chia (eds.). 360 pp. $90.Dislocations and interfaces in semiconductors, by K. Rajan, D. Ast, and J. Narayan (eds.). 210pp. $75.

Jan 1, 1989

By W. K. Hardy, H. H. Stadelmaier, L. J. Huetter

The ternary system Co-Sn-C was studied in the cobalt-rich region. The liquidus projection ulas established and two fonr -phase reactions were found. An isothermal section at 950°C was worked out. In the region studied the following phases were observed: cobalt-rich solid solution, graphite, binary compound y -cobalt-tin, and a ternary compound. As a result of the limited solubility of carbon in liquid cobalt-tin alloys, the investigation was limited to the cobalt-rich region. Tin contents up to 32 at. pct were studied. Cobalt of 99.99 pct purity, tin of 99.97 pct purity and synthetic graphite of 99.93 pct minimum purity prepare the alloys. Carbon determinations of all alloys were obtained by gas volumetric analysis. Samples were investigated microscopically and by X-ray diffraction using CoK, and FeK, radiation. Cooling curves were obtained with a number of alloys to determine the temperature of the four-phase reactions. The thermocouple was calibrated with the melting points of high-purity silver and copper. In the region studied the following phases were observed: Cobalt-rich solid solution (face-centered cubic) Graphite. Binary compound y (solidifies congruently at composition Cop~n)'. Ternary compound k which is face-centered cubic with superlattice and nonferromagnetic.' In Fig. 1 the fields representing the projections of the liquidus surfaces were determined by microscopic investigation and are labled by their primary phase. In the field labled C graphite is the primary phase. During solidification in this field much of the primary graphite was expelled through the surface of the melt. It could not always be established microscopically whether the remaining graphite was primary or purely eutectic. Therefore it was not possible to determine accurately the boundary curve which drops from the binary eutectic el at 1309 "~~ to the point of the four-phase reaction at F. The ter-nary carbide is the primary phase in the field labled k. To the right of this field the primary graphite is consistently nodular whereas flake graphite is observed at tin contents somewhat below F. The ternary carbide does not appear to solidify congruently. The graphite is attacked in a peritectic reaction along the boundary between k and C. Thus no graphite is observed in alloys in the k field. In alloys right of the boundary between k and C the graphite nodules are located in the center of the k crystallites, further documenting the peritectic nature of the reaction with the graphite. A four-phase reaction was found at F and 1120 &3"C. The most likely reaction is L+ CY-Co + C — k. Below the temperature of the binary eutectic ez at 1112" a second four-phase reaction was observed at E and 1100 lt3"C. It is the ternary eutectic L — CY-Co + k + y. Figs. 2(a ) to (e) show microstructures of the ternary alloys in the as-cast condition. Fig. 2(a) shows the eutectic a-Co + C (with some primary graphite) with the carbide k in the grain boundaries. Fig. 2(b) shows primary cobalt (dark areas) and the eutectic a-Co + k which is formed along F-E.

Jan 1, 1961

By A. K. Jena, M. O. Bever

The thermodynamic behavior of dilute solutions of copper, silver, and gold in liquid tin is not explained by current solution theories.1-3 The relative partial gram-atomic enthalpies, or heats of solution, of silver, gold, and platinum in liquid lead at 623°K have been measured in the investigation reported here. Their interpretation requires a modification of the regular-solution theory although lead-rich solutions may be expected to be simpler than tin-rich solutions. The liquid metal solution calorimeter used has been described.4 At the start of a run the bath consisted of 621 g of reagent-grade lead. Several calibrating additions of lead were made during a run; a value of 3.48 kcal per g-atom5 was taken for H623°K - H273°K Two runs were made with each of the solutes silver, gold, and platinum. Annealed wire samples of 99.999+ pct purity were used. Four to six samples each weighing 0.5 to 1,0 g were added from 273°K to the bath at 623°K and the associated heat effects were measured. The samples dissolved in approximately 3 min. No serious experimental difficulties were encountered. The heat effects of the additions in a run plotted against the average atom fraction of solute before and after each addition314 were linear functions of the concentration in lead of silver, gold, and platinum, respectively. By subtracting the difference between the heat contents of a solute element at 623° and. 273°K5 from the measuredheat effects, the partial gram-atomic enthalpy relative to the solid solute was obtained. The relativ: partial gram-atomic enthalpy at infinite dilution and the concentration dependence of the partial gram-atomic enthalpies obtained from the plots of vs atomic fraction x are listed in Table I. The relative partial gram-atomic enthalpy at infinite dilution of silver in lead of 5.46 kcal per g-atom at 623°K compares with values at 723°K of 5.74' and 5.765 kcal per g-atom. These data yield a temperature coefficient of 3.0 cal per g-atom-OK. The partial gram-atomic enthalpy at infinite dilution of gold in lead at 623°K is 0.89 kcal per g-atom compared with 0.85 kcal per g-atoms (obtained by extrapolation) and 0.95 kcal per g-atom.5 By combining these values for 623°K with those for several other temperatures5" the temperature coefficient of was found to be 3.2 cal per g-atom-OK. No thermodynamic data are

Jan 1, 1968

By John K. Kennedy

ThE basic equations describing continuous zone-melting via the zone-void method were reported by Pfann. Using these equations, a theoretical study was undertaken in this laboratory on the effect of the variation of the significant parameters of the zone-void system. These parameters are the zone length, 1, the heater length, h, and the effective distribution coefficient, k. The object of this study was to determine the effect of these parameters on and (where a = Cp/Cf and ß = Cw/Cf, Cp, C,, and Cf being, respectively, the solute concentration in product, waste, and feed) so that, in future application of this technique to the ultrapurification of materials, the effect of 1 and h would be predictable regardless of the value of k. The basic assumptions made by pfannl were, for the purposes of this study, assumed to hold. For k < 1, the steady-state solute distribution in the stripping section and the shift in this distribution brought about by passage of a void is shown in Fig. 7 of Ref. 1. In this section the definition of k and ß precludes the possibility of ß assuming values less than unity when k < 1. In the course of this investigation it was found that computations based on Pfann&apos;s equations gave values of ß less than unity in the region 1 > k > l/h for almost all values of Ls, where Further computations showed that 6 assumes negative values when k > 1 for many values of L,, 1, and h. A check of the derivation of the stripping-section equations showed that an error had been

Jan 1, 1964

By R. B. Russell

SINCE Cahn&apos;s¹ paper on plastic deformation in orthorhombic (a) uranium an increasing amount of work is to be expected on orientation of single crystals and preferred orientation in this metal. It would seem desirable to have a table of angles between crystallographic planes (hkl) and (HKL). Table I shows these angles as distances from (loo), (0l0), and (00l), and in Fig. 1 as a standard (001) stereographic projection. Only the locations of poles whose diffracting planes produce Cu Ka reflections up to 0 = 70.5" (i.e. (154) ) are given." The relative reflection of these planes are represented by circle diameters. It is hoped that the projection may also be used in making inverse pole figures, originally suggested by Harris.&apos; Values of 4 were calculated from the expression hH kK 1L cos = hH/a²+kK/b²-lL/c² where the lattice parameters a, b, c, and the spac-ings d were taken from the work of Jacob and Warren." (They report a = 2.852 kX (2.8578 A), b = 5.865 kX (5.8768 A), c = 4.945 kX (4.9550 A).) The parameters reported by them may be subject to revision,4,5 accordingly the interplanar angles are listed to only the nearest tenth of a degree. References ¹R. W. Cahn: Acta Metallurgica (1953) 1, p. 49. ¹G. B. Harris: Philosophical Magazine (1952) 43, p. 113. 3C. W. Jacob and B. E. Warren: Journal ACS (1937) 59, p. 2588. 4J. S. Lukesh: Acta Crystallographica (1949) 2, p. 420. ³ J. Thewlis: Nature (1951) 168, p. 198.

Jan 1, 1954

By John H. Smith, Michael B. Bever

Pure gold was deformed by wire drawing at room temperature and 78°K. After deformation at room temperature, the stored energy and the resistivity increment reached nearly constant levels at high strains, whereas the yield stress continued to increase with strain. After deformation at 78K, the stored energy, the reszstivity increment, and the yield stress were larger than after deformation at room temperature mzd increased continuously with strain. Annealing at THE stored energy and the changes in properties resulting from cold working of Au-Ag alloys by various processes have been the subject of a series of investigations in this laboratory.&apos;-&apos; The work reported here room temperature after deformation at 78°K did not affect the yield stress appreciably. The stored energy, resistivity increment, and Lncrease in yield stress after deformation at room te-lnperature can be explained primarily in lerrns of dislocations while point defects, as well as dislocations, contribute to the changes in these properties after deformalion at 78°K. extends this research to pure gold. The stored energy, the resistivity increment, and the tensile properties after deformation by wire drawing were measured as functions of the strain at room temperature and at 78°K. The effect of the testing temperature and the effect of intermediate annealing at room temperature before testing at 78°K on the tensile properties of gold deformed at 78°K were also investigated. wire drawing made it possible to use a large range of strains, which was desirable because previous work on the deformation of gold had been carried out mainly at relatively small strains.&apos;-l2 Also, wire specimens

Jan 1, 1969

By Hideki Yamamoto, Norihiro Murayama, Junji Shibata

"Hydrothermal syntheses of zeolite from coal fly ash were carried out by using various alkali sources. NaOH, Na2CO3, KOH, K2CO3 and their mixture were applied for an alkali source of zeolite synthesis. The various physical properties of the reaction product, such as the kind of zeolite crystal, cation exchange property, surface texture and so on, was investigated through the zeolitization reaction from fly ash. The mechanism of zeolitization reaction was considered from these results.Zeolite P(NaP), hydroxysodalite(HS) and chabazite(K-CHA) are synthesized as zeolite species, when fly ash hydrothermally reacts in various alkali solutions at 393K. The crystal structure of the products obtained in NaOH solutions for 3h changes from NaP to HS with increasing NaOH concentration. K-CHA formation in KOH solutions needs 10h of reaction time, which is longer than that of NaP or HS.Dissolution, condensation and crystallization steps exist in the zeolitization reaction from fly ash, and the particle surface of products remarkably changes in each step. The fly ash is spherical particles and the surface is smooth(Fig.1(a)). The dissolution of fly ash occurs in the heating process until 393K, and the particle surface changes like unevenness(Fig.1(b)). In case of NaP, the condensation of aluminosilicate ions takes place at 373-393K, and the amorphous aluminosilicate is deposit on the unreacted fly ash(Fig.1(c)). The crystallization of NaP already begins to occur at 393K and the surface is covered with fine zeolite crystals for 24h(Fig.1(d))."

Jan 1, 2003

Professional Divisions I-Institute of Metals Division* GEORGE K ELLIOTT, Chairman GEORGE C STONE, Vice-chairman WILLIAM M CORSE, Secretary-treasurer Executive Committee D K CRAMPTON SAMUEL L HOYT R I, SUHL W K FRANK ZAY JEFFRIES A E WHITE H W GILLETT H C JENNISON R F WOOD STANISLAUS SKOWRONSKI II-Petroleum Division F JULIUS FOHS, Chairman EDWARD L ESTABROOK, Vice-chairman C P WATSON, Secretary-treasurer

Jan 1, 1923

By S. Luszcz, R. W. Vook, Fred Witt

In situ X-ray investigations were made on polycrys-talline silver films deposited by vacuum evaporation on (111) CaF2 and (100) NaCl single-crystal substrates at 80°K. The films were evaporated and annealed in an X-ray diffractometer attachment having a residual gas pressure of 2 x lo-&apos; Torr. All measurements were made without exposing the films to the atmosphere. Measurements were made on the films in the as-deposited state and after various annealing treatments. The intrinsic stacking and twin fault densities, the magnitudes of the uniform and nonuniform strains, and the crystallite sizes were determined. In addition the textures in the films were measured qualitatively. The results obtained for the as-deposited films on single-crystal substrates are in substantial agreement with previously reported results for silver films deposited on glass. Intrinsic stacking and twin faults, as well as uniform and nonuniform strains, were present in these films. During the various annealing treatments (up to 350°C) the faults and nonuniform strains annealed out. Considerable grain growth and texture changes occurred also. The effects were much greater for the NaCl substrate than for the CaFz substrate. The relative magnitudes of the grain growth in the variously oriented grains could be explained qualitatively in terms of the thermal strains and strain energies introduced into the differently oriented grains during the initial, irreversible anneal. These strains were due to the different thermal expansion coefficients of the film and substrate. X-RAY diffraction measurements on evaporated films deposited on substrates at low temperature have the advantage that many of the imperfections introduced into the film during deposition are "frozen in". Thus, the influence of a very important experimental variable, substrate temperature, on the imperfection structure of evaporated metal films may be studied. Moreover, the effects of annealing such films makes possible the study of thermally activated recovery processes in these films. The present study was designed to determine the influence of single-crystal substrates on the resultant film structure relative to the previous results obtained using glass substrates.&apos; To this end great care was taken to keep the experimental variables the same in the two cases. Different experimental conditions would, of course, result in films having different physical properties. Again the initial substrate temperature was in the neighborhood of 80°K and the films were subsequently annealed to 350°C. The pure metal silver was chosen for evaporation, primarily because of its relatively low stacking fault energy and consequent high fault density in the as-deposited state. The silver films were formed by evaporation onto air-cleaved {ill} CaF, and (100) NaCl surfaces cooled to 80°K in an X-ray diffractometer attachment2 having a base residual gas pressure of 2 X l0-&apos; Torr. The films were not exposed to the atmosphere until all of the X-ray data had been recorded. In this way one of the most important experimental variables, environment, could be well-controlled and reproduced. X-ray measurements were made at the temperature of deposition and included determinations of the diffraction line peak positions, line shapes, and integrated intensities. The peak position measurements were used to determine the intrinsic stacking fault densities and the average uniform strain in the film. The shapes of the diffraction lines provided information on the twin fault density, true crystallite size, and average nonuniform strain. The preferred orientation in the film was determined qualitatively from the integrated intensities. I) EXPERIMENTAL PROCEDURE The evaporator attachmentZ was charged with 99.999 pct Ag pellets positioned in a tantalum filament which had been outgassed previously at l0-8 Torr. The CaFz and NaCl single crystals were cleaved in air and then placed in position in the chamber so that their cleavage surfaces were on the diffractometer axis. The chamber was prepumped using a sorption pump, sealed off, and then baked at 150°C for 24 hr. The ion pump operated during the bakeout cycle. The substrate was then heated to 500° C by means of an auxiliary heater and kept hot until the rest of the chamber was cooled slowly to room temperature. This bakeout procedure consistently resulted in an ultimate pressure in the low lo-&apos; Torr range. The substrate was then cooled down on 80°K. Its temperature was monitored by a thermocouple wedged into the rear of the copper substrate holder. The diffracted intensity and peak position of the 111, 222, and 333 CaF, lines were measured prior to evaporation. Nickel-filtered, pulse-height-discriminated copper radiation was used. Similar measurements were made for the 200 and 400 lines from NaC1. These measurements were used as a lattice parameter check and to determine the thickness of the evaporated silver films from the attenuation of the substrate lines. The evaporation rates were approximately 3A per sec for both films while the maximum pressures during evaporation were 3 x lo- &apos; and 7 x 10"8 Torr for the CaF, and NaCl cases, respectively. The film thickness was measured by the attenuation of the CaF, and NaCl substrate lines and by at optical interference method. Values of 1700 and 1500A, respectively, were obtained for the silver

Jan 1, 1969

By M. Deighton, R. N. Parkins

The metals Cd, ,Wg-, Sn, TI, Zn, and Zr reach a peak hardness after a criticfir1 deformation by rolling- and then soften with fwther rolling-, thereby exhibiting wovk softening. Optical metallography on Cd, Mg, and Zn shows that work softening is accompanied by a change in grain size occurring during deformation. The creep of zinc from -1l° to +60°C at stresses in the range of 7.9 to 17.3 kg per sq mm is given by € = e0 -t- Bt + Kt +at6. The third and second rate constcints are related by the equation a = K~ K6 and their stress and temperature dependence can be represented by the equations K = A, . exp - (u, - Bu)/kT. A model based upon the stress activated glide of sub-boundaries is proposed which qualitatively accounts for the metallog-raphic observations. Expressions, which are in reasonable quantitative agreement with the ex-pe~inzental observations, are derived for the creep of zinc. THE term "work softening" has been used previously by Polakowski1 and by Cottrell and stokes2 to describe phenomena where further strain of a deformed material leads to a decrease in flow stress. In both cases, however, the conditions were changed for the second straining. Here, the term "work softening" is intended to refer to a decrease in flow stress after continued straining in the same direction at the same temperature: work softening is the antithesis of "work hardening". Work softening of zinc was reported by chadwick3 and in discussion of that paper Jenkins4 indicated that cadmium also work softens. More recently work softening has been reported5 in two magnesium alloys, -99.5 pct Mg. Chadwick found that the hardness, 0.2 pct Proof Stress and the UTS of electrolytic zinc all increased with progressive cold reductions up to 30 pct and then progressively decreased with further rolling. Gay and Kelly6 used a back-reflection X-ray technique to study the effect of cold rolling zinc and found that although deformations greater than 2 to 5 pct reduction in thickness produced some recrystallized grains, deformations greater than 40 pct caused com-plete spontaneous recrystallization. At deformations greater than 60 pct the material was found to consist solely of recrystallized grains, -20 pm diam, the size of which decreased with increasing reduction and was much less than the initial grain size of the annealed material (-300 pm diam). Similar results were also reported for cadmium, tin, and lead.6 Gay, Hirsch, and Kelly&apos; suggest that these experiments indicate recrys-tallization takes place when the dislocation density exceeds a certain value. However, no measurements of MATERIALS AND EXPERIMENTAL PROCEDURE The purity of the metals used in this work is indicated by the following figures: Zn (99.99); Cd (99.94); Mg (99.95); T1 (99.99). The zirconium was iodide crys tal bar with a probable purity of about 98 pct. The metals were obtained in the form of 0.25 in. thick strip or 0.425 in. diam rod by various fabrication methods and then annealed to ensure complete re-crystallization. Hardness-deformation curves were obtained at room temperature by rolling 4 in. thick strip under conditions which left a surface adequate for diamond pyramid hardness tests immediately after rolling. The hardness was taken as the niean of five impressions made using a 5 kg load and the time elapsing between rolling and making the last impression never exceeded 5 min. The zinc specimens for creep testing were from 3 by 3 by 4 in. cast slabs which were rolled to 0.10 in. thickness starting at 350°C and finishing cold. The resulting strip was cut into pieces 1 in. wide and annealed in batches. With suitable choices of annealing temperature between 100" arid 400°C five different grain sizes varying from 4.54 x 10&apos; to 3.03 x l05 grains per sq cm (530 to 20 um diam) were obtained. Creep tests were done in compression using a sub-press, based on a design after Ford,8 in which the strip is compressed between dies 0.100 in. wide under conditions of plane strain. Since there is no lateral spread of the material, the area of contact between the dies and strip remains constant throughout the test and the application of a constant load, using the load maintaining device of a hydraulic testing machine, resulted in a constant stress. Covering the dies with strips of P.T.F.E. reduced frictional effects to a minimum. The creep strain was obtained by measuring the travel of the crosshead of the testing machine to a sensitivity of 0.1 pct reduction in thickness. The complete subpress assembly was contained in a steel box and for tests above the ambient this was filled with liquid paraffin and heated electrically. Temperatures below the ambient were obtained with a cooling mixture of acetone and solid carbon dioxide in the box. The liquids were stirred and the temperature of the specimen, which was controlled to ±0.5"C dur-ing a test, was measured by a thermocouple placed near the dies. Compression testing of cylindrical specimens was also carried out in the subpress using hardened flat discs separated from the test material by P.T.F.E. sheets which obviated barrelling of the specimens. Various initial strain rates were supplied by the hydraulic testing machine, and the deformation was measured by a clock dial gage resting on the cross-

Jan 1, 1970

By William Conger, Greg Schick

Grinding media consumption is a major cost variable in industrial mineral comminution circuits. Specifically, industrial SAG media consumption results from a combination of surface abrasion wear, media breakage, surface spalling and rejection size from the mill. Three main consumption rates; weight of media consumed per time, per kWh and per weight of ore ground are defined and compared. Recent industrial data has provided an opportunity to relate consumption in terms of weight of media consumed to weight of ore ground (g/tonne) and weight of media consumed per kWh of energy consumed (g/kWh) with SAG specific grinding energy consumed (kWh/tonne). Using relationships developed from this data it is possible to project SAG media consumption in future mineral comminution circuits.

Jan 1, 2014

By Joan C. Biordi

[Composition profiles for atomic, radical, and stable species, as well as temperature and area expansion ratio profiles, have been determined for a nearly stoichiometric CH4-02-Ar flame and one to which 0.3 percent CF5Br inhibitor had been added. Net reaction rate profiles were calculated for all the observed species. For the normal flame, these and the mole fraction profiles gave rate coefficient information about the elementary reactions in the methane flame, for example, CH. + 0 4- H2CO 0 H, k4 = 1.05 X 1014CM3 mole-1sec-1 for 1,550§T 0,725&apos; K; CO + OH 4 C02 + H, k6= 4.7 X 1011 for 1,350{T X1,750° K. Comparison between the inhibited and normal flame showed that A] and [CH3] were significantly reduced at the lower temperatures in the inhibited flame even though in the hot gas region the [E] [OH!, and [0] were essentially the same in both flames. The CF3Br disappears very early in the flame, relative to the fuel, and the reaction primarily responsible for its disappearance is H v CF3Br 4 HBr + CF3, where k7 is found to be 2.2 X 1014 exp(-9460/RT) for 700-1,550° K. Reaction of the inhibitor with methyl radicals provides for the relatively small amounts of CH3Br observed, but CH3 + Br2 - CHs Br + Br must also occur. The HBr formed reacts rapidly with H atoms to form H2 and Br, but the reaction is soon "balanced" in the flame as may be demonstrated by calculation of the equilibrium constant at various temperatures. The fluoro-carbon fragment produced in reaction (7) also reacts rapidly, in part with methyl radicals to give the observed elimination product CH2CF2 Later in the flame, above -1,400&apos; K, F2CO is formed from the reaction CH2CF2 + 0 P F2CO + CH2 and k., -1.5 X 1013 at 1,600° K. The rather slow decay of carbonyl fluoride is attributed to reaction with H atoms according to the sequence F2CO I H - HF + FCO and FCO + H HF + CO.]

Jan 1, 1975

By T. Markus, K. Hilpert

Discharge vessels of advanced light sources are made of translucent polycrystalline Al2O3(PCA).These tubes contain salt mixtures, which essentially consist of metal halides. The salt mixture is present as a melt at the coldest spot of the vessel under operating conditions and vaporizes partly. The temperatures of the coldest spot range between 1200 K and 1300 K, depending on the lamp performance. The maximum wall temperatures range up to 1500 K and for special purposes up to1700 K. Important constituents of the melt are alkali halides AX (A = Na, Cs, X= Br, I) and rare earth metal halides LnX3(Ln = Dy, Ho, Tm). Severe corrosion attack on the wall material is observed in the PCA discharge vessels. The aim of this work is to elucidate the corrosion mechanism. Annealing experiments under well defined temperatures were carried out in order to understand the complex chemical corrosion processes. Two different annealing vessels were used, one for experiments under isothermal conditions with a temperature of 1473 K and one for experiments with a linear temperature gradient from 1450 K to 1600 K. The vessels were filled with salt mixtures of different compositions and annealed for 1000 h. The corrosion attack was characterised by XRD, analytical electron microscopy, high temperature mass spectrometry, and chemical analysis of the salt melts. The results of our investigations show that the corrosion attack is caused by vapour species and by the salt melt. The most severe corrosion is observed in vessels filled with mixtures of alkali halides and rare earth metal halides. No corrosion of the alumina is practically observed if pure alkali halides or pure rare earth metal halides are present in the annealing vessel. Keywords: thermodynamic, corrosion, lamps, metal halide salt

Jan 1, 2004

By D. Walton

The effect of small solute additions of Cu on the activation energies for creep A1 single crystals were determined over the range from 78° to 850° K. Below 240°K and above 800°K activation energies were unchanged. Between 240°K and 400°K strain aging causes the creep rate to become vanishingly small and the flow stress was independent of the temperature. Between 500° and 50°K the activation energy was increased to 41,000 cal per mole. NUMEROUS investigationsL have shown that solid solution alloying invariably increases the flow stress. A typical example is documented in Fig. 1. Such increases in flow stress can arise from two general effects: Alloying can increase the long-range stress fields through which dislocations must move by causing appropriate clustering; modification of dislocation densities, and so forth. Alloying can also modify the short-range stress fields that determine the activation energies for thermally stimulated migration of dislocations, such as occurs in some solute atom pinning processes, and so forth. Actually both long- and short-range stress-field effects can occur simultaneously. It was the purpose of this investigation to evaluate the effect of alloying on the short-range stress fields by determining the effect of alloying on the activation energies for creep. The resulting observations also shed some light on the effect of long-range stress fields on dislocation processes. EXPERIMENTAL TECHNIQUE Single-crystal bars (6 in. long 3/8 in. wide and l/4 in. thick) of dilute solutions of Cu in A1 were seeded, so as to provide extensive single slip, with the pole of the tensile axis located in the standard stereographic projection as shown in Fig. 2. Each crystal was grown under an argon atmosphere in a graphite mold containing a large reservoir of molten alloy for the purpose of obtaining rather uniform composition of Cu along the length of the bar. The nominal compositions of the alloys which were produced from 99.99 pct Cu and high-purity A1 containing 0.001 pct Fe and 0.001 pct Si, are given in Table I. Strains, measured by linear variable transformers attached by quartz rods to a 3 in. gage section were sensitive to and the stresses were ap- plied by direct loading of the specimen. Temperatures were determined by thermocouples attached to the gage section of the specimens. Below 400°K the apparent activation energies for creep, Q, were determined by the effect of small, rapid changes in temperature of about + 10°K from T1 to T2 on the corresponding creep rates ?1 and ?2 during primary creep according to where R is the gas constant.&apos; Above 400°K, Q was evaluated from Eq. [1] for the secondary creep rate using temperature changes of about ±20K. A typical set of results is shown in Fig. 3. RESULTS AND DISCUSSION The previously obtained effect of temperature on the apparent activation energy for creep of single crystals of high-purity A12 is shown by the broken curve of Fig. 4. The datum points on the same graph illustrate the effect of dilute a solid solution alloying with Cu on the activation energy between 600" and 750°K. Each plotted point is the average of not less than five independent test values between 600° and 750°K and not less than three at other tempera-

Jan 1, 1962

By G. Thodos, R. J. Smialek

A method has been developed that permits the correlations of Mehra and Thodos8 and Dastur and thodos2 for binary systems to be used for the prediction of the vapor-liquid equilibrium constants of the light and heavy constituents, Kland Kh, of a ternary hydrocarbon mixture. Furthermore, the unique relationship observed in this study, i.e., a plot of log Ke/Ki vs log Kp/K h is linear and passes through the origin, permits the calculation of the K-value for the intermediate component. This approach has been used to establish K-values for the constituents of the three ternary hydrocarbon systems used to develop this method and has also been applied to two additional ternary hydrocarbon systems to yield an average deviation of 7.7 per cent resulting from a total of 294 points for the five ternary systems considered. INTRODUCTION The rigorous calculation of vapor-liquid equilibrium constants for systems containing two or more components is a difficult problem and becomes extremely complex at elevated pressures and for conditions approaching the critical point. Although thermodynamic relationships can be developed to account for the vapor-liquid equilibrium behavior of simple systems, their use is limited because the necessary PVT data for these systems are not generally available. To establish a method for calculating K constants directly, without any recourse to the PVT behavior of a system, Mehra and Thodos8 applied the principle of corresponding states to the vapor-liquid equilibrium constants of binary hydrocarbon systems. They developed a series of charts which made possible the prediction of K-values for all binary hydrocarbon systems not containing methane. This work has been extended by Dastur and Thodos2 to include binary hydrocarbon systems containing methane. The charts developed in these two studies cover the high-pressure region and are applicable to conditions in the vicinity of the critical point. The ability of this approach to predict vapor-liquid equilibrium constants of binary hydrocarbon systems suggests that this method may be extended to the prediction of the K-values of the components of ternary hydrocarbon systems. In this investigation, the charts developed for both the methane and non - methane binary systems,2,8 together with mixture rules developed in this study, have been used to predict the K-values of the light and heavy components of a ternary hydrocarbon system. These calculated values are then used to establish the K-value of the intermediate component through the use of a novel relationship developed in the present study. DEVELOPMENT OF METHOD FOR PREDICTING K-VALUES OF TERNARY SYSTEMS The application of the corresponding state charts developed for binary hydrocarbon systems is restricted to those systems containing two components. The extension of these correlations to three-component systems requires that the ternary system be reduced to an equivalent binary, which can be treated in a manner consistent with the corresponding state development. To establish such an approach, the vapor-liquid equilibrium constant of the light component K is first calculated by assuming that the ternary mixture consists of the light component and a pseudo-heavy component of the intermediate and heavy constituents of the original ternary. To establish the vapor-liquid equilibrium constant of the heavy component Kh, the light and intermediate constituents of the ternary are combined to form a pseudo-light component of another equivalent binary system. The calculated values Kl and Kb are then utilized to calculate the vapor-liquid equilibrium constant of the intermediate component EQUILIBRIUM CONSTANT FOR LIGHT COMPONENT K To calculate the K value of the light (most

Jan 1, 1965

By Donald F. Saunders

Means and relative standard deviations were calculated for eU, eTh, K, and their ratios for aerial gamma-ray spectral data in 29 quadrangles at 1:250,000 scale. Known or suspected uraniferous provinces were characterized by: 1) Higher eU, eTh, and K means (due to generally higher radioelement concentrations); 2) Higher relative standard deviations for eU, eU/eTh, and eU/K (reflecting the presence of local uranium enrichments); and

Jan 12, 1979

By M. G. Benz

The superconducting performmce of diffusion-processed Nb3Sn is influenced by its micro structure. High isotropic transverse current density may be achieved in this material by a process which forms a precipitate of ZrO, within the Nb3Sn. FOR an ideal type-I1 superconductor, little or no transport current can be carried in the mixed state; i.e., little or no transport current can be carried above the lower critical field H,,, where the field penetrates abruptly in the form of current vortices or fluxoids, even though full transition to the normal state does not occur until the upper critical field H,,.&apos; Fortunately, nonideal type-I1 superconductors can be readily obtained and these carry large transport currents up to the upper critical field H. Both theoretical and experimental investigations have attributed this current-carrying capability for nonideal type-I1 superconductors to pinning of the fluxoid lattice by heterogeneities in the microstructure of the superconducting material. These heterogeneities may take the form of dislocations or dislocation clusters,2"5 grain boundaries: structural imperfections introduced by phase transformations; radiation damage,8"10 or precipitates.11"15 Nb3Sn formed by diffusion processing is a type-I1 superconductor. Heterogeneities are needed for high superconducting critical currents above H,,. This paper will cover: a) what the microstructure of diffusion-processed NbSn looks like; b) what changes in the microstructure take place when the system is doped with precipitates, and c) how these changes in microstructure influence the superconducting critical currents. EXPERIMENTAL Preparation of Samples. Diffusion processing was used to form the Nb3Sn. The procedure used was as follows: a) coat the surface of a niobium tape with tin; b) heat-treat this tape at a temperature above 930°C to form a layer of Nb3Sn at the Sn-Nb interface. Such a layer of NbsSn is shown in Fig. 1 The thickness of the NbsSn layer formed was controlled by the time and temperature of the heat treatment. The same general procedure was used for preparation of both undoped samples and samples doped with a precipitate. An additional step was included in the preparation of the doped samples which consisted of internal oxidation of zirconium to form ZrOn. The details of the doping process will be reported in a later paper. Sample Testing. The Nb3Sn tape samples were soldered to a copper or brass shunt. Current and voltage leads were then attached to the sample in the usual four-probe resistance measurement configuration. The sample was cooled to 42°K. In some cases it was cooled in the presence of a high magnetic field and in other cases with the field turned off. The results were the same for both cases. The samples were oriented in a configuration with field transverse to current but could be rotated such that the angle between the field vector and the wide side of the tape sample could be changed. Measurements up to 100 kG were done in a superconducting solenoid and measurements above 100 kG in a water-cooled copper magnet at the MIT National Magnet Laboratory. Once the test field was reached, the current in the sample was increased until voltage was detected across the sample. The critical current was taken as the current at which voltage was first detected in excess of background noise. In most cases this was 1 to 2 x 10~6 v for a— in.-wide sample carrying several hundred amperes with a in. separation between voltage leads and with a 10 "-ohm shunt resistance. RESULTS AND DISCUSSION Microstructure. Examination of the microstructure of the undoped Nb3Sn shows rather large-diameter (1 to 2 columnar grains growing outward from the niobium surface toward the tin surface. As the layer is made thicker by longer diffusion times, these grains grow longer. Few new grains are started. Transmission electron microscopy shows little or no second-phase material within the bulk of the Nb3Sn layer. The microstructure of a diffusion-processed NbsSn layer changes quite drastically when the system is doped so as to form a precipitate within the NbsSn layer. Instead of large-diameter columnar grains of NbaSn forming, smaller-diameter (0.5 to 1 ) equiaxed grains of Nb3Sn decorated with the precipitate form. Fig. 2 shows a transmission electron micrograph of a Nb3Sn layer doped with zirconium oxide. This layer has been etched so that one may look between the grains

Jan 1, 1969

By J. M. Stuve

Low-temperature heat capacities of chiolite (Na5Al3F14) were determined by adiabatic calorimetry in the temperature range 5.8 to 300 K. The derived standard entropy (S°, 298.15) was 115.6 ± 0.2 cal/deg-mole. High temperature enthalpies relative to 298.15 K were obtained by precision drop calorimetry up to 1,000 K. Tables of experimental data and related thermodynamic functions are given for the temperature range of experimental observations.

Jan 1, 1980

By W. C. Knopf, G. Samsel

For several years International Minerals & Chemical Corp. has used a radiation method to assay potassium content of products from potash and feldspar beneficiation. The procedure is rapid, accurate, and inexpensive and is easily handled, if necessary, by nontechnical personnel. Data are presented to show the accuracies that may be expected if the technique is used for control of pilot plants or large- scale plants. Natural potassium is composed of three isotopes -K39, K40 and K41. Five other isotopes, artificially produced, have been detected. In natural potassium only the K40 isotope, with a half life of 1.4 x 109 years, is radioactive. Its modes of decay are beta and gamma rays, positrons, and x-rays. Only the more abundant beta rays, however, are important in radiation measurements using geiger tubes.

Jan 10, 1958