Search Documents

By Aldo Bendezú

En el Perú, el cobalto @>0.1% de concentración se da principalmente en sistemas hidrotermales, particularmente en yacimientos de tipo IOCG y en vetas altoandinas de Zn-Pb-(Ag)-Ni. El primer tipo se presenta en al menos dos segmentos del cinturón de yacimientos IOCG de la costa, entre Lima e Ica. El segundo ha sido documentado principalmente en la Cordillera Oriental, entre Huánuco y Puno. Se han identificado 29 sistemas de vetas y mantos significativos entre ambos tipos. En las vetas, estos ocupan porciones restringidas de 100-500 m de largo, 50-200 m de alto y 0.2-1.5 m de potencia, sugiriendo masas prospectivas del orden de 0.2-0.5 Mt por cada sistema.

May 10, 2023

By Patrice Baby, Stefano Salvi, al et, Jean Vallence, Galdos, Renzo

The nature of the gold-bearing fluid and the source of gold in sedimentary-hosted gold deposits of Carlin, orogenic or epithermal types is still matter of debate. Most authors point to magmatic/ metamorphic origin for the fluids, however, the properties of such fluids and their interactions with organic carbon – a common component in this type of deposits – are not sufficiently well known. Here we present a large set of novel geochemical, mineralogical and fluid-inclusion data obtained from the Algamarca Au-Ag-Cu epithermal veins, corresponding to lateral manifestation of the neighbouring sedimentary-hosted epithermal-gold deposit at Shahuindo.

May 10, 2023

By Jorge Spangenberg, Lisard Torró, Patrick Quispe, al et, Johan Ramírez

Presentamos nuevos datos de isótopos estables de carbono y oxígeno que ayudan a delimitar el origen y la evolución de los fluidos del estadio C en el depósito de Zn-Pb-Ag-In-Sn-Cu de tipo cordillerano de Ayawilca. Los datos isotópicos de rodocrosita hidrotermal indican que los fluidos mineralizantes presentaron valores promedio de 13C y 18O de -13 ‰ (VPDB) y 19 ‰ (VSMOW), respectivamente.

May 10, 2023

By Miguel Tapia, Javier Alfaro, al et, Boris Alarcón, Sergio Giglio

El Proyecto Cachorro está ubicado a 150 Km al NE de la Ciudad de Antofagasta, en la Cordillera de la Costa de la Segunda Región de Chile, donde se encuentran depósitos de cobre tipo estratoligados, IOCG, y pórfidos (Mantos Blancos, 500 Mton @ 1,0% Cu; Antucoya, 1.200 Mton @ 0,3% Cu) (Fig. 1). El descubrimiento es el resultado de campañas de exploración greenfield en áreas cubiertas efectuadas desde 2013 por AMSA en el norte de Chile. El depósito se aloja en rocas estratificadas sedimentarias y volcánicas del Paleozoico superior al Jurásico inferior e intrusivos y brechas hidrotermales del Jurásico inferior que se relacionan temporalmente con la mineralización.

May 10, 2023

By José Gutiérrez, Cosme Soto, Octavio Vargas

El presente trabajo detalla las etapas más relevantes del proceso de cambio de la Guía Industrial 7 (IG-7) a la regulación S-K1300 cuya finalidad es reportar Recursos Minerales en la Bolsa de Nueva York. Los autores desean brindar una guía sobre las situaciones y retos más importantes sucedidos durante el proceso de adaptación y auditoria para reportar recursos minerales bajo regulación S-K 1300 en la Cia. de Minas Buenaventura. También, plantear una metodología para ponderar tanto las variables que le dan soporte a la estimación de las leyes, como los ítems que brindan calidad a la información de Geología.

May 10, 2023

By Miguel Tapia, al et, Milenko Gonzalez, Sergio Giglio

El Encierro es un yacimiento de tipo pórfido Cu-Au del Mioceno superior ubicado en la zona intermedia entre las franjas de El Indio y Maricunga, en el norte de Chile. Está emplazado bajo un extenso lithocap que presenta evidencias de mineralización de tipo epitermal de alta sulfuración y que fue explorado entre 1987 y 2010 por varias empresas. En 2016, AMSA firmó un contrato de opción de compra con Barrick con el objeto de comprobar la existencia de un sistema tipo porfídico en profundidad con potencial económico. Cuatro campañas de perforación desarrolladas entre 2015 y 2020 permitieron probar que debajo del lithocap se encuentra un sistema porfídico de Cu-Au con leyes que se incrementan por debajo de la cota 3,000 m.

May 10, 2023

By Joaquín Copaja

Highly fertile magmatic conditions for porphyry copper formation, such as high water content, can be recognized in zircon trace element chemistry using proxies as the 104(Eu/Eu*)/Yb ratio. Due to their resistance to alteration and long-distance transport, zircons hosted in sedimentary sequences can be used to assess fertility over large detrital source areas. Herein we present a study based on LA-ICP-MS analyses of zircons derived from post-Oligocene sedimentary sequences cropping out across the Paleocene-Eocene Cerro Colorado district of Northern Chile. U-Pb dating on individual detrital zircons yielded ages ranging from Jurassic to Miocene, concordant with the district geology. Subsequent fertility assessment recognized several peaks in the magmatic hydration over time.

May 10, 2023

By D. F. Malan, J. A. L. Napier

A number of shallow coal or hard rock mines employ pillar mining systems as a strategy for roof failure control. In certain platinum mine layouts, pillars are designed to ‘crush’ in a stable manner as they become loaded in the panel back area. The correct sizing of pillars demands some knowledge of the pillar strength and the overall layout stress distribution. It is particularly important to understand the impact of the layout geometry on the effective regional ‘stiffness’ of the rock mass around each pillar. An important design strategy is to model relatively detailed layout configurations which include a precise representation of the local pillar layout geometry and to analyse multiple mining scenarios and extraction sequences to select optimal pillar sizes and barrier pillar spacing. Although computational solution techniques are now impressive in terms of run time efficiency, a major difficulty is often encountered in assigning suitable material properties to the pillars and in devising an effective material description of the layered rock strata overlying the mine excavations. This paper outlines an efficient numerical strategy that can be used to assess large-scale pillar layout performance while retaining the ability to modify individual pillar constitutive behaviour. The proposed method is applied to selected layouts to compare estimated average pillar stress values against values determined by detailed modelling and against observed behaviour.

May 3, 2023

By D. F. Malan, D. Ile

This study explores the use of backfill in hard rock bord-and-pillar mines to increase the pillar strength and extraction ratio at depth. The use of backfill will also minimize the requirement for tailings storage on surface and the risk of environmental damage. A literature survey indicated that backfill is extensively used in coal mines, but rarely in hard rock bord-and-pillar mines. To simulate the effect of backfill confinement on pillar strength, an extension of the limit equilibrium model is proposed. Numerical modelling of an actual platinum mine layout is used to illustrate the beneficial effect of backfill on pillar stability at greater depths. The magnitude of confinement exerted by the backfill on the pillar sidewalls is unknown, however, and this needs to be quantified using experimental backfill mining sections equipped with suitable instrumentation.

May 3, 2023

By D. F. Malan, P. M. Couto

We propose a layout design for the UG2 Reef where weak geological alteration layers are present. The collapse of the Everest platinum mine in South Africa indicated that these layers substantially weaken the pillars. The popular Hedley and Grant pillar strength formula cannot be used where these alteration layers are present. Underground investigations at Everest mine and numerical modelling of the layout were conducted using the TEXAN code and a limit equilibrium model. Simulations of a collapsed area and an intact area allowed for a preliminary calibration of the model. This was subsequently used to explore modified layouts for these ground conditions. An alternative is to compartmentalize the blocks of ore using barrier pillars. The numerical modelling predicted that the barrier pillars appear to remain stable even in the case of large-scale collapses, provided their width exceeds 25 m. Main access routes into the mine can be protected by a double row of pillars at least 15 m wide to provide a safe travelling way. As a cautionary note, these conclusions are based on the model calibration and this needs to be refined in future. Calibration of the limit equilibrium model remains a challenge owing to the large number of parameters involved.

May 3, 2023

By J. A. Maritz, D. F. Malan

Pillar strength is affected by pillar shape, but this has largely been ignored in past research studies. Bord-and-pillar layouts are typically designed using empirical strength equations developed for square pillars. Owing to the poor quality of pillar cutting, many hard-rock pillars have an irregular shape and it is not clear how this affects pillar strength. Furthermore, the strength of rectangular pillars in comparison with square pillars is also difficult to quantify. The ‘perimeter rule’ is widely adopted for rectangular pillars, but its applicability for pillars with irregular shapes has never been tested. We used numerical modelling in this study to investigate the effect of pillar shape on strength. An analytical limit equilibrium model of a square and a strip pillar also provided useful insights. For slender pillars, the strength of a long rib pillar is essentially similar to that of a square pillar. In contrast, for rib pillars with a large width to height ratio, there is a substantial increase in strength. The study found that the perimeter rule should not be used for irregularly shaped pillars. Displacement discontinuity modelling, using a limit equilibrium approach, is proposed as an alternative to determine the strength of these pillars.

May 3, 2023

By F. J. N. Bruwer, T. R. Stacey

The research described considers whether the variability in coal material strength, as derived through a series of uniaxial compressive strength (UCS) tests, could be used to indicate the variability in coal pillar strength. The aim is to be able to use a distribution of UCS tests as input into the coal pillar strength calculation. This will allow the pillar design to be expressed in terms of a probability of failure rather than as the commonly used safety factor. To achieve this, the bulk strength factor associated with commonly used pillar strength formulae was replaced with a distribution of UCS results divided by an adjustment factor. The factor was determined so as to ensure that the resulting bulk strength does not deviate from the statistically determined bulk strength published in the original formulae. This approach enabled pillar strength distributions to be obtained using industry-accepted strength formulae, subsequently allowing for a probability of failure to be calculated for a specific pillar design. Using a regional coal material strength curve as a baseline, coalfields in which the coal is stronger than the regional mean can be identified and the pillar designs optimized. This is based on the stronger coals achieving lower probabilities of failure at similar safety factors. The research has considered actual UCS data from multiple mines in the Mpumalanga coalfields of South Africa, and has proved that the variability in material strength between coalfields could allow for some optimization using the proposed approach. Based on the data used in the study, a 2.78% increase in extraction could be achieved. However, further research will be required to validate the results of the study in an underground environment.

May 3, 2023

By D. F. Malan, R. P. Els

The limit equilibrium model, used in displacement discontinuity codes, is a popular method to simulate pillar failure. This paper investigates the use of physical modelling to calibrate this model. For the experiments, an artificial pillar material was prepared and cubes were poured using the standard 100 mm × 100 mm civil engineering concrete moulds. The friction angle between the cubes and the platens of the testing machine was varied by using soap and sandpaper. Different modes of failure were observed depending on the friction angle. Of interest is that significant loadshedding was recorded for some specimens which visually remained mostly intact. This highlights the difficulty of classifying pillars as failed or intact in underground stopes where spalling is observed. The laboratory models enabled a more precise calibration of the limit equilibrium model compared to previous attempts. Guidelines to assist with calibration of the model are given in the paper. The limit equilibrium model appears to be a useful approximation of the pillar failure as it could simulate the stress-strain behaviour of the laboratory models.

May 3, 2023

By D. F. Malan, T. E. Oates

A recent experimental pillar extraction project at a UG2 bord-and-pillar mine presented a unique opportunity to compile a new pillar database. Currently, the South African hard rock bordand- pillar mines are designed using the Hedley and Grant formula with a modified K-value. This empirically derived formula was developed for uranium mines in the Elliot Lake district of Canada. The use of this formula for the design of pillars in South Africa is questionable. Very few pillar failures have nevertheless been observed and its current calibrations for the various reef types are possibly too conservative. A new UG2 pillar database of 66 pillars, of which seven are classified as failed, was compiled by the authors. This enabled a revised ‘first-order’ calibration of the K-value for the Hedley and Grant formula. The new estimated value for the UG2 is K = 75 MPa. This gives a pillar strength that is more conservative than the PlatMine formula. This work should nevertheless be considered as only a preliminary calibration as the database was small. Further work is also required to determine whether the exponents in the formula for the width and height parameters are appropriate for UG2 pillars.

May 3, 2023

By D. F. Malan, J. C. Esterhuyse

In this study we explore the use of a novel numerical modelling approach to study the effect of pillar reinforcement on pillar stability. Case studies in the literature indicate that tendons, strapping of the pillars, and shotcrete or thin spray-on liners are commonly used to reinforce pillars. No clear methodology exists to select the type of support or to design the capacity of the support required, however. This has led to ongoing collapses in some mines in spite of heavy support being used to reinforce unstable pillars. A limit equilibrium model with confinement on the edge of the pillar was used to simulate the interaction of the support with the failing pillar. The model correctly predicts that an increase in confinement will lead to a decrease in the extent of pillar failure. As the displacement discontinuity boundary element method allows for the efficient solution of largescale bord-and-pillar layouts, the effect of pillar confinement can now be studied on a mine-wide scale. Accurate calibration of the limit equilibrium model is, however, required before this method can be used for the design of effective pillar support.

May 3, 2023

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, despite its natural abundance, demand for coal exceeds its countrywide supply due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98 percent of total raw coal production in the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an environmentally friendly manner, especially in populated areas adjacent to the mining zone. This technology eliminates blast hole drilling, blasting and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks.

May 1, 2023

By Aimee A. Woolsey

Enterprise unmanned traffic management (E-UTM) is a holistic system concept evolving from technological developments in radio frequency (RF), where dynamic tracking can be added into current and emerging platforms. This is done through inexpensive RF sensors capable of real-time and cooperative, non-GPS tracking enabling digital visualization of assets, including unmanned aerial systems (UAS). The RF sensors are low in size, weight and power (SWaP), creating efficiencies in energy and material consumption while transmitting positions in real time and at long ranges. Multiple UAS and other unmanned vehicles can be visualized for risk mitigation in operations, thus enabling mine management to have better decision-making capabilities in the current and future mosaic of mine operations.

May 1, 2023

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

With the rise in global demand for pure copper, there is an urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as effective and efficient leachants for the dissolution of chalcopyrite. This work reports on different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from the Wase local government area of Plateau state, Nigeria, and assayed as 11.30 weight percent copper.

May 1, 2023

By J. van der Walt, W. Spiteri

Flyrock remains a significant threat to the health and safety of mine employees and integrity of infrastructure, as well as to the safety of the neighbouring communities and their property. This investigation was motivated by the general lack of fundamental research and mathematically quantifiable data in the literature regarding the relationship between blast design parameters and their impact on flyrock. The focus was to develop a concept that can be used to mathematically quantify the trajectory of flyrock resulting from a blast, which can be used for future research. The ultimate goal for this technique, once it has been fully developed, is to: ➤ Enable mining operations to generate a database with accurate historical flyrock measurements resulting from their blasting operations ➤ Allow research teams to conduct scientific investigations into flyrock and the impact of various blast design parameters ➤ Generate point-cloud data to visualize blasts and flyrock in a virtual reality environment for training and education purposes. This paper summarizes a conceptual technique and preliminary fieldwork that was carried out to determine the technique’s feasibility and motivate further development. The results show conclusively that a modified photogrammetric technique is capable of capturing flyrock data for further processing and analysis. The data acquisition procedure can, at this point, be used to meet the first aim of the project, namely to gather a field database of historical flyrock generation. Further development of the technique is ongoing and it is envisioned that the scientific-based technique will provide a method whereby future flyrock studies will be comparable and that assumptions will be limited.

Apr 5, 2023

By J. W. van der Merwe, A. M. Maleka, V. J. Matjeke

The 10.5–12.5% chromium, titanium-stabilized ferritic stainless steel (FSS) plates used to fabricate coal line jumbo wagons is susceptible to undesirable chromium depletion during welding with 309L electrodes. In this work, non-stabilized FSS plates were welded using 308L welding electrodes. The objective was to weld non-stabilized FSSs using gas-shielded metal arc welding without causing sensitization. The welding process was optimized by lowering the heat input. Sensitization was assessed by rigorous etching techniques and anodic polarization scans. In addition, the welds were subjected to tensile testing, and their fracture surfaces were examined for intergranular cracking. Non-stabilized FSS plates were successfully welded using gas metal arc welding.

Apr 5, 2023