Search Documents

By G. C. Lindeque

"A downward trend in tyre life on haul trucks at an open pit iron ore mine prompted an investigation into the current tyre management strategy in order to improve tyre life. ‘Best practice’ was compared to the current tyre management strategy at the mine to determine aspects that could be improved. Aspects that showed significant room for improvement included employee tyre awareness, tyre pressure maintenance, and road conditions. For each of these aspects a plausible alternative was suggested.A new tyre management strategy was formulated as a step-by-step guide on how to implement the proposed changes. Each step introduces new initiatives but at the same time builds on the previous step’s success. A sensitivity analyses was performed to determine the impact of the proposed changes, with the variables being the reduction in the percentage of premature tyre failure, and the reduction of the site wear rate.The ‘most likely’ scenario showed an increase in tyre life of 41% for the Komatsu 730 trucks and 105% for the CAT 777 trucks if the entire tyre management model is implemented. This would result in a possible annual saving related to tyre usage of R9.2 million. OverviewThe study focused on the tyre life on the main haul fleet at an open pit iron ore mine. The haul fleet consisted of 17 Komatsu 730 (180 t) haul trucks and 12 CAT 777 (90 t) haul trucks.The haulage operation consists entirely of tyre-based haul trucks. Five per cent of the total mining budget is related to tyre costs. Since 2012 there has been a steady decrease in tyre life as measured in operating hours (Figure 1) due to the high percentage of tyres that fail prematurely. In 2014 a total of 41% of all tyres failed prematurely and 61% were classified as ‘worn out’."

Jan 1, 2016

By Samuel Rigert, Marco Bettelini

"INTRODUCTION AND OBJECTIVES Long rail tunnels require in most cases powerful mechanical ventilations. Besides requirements related to normal operation and maintenance, operational safety always requires a high level of smoke management. Identifying the optimum ventilation concept is essential for achieving proper performance and safety while keeping investment and operational cost at a reasonable level. For the purpose of the present paper, long tunnels have a length of typically 20 km or more. This is related to the European classification of trains (TSI 1303/2014), where the maximum distance from the portals to a firefighting point and between firefighting points is limited to 20 km (only category B passenger rolling stock allowed) or 5 km (general case). From TSI 1303/2014 it can be concluded, that tunnels over 20 km require in any case emergency stations with complex mechanical ventilations. Based on the experience arising from a number of recent projects in the European area, including in particular Gotthard (GBT), Lötschberg, Lyon-Tourin (LTF), Brenner (BBT) and Gibraltar, safety-relevant issues related to the ventilation of long railways tunnels are reviewed in this paper. Amberg Engineering is directly involved in these challenging design tasks and can provide first-hand experience and know-how. As a particular highlight, special attention is devoted to the longest tunnel worldwide, the 57 km long Gotthard Base Tunnel, which will be commissioned in 2016. THE GOTTHARD BASE TUNNEL Overview The Gotthard Base Tunnel will be commissioned in 2016 (official inauguration on the 1st of June and beginning of regular operation on the 11th of December) and will be the worldwide longest tunnel. Its complex and powerful ventilation system is very representative for many other long tunnels and is used as reference in this paper. Therefore, a few key characteristics of the Gotthard Base Tunnel and its ventilation system will be described in some detail in this initial chapter. The Gotthard Base Tunnel (GBT) consists of two single-track tunnel tubes with connecting galleries every 312 meters. Two so-called multi-functional stations (MFS), located at roughly 1/3 and 2/3 of the tunnel length, host the key equipment for normal and for emergency operation. At these locations, double crossovers allow trains to switch from one tunnel tube to the other. An emergency station is located in each multifunctional station, allowing trains to stop in case of emergency. The general layout of the GBT is presented in Figure 1."

Jan 1, 2016

By L. A. Cornish, I. A. Mwamba, R. A. Couperthwaite

"In previous work by the authors, it was established that additions of 0.2 at.% Ru to an Fe-40 at.% Al alloy improved the corrosion and oxidation resistance of the alloy. The alloy was produced by mechanical alloying and spark plasma sintering and the work showed that nonequilibrium processing was able to significantly refine the grain size of the material. The sintered material had a higher hardness than the as-cast material and the change in grain size did not significantly affect the oxidation and corrosion. In the present research, the mechanically alloyed powder was coated onto a mild steel substrate using cold-spray coating at a gas pressure of 10 bar and a temperature of 500°C. The coatings were found to be 5–10 um thick, although thicknesses of up to 30 um were observed. The coated materials were subjected to oxidation and corrosion tests to determine the effectiveness of the coating in increasing the oxidation and corrosion resistance of mild steel. This was done to determine the effectiveness of cold-spray coating as a technique to coat these mechanically alloyed powders. IntroductionPrevious work conducted by Mintek (Couperthwaite et al., 2013, 2015) investigated the effect of precious metal additions on the structure, oxidation and corrosion properties of an Fe-40 at.% Al (Fe- Al) alloy. Initial work determined that additions of more than 0.5 at.% precious metal did not improve the oxidation and corrosion properties of the materials and in some cases even decreased the resistance to corrosion. Further work identified Pt and Ru as beneficial additions to the FeAl alloy. Four alloys were then produced by mechanical alloying and sintering (FeAl–0.2 at.% Pd, FeAl–0.2 at.% Ru, FeAl–0.5 at.% Ag, FeAl–0.5 at.% Pt). These alloys were all successfully produced by melting and casting and mechanical alloying sintering and it was found that the nonequilibrium processing greatly decreased the grain size of the materials compared to the ascast materials. It was found that the additions of Ru and Pt were still the most beneficial to the oxidation and corrosion properties, with Ru being considered the most beneficial."

Jan 1, 2016

By P. W. Conrad, C. Todd, N. West, R. Kramer

"Surface subsidence caused by both underground room-and-pillar mining operations and solution mining operations have each been studied separately, but never combined. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. PROJECT BACKGROUND FMC Minerals (FMC) has increased the production of trona from its Westvaco Mine near Green River, Wyoming, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 1,600 feet. Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed. The location from which the trona was removed and the size of the cavern created by the solution mining operations is important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found that would allow for the use of surface subsidence measurements to estimate the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find a relationship between the measured subsidence and the solution mining activities. The project attempted to model the relationship between the measured subsidence and the solution cavern using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI), to determine the program’s usefulness for locating and developing the cavern created by solution mining activities. The project also attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The data used in this study were collected over a seven year period, 2008 through 2014."

Jan 1, 2016

By R. Roufail

"Energy consumption in stirred mills has been studied, in the last couple of decades, on a macro scale. Effective operation and meeting particle size required for downstream operations used to be the main objectives behind energy utilization of stirred mills. In this paper, three energy terms are defined to assist in understanding the breakage mechanism for various types of minerals versus mill operation. The types of minerals studied had diverse physical and mechanical properties that are summarized as specific gravity, hardness and crystal structure. The minerals utilized in this study were quartz and galena. The effect of quartz and galena mix has been addressed as well as Lead-Zinc ore sample from SAG mill discharge. The energy input to the mill is function of the agitator speed, therefore three agitator speeds were evaluated, 1000, 1500 and 2000 RPM, respectively. The energy terms studied are specific energy (kWhr/ton). Effective energy is the ratio between net energy and total energy consumed by the mill. Last type of energy is the specific breakage energy, which is the net energy consumed by the mill per one-micron breakage. Results showed that specific energy and specific breakage rate are functions of mineral type, while effective energy is only function of mill input power (agitator speed).INTRODUCTIONGrinding is the largest energy consuming component of a mineral processing operation and typically consumes about 50% of the total energy used at a mining operation (Botin, 2009). Over the last two decades, stirred mills have been extensively utilized in mineral processing operations due to increased mineralogical complexity of ore bodies. Stirred mills grind particles to less than 10 µm by applying a high power intensity. The technology has been the focus of several research studies to investigate mill energy and grinding mechanisms. Becker, et. al. (2001) studied the relationship between different types of energy including input energy, specific energy, volume/mass specific energies, to stress intensity and final product particle size. Other studies such as by Kwade (1999), Kwade and Schwedes (2002), Blecher et al (1996), Partyka and Yan (2007), Stender et al (2004), focused on mill design and/or stress intensity distribution. Peukert (2004) studied the effect of mechanical properties of the grinding media and ground material on the comminution process."

Jan 1, 2016

By L. V. Kin, V. V. Lodeischikov, A. V. Byvaltsev, IRGIREDMET JSC, O. D. Khmelnitskaya, S. V. Petrov

"Irgiredmet Institute carried out the study on the development of gold recovery technology from refractory ore from a Russian deposit. The ore contained 1.1 g/t Au, 1.5% of pyrite and 2.4% of pyrrhotite. The recovery of gold achieved was 84.7% using gravity with generation of high grade recoverable gold concentrate and gravity middling. In the course of lime treatment, cyanidation of the middling followed by tailings detoxification the consumption of reagents was 13.0 kg/t CaO, 95 kg/t NaCN and 72 kg/t Ca(OCl)2 of the concentrate. This was capital intensive.In order to decrease the consumption of reagents, magnetic separation of the middling of the concentrates from gravity separation was added to this flow sheet. Pyrrotite recovered to magnetic fraction, which did not contain gold in accordance to this advanced flow sheet. The mass yield of pyrite goldbearing non-magnetic fraction decreased down to 1.5 times in relative to gravity middling. The slurry filtration prior to and after cyanidation allowed the organization of cyanide solution recycling.The results of pilot plant tests using the developed flow sheet showed that the content of pyrrhotite in the non-magnetic fraction decreased from 59.1% to 11.3%. The reagents consumption was 12 kg/t CaO, 3 kg/t NaCN and 16 kg/t Ca(OCl)2 of the pyrite concentrate. The total gold recovery using this flow sheet was 83.4%. Due to a decreased consumption of reagents, cost efficiency of the process was achieved. Based on the results of this research, a project design criteria was developed. A processing plant with the annual throughput of 2.6 million tonnes of ore is being designed."

Jan 1, 2016

By Anthony J. Konya

"This paper was written during part of the author’s student co-op with Cargill Salt at its Avery Islandunderground salt mine in Louisiana. Blasting salt is a unique type of blasting that is different than blasting other rock types. The plastic nature of salt, along with its large swell factor make salt a challenge to blast. The Cargill salt mines use and have tested a variety of different methods for breaking salt in an efficient manner, however these blasting methods are rarely used in other operations nor talked about today."

Jan 1, 2016

By Juergen Antrekowitsch, Stefan Steinlechner

"Waelz oxide from steel mill dust recycling is usually sold to the primary zinc industry, where it is first charged to the roasters to eliminate the remaining fluorides and chlorides. This limits the overall amount of secondary materials which can be used because of different operating problems in the roasters. Another option, in the case where the halides are low, would be direct leaching with low or medium concentrated sulphuric acid. Unfortunately, because of the carryover of some steel mill dust, iron is also present in the Waelz oxide, reaching contents up to 5 wt.%. Since the objective is to treat the solution more or less directly by electrowinning, with only a few simple preliminary purification steps, iron in the solution is a very important factor. Various trials have been done to investigate the dissolution behavior of the iron contained in the Waelz oxide. Although the zinc extraction should reach a maximum, all other elements, especially iron, should be low. This paper describes the results of our research in this area and offers possible options for Waelz oxide utilization. There is also a focus on how other elements, present in the material, influence the dissolution behaviour of zinc and iron, and whether a loss of zinc is unavoidable, if low iron dissolution is required.INTRODUCTION One of the most important secondary zinc resources is the zinc oxide originating from steel mill dust recycling. For the treatment of high zinc containing steel mill dusts, the Waelz kiln process is the so called “best available technology” and it dominates the industry, with roughly a 90% market share. The product Waelz oxide contains mostly zinc oxide, but it also contains lead compounds and halides due to evaporation with the zinc. In addition, it contains iron and some slag compounds due to mechanical carry-over. The presence of halides limits the use of the material as an alternative concentrate for primary zinc electrowinning. Such halides can be reduced to a certain extent by washing and/or solvent extraction (see following chapter). Although lead is not troublesome and theoretically represents a second recoverable valuable metal, iron is unwanted and causes additional problems during leaching. Even though Waelz oxide is generally a highly welcome input material in primary zinc metallurgy, due to its high zinc content, it still contains halides, and in the majority of cases, the oxide must first be treated in a roasting process. Different circumstances, like accretion formation because of the lead and halogen compounds as well as unwanted cooling effects in the roaster, limit the amount of Waelz oxide which can be substituted for the primary concentrate. Another, even more limiting factor, is the allowable concentrations of chlorides and fluorides in zinc electrowinning, the last step in the primary zinc processing route (Ruetten, 2011)."

Jan 1, 2016

By Nickvinder Bhath, Johnson Matthey Plc, Jamie Baker, Daniel Kim, Jeff Lucht, Shijie Wang

"Precious metals (PM) in copper anode slimes are traditionally recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of precious metals, including relatively inert metals such as gold and platinum group metals (PGMs). In this paper, a new method to recover PGM from complex and difficult feed streams is described. Using a proprietary Advanced Ion Exchange (AIX) adsorbent which has a high selectivity for PGMs over other metals and can achieve high PGM mass loadings with a series of incredible pilot test data plus the business case generated from the study results are also presented in the paper.INTRODUCTIONPrecious metals in copper anode slimes are traditional recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of many metals, including relatively inert metals such as gold and platinum group metals (PGMs). Fully hydrometallurgical processes for extraction and recovery of gold and silver from copper anode slimes were employed in major copper refineries since 1995, which was first developed at Rio Tinto Kennecott Utah Copper.In Rio Tinto KUC process, the wet chlorination and gold solvent extraction were utilized to enable recovery of gold and silver as well as other metal compounds. The availability of water and the interaction and amenability of gold processing in water-based solution makes it possible that gold and silver are produced in only five days, compared with a traditional pyrometallurgical process that took 45 days. Most copper refineries are still following the tradition, but the use of hydrometallurgical technologies is increasing as the world demand for metals increases, energy utilization, and environmental viability."

Jan 1, 2016

By Jan Drzymala, Przemyslaw B. Kowalczuk

Froth flotation is widely used for upgrading of ores and other materials. Efficiency of flotation depends on many parameters, including type, chemical structure and dose of flotation reagents. Selection of a proper frother in flotation depends on the material used, necessary dose of frother and its selectivity. The selectivity of flotation can be characterized by proper separation factors and indices. In this paper separation selectivity and power of frothers were evaluated basing on separation data for a given material and frother, plotted as the recovery of the useful component in the concentrate versus the recovery of the remaining components in the tailing. Such a plot is called the Fuerstenau upgrading curve. The selectivity was defined as the location of the whole upgrading curve in relation to no and ideal separation lines, expressed on the scale from 50 (no separation) to 100% (ideal separation). In turn, the flotation power was defined as the dose of frother to reach a certain upgrading level at which recoveries of the useful and unwanted components are equal. The power and selectivity of frothers were determined for the Kupferschiefer stratiform copper ore floated in the presence of a fixed amount of xanthate and varying doses of frothers using a laboratory flotation machine. Basing on the separation results for different poly(propylene glycol) (CnH2n+1O(C3H6O)mH, CnPm) and poly(ethylene glycol) (CnH2n+1O(C2H4O)mH, CnEm) alkyl ethers, it was found that the concentrate yield and recovery of copper as the useful component in the concentrate were greatly influenced by the type and dose of frother. However, the same results plotted in the form of the Fuerstenau upgrading curve clearly indicated that the selectivity of frothers was similar, while their power was different. It proves that both selectivity and power of frothers are useful parameters for characterizing flotation systems.

Jan 1, 2016

By Shingo Morimoto, Toru Sasaki, Masato Shinji

"1. INTRODUCTIONTunnel face stability is one of the most important consideration in New Austrian Tunneling Method. In general, if all of the material properties of ground can be obtained through the field investigations, the tunnel face behavior can be predicted using numerical simulation prior to tunnel construction. However, estimating the safety of a tunnel face is difficult, especially in cases where the ground is very weak such as in an urban area.In this study, numerical analyses of tunnel excavation in very weak ground conditions, such as a low cohesion and low internal friction angle, were carried out. The relationship between the average shear strain distribution on the tunnel face and the overburden was analyzed. This relationship estimates the shear strain of the tunnel face relative to the critical shear strain obtained by the ground properties. The critical shear strain was defined as an allowable value for the maximum shear strain. We proposed the allowable overburden as tunnel face stability index (TFI) that satisfies the critical shear strain criterion of ground. Finally, a design chart of the allowable overburden for various cohesion values and friction angles of ground was created. This chart is useful in the preliminary tunnel design stage to judge the necessity of additional counter measures against normal tunnel support design.2. WEAK GROUND MODELING AND ANALYSIS PROCEDURE2.1 Setting material propertiesWith reference to a past study1), the material properties were adopted on the basis of material properties in the standard worst rock classification case called “DII”2) for standard support pattern of weak ground in Japan. The typical material properties for “DII” are listed in Table 1. In addition, Fig.1 shows the distribution of the representative weak ground according to cohesion and internal friction angle. When the internal friction angle is relatively high and the cohesion is weak, the ground is categorized as sandy ground. Furthermore, when the internal friction angle is low and the cohesion is strong, the ground is categorized as clayey ground."

Jan 1, 2016

By Shengliyang Yang, Jinghu Yang, Jiachen Wang, Xiaomeng Li

"Safe and efficient mining of extremely inclined thick coal seams less than 20m thick is one of the new challenges in China coal industry. In recent years, the extremely inclined thick coal seams have been encountered in some old mines and western China, and currently the top coal caving longwall mining method has been successfully applied to this kind of coal seams. Accordingly, this paper studies the roof movement and its impact on shield supports of top-coal caving longwall mining in extremely inclined thick coal seams. The structure of main roof before failure was simulated by the fix-ended beam, and provided the solutions for determination of maximum compressive stress of the bottom beam end and maximum tensile stress of the top beam end. The failure mode on the upper end of working face is mainly a combination of compression and shearing, while that for the bottom end is tension and shearing. Roof fracture begins at the upper end of working and propagates downward. The shape of collapsed roof strata can be described as parabolic and divided into three segments from top to bottom, including no filling, uneven filling and densely filling segments. The roof loading conditions of no filling segment is more likely to have dynamic burst impacts.INTRODUCTIONExtremely inclined thick coal seam refers to that the dip angle of coal seam is greater than 45° and the thickness is greater than 3.5m (Wang and Zhang, 2015a; Wang and Zhang, 2015b; Wang, 2005; Xie, Gao, and Shangguan, 2005; Wu, et al., 2014; Deng and Wang, 2014; He, et al., 2015). This type of coal seams can be divided into three categories: 1. The extremely inclined thick coal seam, of which the thickness is less than 5m and the dip angle is less than 60°, is usually mined by fully-mechanized longwall mining method. 2. The extremely inclined thick coal seam, of which the thickness is 5 m-20m, is usually mined by top coal caving longwall method. And 3. When the thickness of extremely inclined thick coal seam is greater than 20m, it is mined by the horizontal section top coal caving longwall method. For example, the average angle ofWudong coal mine in Xinjiang province is 45°, and the thickness is 27m. Wudong coal mine is applying the horizontal section top coal caving longwall mining, producing 3 million tons annually per working face (Figure 1)."

Jan 1, 2016

"Classification is an important aspect of mineral processing plants and if not operated efficiently can compromise both the throughput and recovery of the circuit. This paper discusses the benefits that can be obtained by operating the classification section efficiently. Since classification in most of the mineral processing plants is carried out using either hydrocyclones or screens the case studies involving the two classifiers were used in the discussion. Studies where optimising the classification circuit lead to improvements in the performance of the overall plant were included to show the benefits of paying attention to this area that is usually neglected. The data from the mill-float mill float, SABC, and Single Stage SAG mill circuit case studies have shown that the circuit throughput can be increased throughputs without compromising recoveries by optimising the classification circuit. On plants where the ore can be liberated at coarser sizes the experimental results have shown that replacing hydrocyclones with high frequency screens can lead to improved plant throughput with no detrimental effect on recovery. The discussion has included information on design and operational considerations for plants that have or intend to use hydrocyclones or screens that could make the classification circuit more efficient.INTRODUCTIONComminution is the process in which particles are reduced in size mainly by crushing and grinding. In most mineral processing circuits comminution is carried out to liberate the valuable minerals prior to subjecting the ore to a recovery process were values are concentrated or extracted (Mainza, Evertsson, Benzer, Tavares, Powell, Rule, Plint, …, 2013). Comminution is an energy intensive process and is usually achieved in stages. It is common to have a classifier after each comminution stage. The process is carried out in stages to minimize energy usage and to improve the efficiency of the process in meeting product specifications. Although comminution circuits have been advancing classification has remained a key component of the comminution circuit design (Mainza et al., 2013). Mainza et al. (2013) summarised the role of classification in mineral processing circuit as: to allow material in the equipment that can promote high operational efficiency, to improve material handling in the circuit, to minimize overgrinding of material to reduce energy consumption, and to provide the best quality product to enter the next stage of processing. Classification stages are employed in comminution circuits to ensure that high throughputs are processed without compromising the product quality or to produce a fine product at relatively low energy. If neglected classification can have detrimental effects on plant performance."

Jan 1, 2016

By Lifeng Li, Jhon Silva-Castro

In a previous work, the authors analyzed the overlapping probability of two adjacent charges in a single hole for pyrotechnic and electronic detonators. This document extends such work to a complete mine blast where more than two holes are detonated. In a mine blast, all the blast holes are connected as a network by detonators to follow a given initiation sequence. Such initiation sequence’s performance is based on the adequate timing between charges in the mine blast. The analysis of the reliability of a mine blast based on the timing between charges and the initiation type is presented in this document. For a long-run time and under proposed operating conditions, the reliability of the mine blast can be analyzed based on the network which is treated as a system. The failure of the system is defined as no success between any two delays charges either in a single hole or in between two holes.

Jan 1, 2016

By Thierry Lavoie, Mark K. Larson

"Engineers at the National Institute for Occupational Safety and Health (NIOSH) and Itasca Consulting Group, Inc., conducted a study to determine the procedure for calibrating a caving model implemented in FLAC3D. The model is calibrated to measured surface subsidence. This sedimentary caving model was developed by Itasca for NIOSH for the purpose of more closely simulating mechanical processes during caving. When a model is considered calibrated to surface subsidence, the load between the extracted panel's roof and floor is a reasonable estimate of gob loading. Such information can also provide an estimate of the amount of overpanel weight that is transferred to the abutment. This load distribution is a parameter needed, for example, to estimate loading of pillars in longwall gate roads. For the current case, a calibrated model resulted in a calculated abutment angle of 30.6°considerably higher than the assumed value used in empirical methods, but reasonable considering the presence of massive stratigraphic members in the overburden. Because of additional information available after this study that the extracted seam height was actually greater in the first panel, a corrected range of abutment angle was estimated to be from 27.7° to 30.6°, still significantly higher than the empirical assumption. The expectation is that better estimates of abutment loading profiles will result in improved evaluations of mine layout design and, therefore, reduce the number of fatalities and injuries resulting from falls of ground.INTRODUCTIONThe safety of miners in underground coal mines depends on careful consideration of the mechanisms involved in failure and transfer of load. The successful design of pillars and panels in longwall and room-and-pillar coal mining requires thorough attention to any information and measurements available that help understand these mechanisms. Although empirical methods, such as Analysis of Pillar Stability (ALPS) Mark (1987); (Mark, 1992) or Analysis of Retreat Mining Pillar Stability (ARMPS) (Mark and Chase, 1997), can provide a sense of success or failure, complex geology and failure in the roof or floor material or complex material behavior of the coal can make evaluation by an appropriate numerical modeling tool necessary. The numerical tool must simulate important mechanisms and appropriate detail that underlie the mechanism. For example, Starfield and Cundall (1988) advised using ""the simplest model that will allow the important mechanisms to occur, and could serve as a laboratory for the experiments you have in mind."" To that end, data gathering about the geology, geometry, and material behavior is very valuable. Such data facilitate selection of an appropriate model and model inputs. Moreover, this data facilitate improved assessment of risk to miners and how to minimize that risk."

Jan 1, 2016

By P. J. Petit

"The complex planning required to achieve any planned production yields multiple and dissociated responses over the life of project (LOP). The customary decision-making process negates the possibilities of developing optimized and integral solutions from operating levels up to business and strategic levels. This results in an inefficient project or overall underperformance of the operation.In the project setting, disconnected trade-offs and improved performance studies become inadequate, because they are site-specific and use only a few comparative parameters. They are often based on a small data-set.Decisions taken to achieve overall objectives require the correct determination and dissemination of key performance indicators (KPIs). The KPIs indicate efficiency in operation, whereby the marginal rate of technical substitution corresponds to the rate of production. It is the necessary condition for optimization. Performance realization for sustainability follows optimization modelling, the latter often being presented with financial results such as business net present value (NPV). It considers techno-financial constraints and provides a strategic and aligned outlook of KPI decisions for an enhanced and integrated outcome.This paper explains a mining case study that is rendered efficient, and through business optimization (BO) short-term and sustainable targets are reached. Business optimization increases the NPV by 14.7%. This is achieved by challenging conventional decision-making associated with maximizing business value by including environmental externalities within the LOP."

Jan 1, 2016

By Francisca San Martin, Tomas Vargas, Willy Kracht

"In Cu-Mo deposits it is usual to find considerable amounts of pyrite (FeS2). When processing this kind of ore by flotation, pyrite is rejected using lime to increase the pH to alkaline conditions (pH ~10.5). In the case of using seawater without pre-processing, i.e., raw seawater, the lime consumption increases dramatically and the recovery of molybdenite drops due to the precipitation of magnesium hydroxide on its surface. In order to avoid these negative effects, alternative ways of depressing pyrite should be considered.The current work introduces the use of Acidithiobacillus ferrooxidans, bacteria commonly used in bioleaching, as an alternative to depress pyrite in seawater flotation. The paper presents the results of biodepression in three systems: fresh water, water with added sodium chloride at 35 g/L (which corresponds to the salt concentration in seawater ) and seawater. The results show that it is possible to bio-depress pyrite with A. ferrooxidans in natural seawater pH (7.8-8.2). A similar behaviour is observed when running the experiments in fresh water, and in water with sodium chloride added.INTRODUCTIONWater is a scarce but essential resource for human development. The main reason for this scarcity is that, although 70% of the earth's surface is covered with water, only 3% of the total is fresh water and an important part of this water is frozen, so that only 1% of fresh surface water can be used for human activities. In Chile, most of the mining activity is concentrated in the north of the country, located in the Atacama Desert, considered the world's driest desert. That is why some mining companies have chosen to use seawater in their processes. For example, Esperanza (Antofagasta Minerals), and Sierra Gorda (KGHM International) use raw seawater in their flotation processes."

Jan 1, 2016

By M. Poulton, J. A. Botín, C. Gatica

"The Chilean minerals industry faces a shortage of 27.000 new skilled professional by 2023. Enhancing the integration of women into the workforce is a possible solution. This study analyzes the state of women in the mining workforce over the past decade. Several key indicators are presented: percent in the workforce, salaries, career profiles, presence at management level, and participation in academia are studied. The study also analyzes the strategies used by government, industry, and universities to recruit and retain women for the minerals industry. The main results show that women represent 7.4% of the mining workforce in Chile and less than 1% of senior positions with a salary gap of approximately 30%. Systematically, women prefer professional programs in geology, chemistry, and environmental areas. The Chilean statistics are compared to data from the United States mining industry. INTRODUCTION The Chilean mining industry faces a significant shortage of professionals for the next decade which compromises competitiveness and productivity. The demand for human capital in mining depends on several factors. First, the age structure of workforce, which determines future retirement needs. Second, minerals market considerations, determining the amount and size of mining projects entering production in the coming years. Third, the evolution, positive or negative, of productivity, mainly driven by technology and innovation, and negatively affected by the declining ore grades. Finally, negative trends in lead times to production of mining projects, due to social opposition, changing regulations and other project contingencies, negatively affecting the demand for human capital. Regarding the supply of human capital, the fast increase in the technology level of the minerals industry and hence, the increase of technical qualification requirements of the human capital generates a rise in the time required for trade and university education of mining professionals, which may cause imbalances in the labor market. According to (Consejo Minero, 2014) human capital gap in Chile by 2023 will be around 27.000 workers for extractive, processing and maintenance jobs, which represents 14% of the current workforce (Figure 1)."

Jan 1, 2016

By Brent A. Slaker, Khaled M. Mohamed

"Understanding coal mine rib behavior is important for inferring pillar loading conditions as well as ensuring the safety of miners who are regularly exposed to ribs. Due to the variability in the geometry of underground openings and ground behavior, point measurements often fail to capture the true movement of mine workings. Photogrammetry is a potentially fast, cheap, and precise supplemental measurement tool in comparison to extensometers, tape measures, or laser range meters, but its application in underground coal has been limited. The practical use of photogrammetry was tested at the Safety Research Coal Mine, National Institute for Occupational Safety and Health (NIOSH). A commercially available, Digital Single-Lens Reflex (DSLR) camera was used to perform the photogrammetric surveys for the experiment. Several experiments were performed using different lighting conditions, distances to subject, camera settings, and photograph overlaps, with results summarized as follows: The lighting method was found to be insignificant if the scene was appropriately illuminated. It was found that the distance to the subject has a minimal impact on result accuracy, and that camera settings have a significant impact on the photogrammetric quality of images. An increasing photograph resolution was preferable when measuring plane orientations; otherwise a high point cloud density would likely be excessive. Focal Ratio (F-stop) changes affect the depth of field and image quality in situations where multiple angles are necessary to survey cleat orientations. Photograph overlap is very important to proper three-dimensional reconstruction, and at least 60% overlap between photograph pairs is ideal to avoid unnecessary post-processing. The suggestions and guidelines proposed are designed to increase the quality of photogrammetry inputs and outputs as well as minimize processing time, and serve as a starting point for an underground coal photogrammetry study.INTRODUCTIONThe stability of underground mine ribs has been a safety concern for underground coal mines for decades. Unfortunately, the average rib fatality rate has been about 1.3 per year between 1996 and 2013 (Jones et al., 2014). In an effort to better understand coal rib behavior, photogrammetry is being investigated in this study as a measurement tool for surveying ribs in an underground coal mine environment."

Jan 1, 2016

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016