Search Documents

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

By M. C. Harris

"In the flotation process the contact angle is an important indicator of the hydrophobicity of a mineral particle. There is considerable literature showing that the contact angle increases when the chain length of the alkyl group associated with the collector molecule used to render the valuable mineral particle hydrophobic increases. The extent to which an alkyl group interacts with surrounding water molecules is quantified thermodynamically by the excess Gibbs energy. In the present paper it is shown that there exists generally a strong linear relationship between the excess Gibbs energy of the alkyl group associated with the collector and the contact angle. The structure-activity of such alkyl groups is in turn related to the total surface area, molecular volume, the molar volume, molecular weight of the functional groups in the molecule and interaction energies. It is proposed that the demonstrated relationship is indicative of the role which the alkyl group component of the collector, which is attached to the mineral particle, plays in increasing the extent to which water molecules at the surface of the mineral are rejected from the surface thus increasing the contact angle. The relationship between excess Gibbs energy and surface tension is further explored with a view to relating the observations quantitatively to the parameters in the Young equation.INTRODUCTIONThe issue of wettability of materials is of great importance to many industrial applications. Wettability studies usually involve the measurement of contact angles which indicate the degree of wetting when a solid and liquid interact. As is well known the contact angle (O) is the angle between planes tangent to the surfaces of the solid and the liquid at the wetting perimeter which is the zone where the air, water and solid phase merge. When the air bubble attaches to the solid surface there is an increase in the air/solid interface area and a decrease in the solid/water interface area. For attachment to occur the cosine of the contact angle should be less than 1 and this will be promoted if the interfacial surface tension between the air and the solid (? SV) is low. Classically the relationship between these parameters has been expressed through the Young equation (1) for a perfectly flat surface:"

Jan 1, 2018

By P. Knüpfer, B. Babel, M. Rudolph, F. Perez Maldonado, U. A. Peuker, L. Ditscherlein

"In heterocoagulation processes for the separation of mineral particles, the most famous being froth flotation, the main characteristic of separation is a differing wettability of the constituents to be separated. This most crucial property in the economically important process of flotation is often only and incompletely, quantitatively described in terms of contact angles against water. A water contact angle larger than 90° is referred to as hydrophobic and hydrophilic vice versa. Looking at Young’s equation shows that it is actually the surface energy of the solid in interaction with the surrounding phases and their surface energies (or surface tensions for liquids) which describes whether there will be hydrophobic/hydrophilic hydration interactions leading to attraction or repulsion. This, we have previously published for various more or less hydrophobic minerals in correlation to their flotation response, i.e. flotability (c.f. Rudolph & Hartmann, Coll.Surf.A 513, 380-388). In the same paper we also discussed the heterogeneity of wettabilities as assessed with the novel method of inverse gas chromatography. Furthermore we have also reported on hydrophobic force distributions as assessed with atomic force microscopy which are as well due to wettability heterogeneities (c.f. Fritzsche et al., Coll.Surf.A 459, 166-171).In this paper we present wettability distributions of different substrates and particles with various surface roughnesses/shapes and degrees of hydrophobization as assessed with iGC, AFM and dynamic sessile drop analyses. We are putting the results in context in unifying models and present methodologies helpful to make use of the fundamental information and their impact on the actual industrial separation process in fundamental process models. Besides froth flotation we also emphasize the impact on selective hydrophobic flocculation process."

Jan 1, 2018

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

By I. Nishkov, I. Grigorova, M. Ranchev, S. Dzhamyarov

"Chelopech concentrator (part of Dundee Precious Metals) is located in central-western Bulgaria. The current process plant utilizes conventional primary crushing and SAG mill grinding, copper and pyrite rougher and cleaner flotation stages to produce a marketable gold-rich copper and pyrite concentrates. As in the most processing plants, the pyrite depression is carried out alkaline media using lime. The subsequent activation of pyrite mineral is achieved by adding sulfuric acid, which has an adverse effect on the flotation equipment. Therefore, a series of laboratory flotation experiment for activation of lime depressed pyrite by ammonium salts, such as ammonium chloride (NH4Cl), ammonium sulfate (NH4)2SO4 and ammonium bicarbonate (NH4HCO3), have been conducted. The obtained results showed that ammonium bicarbonate proved to be the most appropriate reagent choice for pyrite mineral activation. These results are confirmed by X-ray photoelectron spectroscopy (XPS), performed to determine the surface chemistry of pyrite in its natural state, after lime treatment and subsequent treatment by NH4HCO3. The registered XPS spectra indicate that the hydrophilic phases on the pyrite surface could be efficiently removed by using the ammonium salt NH4HCO3. The industrial use of NH4HCO3 as an activator of lime-depressed pyrite is a possible alternative for sulfuric acid replacement as a most widely used pyrite activator. Flotation experiments with addition of 200, 400, 600 and 800 g/t from each of the studied ammonium salts have been conducted. Furthermore, the impact of the flotation pulp pH within the scope of 9.00 – 10.50 was also investigated. The obtained results from the laboratory flotation experiments, showed that the pyrite activation with ammonium bicarbonate is an excellent possibility for replacing the sulfuric acid as main pyrite activator reagent, in order to eliminate the gypsum accumulation during the flotation of pyrite in Chelopech concentrator.INTRODUCTION The Chelopech deposit, located about 60 km east of Sofia is one of the largest Cu-Au deposits in Europe. The ore have complicated mineralogical and chemical composition. The main ore minerals are represented by pyrite, enargite (luzonite), tennantite, chalcopyrite and bornite. The average copper content of the mined ore is about 1.1 % and the gold content is about 4.0 g/t."

Jan 1, 2018

"Mining used to be a business primarily focused on the technical aspects of getting valuable ore out of the ground and extracting the minerals efficiently. Without denying the importance of these skills, a narrow focus on technical issues is no longer enough to guarantee success when it comes to exploiting rare earth element (REE) deposits. Molycorp failed to enter the global REE market in a successful manner, while none of the many REE exploration projects has turned into an active mine so far and none is expected to commence operations in the near future. Accordingly, the world of REE is far more complex compared to other commodities. This paper looks into the REE industry to identify the factors that can connect potential U.S. REE mines to the market. The ability to break free from past thinking and become future-focused is a key driver. Mining of REE is pointless without a corresponding value-adding chain, while developing a value chain without first establishing an uninterruptible source of REE is also senseless. The mining sector must be based on the REE value chain and vice versa, along with the establishment of a market channel for the REE products that come out of the mine. INTRODUCTION It has been seven years since rare earth elements became the subjects of front-page headlines. It was when the controversial Chinese export policy for these critical commodities was epitomised in a maritime border dispute with Japan in September 2010 that resulted in the big REE crisis and price spike of 2011 (Barakos et al, 2016c; Mancheri, 2015). The world was dismayed, especially in REE-importing countries, such as the United States that was and is still totally dependent on Chinese production and exports (Barakos et al, 2016c; Kennedy, 2015). The short-lived alarm initiated a treasure hunt by way of exploration for REE deposits all over the world. The continuously growing demand on the one hand and the Chinese sovereignty of the REE-market on the other, led the rest of the world to explore their own REE resources. In just a few years, more than 400 projects were initiated to explore REE deposits outside of China (ERECON, 2015; Goodenough, 2016). The prices of REE, however, dropped rapidly and at the moment of writing this paper are in 6-year lows, at the level of the price average before the 2011 crisis (Barakos, 2017). The viability of even major established producers is being challenged, not to mention the development prospects of potential REE-market entrants (Barakos et al, 2016b; Rollat et al, 2016). Production cutbacks and industry consolidation in China impel REE market experts to forecast that prices have already reached their lowest point and have nowhere to go but up (Adamas, 2015; Roskill 2015). Yet, expectations for increased REE prices are limited and drastic changes are unlikely to happen in the near future, as there is still excess supply in the overall REE market (Barakos, 2017). Nevertheless, the low prices of rare earths are not the only reason that potential producers are struggling to enter the global REE market. Among other parameters, the separation of the individual elements seems to be the most important factor, as it is technically challenging and expensive to build and to operate."

Jan 1, 2018

By T. Fraszczak, U. A. Peuker, T. Mütze, T. Leißner, A. Wikedzi

The present paper highlights on the comminution and liberation properties of two greisen-type lithium bearing-mica ore blends (L1, L2) subjected to different breakage devices; cone crusher (CC), roller crusher (RC), rotor beater mill (RBM) and a screen mill (SM). The particle size distribution (PSD) of the products from each device were evaluated to search for an appropriate PSD model using Gates-Gaudin-Schuhmann (GGS) and Rosin-Rammler (RR) functions. In order to determine an appropriate function that could better describe the PSDs from the devices used, the coefficient of determination (R2) was used as a criterion. In terms of mineral liberation studies, due to costs, only products from rotor beater mill (RBM) were examined through an automated scanning electron microscope (SEM) technique. It was found that RBM, RC and SM products were better described by the RR model than the GGS model with higher R2 values (0.97-1.0). However, cone crusher products for L1 were better described by GSS model, while that for L2 were better described by RR model. In terms of the spread of size distribution as indicated by RR model parameters, RC products were more uniformly distributed compared to products from other devices, for both ore blends. Also the RBM products were more scattered than products from other devices. The results indicate that the composition of individual ore blends affected the comminution products PSDs since different PSD model parameters were obtained for samples comminuted by same devices. The modal mineralogy of the two ore blends indicate both to be rich in quartz, topaz, zinnwaldite and muscovite. Further, the result indicate that, for both ore blends, zinnwaldite phase is more enriched in the fraction < 250 µm. Moreover, better liberation of zinnwaldite is observed for L1 compared to L2. This could be explained by differences of the two ore blends in three aspects; the nature of mineral association, reduction ratio of the fractions analysed and the nature of spread of the size distribution.

Jan 1, 2018

By D. Saramak

"High-pressure grinding technology is considered as one of the most efficient techniques of ore comminution, especially in terms of energy consumption. HPGR devices has been utilized in many mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Even though the technology well known (introduced into mineral processing circuits in 80’s), there are still examples of ineffective operation of HPGR devices. This is a result of improper application of HPGR into individual crushing circuit. The purpose of the paper was to analyze selected effects achieved in HPGR on the course and effectiveness of beneficiation operations. Investigations were carried out for copper ore, and investigative programme was run for different values of HPGR pressing force, as well as changeable ore characteristics (content of fine size fractions, material moisture). All crushing products were then treated in flotation process, in order to determine useful mineral recovery. Results of investigations show that HPGR operating pressure influences the metal recovery in proportional way, however too extensive pressure values have relatively lower impact on increasing of the metal recovery. Particle size distribution of HPGR feed and its moisture have lower influence on recovery level than HPGR pressure, but too extensive moisture content influences the higher energy consumption of the roller press, together with less effective comminution. The second aspect raised in the paper was a possibility to control and optimize the HPGR-based circuit. There were presented the proposed approach to adjustment of HPGR operating parameters that enables the higher metal recovery.INTRODUCTION The high-pressure grinding technology, invented and developed by Professor Schoenert in 70’s (Schoenert, 1979), is currently regarded as one of the most efficient methods of hard ore comminution. Since then the technology was introduced into raw materials treatment circuits in many mining and mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Considerable number of works concerning modeling and optimization of HPGR operation were also presented (Daniel & Morell, 2004, Tavares, 2005, Saramak, 2012, Saramak & Kleiv, 2013). Nowadays high-pressure grinding rolls devices are considered as well know technology with over 500 sold machines, according to various sources."

Jan 1, 2018

By Y. S. Sun, P. Gao

"In this investigation, a pilot-scale suspension magnetization roasting reactor was introduced and used to enhance magnetic properties of an iron ore. Consequently, the effects of roasting temperature, reducing gas CO flow rate and fluidizing gas N2 flow rate on the magnetization roasting performance were investigated. The results indicate that the hematite and siderite are almost completely converted into magnetite by a gas mixture of 3.5 Nm3/h CO and 2 Nm3/h N2 at roasting temperature of 520 °C. Under the optimized conditions, the magnetic iron concentrate with an iron grade of 60.18% and iron recovery of 90.17% was achieved. The XRD and Fe mineral phase analyses revealed that most of the hematite and siderite were converted to magnetite, and the magnetic properties were greatly enhanced. INTRODUCTION The steel and iron industry in China has rapidly developed in recent years requiring a large quantity of iron ores. Low-grade and complex iron ores are currently the overwhelmingly dominant mineral resource for iron in China. Therefore, China depends on imported iron ore resources heavily, resulting in an increase in the production costs of iron-making and steel-making[1-3]. Using domestic resources to produce a steady supply of high-quality iron ores is an important step toward the sustainable development of the steel and iron industry[4-5]. The iron ore from Jiuquan iron and steel company is abundant and recognized as typically complex iron ore resources in China. Magnetization roasting followed by low-intensity magnetic separation has been proven as the most feasible methods to upgrade refractory iron ore[6-10]. In present research, an innovative roasting technology, namely suspension magnetization roasting, was developed and applied to recover iron from a typical refractory iron ore. Suspension magnetization roasting technique and equipment developed by Prof. Yuexin Han’s Group at Northeastern University (NEU) is an effective way for the utilization of refractory iron ore. The advent of suspension magnetization roasting will, in China and even globally, produce a significant technological revolution in the field of iron ore beneficiation. Based on the previous works, this paper mainly described experiments on the separation and recovery of iron from a complex refractory iron ore by means of suspension magnetizing roasting and low-intensity magnetic separation processes. The purpose of the research is providing a new technology for effective utilization of refractory iron ore. Process parameters that affected the separation and recovery rate of iron were conducted and optimized, and the reaction process was analyzed by XRD and Fe mineral phase analysis."

Jan 1, 2018

By Edgar Schach, Tom Leistner, Markus Buchmann, Urs A. Peuker, Martin Rudolph, Marius Kern

"In this study, the flotation characteristics of a cassiterite-bearing fine-grained and complex skarn ore from a deposit in the Ore Mountains is investigated. The tests are performed using an oil-assisted column flotation approach to process very fine ore fractions and avoid losses of cassiterite into the tailings. First, process parameters are obtained for a finely ground artificial mixture of quartz, magnetite and cassiterite, simulating the real ore. Thereby, magnetite is used, as iron oxides can have a detrimental effect on the flotation due to a similar flotation behavior. In addition, they can act as a source of multivalent ions, which are known to reduce the concentration of collector molecules, active for flotation. Based on the results, selected parameters are further tested for cassiterite skarn ore from the Hämmerlein deposit including a pre-conditioning and a water exchange step to remove ionic contaminants. The process response is analyzed in detail by XRF (X-ray fluorescence) and MLA (mineral liberation analysis) to get a better understanding of the behavior of the single ore components. Sulfosuccinamate type surfactant is utilized as the collector, emulsifier and to reduce the froth destabilization through nonpolar oil. Sodium hexafluorosilicate is added as the depressant.INTRODUCTION Complex skarn ore deposits containing considerable amounts of tin, indium and other metals are located in the Ore Mountains region (Germany). In this study, a skarn ore from the Hämmerlein deposit was investigated. Due to the finely disseminated nature of this ore, past beneficiation attempts failed, and the ore was considered economically unprocessable. However, increasing resource demands brings it back into focus (Schuppan and Hiller, 2012). Cassiterite is the main tin bearing mineral in this ore. Due to its high density (~7 g/cm³), the predominant beneficiation technique is gravity separation (Angadi et al., 2015). Tin ores from disseminated deposits have to be extensively comminuted to reach a sufficient degree of liberation of the cassiterite grains. As cassiterite has a brittle nature, it is preferable enriched in small size fractions, during comminution (Angadi et al., 2015). Gravity separation methods become more and more inefficient for particles smaller 40 µm (Falcon, 1982), causing tin losses of up to 30 to 40wt.-% (Angadi et al., 2015). Thus, froth flotation of cassiterite was first utilized in Altenberg in the Ore Mountains as an additional processing step to reduce the cassiterite losses into gravity separation tailings (Bulatovic, 2010; Gruner and Bilsing, 1992). Although the reported lower size limits for an effective cassiterite floatability are often smaller compared to other minerals, the flotation performance is in general decreasing for small particle sizes < 10 µm (Trahar and Warren, 1976). Therefore, different approaches have been already investigated for the flotation of such fine cassiterite fractions to overcome the limits in particle size. Bilgen et al. investigated the shear flocculation of cassiterite with a sulfosuccinamate collector (Bilgen et al., 1994). The agglomeration flotation of cassiterite has been tested by Schubert et al. (Schubert et al., 1966), in which the selective coagulation of fine hydrophobic particles and oil droplets leads to an increase of the effective particle size. Recently, Leistner at al. investigated an oil-assisted agglomeration flotation for ultra-fine cassiterite ore fractions (Leistner et al., 2016). However, a poor response due to an increased concentration of Fe and Ca ions, unselective oil/gangue coagulation and froth instability, that is caused by oil/frother interactions, has been observed."

Jan 1, 2018

By A. V. Bogdanovich, S. A. Urnysheva

"Gravity and X-ray luminescent separation methods are generally used in processing of diamond ores. X-ray luminescent separators are applied for separation of diamonds from feed ore size fractions from 100 to 10-15 mm size and for final treatment of gravity concentrates over 1 mm size. Gravity separation machines used for diamond ores separation are heavy medium cyclones and pneumatic jigs. One of the most important parameters, to a large extent affecting diamonds recovery from ore, as well as processing costs and specific energy costs, is size of dumped final tailings. That was exactly the purpose of the studies, the results of which are described in this paper. The studies performed on different ores showed that in order to achieve high recovery results, it is necessary to dump heavy medium separation tailings below 3 mm size. Separation of final tailings of -6+1 mm size by jigging is also possible. However, with a view to exclude extra diamond losses, it is necessary to maintain jigging concentrate yield approximately at 25% from starting feed, with its subsequent cleaning in heavy medium cyclones. In addition to that, it is necessary to separate 20-25% of middling with diamonds content at feed ore level and subject it to grinding. This will complicate flow sheet, but reduce load on heavy medium cyclones. In order to develop optimal flow sheet for gravity concentration of a specific diamond ore, large-scale investigations are required, including technical-and-economic assessment of separation alternatives. INTRODUCTION In processing of diamond ores, gravity and X-ray luminescent separation methods are generally used. It is common practice to apply X-ray luminescent separators for separation of diamonds from feed ore size fractions from 50 (100) to 20 (10) mm size and for final treatment of gravity concentrates over 1 mm size. With that, X-ray luminescent separation tailings larger than 3-6 mm size are reground and delivered to gravity concentration processing stage. Middling products circulation volumes are large, not infrequently necessitating decrease in concentrating plants capacity, especially with mining in deep workings of deposits, where ore strength is higher (Goryachev, 2010; Vaginov, 2000; William, 1988). Diamond ores preparation before processing is accomplished by means of roll-screw crushers and autogenous grinding mills, minimizing probability of free diamonds damage in liberation from barren rock. In re-crushing of size fractions that are “difficult” in autogenous grinding, high pressure grinding rollers are applied (Burchardt, 2014; Fedotov, 2011a, 2006b)."

Jan 1, 2018

By Francisco Sena Leite, Vinicius Miranda

Mine blasting is directly associated with ground vibration. If these affect critical structures (buildings pit walls, etc.) they must be mitigated to reduce the environment and social impacts. Vibration monitoring and control is one of the most important procedures in blasting because it will impact short and long term incidents associated with this blast effect. Technology moves ever forward, and today we have personal devices that are equipped with an array of sensors, for that reason the authors decided to investigate the possibility of using a personal device to do vibration control. This case study compares the same blast measured with a traditional seismograph and a smartphone. To validate this new methodology, attenuation laws were built with data from a traditional seismograph and a smartphone application. Predictions were also made prior to a set of blasts. Residual analysis was used for data validation from the two different sources. From the performed analysis, to prove the validity of this new methodology, the normality tests for statistics residues analysis proves that it is possible to infer that the model has a null residual mean and a small residual error. The achieved results show the accuracy of these devices, the authors pretend to show the potential of this equipment and open a completely new door for vibration analysis.

Jan 1, 2018

By J. A. Dos Santos

"INTRODUCTION Dramatic reduction in energy use and environmental impact can be achieved with sandwich belt high angle conveyors that serve as the vital link in any IPCC (In-pit Crushing and Conveying) system. These high angle conveyors are not new at all, but have not found wide use in IPCC systems where they can realize the greatest advantage. Reduced energy consumption and environmental impact, with IPCC systems, was already realized in the 1970s. With the bulk material haulage limited to conventional open trough conveyors the most direct path out of the open pit was precluded, requiring low angle spiral ramps and/or deep slots and/or tunnels through the high wall of the open pit. These excavations, to accommodate the low angle limitations, represented undesirable impact on cost and on the environment. Against this backdrop, a major study in 1979 sought to develop high angle conveying systems that could continuously haul the mined bulk material directly out of the pit, along the high wall – the shortest distance between the two end points. Between 1979 and 1982, that study developed sandwich belt high angle conveying systems that utilized all conventional conveyor equipment including smooth surfaced rubber belts that could be continuously scraped clean. These systems had all of the positive features of conventional conveyors but overcame the angle limitation. By hugging the bulk material between two belts, the material’s internal friction could be developed to facilitate conveying at any high angle up to 90 degrees (vertical). After an intense testing period (about one year) on the first large scale prototype system, commercialization began in 1983 with the installation of a 60 degree incline system at a western United States coal mine, elevating 2000 t/h of coal to a train load out system. It did not take a long period of scrutiny and acceptance before this high angle conveyor found use in the most rugged requirements of an IPCC system. This was only the second commercial sale, and after more than 150 commercial installations, it remains arguably the most significant high angle conveying system. In 1984, a copper mine in Serbia, already using pit perimeter crushing and conveying, decided to move their primary crusher deep into the pit and to use a sandwich belt high angle conveying system to elevate the ore continuously, directly out of the pit, along the high wall to the pit perimeter where it then transferred to a conventional conveyor for the remaining haul to the plant. The system had significant features including 2000mm wide belts that elevated 250mm coarse ore, at 4000 t/h, over six 15-meter high benches for a total 90 meters of net lift. The system was able to reduce the truck haulage fleet by ten 200 ton trucks realizing great cost savings, zero emissions to the air and greatly reduced traffic congestion in the pit. The system operated successfully until 2002 when the mine shut down. Many successful sandwich belt high angle conveyors followed with the current count of commercial installations at more than 150. Despite the great success with this system, its use has not been repeated as part of an IPCC system."

Jan 1, 2018

By L. E. Veki, S. M. Luukkanen, J. P. Karvonen, J. O. Leppinen

Today there is a consensus that xanthate adsorption on sulfide minerals is primarily controlled by redox reactions occurring at specific potentials on these semi-conductive minerals. Consequently, it is possible to control xanthate adsorption by controlling electrochemical conditions in the system by using oxidizing and reducing agents. The scope of this study was to investigate the possibilities to increase the selectivity of Cu-Fe-Zn ore flotation by applying electrochemical control in the conditioning of the flotation feed. In this work, mild steel grinding in a nitrogen atmosphere was used as the basis to provide a negative starting potential and minimize the amount of oxidation products on sulfide mineral surfaces. To study how different potential levels affect flotation results, a controlled conditioning procedure was utilized maintaining potential at a desired level by titrating the pulp with air. Xanthate adsorption kinetics during conditioning was examined by taking pulp samples for spectrophotometric analysis and laboratory flotation tests were conducted for samples that underwent the controlled conditioning procedure in the potential range of -200mV to +200mV vs. SHE. A clear correlation was detected between chalcopyrite recovery and the potential during controlled conditioning indicating that there was a constant increase in chalcopyrite recovery when the potential was shifted to more anodic values. It is possible that utilizing potential control in the conditioning stage, a smelter grade copper concentrate can be achieved directly in rougher flotation without cleaning stages. Conditioning in favorable conditions had significant positive effects on flotation selectivity of chalcopyrite. The improvement in copper concentrate grade being predominantly caused by the depression of pyrite. By applying the controlled conditioning procedure pyrite recovery in rougher flotation was reduced even low as under 1%, while in the tests without controlled conditioning, pyrite recovery varied between 7.5 – 65.7%. The result of this work indicate that affecting collector adsorption by electrochemical control in the conditioning stage can provide significant improvement in sulfide mineral flotation and industrial applications could lead to decreased chemical consumption, reduced equipment and maintenance costs.

Jan 1, 2018

By C. A. C. Sequeira, G. N. Anastassakis

"The separation of fine or even smaller size mineral particles with conventional methods is inefficient due to the specific properties of fines (small mass, high specific surface area, and high surface energy per unit area). Hence, the production of high-grade concentrate with high recovery is very difficult to impossible and a significant share of mineral values is lost to the tailings. The aim of the current research is to investigate the possibility to efficiently separate value minerals from gangue of fine particle size. The objective of the current work is to develop separation schemes of fine mineral particles by combining an initial stage of particles agglomeration with the use of collectors (hydrophobic agglomeration) with a subsequent conventional separation method. In the current research, magnesite was used as mineral value to be separated: a) from quartz, and b) from mineral mixture (serpentine, ilmenite, and olivine). In each case, tests on single minerals and artificial mixtures were carried out. After hydrophobic agglomeration, the separation of magnesite from quartz was achieved by settling; in the second case (gangue: serpentine, ilmenite, and olivine), magnetic separation of the co-agglomerated gangue was applied. In both cases, the results of the preliminary tests on single minerals suggest that the separation of mineral value is feasible and efficient. These findings were also confirmed from the results of the tests on artificial mixtures of magnesite and gangue, either quartz only or mineral mixture. Both separation schemes provided with magnesite concentrates of commercial grade (95% magnesite) with high recovery. INTRODUCTION The generation of fine particles is inevitable in many operations of mineral commodities processing. Especially in the case of low-grade ores, the mineral value is finely disseminated in the ore, and considerable liberation occurs at a fine size range. Although there is not a uniform classification system with respect to mineral particles size, fines are usually characterized the particles with a size range of -100µm+20µm, very fines those of -20µm+5µm, ultra fines of -5µm+1µm, and colloids smaller than 1µm (Sivamohan, 1990)."

Jan 1, 2018

By Matt Slezak, Tristan Worsey, Nathan Rouse, Kyle Hall

As everyone knows, blasters are required to file blast reports of every blast for regulatory purposes. To this day, the authors see many handwritten blast reports. Handwritten blast reports are notorious for containing errors or omissions. This is not because the blaster intends to misreport information. It is because blasters have many tasks to complete in a day, are sometimes in a rush, and could accidentally miscalculate data, omit items, or record incorrect data. In most cases, blasters do not suffer consequences to these errors because blast reports are seldom reviewed in detail. In some cases, such as when a blasting operation undergoes some sort of litigation process, the reports are reviewed in detail and the blaster is ultimately held responsible. If the reports contain errors, the blaster can be fined, have his/her license revoked, or worse. Electronic blast reporting and centralized data management can help reduce or eliminate the potential for accidental blast reporting errors to occur. This paper presents many ways that electronic blast reporting can reduce or eliminate blast reporting errors, decrease time and extra costs spent reporting, and improve efficiencies in the field and the office.

Jan 1, 2018

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By A. P. Chaves, D. Jose Neto, M. G. Bergerman, E. S. Mano

"More complex ore comminution and concentration operations have found increasing application in the mining industry due to lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. They allow removing a significant mass of material with little or no content of the relevant mineral before the ore is fed into the processing plant, with the consequent reduction in the mass to be processed in downstream operations. Significant benefits arise out of the use of pre-concentration, such as higher contained metal output without the need to increase the grinding or flotation capacity, and longer mine life. The grade of marginal ores could be enhanced to a level that would make their exploration economically feasible, which would result in increasing exploitable reserves. Nevertheless, few studies to date have assessed the resulting impacts on ore grinding energy consumption and wear after the gangue is removed through pre-concentration operations. This study evaluated the energy consumption and wear of grinding circuits in Brazilian mining operations in which the feed has gone through a pre-concentration stage. Such assessment was based on different samples of sulfide and oxide ores. Laboratory tests were carried out to investigate the power consumption and wear of grinding circuits with and without a pre-concentration stage. Laboratory test results were used to simulate industrial grinding circuits based on both alternatives and illustrate the environmental and economic benefits of each one.INTRODUCTION Increasingly complex ore concentration operations in several stages have found broadening application in recent years in view of lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. Different ore processing technologies can be used for that purpose, such as magnetic separation, density segregation, and separation methods based on high-tech sensors (ore sorting). Currently, the most common methods are gravimetric processes, in view of their low cost, particularly jigging and dense medium separation methods, such as the drum and cone separators manufactured by Western Machinery Company, Teska, Drewboy, Norwalt, Dynawhirlpool and Tri-flo, and dense medium cyclones (CAMPOS; LUZ; BRAGA, 2010). The use of dry ore sorters has also grown significantly in recent years (Jose Neto et al. 2017). The selection of the separator type depends essentially on the ore particle size, required flows, and operating density ranges. All these methods may even be used after preferential blasting in mining (Grigg & Delemontex, 2015)."

Jan 1, 2018

By S. A. Kubyshkin, A. A. Agafonov, A. L. Shakhnin, S. M. Sukharzhevsky, A. A. Komlev, N. V. Vorob’ev-Desyatovskii, A. Pichugina

Cyanidation of gold ore results in formation not only of Na[Au(CN)2], but also cyanometallate complexes of some transition metals. During subsequent gold extraction from such solutions and pulps, using activated carbons (??), a number of problems arise. An effective solution of the problem is not possible without detailed knowledge of the interaction mechanism of transition metals cyanide complexes with AC particles. The chemical properties of AC particles and graphene, saturated with [?u(CN)n](n-1)- (n=2, 3), were studied by XPS, ESR, SQUID, and DFT. The obtained results were compared with the data on AC adsorption of anionic form of Ag(I), Au(I), Cd(II), Hg(II), Cr(III), Fe(II), Fe(III), Co(III), Rh(III), Ni(II), Pd(II), Pt(II) and Pt(IV) cyanide complexes. The adsorption of [?u(CN)n](n-1)- (n=2, 3) on AC from aqueous solutions in air is accompanied with oxidation of ?u(I) atoms. Besides, Cu(II) and Cu(III) compounds were found on AC surface. Quantum-chemical calculations confirmed the possibility of formation of Cu(I) complex with carbene-like sites of AC. The reactions of [?u(CN)n](n-1)- (n=2, 3) complexes and aromatic carbenes and their cation-radical were theoretically studied at DFT PBE level to obtain the information on adsorption of cyanometallate complexes on AC. Carbenes with different fragments were regarded as a model of activated carbons, which have free edge sites with paired o and n electrons. It was shown that [Cu(CN)2]- bounds firmly with triplet carbene, if one Cu-CN bond breaks. The dissociation process occurs through a multi-step spin-crossing mechanism to reduce total spin multiplicity of the metal-carbene complex. The behavior of transition element complexes in contact with AC in aqueous solutions is determined by the following characteristics: geometrical structure of ionic complexes; nature of ligands bonded to the central atom; concentration of reactive oxygen species in solution and its pH; nature of binding sites of AC.

Jan 1, 2018

By S. Nakamura, K. Fujiwara, S. Hirosawa, S. Tsukamoto, Y. Koshino, Y. Aruga

"In this study, hardness test, differential scanning calorimetry(DSC)and transmission electron micros copy were carried out to investigate the age-hardening behavior of Al-Mg-Si alloy with a Mg+Si concentration of 1.5mass%, and a Mg/Si ratio of 1.0. Pre-aging treatment was conducted for the solution-treated and then water-quenched specimen at 100, 80, 60, 40, 20 (natural aging), 0 and -20°C for 20min or 5h, followed by artificial aging at 170°C for 20min. It was found that when pre-aging time is prolonged from 20min to 5h, the bake-hardening response is deteriorated irrespective of the pre-aging temperature. In particular, the specimens subjected to pre-aging at 20-40°C for 5 h hardly increased the hardness with the subsequent artificial aging. From the results of DSC measurement, it was suggested that as pre-aging temperature is lowered, the amount of solute clusters formed during pre-aging, i.e. Mg-Si clusters and Si-rich clusters, is decreased, but the ratio of Si-rich clusters is increased, resulting in the deteriorated bake-hardening response.INTRODUCTIONIn recent years, Al-Mg-Si alloys have been widely used forautomotive body panels due to their excellent characteristics such as high strength-to-weight ratio and good formability. Their strength is increased not only by artificial aging during paint-bake treatment; i.e. “bake-hardening”, but also when kept at room temperature(RT);i.e. “natural aging”, in association with the suppressed bake-hardening response. Such a “negative effect of two-step aging” has been a serious problem because Al-Mg-Si alloy coils are unavoidably maintained at RT in the manufacturing process of body panels; e.g. shipping and storage. However, it was reported that pre-aging above 70°C before the two-step aging can restore the bake-hardening response, and such an improvement is related to the formation of solute clusters(Sato, 2006; Abidet al., 2010; Takaki et al., 2014; Zandbergen et al., 2015). From the comprehensive analysis by three-dimensional atom probe (Aruga et al., 2014 and 2015), it is believed that Mg-Si clusters formed during pre-aging transform into the strengtheningß"" phase, whereas Si-rich clusters formed during pre-aging act as a detrimental precursor of ß""phase. In this study, it was aimed to investigate the effect of pre-aging conditions, especially pre-aging temperature and time, on the formation of solute clusters during pre-aging, in order to elucidate the mechanism of the age-hardening behavior of an Al-Mg-Si alloy."

Jan 1, 2018