Search Documents

By Jiachen Wang, Nan Wang, Yang Li

The energy structure and consumption ratio in China determine the practical demand for the collaborative mining of coal and co-associated resources. The multi-layer mining of coal, uranium, coalbed methane, and oil and gas co-associated resources, represented by the Ordos Basin, Junggar Basin, and Tarim Basin, faces numerous challenges. Additionally, coal has been found to coexist with various mineral resources in 33 coal-bearing basins worldwide. The scientific issues related to the multi-layer development of coal related co-associated resources urgently need to be addressed. This paper discusses the unique challenges and potential solutions in the multi-layer development of coal-related co-associated resources. The challenges include large extraction space, high mining intensity, intense overburden movement, rapid surface subsidence, and severe overburden damage due to repeated mining disturbances. Proposed solutions include the establishment of a correlation mechanism between multi-layer mining and the carrying capacity of the overburden environment, analysis of the impact characteristics of multiple field couplings, and exploration of their superposition evolution laws. The paper also proposes the development of a comprehensive evaluation and prediction system for overburden environmental capacity loss, a global sensitivity analysis model for overburden environmental capacity, and an intelligent identification and early warning system based on multi-source information fusion. These solutions aim to achieve scientific and precise mining with minimal overburden environmental capacity loss. And the multi-layer development of coal-related co-associated resources is a complex task that requires a multidisciplinary approach and innovative solutions, and further research is needed to validate these strategies and explore new methods and technologies for efficient and sustainable extraction.

Jun 25, 2024

By Peter Zhang, Daniel Su, Berk Tulu, Bo Hyun Kim, Zoheir Khademian

Over 2,000 shale gas wells have been drilled in the Pittsburgh Seam longwall reserves. As longwall panels are laid out, some of these shale gas wells must be located in longwall chain pillars. With longwall mining on both sides and the constraint of chain pillar size, gas well in chain pillars are subjected to longwall-induced ground movements and stresses, which could induce deformations in gas well casings Casing deformations are associated with several factors such as overburden geology, surface topography, setback distance, and casing construction. Overburden geology is one important factor that largely determines the locations and levels of deformations in gas well casings Previous NIOSH gas well research has found that casing deformations above the coal seam horizon are smaller under deep cover than unde shallow cover and that casing deformations could occur at the coal seam horizon under deep cover. Recent mine-by cases have provided more insights into the locations and amount of longwall-induced casing deformations as well as the potential occurrence of a large casing deformation at the coal seam horizon. This paper presents three recent mine-by cases with shale gas wells in the chain pillars between two adjacent longwall panels under different overburden depths. Casing deformations were measured by multi-finger caliper surveys and predicted with numerical modeling. With the established numerical model, the effect of overburden depth was further analyzed to investigate the potential occurrence of a large casing deformation at the coal seam horizon under deep cover. These mine-by cases not only provide a general demonstration of how overburden depths can affect longwall-induced stresses and deformations but also give a good indication about the level of casing deformations that could occur under different overburden depths. The study concludes that (1) casing deformations reduce with increase of overburden depths at the gas well; (2) a cementing alternative with production casing uncemented is an effective means to eliminate production casing deformations; and (3) large plastic casing deformation could occur in the production casing at the coat seam horizon under deep cover. The experience and knowledge gained from these mine-by cases would help longwall operators and gaza companies to take appropriate measures to minimize the influence of longwall mining in shale gas wells in chain pillars.

Jun 25, 2024

By Kevin Andrews, Zach Agioutantis

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By Ke Yang, Kai Zhang, Xiaolou Chi, Xiangyang Zhang, Yingming Li

Based on the research background of 1303 working face return air roadway in Jinyuan Zhaoxian Mine, Shaanxi Province, a method of determining the reasonable spacing of boreholes is proposed based on the stress transfer degree of coal above and between boreholes, combined with the law of plastic zone and energy evolution by theoretical analysis and numerical simulation. After drilling pressure relief, the average daily energy of microseismic events decreased by 70%, and those with microseismic energy greater than 104 J decreased by 99.2%. The research has a strong guiding significance and research value for determining the reasonable distance of borehole pressure relief.

Jun 25, 2024

By Bo Hyun Kim, Mark K. Larson

Although techniques and practices of mining are highly advanced, coal pillar bursts or bumps continue to occur. Many uncertainties remain because of the highly anisotropic characteristics of coal seams that are associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous efforts are required to better understand the catastrophic failure mechanisms in coal mines. In this study, 3DEC modeling in conjunction with the Discrete Fracture Networks (DFNs) technique was performed to better understand the true anisotropic behavior of the specimens acquired from a bump-prone underground coal mine. The spatial characteristics of the dis- continuities (i.e., cleats and bedding planes) as input data for the 3DEC model are estimated based on the results of the laboratory tests and field observations. The DFNs explicitly generated the coal seam that was poorly or well cleated, indicating the different spacing between cleat apertures using the probability distribution functions for fracture density (or frequency) and size. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) are also considered by Monte Carlo simulations. Simulation results of laboratory tests using the 3DEC model and DFNs technique agreed well with the results of the laboratory tests. These calibrated results can be used as we seek to evaluate bump risk by modeling at field scale.

Jun 25, 2024

By Hamid Maleki

Rock mechanics models are “data-limited,” i.e., one seldom knows enough about a rock mass to use computational models unambiguously. Statistical methods, however, are capable of being applied where there are good data but a limited understanding of certain natural phenomena, such as the creep of rock salt or elevated risk domains associated with violent failure of strata commonly referred to as coal bumps and coal bursts. Important to these evaluations are (1) having statistically valid data collected consistently and (2) incorporation of analytical calculations for quantifying geologic, mining and particularly geotechnical variables. By combining the strength of the statistical and analytical models, an improved “hybrid” model is created and utilized. To demonstrate the use of hybrid statistical-analytical techniques in rock mechanics problems, three case studies are used. The first case study involves a historic examination of a nuclear waste repository in rock salt, where mathematical models are built using excavation con- vergence data to identify significant variables and estimate future deformation and stability. This case study uses the convergence rate at up to 121 locations of different ages and geometries using monitoring data over the facilities' footprint excavated through 1998. The second case study focuses on ongoing analysis of coal burst mechanics and associated factors. Within the last three decades, a hybrid statistical-analytical methodology has been applied for identifying significant factors affecting coal bursts. This final hybrid model utilizes data from 30 case studies from Utah, Colorado, Kentucky, and other Eastern U.S. mines providing predictive capability for the entire United States coal fields. The last case study is the assessment of Castlegate Sandstone escarpment stability using historic data collected over 17,000-ft of sandstone escarpment exposure in the vicinity of longwall operations in Utah. Results from all three case studies are used for demonstrating the utility of the method in solving ground control problems.

Jun 25, 2024

By Richard Campbell, MEHMET KIZIL, Ismet Canbulat, Serkan Saydam

The design and effectiveness of ground consolidation to regain stability of longwall faces vary widely and are often based predominantly on-site precedence or what were considered successful applications at other sites in similar situations. Little is known regarding product migration characteristics or change in rockmass conditions as a result of the application of consolidation chemicals. This paper presents the in-situ testing rationale designed and implemented recently across several longwall operations in the Bowen Basin, Queensland, Australia to provide quantitative measurement of the actual zone of influence of various resin injection products. Product migra- tion was physically measured by monitoring the change in rockmass temperature as a result of the exothermic chemical reaction of the various strata consolidation chemicals used. In conjunction with strata coring and Lugeon transmissivity testing pre- and post-injection to characterise the improvement in rockmass conditions due to consolidation product injection. The results of the testing programme, migration measurements, and rockmass assessment are presented, along with a discussion on how site- based Rock Mechanics Engineers can incorporate the data into the design of strata consolidation plans.

Jun 25, 2024

By Matthew Holden, Jason Emery, Matthew Benjamin, Peter Craig

Over the last 25 years, through adversity and a growing level of risk mitigation, Australian Longwall mines have been using higher and higher capacity cable bolts for secondary support. A recent survey revealed 85% of Australian longwall cable bolts are a 70 tonne capacity pre-tensioned hollow post groutable system. Mines avoiding pumping cementitious grouts are sometimes using pre-tensioned resin encapsulated solid cable bolts of over 90 tonne capacity. Results from various industry and University research has led to manufacturer's fine tuning the construction of their cable bolts. A review of this research explains how smooth wire construction is now dominant. Aggressive shear has also led to some mines using 8 tonnes pre-tension instead of the previous common 20 tonnes pre-tension. Lower pre-tension acceptance is now leading to a greater use of threaded cable bolt end fittings, these are tensioned to 8 tonne using the drill motor torque. A recent development is the TEX cable bolt, a slim line threaded end fitting that fits with the drill hole like a standard rock bolt. This cable is being installed at the coal face as primary support off bolter-miners. The laboratory and in-situ testing of the TEX cable is presented. In a bid to improve gateroad development rates and ground support in the last several years, a 100 tonne tensile capacity Goliath cable system was developed. The latest development in resin anchored solid cables is a 110 tonne capacity cable bolt, with laboratory and in-situ testing results presented.

Jun 25, 2024

By S. E. Phillipson

Four massive pillar collapses in limestone mines, and one in a marble mine, occurred between 2011 and 2021 in benched areas at the Appalachian physiographic province. We characterized the rock mass at 43 limestone mines using the Geological Strength Index and, by plotting the results on a physiographic relief map, determined that GSI values between 55 and 70 preferentially occur in the Appalachian and Ouachita Mountains, which were subject to deformation during the Ouachita and Alleghanian Orogenies. Limestone mines located in formations of similar age in the Interior Plains, where deformation was less developed, are characterized by Geological Strength Index values over 80. We present the results of pillar strength calculations that incorporate the Geological Strength Index from mines that experienced massive collapse, as well as from mines with benched areas that did not collapse, to demonstrate the negative effect that a jointed rock mass has on pillar stability. We suggest that pillar designs, particularly those in which benching will be incorporated, should include allowance for rock mass quality. Because of the preferential dominance of lower GSI values in the Appalachians, we further suggest that pillar designs in this environment may require additional engineering assessment, especially where benching is intended. Lower GSI values may often translate into greater overbreak, which results in loss of pillar volume, corresponding wider back spans, and a decreased width-to-height ratio.

Jun 25, 2024

By Thomas Fiest, Helmut Wannenmacher, Wulf Schubert, Manuel Entfellner

Mining and tunneling in so-called “squeezing ground conditions” at high in-situ stress can result in substantial and enduring ground deformations. The magnitude of deformations is closely tied to the applied excavation- and support concept, though typically, they can reach tens of centimeters. The yielding principle is based on the idea, that the need for support capacity decreases as deformation increases. To enable controlled ground deformation and safe working conditions, yielding elements as a part of the shotcrete lining are implemented. These types of elements avoid an overstressing of the shotcrete lining. During the deformation process, the support pressure of the yielding elements and lining increases, thus stabilizing the ground. Furthermore, long-term creep deformations of the rock mass can be absorbed with such a system. This economic support technique represents the state-of-the-art infrastructure tunneling practice in squeezing ground condition. A novel yielding element of High-Strength Expanded Polystyrene (HS-EPS) was invented, which overcomes existing systems’ drawbacks. This innovative system is lightweight and allows for safe and rapid installation. Furthermore, the modular setup of the element enables an easy on-site adaption to react to in-situ deformation patterns and changing ground conditions. Recent experiences from applications in Alpine base tunnels in squeezing ground are presented.

Jun 25, 2024

By Yuting Xue, Khaled Mohamed

Rib control is a critical component of underground coal mining operations, and comprehensive rib support design is essential for ensuring the safety of miners. However, there is currently no standardized approach for rib support design in the United States. To tackle this issue, the National Institute for Occupational Safety and Health (NIOSH) has developed a standalone application, Design of Rib Support (DORS), for rib stability assessment and rib support design under development load. The rib support design in DORS starts with the rib support density, which is determined from the unsupported rib factor of safety (RibFOS). The relationship between rib support density and unsupported RibFOS was obtained from the collected field data. The objective of this research is to validate DORS rib support design by analyzing the extent to which the proposed design capability was utilized to support the coal ribs using numerical simulations. A series of numerical models with varying overburden depth and rib height were built and the ribs were supported with the DORS-recommended rib support design. The bolt load was analyzed under different conditions and the results show that bolt load varies with the overburden depth, the location of the bolt and bolt length. The load in the bolt(s) increases with the reduction in unsupported RibFOS. The bolt(s) start to yield when the unsupported RibFOS falls below a threshold value of 0.8 and secondary support is necessary.

Jun 25, 2024

By Lon Santis, Gregory M. Rumbaugh, Christopher Mark

This paper examines the relevant theory, experience, and past practices relating to development mining near gas or oil wells. It addresses setback distance for both coal and stone room-and-pillar mining. This study also involved a review of accident reports involving well interceptions and downhole well surveys. It provides technical considerations for decisions regarding safe setback distances for development mining throughout the United States. The study’s scope is limited to mining near active or inactive (i.e., non-producing, abandoned or inadequately plugged) wells with known surface locations.

Jun 25, 2024

By Bob Munz, Ry Stone

To facilitate the installation of the longwall equipment for each extraction panel, West Elk mine develops set-up room roadways that are between 26.5 and 30.5 feet wide. Historically at the mine, the set-up room roadways have been driven in a single 20-foot-wide pass, then incrementally widened to the required width during installation of the longwall shields. The first pass roof is supported with a generic roof support plan consisting of partially encapsulated roof bolts and point-anchored cables. This ground support plan was utilized regardless of the geotechnical conditions encountered in the roadways or consideration of the required stand-up time of the roadway before the longwall shields were installed. This "blanket" approach tends to result in over-conservative or inappropriate roof support designs, particularly in changing geotechnical environments. Guided by the desire to optimize the ground support plans and increase mining efficiency for future set-up rooms, the West Elk mine and Agapito Associates, Inc. have developed and implemented a strata management program. Strata management, as a formal and structured process, allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a con- trolled manner (Thomas 2007). To arrive at adequate site-specific ground support plans for the set-up rooms at the mine, several struc- tured processes were utilized. Firstly, the geotechnical environment was characterized by examining the roof lithology and geomechanical properties from nearby rock core obtained from exploration boreholes. To increase both mining efficiency and continuity, and to achieve longer stand-up times before the longwall shields are installed, a multi-pass approach was implemented into the design. During mining, the geotechnical conditions of the roadway are mapped, and the roof is strategically surveyed with a borescope. This process was used to ensure that the encountered ground behavior was in alignment with the design standards used for the roof support design. To support this process with measured data, roof extensometers were strategically installed throughout the roadway. This data was used to monitor the magnitude of roof displacement at various horizons and record displacement rates up until the longwall shields were installed. Lastly, a Trigger Action Response Plan (TARP) was used during mining to cater for any unforeseen changes in ground conditions that would warrant additional con- trols such as increased monitoring or the installation of additional ground support. This paper presents two case histories at the mine where the above strata management approach was implemented to arrive at a site-specific ground support plan. The main changes to the mine's ground control plan included a multi-pass mining approach, the utilization of fully encapsulated roof bolts, and the transition to a stiffer roof support system. The geotechnical mapping, the roof borescope results, and the roof extensometer data will be presented to demonstrate the effectiveness of the ground support system up until the longwall shields were installed in both presented cases.

Jun 25, 2024

By Quansheng Li

Large-scale coal mining will cause environmental problems such as aquifer damage, land excavation and occupation, soil erosion, vegetation damage, and regional landscape damage. The existing coal mine environmental restoration technology is relatively simple, and there is a lack of systematic research on environmental total factors. Based on the mechanism of coal mining damage and the laws of environmental natural succession, the concept of “coal environmental protection mining” is proposed, which combines damage reduction mining and environmental element system restoration. In accordance with the environmental protection principle of “source protection, process damage reduction, and systematic restoration,” a technical system of “coal environmental protection mining” is constructed for the two types of mining damage scenarios: underground mining and open-pit mining. In view of the damage characteristics of underground mining, source environmental protection technology based on optimization of mining process parameters, stability maintenance and damage reduction technology for overlying rock bearing arch shell structure, zoning and time-sharing treatment of surface cracks, and direct drainage irrigation technology for mine water have developed. In accordance with the damage characteristics caused by open-pit mining, land-saving and source reduction damage technology, near-natural stratigraphic reconstruction, topsoil improvement, and environmental storage and utilization technologies for seasonal precipitation have developed. By applying the technology in this paper, the maximum surface settlement value of 12401 working face in Shangwan coal mine was relatively reduced by 25%, the surface cracks have been adjusted from step-type cracks to dynamic small cracks, and since the technical implementation of the Shendong mining area in 2010, the vegetation coverage has increased loss and crushing decreased by 0.06 km2 every year, the environmental restoration period of the dump site was advanced by more than one year, and the vegetation coverage rate increased by 41.78% compared with the background value in the semi-arid area of the victory open-pit coal mine demonstration area. A surface reservoir with a water storage capacity of 400,000 cubic meters has been built, and the seasonal and graded utilization of mine water has been realized. An underground reservoir with a water storage capacity of 1.22 million square meters has been built in the Baorixiler open-pit coal mine.

Jun 25, 2024

By Yuting Xue, Xin Li, Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Mindi Ruan

Most coal mine roofs in the Appalachian region consist of laminated shale, which is prone to brittle failure. Accurate modeling of shale roofs is vital for studying cutter failures of these shale roofs, and ordinary and formational bedding planes play a significant role in the response off the shale roof to mining-induced stresses. This paper presents a robust method for constructing three-dimensional shale roof models using limited borehole cores and leveraging image processing techniques. The approach begins with image extraction from shale cores. Then, we extract the portions that feature the core and employ image-stitching techniques to merge them seamlessly. Once the images are stitched, they are duplicated horizontally and merged to create a cross-sectional plane image representing a shale roof. This roof cross-sectional plane image serves as an input to our proprietary Digital Image Processing (DIP) algorithm, which is adept at extracting ordinary bedding planes (interfaces that represent color transitions between a single shale unit). The extraction process involves transforming discrete core points (ordinary bedding plane pixels) into continuous lines representing ordinary bedding planes. Finally, extending this method into the third dimension, the model is further extrapolated to form a comprehensive three-dimensional shale roof. Through this process, the geometry information of ordinary bedding planes can be extracted for each type of shale in cores, including sandy shale, gray shale, dark shale, etc. This work bridges the gap between limited core data and comprehensive 3D geological modeling, offering valuable insights into identifying and quantifying the variations in different shale roof geologies.

Jun 25, 2024

By Morgan M. Sears

The LaModel program is widely used to calculate stresses and displacements on thin tabular deposits, particularly when multiple seams or complex mining geometry is encountered. The program itself allows the user to create multiple mining steps to show a progressive sequence of mining. However, LaModel considers each individual step as an independent steady-state condition, and any previous loading conditions of the materials are not tracked. It also does not consider any sort of dynamic stress change during the mining process. In certain circumstances, especially in multiple-seam situations, modeling a scenario of the seam of interest without considering the previous mining sequence in the off seams can potentially lead to inaccurate results. The primary objective of this paper is to present a situation where a potentially dynamic, unstable mining condition was encountered. It was not evident until the previous loading conditions in the off seams and the impact of dynamic stress changes in the active seam were considered. It is important to make the mining community aware of these potential modeling scenarios where the path-dependent nature of the mining sequence is of key importance. This paper presents a case history where room-and-pillar retreat mining was being conducted in a relatively deep cover stress regime where multiple seam interactions were present from both undermining and overmining. Mining in the active seam was being conducted with roomand- pillar mining techniques consisting of a series of parallel production panels being successively developed and retreat mined along a set of Mains. In this situation, the traditional global LaModel analysis without any path-dependent adjustments did not fully identify the area of poor conditions that were encountered. This paper explores the impacts of mining in the active seam on the lower seam which, in turn, has a negative impact on the active seam. This provided a solid foundation for the subsequent analysis of the three seams simultaneously. Based on the calibrated model, it is likely that retreat mining in the active seam resulted in increased stresses in the underlying seam that conceivably resulted in additional convergence and, most likely, additionally convergence of the pillars under the panel being developed. This in turn could have caused active subsid- The LaModel program is extremely useful for analyzing multiple-seam mining scenarios. As multiple-seam situations become even more prevalent, the potential for encountering a path-dependent mining scenario also increases. To successfully model path-dependent mining scenarios, the ground control engineer will be required to make sound judgments on the condition of pillars in sub-adjacent seams. These engineering judgments should be based not only on the current state of stress, but also on any prior or future states of stress. This means considering the stresses from over or undermining as well as stresses applied to the sub-adjacent seams from actively mining the seam of interest.

Jun 25, 2024

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By Timothy Batchler, Khaled Mohamed, Morgan Sears

The National Institute for Occupational Safety and Health (NIOSH) initiated a testing program to assess the effects of lateral loading on various standing supports used in underground coal mines. This study is not intended to endorse a particular type of standing supports nor to provide a comparison between different types of standing supports. This paper aims to measure the lateral loading capacity of two types of standing supports and evaluate how it affects their vertical loading capacity and yielding mechanisms. The study utilizes the Mine Roof Simulator (MRS) at NIOSH Pittsburgh. Type-1 support is characterized by telescopic tubes made from ASTM A-513 steel with a specified locking mechanism, and Type-2 support comprises a single component constructed from ASTM A500 Welded Grade C pipe. Vertical load tests were carried out to assess the designed performance of Type-1 and Type-2 props. Type-1 props demonstrated a "constant yielding" behavior, achieving an ultimate capacity of up to 140 kips. Type-2 props showed a "load shedding" behavior, reaching peak verti- cal loads of up to 191 kips. Buckling analysis revealed that Type-1 props were not designed to buckle, and Type-2 props failed due to buck- ling rather than material yielding. Under vertical pre-loading, lateral loading tests showed that Type-1 props can withstand about 9 kips, and Type-2 props can withstand about 10.79 kips of lateral load. This represents roughly 6% of their vertical loading capacities. Testing props under lateral loads in addition to their intended vertical loads showed that the lateral loads could influence their loading mechanisms. Type-1 props did not exhibit the expected "constant yielding" behavior under lateral load but instead showed "load shedding" decreasing their rated vertical capacity by 70%. At high vertical pre-loading, Type-2 props demonstrated "constant yielding" behavior instead of the anticipated "load shedding," leading to a 60% reduction in their rated vertical capacity. These findings provide valuable insights into the behavior of these props under different loading conditions, aiding in their efficient use and design in underground mining operations.

Jun 25, 2024

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024

By Alim Elibol, Rosbel Jimenez, Mustafa Can Suner, Deniz Tuncay, Zach Agioutantis

LaModel is a displacement-discontinuity variation of the boundary element method, which is utilized to analyze the displacement and stress in flat-lying, tabular orebodies. In coal mining, the accuracy and reliability of LaModel are proven with the utilization of the Mark- Bieniawski coal pillar strength and the stress gradient formula with proposed methodologies. However, the application of LaModel is limited to coal mines due to the default coal pillar strength properties. Recently, the stress gradient functions have been established and used to derive concentric rings of zones to simulate stone mine pillar yielding in LaModel. Also, to gain a robust understanding of the brittle failure mechanism and its effect on pillar strength, an S-Shaped failure envelope, where rock mass' cohesive and frictional strength components mobilize as a function of confinement (e.g., minimum principal stress), has been implemented into FLAC3D software. Therefore, by employing brittle failure criteria, the pillar strength stages at various width-to-height ratios and different pillar dimensions are estimated for four benching stages. The estimated pillar strengths and stress gradients for benching conditions are then used to calibrate LaModel in-seam material properties and compare stresses computed by LaModel and FLAC3D. Consequently, this study aims to increase the safety measures in the stone mining industry by implementing the practical use of LaModel for underground stone mines' initial development to various stages of bench mining.

Jun 25, 2024