Search Documents

By T. Tsurata

The accumulation of thorium and/or uranium by various microorganisms from a solution containing thorium and/or uranium at pH 3.5 was examined. Among the species tested, a high accumulation ability for thorium was exhibited by strains of gram-positive bacteria, such as Bacillus megaterium, B. subtilis, Micrococcus luteus, Rhodococcus erythropolis, and actinomycetes, such as Streptomyces levoris. On the other hand, though uranium was accumulated in small amounts from the solution containing both elements by all these microorganisms, actinomycetes, such as S. flavoviridis and S. levoris had relatively high uranium accumulation abilities. In these high performance thorium- and uranium- accumulating microorganisms, S.levoris, which accumulated the largest amount of uranium from the solution containing only uranium at pH 3.5, could accumulate about 300 µmol thorium and 133 µmol uranium per gram dry wt. of microbial cells from a solution containing both thorium and uranium at pH 3.5. After this screening, uranium accumulation using microorganisms isolated from uranium mines, among which some strains of bacteria were found to possess an extremely high uranium accumulating ability. The microbial biomass may thus be considered for use as an accumulating agent for the removal and recovery of uranium that may be present in metallurgical effluents, mine tailings, seawater and other sources. Recently, hundreds of micro-organisms existing in uranium deposits located in North America, Australia, and Japan for their ability to accumulate large amounts of uranium, and found some new strains which accumulated large amounts of uranium, such as Lactobacillus and Bacillus sp. from Japanese and Arthrobacter and Bacillus sp. from the United States uranium deposits. These bacterial strains can accumulate about 2500 µmol uranium per gram dry wt. of microbial cells within one hour. These microbial cells can remove uranium from the uranium refining wastewater with a high efficiency. The accumulation of uranium from a solution (pH 5.8) by microorganisms contained Arthrobacter nicotianee, which is a similar strain mentioned above Arthrobacter sp., was examined. Among the 76 strains of 69 species tested (23 bacteria, 20 actinomycetes, 18 fungi, and 15 yeasts), high uranium accumulation ability was exhibited by strains of the bacteria, A. nicotianae, B. subtilis, and M. luteus. A. nicotianae cells, which showed the best performance, could accumulate about 698 mg uranium (2.58 mmol) per gram dry wt. of microbial cells.

Jan 1, 2014

By E Lounejeva, J A Halpin, A Chappaz, D D. Gregory, S Wu, T Lyons, P J. Sack, R R. Large, S W. Bull

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Newly published models suggest that some orogenic and Carlin-style gold deposits formed by the remobilisation of trace elements during interaction with hydrothermal or metamorphic fluids from early sedimentary pyrite that was enriched in Au, As and Te. The released trace elements are transported by the fluids to favourable trap sites where they are deposited. Therefore, early enrichment of Au, As and Te in source rocks (particularly in pyritic black shale) can be crucial to the formation of orogenic and Carlin-style gold deposits.The most important cause of the enrichment of gold and other trace elements in the sedimentary basins has been examined in this study to determine which basins are the most prospective for the development of orogenic gold deposits. An important influence for Au and other associated trace element accumulation in sedimentary pyrite is the temporal variation of trace element content in the oceans, as revealed by a database of over 1400 analyses of pyrite from black shale through geologic time. It is inferred that sediments coeval with those where sedimentary pyrite is enriched in Au and associated trace elements are more likely to be source rocks of orogenic and Carlin-style gold deposits.Factor analysis of the trace element content of pyrite through geologic time was conducted to investigate the multivariate relationships amongst trace elements and how these chemical factors explain the uptake of trace elements. One important factor includes Te, Au, Pb and Bi content. The incorporation of these large cations into pyrite is enhanced by As3+ substituting for Fe in pyrite lattice. The As3+ ion occurs in relatively oxidised environments and, thus, it is expected that shales deposited in non-euxinic waters are better source rocks for orogenic gold deposits.The examination of both the time in which the sediments were deposited and the redox conditions of the basin, and the ocean more broadly, can be used as a guide to approximate the extent of a basin’s fertility. To illustrate the use of this exploration tool, examples from the unmineralised Jet Rock Formation (UK) and the mineralised Castlemaine Group (Bendigo, Australia) are presented in this paper.CITATION:Gregory, D D, Large, R R, Halpin, J A, Lounejeva, E, Wu, S, Bull, S W, Sack, P J, Lyons, T and Chappaz, A, 2015. Accumulation of trace elements into black shale – how to identify a viable source rock for orogenic and Carlin-style gold deposits , in Proceedings PACRIM 2015 Congress, pp 59–64 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Little faith can be placed in a coal resource estimate without a clear understanding of the estimate's accuracy. Different types of coal resource estimates require different levels of accuracy. Prospecting surveys typically are done with widely spaced boreholes, while a much higher level of accuracy is required for mine design. Either way, a measure of the accuracy clearly indicates the level of confidence that can be placed in the results of the estimate. Geographic information systems (GIs) are becoming a commonly used tool for resource estimation because they not only provide a database management platform but also the graphical capabilities to visualize resource characteristics. interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at multiple locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 2000

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

By M. Karmis, C. Haycocks

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

A nuclear technique utilising the gamma-ray resonance scattering process is used at Isa Mine for the determination of copper in drill core and bulk mineral samples. The Copper Bulk Analyser (CBA) provides quick and accurate non-destructive copper analysis of drill core at costs two to three times cheaper than conventional chemical techniques.The almost immediate availability of sample results enhances the efficiency of the mine geologist in the duties of grade control, design of diamond drilling programmes, and input to planning. The unit has proven to be a reliable and accurate production tool requiring a minimum of technical support.

Jan 1, 1990

By Carson Sharp Beltch

The determination of aqueous cyanide is accomplished by either detection in the sample as collected or by removal of the cyanide of the collected sample, followed by detection. The direct determination of the cyanide content of a solution can only be used in the simplest of systems, since many interferences can result in errors. Thus the most widely used method for total cyanide determination involve the reflux distillation of the sample using heat, acid and vacuum or air flow. The basic theory underlying this analytical approach is that by reducing the pH, the quality of molecular hydrogen cyanide will be in- creased and can be removed from the solution by elevating the temperature. The hydrogen cyanide is then collected in a caustic solution and analyzed. The general approach of removing the cyanide from the sample by distillation represented a major advance in this area of analytical chemistry. It enabled the determination of cyanide in many additional types of samples. When it became apparent that the tightly bonded cyanide complexes were not being detected by this approach, many methods fox complex ion destruction were proposed. These methods usually involved low pH adjustment with oxidizing mineral acids, coupled with the catalytic decomposition of the tightly hound complexes. All off the complexes except the strongest could he broken by these methods. The catalytic reflux distillation step has been found to have some negative aspects, since many materials that can be distilled with hydrogen cyanide will interfere with the color development step and result in a false positive reading.

Jan 1, 1981

By Richard L. Bullock

Believe it or not, mine evaluation and feasibility studies are as old as the industry itself. In the first recorded writing on mining by Agricola (1556), he gave several clues as what to look for in evaluating a mine, to determine if it was economically feasible. Below is the guidance from Agricola, with my interpretation of what he would include today. Now a miner, before he begins to mine the orebodies must consider seven things, namely: ? The situation (the geography/topography). ? The conditions (the geologic/mineralogic and mining conditions). ? The water (availability, hydrology and ownership). ? The roads (plus the railroads, power lines, all other infrastructure). ? The climate (the weather-rainfall/environment). ? The right of ownership (the land and legal entitlement). ? The neighbors (the social environmental concerns of the area). It is amazing how much of his guidance has not changed in 455 years. Yet Agricola gives no guidance on determining the correct cost, or determining the correct commodity pricing. But he does give a few words of caution on the related ethics involved on buying mineral properties: ?A prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him.? Three hundred years later (1866), to further amplify this point, in the most famous thing that Mark Twain never said, as an introduction to a lecturer to an audience of gold-miners at Red Dog, CA, the famed author/humorist allegedly described a mine as ?a hole in the ground owned by a liar? (Farrar & Rinehart, 1935). So, one might conclude that between these two dates, the mining industry did little to improve its reputation. Unfortunately, since Mark Twain allegedly made those remarks, we have not done near enough to gain accountability for the mineral industry.

Jan 1, 2011

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By Williams DJ, Battino S

The rapid crushing technique for the measurement of gas content of coal consists of accelerating the rate of gas desorption from coal by crushing. This technique allows the determination of gas content in the space of hours rather than days or weeks as required for the traditional slow desorption technique. The crushing technique is used particularly when gas content determinations are urgently required for mine safety purposes. The method is now routinely used in underground coal mines of NSW and to a lesser extent in QLD. Despite the rapidity and efficiency of this method, concerns have been raised upon the reliability of the method to deliver accurate results. Experience in Australia has shown that there is in fact some discrepancy in results between gas laboratories using the rapid crush technique. The development of rapid crushing techniques for seam gas content measurements in Australia and the main causes of variability in the gas content test results were investigated. The gas laboratories participating in the gas content testing were CSIRO Division of Coal and Energy, BHP Technical Services and GeoGas Pty. Ltd.

Jan 1, 1998

By Brad McBain

Agenda ? Accurassay Laboratories and Automation ? History and experience ? Features and benefits of automation in the lab ? Tata Steel Minerals Canada (TSMC) Iron Ore Laboratory ? State-of-the art systems and design ? The integration of fusion systems and XRF units ? Meeting deliverables: quality, reliability, safety

Aug 1, 2013

By M. Dupuis

In the present study, the heat balance of the Hirakud smelter aluminium reduction cell has been accurately assessed using only a surface thermocouple and a pyrometer, As it is well known that using a single linear or quadratic relationship to estimate the heat flux from the measured surface temperature does not provide the accuracy required to close the cell heat balance, this approach was not used in this study, Instead, the fundamental natural convection and radiation heat flux equations were used systematically for each measurement point, Practically, this means that the ambient air temperature and at least one ambient radiative temperature must also be known in addition to the surface temperature for each measurement point. Sometimes, the radiative heat flux could not be accurately estimated using a single ambient radiative temperature, In those cases, a more accurate estimation based on two ambient radiative temperatures and corresponding view factors has been used instead, It turns out that although at least three temperature measurements are required to estimate a single heat flux, it takes a lot less time to make those temperature measurements using a pyrometer than directly measuring the heat flux using an expensive heat flux meter, Furthermore, no loss in accuracy was detected when using this approach as the cell heat balance could be closed within 5%, the level of accuracy typical of cell heat balance assessment using heat flux meter.

Jan 1, 2004

By W. J. Birch, R. Farnfield

All shock-tube based initiation systems have a time lag relating to the propagation velocity of the shock-tube itself. This paper examines the exploitation of this inherent time lag to achieve delay blasting with accuracies approaching that achievable with electronic systems albeit over a much shorter delay range. The system employed consists of a combination of standard shock-tube, plain detonators and various shock-tube branching components. The accuracy of the complete system depends on the scatter in delay time induced by each component. In order to quantify this scatter a series of trials were undertaken to determine the variability for each component. These trials are described along with a detail statistical summary of the data recorded.

Jan 1, 2009

By Maria C. Jaime

Optimization of the rock cutting performance plays a major role in the tunneling operation. For a given set of tool and cutting environment, rock fragments may be chipped away in numerous manners and it is crucial to understand and be able to predict the dynamics at the cutter-rock interface. This paper presents rational and realistic 3D finite element modeling of rock cutting where typical computational issues ?such as contact formulation, appropriate rock material response, mesh distortion, and crack propagation? are overcome. Cutting forces and failure mechanisms in this finite element analysis are successfully validated by laboratory single-cutter scratching tests in sandstone.

Jan 1, 2010

To develop more accurate means of measuring low ventilating air velocities in underground mines to facilitate compliance with ventilation standards. The Approach: A commercially available vane anemometer which produces an electrical, rather than a mechanical, output was coupled to electronic circuitry to produce the Bureau's Digital Low Velocity Anemometer (see photo). [ ] How It Works: The experimental instrument has a vane anemometer head which produces an electrical output signal with a frequency directly proportional to the rotating speed of the vane anemometer shaft. The commercially available ABBIRKO FLOWMASTER anemometer head was used in this instrument. In the signal conditioning circuits the electrical signal from the anemometer is converted into pulses, which are counted during either 3-second or 1-minute intervals, depending on the position of the operator's control switch. (Readout is either "instantaneous" or averaged for a period of one minute.) The number of pulses counted is then translated (integrated and divided by a constant) in the logic circuits to get average speed. Average air velocity in feet per minute is displayed in illuminated digits. (See simplified diagram of circuitry.)

Jan 1, 1975

By Edward P. Larsen

At our annual meeting in St, Louis, Mo. in February 1961, we presented a comprehensive paper (No. 61-B-22) on the subject of "Blending and Handling of Materials for Agglomeration". In that paper you will find a discussion on the difference between "blending" and "mixing". With regard to "blending" we brought out the facts of its usefulness for the preparation o materials in an agglomerated mass to attain controlled chemical and physical uniformity. "Mixing" was discredited as not being useful for the attainment of uniformity of any kind.

Jan 1, 1962

By Carl Pinches

Underground or surface mining is only the first stage in the ore mining process. Once the ore is mined, it is transported to the surface for further processing. Generally, this is done to extract the particular metal or other component of the ore that has commercial value in its purified form. In its raw state, there are typically between 4 and 7 g/t (0.12 and 0.2 oz/st) of valuable material from rock mined. Once on the surface, the ore is crushed and milled in order to obtain smaller rock particles and to expose the minerals that contain the desired metal or component. Mixing the milled ore with water, a process known as ?froth flotation,? can be employed. This technique consists of a series of tanks, or ?cells? through which the process liquid flows. To obtain the maximum recovery, the milling and flotation process will often be repeated a second time. An increase between 100 and 1,000 g/t (2.9 and 29 oz/st) of rock following this stage of the process is typical. Efficient recovery is key to maintaining a profitable mining operation. The measurement and control of the froth flotation process is vital.

Jan 1, 2010

By James Warren Andrews

The values of saturated water vapor pressure from steam tables have been found to be inaccurate for mine ventilation usage because the effect of air on the saturated water vapor was disregarded. Presented here are the newest and most accurate currently available tables from the National Bureau of Standards (NBS). Also included are: (1) a formula for correcting the saturated water vapor pressure for temperature and altitude. (2) a formula for computing unsaturated water vapor pressure, and (3) a formula for air density. Because Systeme International (SI) units are used in the formulas, conversions are given from U. S. conventional units to SI units. The intent of this paper is to show by means of six steps the accurate calculation of mine air density for use on modern computers.

Jan 1, 1989

By M Hedley

Tracking plant and personnel in underground environments provides multiple potential benefits for a mine including increasing safety, better monitoring of production, traffic control, and in the future monitoring and control of autonomous vehicles. The main techniques for wireless tracking are to use radio frequency identification (RFID), signal strength based techniques, and time of arrival (TOA) based techniques. RFID does not provide continuous tracking and signal strength techniques have poor accuracy in the complex radio propagation environment present in mines. TOA based techniques are potentially the most accurate, but most current equipment does not realise the potential of the technique. CSIRO has been developing the wireless ad-hoc system for positioning (WASP) system for wireless tracking in a range of challenging environments including underground mines. WASP has been licensed for sporting applications and has delivered encouraging results in early trials for a surface and an underground mining application. The system utilises a number of ‘anchor nodes’ that are placed at surveyed fixed locations within the mine, and tags attached to plant or personnel to be tracked. The system provides an ad hoc data communication network, thus wired data connections are not required to the anchor nodes. WASP uses transmissions in the 5.8 GHz ISM (instrumentation, scientific and medical) frequency spectrum to perform highly accurate ranging between nodes, hence tracking of tags. The localisation performance of the system depends upon the radio propagation environment, ranging from 0.1 m in low multipath conditions. In this paper we describe the WASP system and provide results of initial testing in an underground mine that shows that the system achieves high ranging accuracy, hence localisation accuracy.

Mar 21, 2011

By John Starkey

"The development of the SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.Previously, it was deemed prudent to select up to 50 t samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5 t sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50 t sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003