Search Documents

By Pratheesh George

Solid state galvanic cell with CaF2 as the electrolyte was employed for determining the thermodynamic properties of Nb-Al binary alloys in the temperature range of 973-1073 K. The activities and activity coefficients of Al in NbAl3 were determined. The experimental procedure and the design and construction of the experimental setup have been also explained in detail. Aluminum activity in NbAl3 increased with increase in temperature and shows a strong negative deviation from ideality. The activities of aluminum in NbAl3 were determined to be 0.0165 and 0.0289 at 973 and 1073 K respectively. The stability of NbAl3 has been compared with other available intermetallic systems.

Jan 1, 2006

By Koji Matsubara, Yoshiaki Iguchi, Shoji Hayashi

Iron ore particles of a limonite iron ore were reduced completely with H2 at 1023K to 1273K in a fluidized bed. Then, at 973K, the formed iron was exposed to HrH2S mixtures (sulfur activity, as=0.5) for 3.6ks and carbidized with CO-H2-H2S· mixtures at 0.1 MPa. During the carbidization, the particles of about 150mg were sampled at every 600s interval. The sampled particles were analyzed by XRD and chemical analysis for C and S to evaluate the content of Fe3C, Fe5C2, Fe and free carbon. The reaction extent is defined as fo=Xfc3C +xFc5c2; x is the molar fraction of Fe in Fe3C. The carbidization curves can be fitted very well to -ln(l-f0)=g(pb T)t; g(p; T) is the carbidization rate, i.e. the carburization rate on the pore surface of reduced iron. The rate is found to be nearly proportional to the specific surface area of reduced iron, a P 0 , which decreases with increasing the reduction temperature. The value of a P 0 does not change by the carbidization and the stability of the iron carbide product in the atmosphere increases with the temperature.

Jan 1, 2000

By B. Balamurugan, D. J. Sellmyer, J. E. Shield, G. C. Hadjipanayis, Damien Le Ror, R. Skomski

"Rare-earth transition-metal (R-TM) alloys show superior permanent magnetic properties in the bulk, but the synthesis and application ofR-TM nanoparticles remains a challenge due to the requirement of high-temperature annealing above about 800 °C for alloy formation and subsequent crystalline ordering. Here we report a single-step method to produce highly ordered R-TM nanoparticles such as YCO5 and SmCO5, without high-temperature thermal annealing by employing a cluster-deposition system, and we investigate their structural and magnetic properties. Nanoparticles of size = 10 nm are monodispersed (s /d ~ 0.15) and have Hc values at T = 300 K of 8.0 and 4.5 kOe for YC05 and SmC05, respectively. Alignment of the easy axes is performed via a field applied to the clusters before deposition. These processing steps are highly desirable to create and assemble R-TM nanoparticle composites for future permanentmagnet applications.IntroductionMagnetic nanoparticles with high magnetocrystalline anisotropies (Ki > 1 MJ/m3) are required for permanent-magnet, recording-media, and other significant applications [1-3]. In this regard, bulk rare-earth transition metal alloys (R-TM) especially RC05 (R = Y and Sm) crystallized in the hexagonal CaCu5-type structure have shown a large Ki = 5 MJ/m3 (YC05) and 22 MJ/m3 (SmCo5) along with an appreciable saturation-magnetic polarization (Js, > 10 kG) and high curie temperatures (Tc > 1000 K) [2]. The challenges in controlling the size, sizedistribution, phase purity and crystalline ordering, however, limit the research on RCo5 nanoparticles [4,5]. The conventional arc-melting technique requires high-temperature annealing for alloy formation and subsequent crystalline ordering, which causes excess growth and thus results in nanocrystalline powders of particles sizes larger than 30 nm [6, 7]. Low-temperature wet-chemical techniques yield SmC05 nanoparticles of sizes smaller than 20 nm [5], but the control of phase purity is challenging due to the presence of surfactants and formation of other secondary phases [8]."

Jan 1, 2012

By W. G. Davenport

This chapter extends our mathematical description of flash smelting to -nitrogen in the flash furnace blast. As in chapters 4 and 5, the discussion is limited to auto thermal smelting (no hydrocarbon combustion). Hydrocarbon combustion is introduced in Chapter 9. Outokumpu flash furnace blast is a mixture of air and industrial oxygen. Most of its N2 originates in the air portion of the blast. A small portion originates as an impurity in the industrial oxygen. The nitrogen entering a flash furnace must always be heated from its input temperature, 298 K in this chapter, to its off gas temperature, -1500 K. Energy must be supplied for this purpose. With auto thermal smelting, the energy is-provided by oxidizing extra Fe-and S.

Jan 1, 2001

By Gang Qi

The solubility of nitrogen in pure molybdenum was measured over the temperature range 2173 to 2473 K and up to one atmosphere (101 kPa) of nitrogen gas pressure. Both thermochemical and kinetic aspects of this phenomenon were considered in this study. The solution of nitrogen in molybdenum may be expressed by the reaction 1/2N2(g) = {N} (Mo,s), for which the standard Gibbs energy is given by the expression {A}G° = 78,500 + 27.36T Joules/g atom N. The formation of molybdenum nitrides, specifically Mo2N, was considered. Attention was also focused on the mechanism of nitrogen solution in molybdenum. Estimates of the diffusivity of nitrogen atoms in solid molybdenum were derived from the kinetic data.

Jan 1, 1991

By Zhongning Shi, Ramana G. Reddy, Min Li, Zhaowen Wang

Electrodeposition of cobalt from cobalt tetrafluoroborate (Co(BF4)2) was investigated using 1- butyl-3-methylimidazolium tetrafluoroborate (BMIMBF4) ionic liquid. The experiments were conducted at 353 K. Chronoamperometry experiments confirm that the electrodeposition of cobalt on tungsten electrode proceeds via three-dimensional instantaneous nucleation with diffusion-controlled growth process. The average diffusion coefficient of Co(II) was found to be 7.5 × 10-8 cm2s-1 at 353 K, which is in good agreement with the estimated value from cyclic voltammetry. The electrochemical deposit was characterized using SEM-EDS and XRD methods. The SEM image shows formation of a dense and compact deposit at - 0.75 V. The EDS and XRD analysis confirm that the obtained deposit is pure cobalt metal.

Jan 1, 2015

By Marcelo B. Mourão

An experimental investigation was carried out to -study the rates of reduction of pellets containing iron oxides by carbon dissolved in liquid iron, at temperatures ranging from 1720 K to 1973 K. Several different pellet types were employed; the materials used in the pellet's manufacture were pure hematite, two kinds of commercial iron ores, and mixtures hematite/silica and hematite/lime: Reaction times were determined employing the constant volume pressure increase technique (CVPI). It has been observed that the reaction rate increases as the temperature and the pellet's specific surface area increases. The reaction rate is also affected by the oxide type: pellets made from commercial ores or from mixtures hematite/silica or hematite/lime show reaction rates lower than those made from pure hematite.

Jan 1, 1996

The viscosity of high magnesium content FeO-Fe3O4-SiO2-CaO-MgO slags at nickel flash smelting conditions was investigated using a commercial rotational viscometer. The studied parameters were compositions of slag and temperature. The viscosity of these slags was measured as a function of CaO, MgO, SiO2, FeO. Fe3O4 and Fe/SiO2 in temperature range from 1473K to 1723K. These slags contained 5.81 to 10.59 pct MgO, 0 to 10.37 pct CaO, 28.21 to 36.21 pct SiO2, 39.40 to 55.42 pct Fe and 1.1 to 1.5 Fe/SiO2.

Jan 1, 1999

By P. T. Velu

Light weight aluminum alloys are the major construction materials for a number of structures in automobile and aerospace industries. Higher cost of production is the key impediment which restricts the usage of these alloys. A new electrochemical process route for the low cost production of aluminum alloys is being investigated, in which alloying elements are obtained from the dissolved compound. In the present investigation, solubility of lithium compound has been determined by measuring the EMF, when it is dissolved in the electrolyte. The solubility of Li2CO3 increased with temperature from 2.95 wt pct at 1063 K to 7.57 wt pct at 1093 K. Activities of the compound in the electrolyte were deduced using Temkin's ideal solution approach.

Jan 1, 1995

By Hideki Yamamoto

A new technology to convert fluoride gas (C2H2F4 ; R-134a) contained in the exhaust gases from semiconductor manufacturing plants and refrigerators directly into a harmless substance have been established, thus, presenting a new concept for the disposal of fluoride gases such as CFCs that are associated with the global warming. Experimental results verify that chemical reactions with metal compounds can take place at substantially lower temperatures of 700- 800K as compared with combustion. treatment temperatures of 1200-1500K. The reaction product is mainly metal fluoride, which chemically is a harmless material. Furthermore, this process is compact, easily controlled, safe and has low running costs. This paper deals with a new chemical reaction method for the harmless disposal of gases effecting the global warming.

Jan 1, 2003

By Hideki Yamamoto

A new technology to convert fluoride gas (C2H2F4 : R-134a) contained in the exhaust gases from semiconductor manufacturing plants and refrigerators directly into a harmless substance have been established, thus, presenting a new concept for the disposal of fluoride gases such as CFCs that are associated with the global warming. Experimental results verify that chemical reactions with metal compounds can take place at substantially lower temperatures of 700- 800K as compared with combustion treatment temperatures of 1200-1500K. The reaction product is mainly metal fluoride, which chemically is a harmless material. Furthermore, this process is compact, easily controlled, safe and has low running costs. This paper deals with a new chemical reaction method for the harmless disposal of gases effecting the global warming.

Jan 1, 2003

By I. Barin

The thermodynamics of cyclone smelting of sulphidic copper ores is described using as example the production of copper matte with 75 wt % Cu. Equilibrium calcualtions and material and energy balances show that an increase in process temperature from 1600 K to 1900 K results in the extensive transfer of minor elements such as As, Sb, Bi, Pb, Zn,.... to the gas phase. A pilot plant for carrying out the cyclone smelting process is described. Calculations of material and heat transfer for the reaction of ZnS show that the smelting reactions of sulphides in the cyclone take place very rapidly at high temperatures. The dissociation of the sulphides with subsequent oxidation reactions in the gas phase plays an important part in. the process and is mainly controlled by heat transfer.

Jan 1, 1983

By Sang Han Son

The vapor pressures of FeCL2 and ZnCL2 in the FeCL2?ZnCL2 system were measured by the transpiration method at 873K and 9I7K, The vapor pressure data were interpreted to indicate the formation of complex ions in the FeCL2?ZnCL2 melts, It is presumed that the complex molecule FeZnCl4 as well as FeCL2 and ZnCL2 exists in the vapors in equilibrium with molten FeCL2-ZnCL2 mixtures, The activities in the FeCL2-ZnCL2 system are shown a negative deviation from Raoult's law. These results suggest the formation of complex ions such as ZnCL14 in molten FeCI2?ZnCL2 mixtures.

Jan 1, 2003

By Sang Han Son

The vapor pressures of FeCI2 and ZnC12 in the FeCl2-ZnCl2 system were measured by the transpiration method at 873K and 917K. The vapor pressure data were interpreted to indicate the formation of complex ions in the FeCl2-ZnCl2 melts. It is presumed that the complex molecule FeZnCl4 as well as FeCI2 and ZnCI2 exists in the vapors in equilibrium with molten FeCl2-ZnCl2 mixtures. The activities in the FeCl2-ZnCI2 system are shown a negative deviation from Raoult's law. These results suggest the formation of complex ions such as ZnCl42- in molten FeCI2-ZnCI2 mixtures.

Jan 1, 2003

By Kelly J. Driscoll

Impure zinc (98.5%) was electrorefined to high purity zinc (99.995%) using a fused salt electrolyte of molar composition 1: 1 : 1 :2 ZnCI2:KCl:NaCl:LiCl with a current efficiency of about 90% at 723 K. A recessed channel electrorefining cell was developed which achieved excellent mixing of both the metal and the electrolyte and by ensuring a very small anode to cathode spacing the voltage drop across the cell was 0.16 V and at a current density of 7kA m-2. The physical characteristics of the cell were observed using a low temperature model which showed the formation of droplets and rivulets which provided mixing. The application of this approach to the refining of other non-ferrous metals is discussed.

Jan 1, 1992

By S. Y. Tan

As continual complementary metal?oxide?semiconductor (CMOS) scaling requirements, metal gate/high-k dielectric/Si gate stacks are expected to replace poly-Si/SiO2/Si gate stacks in the future CMOS sub-45 nm technology node. Hafnium based oxide is a promising candidate to replace SiO2 as a gate dielectric, due to its much higher dielectric constant (high-k) and stability. The key challenges of successfully adopting the high-k dielectric/Si gate stack into advanced CMOS technology mostly come from the interfacial properties. The origins of the electrical and physical characteristics of the dielectric oxide/bulk interface were studied in detail. The leakage current density-voltage (J-V) and capacitance-voltage (C-V) measurement techniques were employed to study the dielectric oxide/Si interface. The effects of the post-deposition annealing (PDA) treatment on the interface charges of dielectric oxides were studied. We found that the PDA can effectively reduce the trapping density and leakage current, and eliminate hysteresis in the C?V curves. Besides, the changes in chemical bonding features at HfO2/Si, HfSiO/Si and HfSiON/Si interfaces due to PDA treatment were evaluated by XPS measurements. The XPS analysis provides a better interpretation of the electrical outcomes. As a result, both HfSiO and HfSiON films have exhibited superior performance in terms of thermal stability and electrical characteristics.

Jan 1, 2010

By O. Ryosuke Suzuki

A new metallurgical process via sulfide is proposed: a sulfide is produced at a high temperature from its metallic oxide using gaseous CS2, and this sulfide is electrochemically reduced to its metallic state using molten salt. This combined process via sulfide is effective to obtain high purity of metallic powder, even if the metal in its oxide is strongly combined with oxygen. For example, it is not easy to reduce stable oxide TiO2, and only Ca can remove oxygen to form α-Ti. However, a fairly large amount of oxygen remains as Ti–O solid solution. Because the solubility of S in Ti is very small, this proposal was examined experimentally both on the conversion of TiO2 to TiS2 and on the successive reduction of TiS2 to Ti. TiO2 powder was exposed to CS2 gas flow at 1073 K, and the conversion to TiS2 was confirmed. TiS2 could be reduced to Ti powder either by calciothermic reduction or electrolysis in a CaCl2 melt. By Ca reduction at 1133 K in CaCl2 melt, sulfur concentration decreased to 0.03 mass%S when the amount greater than twice the stoichiometric calcium amount is added. By electrochemical reduction at 1173 K in CaCl2–CaS melt, S concentration significantly decreased to 0.01 mass% S when four times larger amount of electric charge was supplied.

By Masahiro Hirasawa

"As a fundamental study on pyrometallurgical process that involves recycling steel-making dusts, of which major components are oxides of Zn and Fe, and waste polyvinyl chloride simultaneously ·at. a temperature below 1273 K, the reactions between the mixture of ZnO + Fe20 3 and PVC or the compound ZnFez04 and PVC are investigated in a series of thermogravimetric and small scale reactor experiments under inert atmosphere at below 1273 K. The reaction mechanisms are discussed· on the .basis of the thermogravimetric data. From the results of reactor experiments, it is shown that the chlorination of Zn in the oxides by Cl in PVC, the vaporization of ZnC12, the reduction of iron oxide to metal Fe by C and H in PVC, and, thereby, the separation of Zn and Fe in the oxides take place simultaneously at the temperature ~= 1200 K.IntroductionSteelmaking dusts are metallurgical wastes consisting mainly of oxides of Zn and Fe with smaller amounts of other heavy metal elements, such as Pb. In the recent investigation, [1] the present authors have investigated the fundamental aspects of a potential pyrometallurgical process· of recycling steel-making dust with polyvinyl chloride (PVC) at temperature T < 1273 K under Ar atmosphere. The performance of a similar process, in which HCl in the combustion gas of PVC is used to chlorinate Zn in the EAF dust under oxidizing atmosphere, has been investigated by Tailoka and Fray [2] with fundamental experiments. Figure 1 shows an example of the potential ·diagram of Zrt-Cl-0 and Fe-Cl-0 systems. In the figure, we can find two regions where ZnCl2(g) can be separated from Fe containing compounds. One is ZnCiz-Fe20 3 coexistence region at higher oxygen and chlorine potentials and the other is ZnCl2-Fe coexistence region at lower oxygen and chlorine potentials. The process adopted by Fray and coworkers is aimed mainly at the performance of Zn/Fe separation in the higher oxygen potential region. In the present study, the lower oxygen potential region is focused on."

Jan 1, 2000

By H. Y. Sohn, S. PalDey

"Fine particles of nickel aluminides and Ni4Mo were synthesized by reducing mixtures of, respectively, A1Cl3 + NiC12 and NiC12 + MoC12 vapors with hydrogen. Though thermodynamically favorable, the coreduction of NiC12 and A1Cl3 by H2 to form Ni3Al did not readily happen experimentally. The addition of a small amount of aluminum vapor was needed to initiate the coreduction reaction. The product particles as observed by TEM were very fine but usually agglomerated. The electron diffraction pattern of particles identified NiAl and NiA13 along with Ni3Al and metallic Ni. The content of Ni3Al was maximized at 52 mol% at 1050°C under the partial pressures ofH2, A1Cl3, and NiC12 at 57, 1.4, and 0.5 kPa, respectively. When a mixture of NiC12 + MoC15 was reduced by hydrogen, Ni4Mo particles with some Ni or Mo particles were obtained, the maximum content of Ni4Mo obtained being 93 mol % . The particle size was in the range of 100 to 200 nm. An Ni4Mo coating of 700 nm thickness on an Ni substrate was also prepared.IntroductionThe search for new high-temperature structural materials has stimulated much research on intermetallic compounds. Nickel aluminides have low densities, relatively high melting points, and good high-temperature strength properties. They show an increase, rather than a decrease, in yield strength with increasing temperature (1). Ni4Mo is also of interest as a high-temperature structural material. The major shortcomings of these intermetallics are their inherent brittleness at room temperature when they are in polycrystalline form. For much the same reason, the conventional casting of intermetallics is difficult. Ingot metallurgy and powder metallurgy are two other processing techniques. The first technique is quite energy consuming. In powder metallurgy, the powders of metals and alloys are consolidated in near net shape and then subjected to secondary processing. It would, therefore, be advantageous if intermetallic compounds can be produced in fine powder form from inexpensive raw materials, using less energy."

Jan 1, 1998

By Charles A. Sorrell

Two red muds, two fly ashes, and several aluminosilicate minerals were subjected to direct treatment with concentrated H2SO4 at temperatures of 175°C and below. X-ray analysis showed that virtually all the sulfate reaction products remained in the solid residue because of their low solubilities in x SO Substantial portions of the Al2O3 Fe2O3TiO2, Na2O, and K2O components of the materials reacted to form water soluble sulfates, which were then removed by H2O leaching at 55°C. The solid residue after water leaching consisted largely of amorphous silica and, in lime bearing compounds, CaSO4, The reaction and leaching processes were effective in removing all or nearly all the Al2O3. Fe2O3, TiO2, Na2O, and in lime components in the fly ashes, red muds, china clay, bentonites, the nephelioe fraction of nepheline syenite, and a plaster insulating brick composed of anorthite and mullite. Reaction with potassium feldspar and petalite took place, with formation of alkali aluminum sulfates, but the reaction rates and yields were extremely low. Potassium feldspar can be heated with Na2O and x O in air at 700°C for 24 hours, or with CaO at 1000°C for 24 hours, after which the reaction product kaliophilite, nepheline, and leucite-like phases, prove to be very susceptible to H2SO4, reaction and H2O leaching, providing yields near 100% of the Al2O2 content. An alternative method of H SO treatment consists of heating the sample in a silica tube and passing H2SO4 vapor over it. Preliminary results indicate that this method can be effective in enhancing the kinetics of reaction with the Al O component of potassium feldspar and offer the possibility that formation of Al2 (SO ) Fe2(SO4)3 and TiOSO4 can be accomplished selectively by taking advantage of the fact that the upper stability limits of the respective sulfates in the presence of H2SO4 vapor will be different.

Jan 1, 1982