Search Documents

By Pengcheng Li, Wei-Tong Du, Yu Wang, Gang Wen

Carbon dioxide could be utilized as a weak oxidant and a kind of coolant to oxidize elements, meanwhile, helping control the temperature during the converter vanadium extraction process. However, the optimum content of CO2 and the cooling effect of CO2 at low content have not been reported. In this study, experimental research based on the influence of different CO2 contents from 0% to 25% injected to the vanadium-containing hot metal was carried out, as well as contrast experiments of O2-N2 mixed blowing. The results indicated that the optimum content of CO2 was 15%. Under the optimum condition, the oxidation of [C] was the lowest and the oxidation rate of [V] was 96.9%, while the temperature was also lower than the O2-N2 mixed blowing. This paper provide a potential property for utilizing CO2 during the converter vanadium extraction process.

Jan 1, 2016

By Marcio Toshio Tanaka, Marcelo Breda Mourao, Cyro Takano, Cesar Yuji Narita

"The concerns in questions related to the environmental impact in the steelmaking industries caused mainly on the gas emissions such as the dioxide carbon are due to its raw material such as the coal, a fossil and non renewable resource. The purpose of this paper is to replace from 10% to 50% of the coal used in cokemaking by mixing it with a renewable source (wood charcoal). The powder (- 325 mesh) from both raw materials (coal and wood charcoal) were mixed in order to obtain a briquette that was then heat treated at 1100°C to obtain the biocoke. Results of usual analysis (coke reactivity index, coke strength after reaction and cold crushing strength test) were employed to compare to regular coke briquettes. It was found that biocoke with different amounts of wood charcoal present features enabling it to be used in some ore reductionprocesses.1. IntroductionThe iron and steelmaking industry is a heavy emitter of carbon dioxide; according to the World Steel Association, 6.5% of global emissions of this greenhouse gas is due to the production of ferrous materials [ 1]. This is due to the fact that the fuel and reductant employed in the blast furnace is metallurgical coke, obtained from fossil coal. There are some projects aiming to reduce or even eliminate the emission of fossil GHG in the iron and steelmaking process [2]. Most of them propose the capture and storage of the gas (CCS) [3], a technology not yet proven. Other studies point out that the coke consumption in the blast furnace could be reduced by using high reactivity coke; this could lead to lower temperatures in the thermal reserve zone of the blast furnace and consequently less fuel rate in the furnace.The use of biomass in the iron ore reduction process is known as an environmentally accepted solution, as biomass does not release already fossilized carbon."

Jan 1, 2013

By Aline Maria dos Santos Teixeira, Francisco Manoel dos Santos Garrido, Joao Alves Sampaio, Marta Eloisa Medeiros

"Rocks for crops is a natural practice for soils fertilization which consists on adding rocks to the soil while water decomposes the rock, through chemical weathering, and gradually releases nutrients to the soil solution. This practice can be considered an alternative to the low production of potassium fertilizers in Brazil. In this context, the phonolite rock was characterized in order to evaluate its application as an alternative source of nutrients to the Brazilian agriculture. The phonolite studied is an igneous, volcanic rock with alkaline character that is chemically composed of a high grade of potassium due to the presence of feldspar minerals. In order to quantify the minerals present in the sample, characterization was carried out using several techniques such as X-ray diffraction, X-ray fluorescence and scanning electron microscopy.IntroductionBrazilian soils are generally acidic and nutrient poor due to the tropical climate in which high temperatures and intense rainfall favor a rapid decomposition of the rocks that from the soil. And as agriculture is one of the main bases of the country's economy, large amounts of fertilizer are used to make the soil productive.Although Brazil has large reserves of potassium, the demand for potash fertilizer is higher than the national supply, which makes the country dependent on fertilizer imports, especially in the form of potassium chloride. Thus, we must look for economic alternatives to traditional fertilizer [1].Stonemeal is a natural practice for soil fertilization that consists in adding basic or ultrabasic rocks to the soil so that water, through chemical weathering, decomposes the rock while it gradually releases nutrients."

Jan 1, 2011

By Mingmei Zhu, Lang Hu, Yu Wang, Hongpo Wang, Congjing Zhang

Magnetic field has a great effect on the crystallization behavior of mold flux and properties of the flux film between mold and strand, on which the surface quality of strand was deeply depended in continuous casting process. Therefore, studying the change law of the crystallization properties of mold flux in magnetic field is of great significant. In the present work, based on intensity of the applied magnetic field with the range from 0mT to 60mT, the crystallization ratio, crystal size and mineralogical phases of the flux film were discussed. The results show that crystallization ratio increases with the increasing magnetic field intensity, and the crystal size becomes bigger at the same time. The magnetic field promotes the crystallization ratio and growth speed of the crystallized grains of mold flux. However, magnetic field doesn’t change types of the mineralogical phases.

Jan 1, 2015

By C. D. Seybert, J. W. Evans

"The elimination of convection is essential in experimental investigations of diffusive transport (of heat and matter) during solidification. This paper describes an investigation of an approach whereby a magnetic field gradient is applied to a electrically non-conducting diamagnetic liquid. A magnetic body force then arises which is dependent on the volume susceptibility of the liquid and thereby on the density. With the field gradient aligned vertically and of correct magnitude, the variation of gravitational body forces due to density variations (arising from temperature variations, for example) can be counterbalanced by a variation in magnetic body force.Preparatory to a study of convection control in diamagnetic liquids, PN measurements have been made of the convection occurring during the solidification of water. A peculiar flow arises because of the density maximum at 4°C. Modeling of the flow the steady-state solidification of water in an extremely high field magnet at the NHMFL indicates that flow can be significantly reduced, but it is suggested that, due to field gradient variations within the cell, flow cannot be completely halted. INTRODUCTIONNatural convection is inherently a part of terrestrial solidification. Density-based convection during solidification, due to gradients of temperature and/or concentration, has a significant effect on a material's properties. The design of products with specific material characteristics has required the development of many processes to control convection (such as in the growth of semiconductor crystals, and electromagnetic stirring in steel casting). The expansion of fundamental knowledge about the process of solidification requires collecting data in the absence of density-based convection, while most of science's solidification data (and thus the equations that science has fitted to those data) have been obtained under the influence of gravity. Only relatively recently, through clever experimental design (e.g., drop towers, high altitude parabolic flights, and space laboratories), have investigators been able to study solidification in an environment with ""micro-gravity""."

Jan 1, 2001

By Ahmad-Bitar¸ Riyad N., Shadia J. Ikhmayies

"CdSi-xTex thin films with O<x<0.3 were prepared on glass substrates by the annealing of CdS:In thin films produced by the spray pyrolysis technique. The annealing was performed in nitrogen atmosphere at 400 --,C in the presence of Te vapor. The compositions of the films were determined by energy dispersive X-ray detection (EDAX) measurements. Scanning electron microscopy (SEM) was used to investigate the morphology of the films. The transmittance of the films was measured at room temperature in the wavelength range 400-1100 nm and used to produce the absorbance of the films. The first derivative of the absorbance was used to estimate the optical bandgap energy Eg by using the minima in the first derivative. The relation between the bandgap energy and the fraction x was found to fit with a parabola and bandgaps in the range 2.196: =Eg: =2.480 e V were obtained. Urbach tailing in the bandgap was also investigated.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The fabrication process of these cells involves the deposition of a p-type CdTe absorber layer on top of an n-type CdS one which acts as a window. The efficiency of the solar cell is affected by the method of preparation of both layers [1, 2].Interdiffusion processes taking place at the CdS/CdTe interface have largely been realized to significantly affect the device performance [3] by changing the bandgap of both CdTe and CdS which modifies the spectral response of the solar cell [ 4]. The formation of a mixed crystal or a graded layer causes a reduction in the lattice mismatch at the CdS/CdTe junction [5] which is about 9% [ 6] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [7, 8]. A complete understanding of the properties of the intermixed layers CdSxTe1-x that usually constitutes the interfacial region in the CdS/CdTe solar cell is essential. According to our knowledge, a lot of research was devoted to the investigation of the diffusion of S into CdTe [3-5, 9]; but little on the direct investigation of the diffusion of Te into CdS [6]."

Jan 1, 2011

By Metehan Erdogan, Ishak Karakaya, Fuat Erden, Emre Ergül

"The FFC Cambridge process was suggested as a promising Si production technique for the expanding solar energy industry. Direct electrochemical reduction of bulk SiO2 plates and porous SiO2 pellets in molten CaCl2-NaCl salt mixture were investigated at 750°C by applying 2.8 V potential difference. The produced Si powder was brown and found to be contaminated by the Ni and stainless steel plates used as the cathode contacting materials. The reduction rates of the bulk SiO2 plates and porous SiO2 pellets were compared from variations of current and accumulative electrical charge that passed through the cell during the electrochemical reduction. The amorphous bulk SiO2 plates were reduced slightly faster than porous pellets of crystalline SiO2. The overall reduction potential of SiO2 pellets against the graphite anode at 750°C in molten CaCl2-NaCl salt mixture was determined as 2.3 V by cyclic voltammetry. This potential was supported by calculations.IntroductionMetallurgical grade Si cannot be directly used in electronic industry and some intermediate steps are required to produce industrial solar grade silicon (SOG-Si). A promising alternative solar grade silicon production technique is the FFC Cambridge Process [1]. Production of Si by electrochemical reduction of SiO2 at 850oC in molten CaCl2 electrolyte was first studied by Nohira et.al. [2]. In their study; Si formation was observed on bulk SiO2 cathodes after 1 hour of electrolysis. Complete electrochemical reduction of porous SiO2 pellets was first reported by Jin and his coworkers [3]. The mechanism of electrochemical reduction of SiO2 to Si in molten CaCl2 was explained in another study [4]. Reduction rates of bulk SiO2 and porous SiO2 pellets were also compared previously and it was found that reduction rates for bulk plates were higher [5]. Furthermore, it was reported that mixing Si into porous SiO2 pellet increased the reduction rate [5]. Mo [2, 4-7], Ni [3, 8, 9] or Si [6] were used as cathode contacting materials in various studies. Yasuda et. al. [6] produced Si with 99.80 % purity using Si plates as cathode contacting material to reduce metal contamination."

Jan 1, 2012

By R. M. Westcott

A two-electrode, direct current, slag resistance furnace (SRF) has been constructed and operated to selectively reduce the zinc and lead contents of non-ferrous slags. The experimental SRF is equipped with multiple methods of gas/solids injection for both mixing and reaction. A computer is used to position the electrodes and for data acquisition. A geometric factor correlation was previously developed at Columbia University for calculating the electrical resistance on the basis of furnace geometry and slag conductivity. The experimental SRF was used to test this correlation.

Jan 1, 1994

By Junji Shibata

Heavier rare earth, which is contained in a small amount in ores such as bastnesite and monazite, has been accumulated as a heavier rare earth residue without doing separation and purification due to the lack of suitable methods. The heavier rare earth residue includes seven rare earth elements such as Tb, Dy, Ho, Y, Er, Tm and Yb. Separation and recovery process of Dy, Y, Tm and Yb from leached solution of the heavier rare earth residue was investigated by using a column method with solvent impregnated resin. The solvent impregnated resin was prepared by impregnation of organophosphorous extractant whose trade name is PC-88A into a macro porous resin, Amberlite XAD-7. It was almost impossible to separate them in simple adosorption and elution steps. However, we attained to individually separate Dy, Y, Tm and Yb from the leached solution first by changing eluent concentration gradually from pH2 to 0.02kmol/m3 HC1 in the elution step, and secondly by using a development column and changing eluerit concentration in the elution step. The separation process flow was proposed for a heavier rare earth residue by using the solvent impregnated resin method.

Jan 1, 1998

By K. Dzieciol

The paper presents a study about three image correlation methods ?common cross-correlation, mutual information and phase-correlation ? applied to characterize microstructures reconstructed with X-ray tomography. It is shown that phase correlation is not only the fastest, but also the most sensitive method for detection of similar microstructure features, cavities in the present case. A new image correlation indicator is proposed, which takes into account both the phase shift and the amplitude of similar features in compared images. Some preprocessing aspects related to the tomographic reconstruction and filtering out of characteristic noise are also discussed.

Jan 1, 2009

By Youn-Bae Kang, Jong-Jin Pak, Min-Kyu Paek

The critical evaluation and thermodynamic optimization of Mn-Si-C and its sub-binary systems have been carried out over the whole composition range from room temperature to above the liquidus temperature. The solution properties of the liquid systems have not been clearly described because the liquid solution exhibits a high degree of short-range-ordering. In order to predict the thermodynamics of the liquid solution, the liquid phases were optimized by the modified quasichemical model. The model parameters of the solid phases were also optimized by the compound energy formalism to best reproduce the phase diagram and important thermodynamic properties in Mn-Si-C system. Using the model parameters, various thermodynamic calculations were carried out. The present database will be a part of larger thermodynamic database for the ferromanganese alloy database.

Jan 1, 2014

By M. J. Collins

Pressure leaching of zinc sulphide concentrates has been practiced commercially for nearly two decades. The process, which includes direct leaching of concentrate with spent electrolyte in an autoclave, has been commercialized at four separate locations to date. In pilot studies carried out in the Dynatec lab in Fort Saskatchewan, dozens of additional zinc concentrates have been shown to be amenable to pressure leaching. This paper highlights recent improvements in zinc pressure leaching that have been identified through process development studies, and how the experience gained in these studies has been utilized in the development of a new copper pressure leach process.

Jan 1, 2000

By O. E. Omotoso

This study is part of an ongoing investigation to understand the mechanism of stabilization/solidification of hazardous chromium wastes in ordinary Portland cement (OPC). Tricalcium silicate (C3S*),a major component of OPC is mixed with reagent grade Cr(lll) and Cr(VI) solutions, to simulate complex cementiCr waste systems. Scanning electron microscopy (SEM) and energy disperse spectrometry (EDS) were employed to provide microstructural and chemical information. Transmission electron microscopy (TEMlEDS), apart from complimenting the SEM, was used to probe the distribution of Cr in the hydration products of C3S and to provide crystallographic information. 29Si MAS NMR (magic angle spinning - nuclear magnetic resonance) Was used to characterize the influence of Cr on the hydrated silicate structure.

Jan 1, 1995

By Luis Hoyos-Reyes, Jesus Gonzalez-Trejo, Adriana Cervantes-Clemente, Marco Gutierrez-Villegas, Manuel Palomar-Pardave, Cesar Real-Ramirez

Recent improvements on Peirce-Smith Converters (PSC) have combined numerical and physical simulations. However, most of the physical simulations have been carried out in cold-water models with only one tuyere. Several authors have proved that 2D numerical simulations do not reproduce the hydrodynamic behavior observed in physical simulations. On the other hand, most of the 3D numerical models have used a PSC thin slice with only one tuyere, but symmetric boundary conditions on the virtual walls have been imposed in order to reproduce the behavior of the whole converter. Therefore, there is no coincidence with the rigid walls of the physical models. The aim of this work is to quantify the effect of the virtual walls boundary conditions of a PSC thin slice and to determine the minimum number of tuyeres to characterize the fluid flow behavior of the entire converter.

Jan 1, 2009

By C. J. Parradies

During injection into a die, semi-solid metal alloys exhibit a shear-rate, history-dependent flow response. Simulating the injection of a thixotropic material requires that empirically determined boundary conditions and viscosity are specified as a function of both temperature and shear rate history. Experiments were performed using an industrial die casting machine that was instrumented with sensors to measure the pressure and temperature during the injection of a semi-solid aluminum alloy through a tube. This benchmark experiment was used to develop a simulation of the die casting process that could then be applied to more complex die geometries. The results of the experiments were analyzed using the exact, steady state solution for a power law fluid and simulations accounting for slipping at the boundary between the semi-solid metal and the die. Results indicated that the no-slip condition cannot be used to simulate the velocity boundary condition, because the measured pressure is much lower than that predicted by the models. An estimated apparent slip coefficient was introduced to account for the reduced pressure. During some of the experiments, a sudden drop in the measured pressured, prior to decreasing the ram velocity, coincided with observations of segregation in the form of concentric rings visible on the polished surface of cross-sections cut from material remaining in the tube.

Jan 1, 1997

By R Bartlett

Process engineering-science originally developed for percolation leaching of ore in heaps is extended to the decontamination of unsaturated soil, either in situ or after excavation and emplacement as a soil heap on an impervious pad. Phenomena considered include: soil matrix porosity and permeability; percolating solution retention, capillarity and flow; washing sweep efficiency; optimum solution application rates during leaching; soil agglomeration to improve soil permeability and soluble contaminant transport by diffusion in soil agglomerates. Practical aspects briefly discussed include leach pad construction, solution distribution and recovery from the soil, and solution containment.

Jan 1, 1994

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987

By Kunwar Pal, S. K. Tyagi, A. K. Pandey

"This study deals with the performance evaluation, technical and environmental aspects of different cookstove models (NIRE-02, NIRE-03 & NIRE-04). These cookstove models were designed, fabricated and evaluated following Bureau of Indian Standards (BIS) and their performance was compared from technical and environmental points of views. The theoretical efficiencies of all the cookstove models are found to be in good agreement with the experimental one. Also, the overall performance of these models is found to be in the order of (NIRE-04 > NIRE-03 > NIRE-02) which is also observed to be much better than that of the traditional cookstoves being used by the people in most of the developing countries around the world. The CO2 emission reduction from these models is found to be between 2.0-3.0 tons per household annually which is ultimately in good agreement with the experimental values.IntroductionMore than 2.5 billion people around the world depends on the biomass based resources for cooking and heating applications which includes wood, cattle dung, charcoal and agriculture residue [1,2]. Generally, people of rural area cook their food on unvented open fire, which burn biomass fuel inefficiently besides it creates many thermal and environment pollution hazardous causing health problems in the women and girl children due to more exposure of emissions. Also the consumption of biomass is very high as compared to the fossil fuels due to the fact that the large population of the developing countries lives in the rural area than that of in the urban area. It is estimated that about 3% of the diseases are caused due to incomplete combustion of biomass, which results in the around 1.8 million premature death every year including around 0.9 million death under five year of their age [3,4].Ramanathan and Carmichael [5] recently found that the black carbon of unburned smoke is playing a major role in global warming. The emission factors for different combinations of fuel and stove tested in China for direct and indirect GHGs as well as other airborne pollutants such as, CO2, CO, CH4, TNMHC, N2O, SOx, NOx, TSP etc. for a typical set of operating parameters [6]. The improved biomass cookstove technology came into assistance which is technically feasible, socially reliable and economically viable [7, 8]. The improved biomass cookstove not only reduces pressure on the biomass resource, but also reduces the environmental pollution and also minimize the time required for collection of fuel wood [9, 10]. Sharma et al. [11] emphasized on the adoption and large-scale propagation of efficient stoves to improve the health of rural women and to reduce the consumption of firewood and environmental pollution."

Jan 1, 2014

By K. W. Cathrine Solem

Filtration of liquid aluminium is widely used in the industry for the removal of inclusions, and Ceramic Foam Filters (CFFs) are often the filtration media of choice. It is known that PH3 (phosphine) can be released from used phosphate bonded CFFs when in contact with water. Additionally, there is a need of an improved understanding of the thermal stability and the chemical reactivity of these types of filters, as there is limited information available in the public domain. In the present preliminary study, three CFFs, i.e. Substrate 1–3, with varying AlPO4 (aluminium phosphate) content were studied under controlled conditions. Samples of the substrates, as produced and in contact with 5N pure aluminium, were heat-treated in a vacuum induction furnace at 850 °C and 1300 °C, as well as thermally studied at 850 °C using a Differential Scanning Colorimeter connected to a Thermogravimetric Analyser (DSC-TG). All tests were performed under an inert atmosphere of argon (Ar). Mass changes of ∼0.001 % were registered for the pure substrates, and 0.003-0.10 % when in contact with aluminium. In the latter case, diffusion of P (phosphorous) from the bulk of the substrate to the interface was established to have taken place. A colour change, from white to orange/brown, was also observed at the interface, which is a clear sign that a chemical reaction has taken place. As a result, the thermal stability of the substrates can be questioned under present conditions.