Search Documents

By T. Shibasaki

There is a strong demand in the photo industry to the higher quality of refined silver. Osaka Refinery produces about 27 mtpm of refined silver mainly from copper refinery slimes. Product quality is attained by controlling the impurity level in electrolyte. Copper is cemented with silver oxide and palladium is precipitated by a chelating agent. Both processes were operated previously in batchwise for treatment of bled out electrolyte, Recently these processes have been improved and made continuous to cope with the increased impurity.load. As a result the grade of fine silver has been maintained steadily at Pd < 3 ppm and Cu < 5 ppm.

Jan 1, 1989

By M. Misra

The bacterium?Mvcobacterium Phlei has a demonstrated potential to be used for the flocculation of a variety of finely divided minerals. The microorganism possesses both hydrophobic surface and high negatively electrostatic charge. It can adhere to many mineral surfaces ?if the charge and hydrophobic interaction? between the microorganism and the minerals are favorable to adhesion. Experimental results showed that the dolomitic phosphate slime from Florida and fine hematite can be :readily flocculated from dilute suspension.. In the case of dolomitic phosphate slime, a consolidated sediment containing 24&apos;-25 weight% :solids can be obtained from .a dilute slurry .in a short time. Sediments obtained from hematite flocculation are rather massive and more .consolidated than phosphate slime. Mycobacterium Phlei has a specificity for selective flocculation of hydrophobic fine coal particles from pyrite and ash containing minerals. Because of mutual hydrophobic interaction of coal and Mycobacterium Phlei, it was noticed that coal particles appear to be strongly held in the aggregate by adhesion or bridging of bacteria. However, Mycobacterium Phlei is not a good flocculant for either associated pyrite or ash present in coal.

Jan 1, 1991

By E. S. Geskin, W. L. Chen, A. Vora

"This paper is concerned with the application of an abrasive waterjet for metal shaping. The waterjet cutting technology uses water compressed to the pressure up to 55,000 psia which is accelerated in a cylindric nozzle. Abrasive particles are then supplied into the water stream and accelerated by the water. Cutting occurs via the interaction between the water-particles stream and a workpiece that causes material erosion at the impingement zone. The mechanism of this interaction enables shaping of practically any material with a minimal effect on the metallurgy of subsurface. The motion of the jet penetrating through a material body is guided by a robotic arm. A waterjet cutter is becoming one of the principal tools for shaping titanium, super-alloys and other hard-to-machine metals and composites. The shaping, resulting from the waterjet cutter, is very similar to laser beam cutting. However, unlike laser processing, there is no damage to the subsurface structure.The presented work discusses the experimental study of cutting of titanium plates. The results of these experiments demonstrate the potential of the abrasive waterjet as a shaping tool. IntroductionOne of the main avenues in the development of metal shaping is the use of high energy beams as cutting tools (1,2). There are a number of advanced beam oriented material removal technologies, such as laser, electron beam, plasma and abrasive waterjet (AWJ) cutting. The advantages of AWJ cutting are well understood and documented (3-14). This technology has the potential of becoming the principal tool for netshaping and netsurfacing of parts. However, the use of AWJ is currently limited to cutting of hard-to-machine materials such as titanium, superalloys, glass, composites, etc. The cost of A W J cutting is much higher and the productivity is much lower than those of the thermal cutting. At the same time abrasive waterjet can be used for shaping any existing technological material from fabrics, plastics, aluminum to glass, composites, and diamonds. The material losses during AWJ shaping are minimal. The roughness and waveness of the surfaces generated during AWJ cutting are substantially less than those of the thermal cutting. Due to the size of the jet cross-section total force exerted by the jet on a workpiece does not exceed 30-50 newtons. This terminates the need in the use of complex fixture for material holding. Low applied forces and low surface temperature prevent the damage of metal subsurface in the course of cutting. The small size of the impingement area will determine the limited width of the kerf. Due to the size of kerf and unidirectional character of the water jet the formation of practically any metal contour is possible."

Jan 1, 1988

By Michael B. Tessieri

With the increasing environmental demands and higher fuel efficiency standards on auto manufacturers, the use of aluminum in automotive applications is expected to show significant growth for the balance of this decade. Cast and wrought aluminum usage is reviewed by auto part, and alloy family for the year 2000 automobile. The analysis addresses the effect of this increased volume on the recycling infrastructure and identifies issues and opportunities, which will face the recycling industry.

Jan 1, 1995

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By Chuang Y-Y

A summary is made on the thermodynamic analysis for two of the four ternary systems of the quaternary Cu-Fe-Ni-S. The analysis is being extended to ternary Cu-Fe-S and then to the quaternary. An analysis is already made for the metal ternary but is not reported here. Experiment is being carried out to measure the liquidus surface. of Fe-Ni-S equilbrium with the fcc solid solutions of (Fe, Ni). The presentation at the Symposium will include all the results obtained at the time of presentation.

Jan 1, 1983

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By D. C. Foguel, J. L. R. Bravo

For several years, Caraiba Metais S.A. (CMSA) had to stock the arsenic sludge generated from the electrolyte purification process of its tankhouse. The amount stocked · reached approximately 3,500 tonnes, as the effects of its recycling during the smelting process and consequently in the sulfuric acid plant were unknown. Besides, it had as limiting factors the high content of arsenic in the copper concentrates supplied by foreign countries as well as the reduced capacity of the tankhouse's purification plant. The choice for selling the mentioned residue, which generally contains more than 50% of Cu, was attractive, but the environmental policies and regulations had not allowed this option. Other alternatives, such as the production of bicupric arsenic by means of a solvent extraction process or arsenic trioxide, were considered but the economic feasibility was not attractive due to the absence of a domestic market and a poor international market. After a study of the arsenic partition in the metallurgical process, it was verified that the residue could be recycled without causing any operational problems or damage to the environment. To make this possible, the capacity of the purification plant was increased and the way of removing the arsenic sludge from the cells was modified from manual to mechanical, therefore avoiding the direct contact of the workers with this poisonous substance. Moreover, procedures for recycling in the smelter were established and tolerance limits were set for both the smelter and the sulfuric acid plant. The main amount of arsenic to be recycled is released with the smelting furnace off-gas, which is washed during the purification stage of the sulfuric acid plant. The acid water, rich in arsenic, is then treated in the waste plant and the arsenic, in its stabilized condition, is confined in an appropriate area.

Jan 1, 2000

By James C. Foley, David K. Rehbein

"In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent ·advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ evaluations of the acoustic attenuation and velocity as sintering proceeds. Pure aluminum (99.999%) and aluminum alloy powders were prepared with high-pressure gas atomization (HPGA). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and attenuation during sintering. The changes in acoustic properties were correlated with sample microstructures and mechanical properties. Evolution of the acoustic echo train during sintering is shown to provide information on the state of sintering as well as having the potential for detection of interior flaws.IntroductionThe versatility of powder metalallurgy (PIM) technology in the manufacture of complex shapes has enabled an increasing amount of wrought and casting production capacity to be converted to PIM technology. However, ultrasonic inspection of green components produced using PIM techniques remains a challenge and is not generally practiced [1]. Inspection of PIM components in the green state is highly desirable, because the green part can be reclaimed with only accepted components being subjected to further costly processing. Another potential benefit is characterization and greater understanding of the sintering process itself. An increased scientific understanding of the sintering process enables intelligent process control, greater reliability of the production process and a lower rate of rejection of the finished product. In order to realize these potential benefits, it is necessary therefore that accept/reject criterion be based on real time nondestructive evaluation of the green-state components and the sintering process.Most current nondestructive inspection techniques suffer from their inability to perform inspections below the near-surface region with the exception of X-ray and to some extent pulsed eddy current [2]. X-ray inspection requires extensive shielding of production personnel and expensive film and film processing. While development of pulsed eddy current techniques have lessened the impact of the well-known skin effect, the depth of penetration of the induced eddy currents remains somewhat of an issue [2]."

Jan 1, 2000

By Thomas M. Harris

Cation exchange is not sufficiently selective to be used for the removal of heavy metal ions from a general industrial wastewater. However, if the metals can be converted to polyvalent anions through complexation, they may be removed both selectively and efficiently by anion exchange. This approach, referred to as chelation-assisted anion exchange (CAAE), has been examined using industrial wastewater samples contaminated with Ni2+ and Cr3+. For this particular application, the Ni2+ is complexed with 8-hydroxyquinoline-5-sulfonic acid, and the Cr3+ with sulfosalicylic acid. Removal efficiencies and adsorption isotherms for both the complexants and the complexes were determined in batch-mode tests.

Jan 1, 1994

By Luis W. Pommier

Large quantities of sea sludge containing halogenated organic compounds, such as PCB, oils and metals like arsenic and lead have accumulated throughout the years at the bottom of sea channels and harbors and are obstructing navigation and creating environmental problems which need to be resolved. A sludge from a California port would be dredged by suction pumps, it would be processed in a plant which would be built either on firm soil or on floating platforms. The sludge shows contents of up to 1 ppm of PCB, 15 % oil and 10 ppm of arsenic, which generates a very fetid odor. Bench scale work indicates that most of the contamination concentrates on the solid phase, in fact, only minor amounts of oil report to the sea water and can be readily removed by physical means. After separation of the sea water from the solids of the sludge by decantation, it is possible to solubilize the PCB, the oil and the metals into an organic solvent leaving a non-hazardous soil for disposal near the harbor. The PCB is dehalogenated during the solubilization process leaving a liquor solution containing the oil and metals. The oil is extracted leaving an aqueous solution containing the arsenic. Further process extracts the arsenic from this solution rendering the liquid non-hazardous. Transportation and disposal of the sludge is impractical. There are hundreds of thousands of tons of hazardous soils accumulated in each harbor, which would fill the hazardous waste disposal sites available and it would be, prohibitively expensive to do so. It is not possible to compare the costs of decontamination with a competitive method. If it were, the proposed process would be less expensive than transportation and disposal and it has the advantage of removing the liabilities from the Responsible party. After a full scale continuous pilot project is run to decontaminate a small, 500 cubic yards accumulation of this type of sludge in a California harbor, a full scale environmental project would be initiated. The decontamination of one million tons of sludge would be completed in five years.

Jan 1, 1995

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By C. M. Diaz

The chemistry of the main unit processes in nickel extractive pyrometallurgy is reviewed. Key re1a ions between smelter feed composition and process selection are discussed, with particular reference to operating conditions, energy requirements and products. The paper a1 so includes a brief discussion of current nickel smelters, based on the results of a recent survey carried out by TMS.

Jan 1, 1988

By Hiroyuki Sano

A closed recycling process for the low-grade scrap of Al-based composite materials was developed. In this process flux treatment with water-soluble halide is a key technique. In the present work, flux treatment conditions were discussed from the viewpoint of the separation and the recovery of the base material, reinforcement and flux. Optimum separation condition was obtained for the NaCl-KCI-KF flux treatment. The recovered aluminum alloy can be recycled for various usages. The recovered SiC particles cannot be reused as reinforcement because of the coexistence of the contamination, therefore it is necessary to eliminate these contaminates or to find another use. The recovered flux is reusable with supplemental addition of fluoride.

Jan 1, 2003

By C. Landolt

Inco&apos;s Copper Cliff Smelter Complex produces some 11 5,000 tonnes per year of nickel and 120,000 tonnes per year of copper. The Smelter flowsheet has changed a number of times over the years. The most recent changes were effected in the mid-1980&apos;s in response to new realities in metal markets and heightened awareness about the workplace environment. By 1994, the flowsheet will undergo yet another metamorphosis as part of Inco&apos;s SO2 Abatement Program. The paper discusses the improvements implemented during the 1980&apos;s and projects the processing in the Smelter through 1994.

Jan 1, 1993

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"A simplified finite-difference time-domain (FDTD) algorithm for modeling microwave propagation in magnetic dielectric materials was developed and employed to study the microwave dissipation in magnetite. Heat transfer during microwave heating of magnetite was subsequently investigated by solving heat transfer differential equation using explicit finite-difference (EFD) method. It is observed that temperature of magnetite surface increases rapidly in the first minute due to the rapid strength decays in both electric and magnetic fields within a short distance along the path of microwave dissipation. A temperature peak, initially formed at the surface of the sample slab, migrates inward as heating time extends and microwave power increases.IntroductionAs one of primary materials in iron and steel industry, magnetite exhibits excellent microwave absorption capability, which leads to great energy conservation in microwave assisted steelmaking [1,2]. The fast temperature increase in microwave heating of magnetite can be attributed to both dielectric and magnetic losses [2]. Although much experimental work has confirmed this observation, detailed computational studies for modeling of microwave field dissipation in magnetite at commonly used frequencies, such as 915 MHz, has not been well addressed [1,3].Finite-difference time-domain (FDTD) method is widely used in computational electrodynamics modeling to simulate the dynamics of electromagnetic wave scattering from various media [4,5]. This approach requires modeling algorithm to be formulated with integration of specific characteristics of each medium. An extensive literature survey indicates that current formulations are only suitable for modeling electromagnetic waves propagating in normal dielectric lossy materials [5,6]. Since magnetite is a magnetic dielectric material in which both dielectric and magnetic properties contribute to the heating process under microwave irradiation, a specific algorithm should be developed for the simulation."

Jan 1, 2012

By Cassandre Nowicki, Louis Gosselin, Carl Duchesne

"Quebec's primary aluminium production industry consumes roughly 39 TWh of electricity per year and is accountable for roughly 7 million tons of CO2 equivalent. By tapping only a small portion of waste heat and integrating it inside the production facility itself, we can significantly reduce GHG emissions and energy consumption. Although the amount of thermal waste can be adequately estimated by applying an energy balance to production processes, this provides very little information on the quality of waste heat and its potential for integration. A measure of exergy is required. Waste heat streams characterized by high exergy content may generally offer valuable incentives for recovery and integration. More generally, exergy values limit integration possibilities. An exergy analysis is provided for the aluminium electrolytic reduction process. This is meant to guide future heat recovery initiatives and energy efficiency measures.IntroductionCanada is one of the world leaders in primary aluminium production and 92% of its aluminium production capacities are located in the province of Quebec. In 2007, production capacity reached 2,786,000 tons in Quebec alone. Since it is estimated that 2.5 equivalent tons ofCO2 are released for each ton of aluminium produced in Canada, Quebec's aluminium production industry is accountable for roughly 7 million tons of CO2 yearly [1, 2]. Furthermore, with an average electricity consumption of 14 MWh per ton, primary aluminium accounts for 39 TWh of electricity per year in Quebec and this energy consumption represents 350 thousand tons ofCO2 equivalent [3, 4]. Natural gas consumption associated with primary aluminium production accounts for less than 1 TWh, but it represents an additional 350 thousand tons of CO2 equivalent [ 4].This work is meant to provide a tool to guide future efforts towards heat recovery and energy efficiency in the primary aluminium industry. Waste heat recovery and thermal integration can cut down both energy consumption costs and GHG emissions. In a primary aluminium production facility, waste heat represents roughly half of the energy input into the Hall-Heroult process. Tapping only a small portion of this energy could reduce natural gas and electricity consumption significantly. In order to evaluate how much of this energy is actually usable, we propose to apply an exergy analysis to individual transformation processes in an aluminium production facility, such that a potential to do work can be assigned to every waste heat flux. The approach will be described in the next section."

Jan 1, 2012

By T. Manlyama

The Tamano Smelter of Hibi Kyodo Smelting CO., Ltd. went into operation in 1972. The Flash Smelting Furnace that was originally adapted was equipped with electrodes that were attached to the settler substitute of the slag cleaning furnace. Later the development of our own original coke combustion technology was promoted and a new Tamano Type Flash Smelting Furnace (T-FSF), without electrodes, was put into operation in 1988, T he technology of coke combustion and combustion the burner have continued to improve. As a result the copper losses in the Wag have been reduced as well as a stable operation has been achieved, Furthermore; this has been accomplished while increasing the concentration feed and the matte grade. The current objective is to continue to strive for high matte grade operation and to raise production efficiency while paying attention to the important subject of copper losses in the slag. In this report, the data related to the copper loss in the slag reduction are presented along with the influence of the thickness, settling time and coke. The recent operation conditions of the T-FSF are also presented.

Jan 1, 2003

By William Brinkman, Mark Jolly, Nasim Soleimanian, Karl Dearn, Oliver Brinkman

"Glass manufacturing is a heat intensive process. There is a direct correlation between the batch distribution techniques and the furnace energy consumption, productivity, and quality of the glass manufactured. All four major segments (float, container, fibre, and specialty glasses) would benefit from using an optimised batch distribution technique where possible. Oscillating batch chargers (OBC) have been in use since the early 70s, despite their superior batch shape, coverage, and in turn positive effects on the energy consumption and productivity of the furnace they are almost exclusively used in container glass manufacturing. The OBC’s main difference compared with other charging methods is its ability to directly influence the batch initial velocity. This paper reports on results achieved in CFD models (GFM) used to study effect of the machine on the overall energy consumption in the doghouse and the melt space.IntroductionGlass manufacturing can be divided to four major segments float glass, container glass, fiberglass, and specialty glasses. The financial cost of manufacture, its impact on the environment, lack of standardisation and mounting pressure imposed by the authorities for reduction in emissions means that the industry and its suppliers are utilising CFD modelling in order to tackle these challenges. The need for high temperature to create and maintain the viscous flow, homogenisation of the glass melt, and maintenance of the process to allow continuous output of glass of the right quality are the contributors to the energy intensive activities that are involved in continuous glass manufacturing. This in turn has resulted in design of large container glass furnaces which have high energy consumption, low specific performance, and high CO2 emissions where the most efficient furnaces in the container glass sector have a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch making even very small improvements in efficiency by operation optimisation a value adding activity [1-14].The theoretical calculated energy required to melt glass is 2 to 3 times less than the energy actually used to melt glass as a result of glass melt passing a zone 5 to 8 times before leaving the tank.[8]. This causes contamination as the result of mixing between the completely molten glass free from bubbles returning to the batch area where there is freshly molten non-homogeneous glass, still containing very large numbers of bubbles and un-molten batch. At high temperature some components are dissolved rather than melted. Given that an un-molten batch is a good thermal insulator, it can be transported a long way into the furnace, increasing the need for homogenization which also increases the glass residence time of glass melt. This is why large unbroken strings of batch should be avoided, as should an overall blanket without gaps."

Jan 1, 2014

By Jinliang Zhang, Jian Pan, Deqing Zhu

"Limestone and burnt magnesite were added to vary MgO content and basicity (CaO/SiO2 ratio) of pellets for investigating their influences on the properties of specularite pellets. At fixed MgO content, the addition of limestone does not affect on the properties of green balls significantly. The addition of burnt magnesite has obvious influence on the quality of green balls, especially on the thermal shock temperature. Without burnt magnesite, the thermal shock temperatures are about 400°C, and, the thermal shock temperature increases to 600~630°C by adding burnt magnesite. For preheated pellets, when the burnt magnesite is added, the compressive strength will be decreased. For roasted pellets without burnt magnesite, the calcium additives can form binding phase of calcium-ferrite, and suitable liquid phase will improve recrystallization of hematite, but excessive liquid will destroy the structure of pellets, so the compressive strength of pellet increases firstly and then decreases. When adding burnt magnesite, the compressive strength will increase as the basicity increases. When the basicity is more than 0.2, the compressive strength of the pellets various MgO content and basicity is above 2500N/pellet and then MgO-bearing fluxes can be added to prepare pellets with good high temperature properties.IntroductionWith the rapid development of the steel industry in China, oxidized pellets, possessing good mechanical and metallurgical properties, are becoming indispensable burdens for blast furnace ironmaking [1-3]. However, this has resulted in the shortage of domestic iron concentrates, so many Chinese steel plants begin to use imported hematite concentrate to prepare pellets. Compared with magnetite pellets, the hematite pellets require high roasting temperature and narrow roasting temperature range (1300–1350°C) and possess low compressive strength [4,5].1"

Jan 1, 2012